Jenn-Air JXI8536DS0 Owner's manual

Brand: Jenn-Air

Model: JXI8536DS0

Category: Cooker hoods

Type: Owner's manual

JENN-AIR

36" (91.4 CM) ISLAND CANOPY

RANGE HOOD

HOTTE DE CUISINIÈRE JENN-AIR

POUR ÎLOT DE

36" ET (91,4 CM)

Installation Instructions and Use & Care Guide

For questions about features, operation/performance, parts, accessories, or service in the U.S.A., call:

1-800-JENNAIR (1-800-536-6247) or visit our website at www.jennair.com.

In Canada, call: 1-800-JENNAIR (1-800-536-6247), or visit our website at www.jennair.ca.

Instructions d’installation et Guide d’utilisation et d’entretien

Au Canada, pour assistance, installation ou service, composez le 1-800-JENNAIR (1-800-536-6247) ou visitez notre site web à

www.jennair.ca.

Table of Contents/Table des matières ............ 2

IMPORTANT: READ AND SAVE THESE INSTRUCTIONS.

FOR RESIDENTIAL USE ONLY.

IMPORTANT : LIRE ET CONSERVER CES INSTRUCTIONS.

POUR UTILISATION RÉSIDENTIELLE UNIQUEMENT.

LI32KB/W10674115D

TABLE OF CONTENTS

RANGE HOOD SAFETY .................................................................2

INSTALLATION REQUIREMENTS ................................................4

Tools and Parts ............................................................................4

Location Requirements................................................................4

Venting Requirements..................................................................5

Electrical Requirements ...............................................................6

INSTALLATION INSTRUCTIONS ..................................................7

Prepare Location..........................................................................7

Assemble and Install Range Hood ..............................................7

Make Electrical Connection .........................................................8

Install Duct Covers.......................................................................9

Complete Installation .................................................................10

RANGE HOOD USE......................................................................11

Controls and Features................................................................11

RANGE HOOD CARE ...................................................................12

Cleaning......................................................................................12

WIRING DIAGRAM ......................................................................13

ASSISTANCE OR SERVICE.........................................................14

In the U.S.A. ...............................................................................14

In Canada ...................................................................................14

Accessories................................................................................14

WARRANTY .................................................................................15

TABLE DES MATIÈRES

SÉCURITÉ DE LA HOTTE DE CUISINIÈRE................................16

EXIGENCES D'INSTALLATION...................................................18

Outils et pièces...........................................................................18

Exigences d'emplacement.........................................................18

Exigences concernant l'évacuation ...........................................19

Spécifications électriques ..........................................................21

INSTRUCTIONS D’INSTALLATION.............................................21

Préparation de l’emplacement...................................................21

Assemblage et installation de la hotte .......................................22

Raccordement électrique...........................................................23

Installation des cache-conduits .................................................24

Achever l'installation ..................................................................26

UTILISATION DE LA HOTTE .......................................................26

Commandes et caractéristiques................................................26

ENTRETIEN DE LA HOTTE..........................................................28

Nettoyage ...................................................................................28

SCHÉMA DE CÂBLAGE ..............................................................29

ASSISTANCE OU SERVICE.........................................................30

Au Canada..................................................................................30

Accessoires ................................................................................30

GARANTIE.....................................................................................31

RANGE HOOD SAFETY

You can be killed or seriously injured if you don't immediately

You

can be killed or seriously injured if you don't

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can

happen if the instructions are not followed.

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.”

These words mean:

follow instructions.

instructions.

DANGER

WARNING

State of California Proposition 65 Warnings:

WARNING: This product contains one or more chemicals known to the State of California to cause cancer.

WARNING: This product contains one or more chemicals known to the State of California to cause birth defects or other

reproductive harm.

IMPORTANT SAFETY INSTRUCTIONS

READ AND SAVE THESE INSTRUCTIONS

INSTALLATION REQUIREMENTS

Tools and Parts

Gather the required tools and parts before starting installation.

Read and follow the instructions provided with any tools listed

here.

Tools needed

■ Level

■ Drill with 1¼" (3.0 cm), ³⁄₈" (9.5 mm), ⁷⁄₆₄" (2.75 mm) and

¹⁄₈" (3.0 mm) drill bits

■ Pilot hole drill bits (determined by chimney support

attachment method)

■ Pencil

■ Wire stripper or utility knife

■ Tape measure or ruler

■ Pliers

■ Caulking gun and weatherproof caulking compound

■ Vent clamps

■ Jigsaw or keyhole saw

■ Flat-blade screwdriver

■ Metal snips

■ Phillips screwdriver

Parts needed

■ Home power supply cable

■ ½" (12.7 mm) UL listed or CSA approved strain reliefs (2)

■ UL listed wire connectors (3)

For vented installations, you will also need:

■ Wall or roof cap

■ Metal vent system

For non-vented (recirculating) installations, you will also

need:

■ Recirculating Kit Part Number W10692909 for non-vented

(recirculating) installations only. See “Assistance or Service”

section to order.

■ 6" (15.2 cm) round metal vent duct. Length required is

determined by ceiling height.

Parts Supplied

Remove parts from packages. Check that all parts are included.

■ Hood canopy assembly with ventilator and LED light installed

■ Filter—installed in hood canopy

■ 4.2 x 8 mm screws (60)

■ 5 x 45 mm screws (4)

■ Mounting template

■ Upper vent covers (2)

■ Lower vent covers (2)

■ Vent transition with backdraft damper installed

■ 3.5 x 9.5 mm mounting screws (2)

■ Plastic vent clips (4)

■ Upper horizontal support bracket

■ Horizontal support

■ Vertical supports (8)

■ 3.5 x 6.5 mm screws (4)

■ 2.9 x 3 mm screws (2)

■ T10

Torx

®†

adapter

■ T20

Torx

adapter

Location Requirements

IMPORTANT: Observe all governing codes and ordinances.

Have a qualified technician install the range hood. It is the

installer's responsibility to comply with installation clearances

specified on the model/serial/rating plate. The model/serial/rating

plate is located behind the left filter on the rear wall of the vent

hood.

Canopy hood location should be away from strong draft areas,

such as windows, doors and strong heating vents.

Cabinet opening dimensions that are shown must be used. Given

dimensions provide minimum clearance.

Grounded electrical outlet is required. See “Electrical

Requirements” section.

Because of the size and weight of this island hood, the chimney

support must be securely attached to the ceiling.

■ For plaster or drywall ceilings, the chimney support must be

attached to joists. If this is not possible, you must build a

support structure behind the plaster or drywall. The support

structure must be able to support 100 lbs (45.4 kg).

This range hood is recommended for use with cooktops with a

maximum total rating of 78,000 BTUs or less.

The range hood is factory set for venting through the roof.

For non-vented (recirculating) installation, see “Non-vented

(recirculating) Installations” in “Assemble and Install Range

Hood” section. Recirculation Kit Part Number W10692909 is

available from your dealer or an authorized parts distributor.

All openings in ceiling and wall where range hood will be installed

must be sealed.

For Mobile Home Installations

The installation of this range hood must conform to the

Manufactured Home Construction Safety Standards, Title 24

CFR, Part 328 (formerly the Federal Standard for Mobile Home

Construction and Safety, Title 24, HUD, Part 280) or when such

standard is not applicable, the standard for Manufactured Home

Installation 1982 (Manufactured Home Sites, Communities and

Setups) ANSI A225.1/NFPA 501A, or latest edition, or with local

codes.

Product Dimensions

*Vented installations only

**Non-vented (recirculating) installations only

†®TORX, T10 and T20 are registered trademarks of Acument Intellectual Properties, LLC.

12¹⁄₄"

(31.0 cm)

13³⁄₁₆"

(33.5 cm)

36" (91.2 cm)

*32¹⁄₂"

(82.6 cm)

min.

*46¹⁄₂"

(118.0 cm)

max.

**32¹⁄₂"

(82.6 cm)

min.

**52⁹⁄₁₆"

(133.5 cm)

max.

27" (68.6 cm)

Installation Dimensions

IMPORTANT:

Minimum distance “C”: 24" (61.0 cm) from electric cooking

surface.

Minimum distance “C”: 27" (68.6 cm) from gas cooking

surface.

Suggested maximum distance “C”: 36" (91.4 cm)

The chimneys can be adjusted for different ceiling heights. See

the following chart.

*NOTE: The range hood chimneys are adjustable and designed

to meet varying ceiling or soffit heights depending on the

distance “C” between the bottom of the range hood and the

cooking surface. For higher ceilings, a Stainless Steel Chimney

Extension Kit Part Number W10688278 is available from your

dealer or an authorized parts distributor. The chimney extension

replaces the upper chimney shipped with the range hood.

Venting Requirements

■ Vent system must terminate to the outside, except for non-

vented (recirculating) installations.

■ Do not terminate the vent system in an attic or other enclosed

area.

■ Do not use 4" (10.2 cm) laundry-type wall caps.

■ Use metal vent only. Rigid metal vent is recommended. Do

not use plastic or metal foil vent.

■ The vent system must have a damper. If the roof or wall cap

has a damper, do not use the damper supplied with the range

hood.

For the most efficient and quiet operation:

■ Use a straight run or as few elbows as possible.

■ Use no more than three 90° elbows.

■ Make sure there is a minimum of 24" (61.0 cm) of straight

vent between the elbows, if more than 1 elbow is used.

■ Do not install 2 elbows together.

■ Use vent clamps to seal all joints in the vent system.

■ Use caulking to seal exterior wall or roof opening around the

cap.

■ The size of the vent should be uniform.

Cold Weather Installations

An additional back draft damper should be installed to minimize

backward cold airflow and a thermal break should be installed to

minimize conduction of outside temperatures as part of the vent

system. The damper should be on the cold air side of the thermal

break.

The break should be as close as possible to where the vent

system enters the heated portion of the house.

Makeup Air

Local building codes may require the use of makeup air systems

when using ventilation systems greater than specified CFM of air

movement. The specified CFM varies from locale to locale.

Consult your HVAC professional for specific requirements in your

area.

Venting Methods

This island hood is factory set for venting through the roof.

An 6" (15.2 cm) round vent system is needed for installation (not

included). The hood exhaust opening is 6" (15.2 cm) round.

NOTE: Flexible vent is not recommended. Flexible vent creates

back pressure and air turbulence that greatly reduce

performance.

Vent system can terminate either through the roof or wall. To vent

through a wall, a 90° elbow is needed.

A. Ceiling height

B. Hood height from ceiling to bottom of the

range hood: A - C - D = B

C. 24" (61.0 cm) minimum to 36" (91.4 cm)

maximum suggested hood height

D. Countertop height

Vented Installations

Min. ceiling height Max. ceiling height

Electric cooking

surface

7' 9" (2.36 m) 9' 10" (3.0 m)

Gas cooking

surface

8' (2.44 m) 9' 10" (3.0 m)

Non-Vented (Recirculating) Installations

Min. ceiling height Max. ceiling height

Electric cooking

surface

7' 9" (2.36 m) 10' 4" (3.15 m)

Gas cooking

surface

8' (2.44 m) 10' 4" (3.15 m)

C A

For Non-Vented (recirculating) Installations

If it is not possible to vent cooking fumes and vapors to the

outside, the hood can be used in the non-vented (recirculating)

version, fitting a charcoal filter and the deflector. Fumes and

vapors are recycled through the top grille.

NOTE: Wall venting can be an option for 2-story homes.

Calculating Vent System Length

To calculate the length of the system you need, add the

equivalent feet (meters) for each vent piece used in the system.

Maximum equivalent vent length is 35 ft (10.7 m).

Example Vent System

The following example falls within the maximum vent length of

35 ft (10.7 m).

Electrical Requirements

Observe all governing codes and ordinances.

Ensure that the electrical installation is adequate and in

conformance with National Electrical Code, ANSI/NFPA 70 (latest

edition), or CSA Standards C22.1-94, Canadian Electrical Code,

Part 1 and C22.2 No. 0-M91 (latest edition) and all local codes

and ordinances.

If codes permit and a separate ground wire is used, it is

recommended that a qualified electrician determine that the

ground path is adequate.

A copy of the above code standards can be obtained from:

National Fire Protection Association

1 Batterymarch Park

Quincy, MA 02169-7471

CSA International

8501 East Pleasant Valley Road

Cleveland, OH 44131-5575

■ A 120 volt, 60 Hz., AC only, 15-amp, fused electrical circuit is

required.

■ If the house has aluminum wiring, follow the procedure

below:

1. Connect a section of solid copper wire to the pigtail

leads.

2. Connect the aluminum wiring to the added section of

copper wire using special connectors and/or tools

designed and UL listed for joining copper to aluminum.

Follow the electrical connector manufacturer's recommended

procedure. Aluminum/copper connection must conform with

local codes and industry accepted wiring practices.

■ Wire sizes and connections must conform with the rating of

the appliance as specified on the model/serial/rating plate.

The model/serial/rating plate is located behind the left filter

on the rear wall of the range hood.

■ Wire sizes must conform to the requirements of the National

Electrical Code, ANSI/NFPA 70 (latest edition), or CSA

Standards C22. 1-94, Canadian Electrical Code, Part 1 and

C22.2 No. 0-M91 (latest edition) and all local codes and

ordinances.

Roof venting Non-vented (recirculating)

A. Roof cap

B. 6" (15.2 cm) round vent

A. Deflector

B. 6" (15.2 cm) round vent

Vent piece 6" (15.2 cm) round

45° elbow 2.5 ft

(0.8 m)

90° elbow 5.0 ft

(1.5 m)

1 - 90° elbow = 5.0 ft (1.5 m)

1 - wall cap = 0.0 ft (0.0 m)

8 ft (2.4 m) straight = 8.0 ft (2.4 m)

System length = 13 ft (3.9 m)

90 elbow

6 ft (1.8 m)

2 ft

(0.6 m)

Wall cap

INSTALLATION INSTRUCTIONS

Prepare Location

■ It is recommended that the vent system be installed before

the range hood is installed.

■ Before making cutouts, make sure there is proper clearance

within the ceiling for exhaust vent.

■ Range hood is to be installed 24" (61.0 cm) min. for electric

cooking surfaces, or 27" (68.6 cm) min. for gas cooking

surfaces, to suggested maximum of 36" (91.2 cm) above the

cooking surface.

■ Check your ceiling height and the range hood height

maximum before you select your hood.

1. Disconnect power.

2. Determine which venting method to use: roof, or non-vented.

3. Select a flat surface for assembling the range hood. Place

covering over that surface.

4. Using 2 or more people, lift range hood onto covered surface.

Range Hood Mounting Screws Installation

1. Determine and mark the centerline on the ceiling where the

range hood will be installed, after considering the

requirements for ceiling support structures. See the “Location

Requirements” section. Make sure the range hood is

centered over the cooking surface.

2. Tape template in place on the ceiling at the marked

centerline. The line for the front of the range hood should be

parallel to the front of the cooktop.

3. Use a pencil to mark the mounting screws, wire access and

duct hole locations on the ceiling.

NOTE: Mounting hole locations should be into a ceiling

support structure capable of holding 100 lbs (45.4 kg).

Remove the template.

4. Drill 4 - ³⁄₁₆" (4.8 mm) pilot holes for mounting the upper

horizontal support.

Complete Preparation

1. Determine the required location for the home power supply

cable and drill a ½" (1.3 cm) diameter hole for wire access.

2. Run wire through the home power supply cable according to

the National Electrical Code or CSA Standards and local

codes and ordinances. There must be enough ½" conduit

and wires from the fused disconnect (or circuit breaker) box

to make the connection in the hood’s electrical terminal box.

NOTE: Do not reconnect power until installation is complete.

3. For vented installations only: Using a jigsaw or keyhole

saw, cut a 6½" (16.5 cm) diameter hole for the vent duct.

Attach the upper horizontal support bracket with 4 - 5 x 45 mm

wood screws.

IMPORTANT: All screws must be installed into wood. If there

is no wood to screw into, additional wall framing supports

may be required.The ceiling support structure must be

capable of holding 100 lbs (45.4 kg).

Install In-Line Smart Kit - Optional

NOTE: Your range hood can work with either an internal or an in-

line (external) blower motor system. An optional In-Line Smart Kit

(purchased separately) allows the blower motor that comes with

this range hood to be installed in a location other than inside the

range hood cavity.

CAUTION: To reduce the risk of fire and electric shock, install this

range hood only with the In-Line Smart Kit manufactured by

Whirlpool, Part Number W10692945.

For installation see the In-Line Smart Kit installation instructions.

See the “Assistance or Service” section to order.

Assemble and Install Range Hood

1. Install transition on top of hood (if removed for shipping) with

2 - 3.5 x 9.5 mm sheet metal screws.

WARNING

Excessive Weight Hazard

Use two or more people to move and install

range hood.

Failure to do so can result in back or other injury.

A. Upper horizontal support

A. Vent transition

B. 3.5 x 9.5 mm screw

2. Position the 4 vertical supports (A) with notches at the bottom

and attach to the range hood using 16 - 4.2 x 8 mm screws.

3. Attach the horizontal support (B) using 8 - 4.2 x 8 mm screws.

4. Attach a second set of vertical supports (A) and set the

vertical height (B). See “Installation Dimensions” in the

“Location Requirements” section to help determine the

desired dimension for the vertical height (B). Secure with

16 - 4.2 x 8 mm T20

screws.

5. Using 2 or more people, lift the range hood assembly and

attach it by snapping the vertical supports to the spring clips

in the upper horizontal support bracket that is mounted to the

ceiling.

NOTE: The range hood assembly must be held in place while

installing the screws in the next step.

6. Install 16 - 4.2 x 8 mm screws and tighten to secure.

Connect Vent System

1. Install vent system.

2. Push duct over the exhaust outlet. Seal all connections with

vent clamps.

3. Use caulk to seal all openings.

Non-Vented (Recirculating) Installation

1. Attach the air deflector to the upper horizontal support using

4 mounting screws.

2. Measure the length of 6" (15.2 cm) duct needed to connect

the transition to the deflector.

NOTE: Vent should fit up inside the deflector 1" (2.5 cm)

minimum.

3. Install vent between the transition and the deflector.

NOTE: To make vent installation easier, temporarily remove

the deflector from the chimney support bracket and replace

after vent section is in place.

4. Seal all connections with vent clamps.

Make Electrical Connection

1. Disconnect power.

2. Remove terminal box cover.

3. Remove the knockout in the terminal box, and then install a

UL listed or CSA approved ¹⁄₂" (12.7 mm) strain relief.

A. Vertical supports

B. Horizontal support

A. Vertical supports

B. Vertical height

A. Mounting screws

A. Deflector

B. Mounting screws

A. Knockout

B. Terminal box

C. Terminal box cover

WARNING

Electrical Shock Hazard

Disconnect power before servicing.

Replace all parts and panels before operating.

Failure to do so can result in death or electrical shock.

4. Run home power supply cable through strain relief and into

the terminal box.

5. Use UL listed wire connectors and connect black wires (C)

together.

6. Use UL listed wire connectors and connect white wires (E)

together.

7. Connect green (or bare) ground wire from home power supply

to yellow-green ground wire (F) in terminal box using UL listed

wire connectors.

8. Tighten strain relief screw.

9. Install terminal box cover.

10. Check that all light bulbs are secure in their sockets.

11. Reconnect power.

Optional Power Cord Kit Installations

For optional power cord kit installations, follow the instructions

supplied with the power cord kit. See the “Assistance or Service”

section for information on ordering.

NOTE: Use only with range hood cord connection kits that have

been investigated and found acceptable for use with this model

range hood.

Install Duct Covers

NOTE: Remove the film from the duct covers.

1. Assemble the upper duct covers together, and then install the

duct covers around the support frame. The larger hole in the

flanges of the upper duct cover must be outside the smaller

hole in the mating flange of the other upper duct cover.

2. Secure the upper duct covers together with two 3.5 x 6.5 mm

screws at the top and two 2.9 x 3 mm screws at the bottom.

Install 1 screw on each side at the top and bottom of the

assembled duct covers.

NOTE: For non-vented (recirculating) installation, the slotted

holes in the upper duct covers will be visible when assembled.

For vented installations, the slotted holes will be hidden down

inside the lower duct covers.

A. Home power supply cable

B. UL listed or CSA approved

strain relief

C. Black wires

D. UL listed wire connectors

E. White wires

F. Green (or bare) and yellow-

green ground wires

WARNING

Electrical Shock Hazard

Electrically ground blower.

Connect ground wire to green and yellow ground wire

in terminal box.

Failure to do so can result in death or electrical shock.

A. 3.5 x 6.5 mm screws (2)

B. Assembly holes (larger hole outside of

smaller hole on both sides)

C. 2.9 x 3 mm screws (2)

A. Top toward ceiling

B. Slots installed up for non-vented installations

C. Slots installed down for vented installations

3. Slide the upper duct covers up the frame to the ceiling, and

then secure to the upper horizontal support with 2 - 3.5 x 6.5

mm screws.

4. Place the long end of the plastic clips (2) into the bottom of

the front lower duct cover.

5. Install the lower duct cover (front) to the range hood canopy.

Spread the lower duct cover opening slightly and position it

over the upper duct cover. Set the lower duct cover in place.

Position so the flanges of the lower duct cover set into the

flanges of the upper duct covers.

6. Install the lower duct cover (rear) to the range hood canopy.

Spread the lower duct cover opening slightly and position it

over the upper duct cover. Set the lower duct cover in place.

Position so the flanges of the lower duct cover set into the

flanges of the upper duct cover. Make sure the front and rear

lower duct covers mate properly.

NOTE: When assembling the rear lower duct cover to the front

lower duct cover, the flange (both sides) must be placed over the

plastic clip to secure the lower duct covers together at the

bottom.

7. Secure the lower duct covers together at the top using

plastic clips (2). Use one plastic clip on each side.

8. Secure the lower duct cover to the range hood canopy using

4 - 4.2 x 8 mm screws.

Complete Installation

1. For non-vented (recirculating) installations only, install

charcoal filters onto the metal filters. See the “Range Hood

Care” section.

2. Install metal filters. See the “Range Hood Care” section.

3. Check the operation of the range hood blower and light. See

the “Range Hood Use” section.

If range hood does not operate, check to see whether a

circuit breaker has tripped or a household fuse has blown.

NOTE: To get the most efficient use from your new range hood,

read the “Range Hood Use” section.

A. 3.5 x 6.5 mm screw

B. Slotted holes (2)

C. Upper duct covers

D. Ceiling

A. Lower duct cover - (front)

B. Plastic clips (2) (long end for front placement)

A. Range hood canopy

B. Plastic clips

C. Lower duct covers

D. Upper duct covers

A. Lower duct cover (rear)

B. Plastic clips

C. Lower duct covers

D. Upper duct covers

A. Plastic clips (2)

B. Lower duct covers top clip area

RANGE HOOD USE

The range hood is designed to remove smoke, cooking vapors

and odors from the cooktop area. For best results, start the hood

before cooking and allow it to operate several minutes after the

cooking is complete to clear all smoke and odors from the

kitchen.

The range hood controls are located on the front side of the

canopy.

Control Panel

Controls and Features

NOTES:

■ To activate the controls, press and release the desired button.

■ The control feature button will be lit when a control feature is

turned On.

Sleep Mode

The range hood automatically enters Sleep Mode when not in

use. After 10 minutes of no range hood activity, all of the control

button lights will turn Off. To deactivate Sleep Mode, press any

button.

Auto Sense

Auto Sense allows the range hood fan to turn on automatically

when it senses heat higher than its allowable temperature limit.

When Auto Sense is On, the fan speed will increase or decrease

based on the temperature Auto Sense is measuring.

Auto Sense can be manually increased by pressing a higher fan

speed. The fan will run at the selected speed for 10 minutes

before returning to the speed selected for Auto Sense.

If Auto Sense is On, the Auto button light will turn Off and go into

Sleep Mode when the vent hood is not in use. If the vent hood is

turned On by the consumer or by Auto Sense, the Auto button

light will turn On.

To set Auto Sense:

Press AUTO.

To Select Auto Sense Cooktop Type:

NOTE: The range hood is factory-set for the gas cooktop

mode.

Press and hold AUTO for 5 seconds to switch between the

gas cooktop and electric cooktop modes.

The Auto button light will flash 5 times when the range hood

is changed to the electric cooktop mode. Auto Sense is now

set to work with electric cooktops and ranges.

The Auto button light will flash 3 times when the range hood

is changed to the gas cooktop mode. Auto Sense is now set

to work with gas cooktops and ranges.

Changing the cooktop type will change the temperature limit

for Auto Sense to turn On. When the range hood senses a

high enough temperature, the fan will start automatically.

When the temperature drops below the set temperature limit,

the fan will stop automatically. The Auto button light will turn

Off after the range hood enters Sleep Mode, but Auto Sense

is still active.

To Deactivate Auto Sense:

If the Auto button is lit, press AUTO once to deactivate Auto

Sense. The Auto button light will turn Off.

If Auto Sense is in Sleep Mode, press AUTO once to

deactivate Sleep Mode and turn the Auto button light On.

Press AUTO again to deactivate Auto Sense and turn Off the

Auto button light.

Auto Sense will automatically turn off after 2 hours of no

activation of the Auto Sense system. To reset Auto Sense,

press AUTO.

Manual Vent Functions

A. Louver holes (non-vented

[recirculating] installations only)

B. Upper duct covers

C. Lower duct covers

D. LED lights (4)

E. Metal grease filters

(located behind the

perimetic cover)

F. P e ri m et i c c o v e r

G. Canopy

H. Control panel

Fan Speeds

Low Press LOW to turn the fan on at Low speed.

Med Press MED to turn the fan on at Medium

speed.

Hi Press HI to turn the fan on at High speed.

Boost Press BOOST to turn the fan on at the highest

speed. Boost will automatically turn Off after

10 minutes and the fan will switch to High

speed.

Timer

The range hood can be set to turn Off automatically after

15 minutes.

1. Press and hold the desired fan speed button for 2 seconds.

The fan will run on the chosen speed for 15 minutes, and the

fan speed button light will flash continuously.

After 15 minutes, the fan will turn Off automatically.

2. Press the desired fan speed button again while the fan timer

is running to cancel the fan timer.

NOTE: Changing the fan speed or turning Auto Sense On will

also cancel the 15-minute timer.

Light

The range hood has both task and ambient lighting.

To operate the lights:

1. Touch LIGHT once to turn the LED task lights On.

2. Touch LIGHT again to turn LED task lights Off. The ambient

lights will turn On.

3. Touch LIGHT a third time to turn the ambient lights Off.

NOTE: To turn both the task and ambient lights on at the same

time, touch and hold LIGHT for 2 seconds. Touch LIGHT again to

turn the task and ambient lights Off.

RANGE HOOD CARE

Cleaning

IMPORTANT: Clean the hood and grease filters frequently

according to the following instructions. Replace grease filters

before operating hood.

Exterior Surfaces:

To avoid damage to the exterior surface, do not use steel wool or

soap-filled scouring pads.

Always wipe dry to avoid water marks.

Cleaning Method:

■ Liquid detergent soap and water, or all-purpose cleanser

■ Wipe with damp soft cloth or nonabrasive sponge, and then

rinse with clean water and wipe dry.

Metal Grease Filter

1. Open the stainless steel panel. Grasp panel at the front

corners and pull down to disengage the 2 catch pins from the

spring catches. The panel is attached at the rear and will

rotate down.

2. Remove each filter by pulling the spring release handle and

then pulling down the filter.

3. Wash metal filters as needed in dishwasher or hot detergent

solution.

4. Reinstall the filter by making sure the spring release handles

are toward the front. Insert aluminum filter into upper track.

5. Push in spring release handle.

6. Push up on metal filter and release handle to latch into place.

7. Repeat steps 1 through 5 for the other filter.

8. Close the stainless steel panel. Engage the (2) pins in the

spring catches to secure.

Non-Vented (Recirculating) Installation Filters

The charcoal filter is not washable. It should last up to 6 months

with normal use. Replace with Charcoal Filter Kit. See the

“Accessories” section for information on ordering.

To replace charcoal filter:

1. Remove metal grease filter from range hood. See “Metal

Grease Filter” in this section.

2. Bend spring clips away from metal grease filter.

3. Place charcoal filter into top side of metal filter.

A. Metal filters

B. Stainless steel panel

C. Catch pins (2)

D. Spring catches (2)

A. Spring release handle

4. Bend spring clips back into place to secure the charcoal filter

to the metal filter.

5. Replace metal grease filter. See “Metal Grease Filter” in this

section.

6. Turn the charcoal filter clockwise to lock it.

7. Repeat steps 1 and 2 on the other filter.

Replacing an LED Lamp

The LED lights are replaceable by a service technician only. See

the Warranty for service contact information.

WIRING DIAGRAM

Motor Specifications

Power Supply

Frequency

Power Absorbtion

120 VAC

60 HZ

420 W

Motor Resistance ( )

Blue-Black

Blue-Grey

Blue-Red

Blue-White

9.8

14.3

21.6

SE130B

YL/GN

Auto-Speed

Sensor

User Interface

LED

Strip LED

LED

YL/GN

GND

YL/GN

EMI

Filter

La2

GND

PWM

RL1

RL2

RL5

La1

Electronic Power Board

RL4

RL3

Driver

Input: 120VAC

Output: 700mA (2-15VDC)

Driver

Input: 120VAC

Output: 700mA (2-15VDC)

ASSISTANCE OR SERVICE

If you need service

Please refer to the warranty page in this manual.

If you need replacement parts

If you need to order replacement parts, we recommend that you

use only factory specified parts. Factory specified parts will fit

right and work right because they are made with the same

precision used to build every new appliance.

To locate factory specified replacement parts in your area, call

the following customer assistance telephone number or your

nearest designated service center.

In the U.S.A.

Call Jenn-Air Customer eXperience Center toll free:

1-800-JENNAIR (1-800-536-6247) or visit our website at

www.jennair.com.

Our consultants provide assistance with:

■ Scheduling of service. Jenn-Air

appliances designated

service technicians are trained to fulfill the product warranty

and provide after-warranty service anywhere in the United

States.

■ Features and specifications on our full line of appliances.

■ Referrals to local Jenn-Air

appliance dealers.

■ Installation information.

■ Use and maintenance procedures.

■ Accessory and repair parts sales.

■ Specialized customer assistance (Spanish speaking, hearing

impaired, limited vision, etc.).

For further assistance

If you need further assistance, you can write to Jenn-Air

Appliances with any questions or concerns at:

Jenn-Air Brand Home Appliances

Customer eXperience Center

553 Benson Road

Benton Harbor, MI 49022-2692

Please include a daytime phone number in your correspondence.

In Canada

Call the Whirlpool Canada LP Customer eXperience Centre toll

free at 1-800-JENNAIR (1-800-536-6247) or visit our website at

www.jennair.ca.

Our consultants provide assistance with:

■ Scheduling of service. Jenn-Air

appliances designated

service technicians are trained to fulfill the product warranty

and provide after-warranty service anywhere in the Canada.

■ Features and specifications on our full line of appliances.

■ Referrals to local Jenn-Air

appliance dealers.

■ Installation information.

■ Use and maintenance procedures.

■ Accessory and repair parts sales.

For further assistance

If you need further assistance, you can write to Jenn-Air

Appliances with any questions or concerns at:

Jenn-Air Brand Home Appliances

Customer eXperience Centre

200 - 6750 Century Ave.

Mississauga, Ontario L5N 0B7

Please include a daytime phone number in your correspondence.

Accessories

Charcoal Filter Kit

(for non-vented installations only)

Order Part Number W10690910

Recirculation Kit

(for non-vented installations only)

Order Part Number W10692909

Chimney Extension Kit

Order Part Number W10688278

6" (15.2 cm) Makeup Air Kit

(consult local building codes)

Order Part Number W10446915

Power Cord Kit

Order Part Number W10613691

In-Line Smart Kit

Order part Number W10692945

12/14

JENN-AIR

MAJOR APPLIANCE

LIMITED WARRANTY

ATTACH YOUR RECEIPT HERE. PROOF OF PURCHASE IS REQUIRED

TO OBTAIN WARRANTY SERVICE.

Please have the following information available when you call the

Customer eXperience Center:

■ Name, address and telephone number

■ Model number and serial number

■ A clear, detailed description of the problem

■ Proof of purchase including dealer or retailer name and address

IF YOU NEED SERVICE:

1. Before contacting us to arrange service, please determine whether your product requires repair. Some

questions can be addressed without service. Please take a few minutes to review the Troubleshooting or

Problem Solver section of the Use and Care Guide, scan the QR code on the right to access additional

resources, or visit https://jennair.custhelp.com.

2. All warranty service is provided exclusively by our authorized Jenn-Air Service Providers

. In the U.S. and

Canada, direct all requests for warranty service to:

Jenn-Air Customer eXperience Center

1-800-JENNAIR (1-800-536-6247)

If outside the 50 United States or Canada, contact your authorized Jenn-Air dealer to determine whether another warranty applies.

https://jennair.custhelp.com

TWO YEAR LIMITED WARRANTY

WHAT IS COVERED WHAT IS NOT COVERED

For two years from the date of purchase, when this

major appliance is installed, operated and maintained

according to instructions attached to or furnished with

the product, Jenn-Air brand of Whirlpool Corporation or

Whirlpool Canada LP (hereafter “Jenn-Air”) will pay for

Factory Specified Replacement Parts and repair labor

to correct defects in materials or workmanship that

existed when this major appliance was purchased, or at

its sole discretion replace the product. In the event of

product replacement, your appliance will be warranted

for the remaining term of the original unit's warranty

period.

YOUR SOLE AND EXCLUSIVE REMEDY UNDER THIS

LIMITED WARRANTY SHALL BE PRODUCT REPAIR

AS PROVIDED HEREIN. Service must be provided by a

Jenn-Air designated service company. This limited

warranty is valid only in the United States or Canada

and applies only when the major appliance is used in

the country in which it was purchased. This limited

warranty is effective from the date of original consumer

purchase. Proof of original purchase date is required to

obtain service under this limited warranty.

1. Commercial, non-residential, multiple-family use, or use inconsistent with published

user, operator or installation instructions.

2. In-home instruction on how to use your product.

3. Service to correct improper product maintenance or installation, installation not in

accordance with electrical or plumbing codes or correction of household electrical or

plumbing (i.e. house wiring, fuses or water inlet hoses).

4. Consumable parts (i.e. light bulbs, batteries, air or water filters, preservation

solutions, etc.).

5. Defects or damage caused by the use of non-genuine Jenn-Air parts or accessories.

6. Conversion of products from natural gas or L.P. gas.

7. Damage from accident, misuse, abuse, fire, floods, acts of God or use with products

not approved by Jenn-Air.

8. Repairs to parts or systems to correct product damage or defects caused by

unauthorized service, alteration or modification of the appliance.

9. Cosmetic damage including scratches, dents, chips, and other damage to the

appliance finishes unless such damage results from defects in materials and

workmanship and is reported to Jenn-Air within 30 days.

10. Discoloration, rust or oxidation of surfaces resulting from caustic or corrosive

environments including but not limited to high salt concentrations, high moisture or

humidity or exposure to chemicals.

11. Food or medicine loss due to product failure.

12. Pick-up or delivery. This product is intended for in-home repair.

13. Travel or transportation expenses for service in remote locations where an authorized

Jenn-Air servicer is not available.

14. Removal or reinstallation of inaccessible appliances or built-in fixtures (i.e. trim,

decorative panels, flooring, cabinetry, islands, countertops, drywall, etc.) that

interfere with servicing, removal or replacement of the product.

15. Service or parts for appliances with original model/serial numbers removed, altered

or not easily determined.

The cost of repair or replacement under these excluded circumstances shall be

borne by the customer.

DISCLAIMER OF IMPLIED WARRANTIES

IMPLIED WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR IMPLIED WARRANTY OF FITNESS FOR A

PARTICULAR PURPOSE, ARE LIMITED TO ONE YEAR OR THE SHORTEST PERIOD ALLOWED BY LAW. Some states and provinces do not allow

limitations on the duration of implied warranties of merchantability or fitness, so this limitation may not apply to you. This warranty gives you specific

legal rights, and you also may have other rights that vary from state to state or province to province.

DISCLAIMER OF REPRESENTATIONS OUTSIDE OF WARRANTY

Jenn-Air makes no representations about the quality, durability, or need for service or repair of this major appliance other than the representations

contained in this warranty. If you want a longer or more comprehensive warranty than the limited warranty that comes with this major appliance, you

should ask Jenn-Air or your retailer about buying an extended warranty.

LIMITATION OF REMEDIES; EXCLUSION OF INCIDENTAL AND CONSEQUENTIAL DAMAGES

YOUR SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT REPAIR AS PROVIDED HEREIN. JENN-AIR

SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. Some states and provinces do not allow the exclusion or limitation of

incidental or consequential damages, so these limitations and exclusions may not apply to you. This warranty gives you specific legal rights, and

you also may have other rights that vary from state to state or province to province.

W10674115D

3/15

Printed in Mexico

Imprimé au Mexique

Jenn-Air JXI8536DS0 Owner's manual

Brand: Jenn-Air

Model: JXI8536DS0

Category: Cooker hoods

Type: Owner's manual

Download PDF

report

Jenn-Air JXI8536DS0 Owner's manual

Jenn-Air JXI8536DS0 Owner's manual

Related papers

Other documents