Toro Rear Deflector Kit, TimeCutter ZD Series Riding Mower Installation guide

Rear Deflector Kit, TimeCutter ZD Series Riding Mower
Toro
Brand
Toro
Model
Rear Deflector Kit, TimeCutter ZD Series Riding Mower
Category
Wall & ceiling mounts accessories
Type
Installation guide

Toro Rear Deflector Kit, TimeCutter ZD Series Riding Mower mounts to the back of the heat shield, preventing grass clippings and debris from being discharged toward the operator. Its easy installation process includes removing the collection bag, installing the deflector locking pins, and finally securing the deflector. Once installed, the deflector can be swung down and secured using hairpin cotters.

Toro Rear Deflector Kit, TimeCutter ZD Series Riding Mower mounts to the back of the heat shield, preventing grass clippings and debris from being discharged toward the operator. Its easy installation process includes removing the collection bag, installing the deflector locking pins, and finally securing the deflector. Once installed, the deflector can be swung down and secured using hairpin cotters.

Form No. 3356-697 Rev A
Rear Deector Kit
For TimeCutter® ZD Series Riding Mower
Model No. 74435
Installation Instructions
Installation
Loose Parts
Use the chart below to verify that all parts have been shipped.
Step
Description
Qty.
Use
1
No parts required
–
Remove the collection bag.
Deector locking pin
2
2
Flange-head bolts
4
Install the deector locking pins.
Deector
1
3
Hairpin cotter
2
Install the deector.
Step
1
Removing the Collection
Bag
No Parts Required
Procedure
T he collection bag is retained in the engine co v er
b y seating the lev er side pin into a holed brac k et in
the right hand side of the engine co v er . R emo v e it
as follo ws:
1. P ark the mac hine on a flat, lev el surface , stop
the engine , remo v e the k ey , and w ait for all
mo ving par ts to stop .
2. Raise the bag up and first lift the pin in the
open notc h up and a w a y from the hood. T hen
slide the lev er side pin out the brac k et until the
bag is clear of the mac hine ( Figure 1 ).
Figure 1
1. Collection bag 4. Collection bag pin
2. Engine hood 5. Notched bracket
3. Holed bracket
© 2006—The Toro® Company
8111 Lyndale Avenue South
Bloomington, MN 55420
Register at www.Toro.com. Original Instructions (EN)
Printed in the USA.
All Rights Reserved
Step
2
Installing the Deector
Locking Pins
Parts needed for this step:
2
Deector locking pin
4
Flange-head bolts
Procedure
With the pins facing outw ard, install the deflector
loc king pins to the bac k of the heat shield using 4
flang e-head bolts , as illustrated in Figure 2 .
Figure 2
1. Heat shield 3. Flange head bolt
2. Deector locking pin
Step
3
Installing the Deector
Parts needed for this step:
1
Deector
2
Hairpin cotter
Procedure
1. Seat the right-hand pin located on top of the
deflector into the hole on top of the engine
hood, and then seat the opposing pin into the
notc h on the top of the engine hood ( Figure 3 )
Figure 3
2
2. Swing the deflector do wn and pull the sides
outw ard slightly , inser ting the deflector loc king
pins through the holes in the sides of the
deflector ( Figure 4 ).
Figure 4
1. Deector
3. Hairpin cotter
2. Deector locking pin
3. Secure the deflector to the loc king pins using
tw o hair pin cotters ( Figure 4 ).
3
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Toro Rear Deflector Kit, TimeCutter ZD Series Riding Mower Installation guide

Rear Deflector Kit, TimeCutter ZD Series Riding Mower
Toro
Brand
Toro
Model
Rear Deflector Kit, TimeCutter ZD Series Riding Mower
Category
Wall & ceiling mounts accessories
Type
Installation guide

Toro Rear Deflector Kit, TimeCutter ZD Series Riding Mower mounts to the back of the heat shield, preventing grass clippings and debris from being discharged toward the operator. Its easy installation process includes removing the collection bag, installing the deflector locking pins, and finally securing the deflector. Once installed, the deflector can be swung down and secured using hairpin cotters.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers