Whirlpool WOC75EC0HS02 Installation guide

INSTALLATION INSTRUCTIONS

27" (68.6 CM) AND 30" (76.2 CM) ELECTRIC BUILT-IN

MICROWAVE/OVEN COMBINATION

INSTRUCTIONS D’INSTALLATION

FOUR CONVENTIONNEL ET FOUR À MICRO-ONDES

ÉLECTRIQUES, COMBINÉS ET ENCASTRÉS

DE 27" (68,6 CM) ET 30" (76,2 CM)

INSTRUCCIONES DE INSTALACIÓN DE LA COMBINACIÓN

DE HORNO/MICROONDAS EMPOTRADO ELÉCTRICO DE

27" (68,6 CM) Y 30" (76,2CM)

Table of Contents

BUILT-IN MICROWAVE/OVEN COMBINATION SAFETY ......... 2

INSTALLATION REQUIREMENTS

............................................... 2

Tools and Parts

............................................................................. 2

Built-In Microwave/Oven Combination

Lo

cation Requirements ................................................................3

Electrical Requirements ...............................................................4

INSTALLATION INSTRUCTIONS

................................................. 5

Prepare Built-In Oven

...................................................................5

SÉCURITÉ DU FOUR À MICRO-ONDES ET DU FOUR

CONVENTIONNEL COMBINÉS ET ENCASTRÉS

....................11

EXIGENCES D’INSTALLATION

..................................................11

Outils et pièces

...........................................................................11

Exigences d’emplacement de l’ensemble four

à micro-ondes et four conventionnel encastrés ........................11

Spéciﬁcations électriques

..........................................................13

INSTRUCTIONS D’INSTALLATION

...........................................14

Préparation du four encastré

.....................................................14

Table des matières

Remove Oven Door(s) ..................................................................5

Replace Oven Door(s)

..................................................................6

Make Electrical Connection

.........................................................7

Install Oven

................................................................................... 8

Install Warming Drawer Deﬂector Kit

..........................................9

Complete Installation

.................................................................10

Dépose de la/des porte(s) du four .............................................14

Réinstallation de la porte(s) du four

...........................................15

Raccordement électrique

...........................................................16

Installation du four

......................................................................17

Installation de l’ensemble déﬂecteur du

tiroir-réchaud (uniquement pour les fours

installés au-dessus d'un tiroir-réchaud)

.....................................18

Achever l’installation

..................................................................19

Índice

SEGURIDAD DE LA COMBINACION DE HORNO

DE MICROONDAS/HORNO INTEGRADO ................................20

REQUISITOS DE INSTALACIÓN

................................................20

Herramientas y piezas

................................................................20

Requisitos de ubicación de la combinación de horno de

microondas/horno integrados

...................................................20

Requisitos eléctricos

..................................................................22

INSTRUCCIONES DE INSTALACIÓN

.......................................23

Preparación del horno empotrado

.............................................23

Retire la puerta del horno

...........................................................23

Vuelva a colocar la puerta del horno

.........................................24

Haga la conexión del suministro eléctrico

.................................25

Instale el horno

...........................................................................26

Instale el kit de deﬂector para cajón de calentamiento (para

hornos instalados encima de un cajón de calentamiento)

........27

Completar la instalación

............................................................28

IMPORTANT:

Save for local electrical inspector’s use.

IMPORTANT :

À conserver pour consultation par l’inspecteur local des installations électriques.

IMPORTANTE:

Guarde para tener a disposición del inspector de electricidad local.

W11129957A

2

BUILT-IN MICROWAVE/OVEN COMBINATION SAFETY

INSTALLATION REQUIREMENTS

Tools and Parts

Gather the required tools and parts before starting installation.

Read and follow the instructions provided with any tools listed

here.

Tools Needed

■ Phillips screwdriver

■ Measuring tape

■ Drill (for wall cabinet installations)

■ 1” (2.5 cm) drill bit (for wall cabinet installations)

■ Level

■ Flat-blade screwdriver

Parts Needed

■ UL listed or CSA Approved conduit connector

■ UL listed wire connectors

■ Warming Drawer Deﬂector Kit (for ovens installed above a

warming drawer):

Color Size Type Warming Drawer

Deﬂector Kit

White 27” Combo W10510613

White 30” Combo W10510614

Black 27” Combo W10531009

Black 30” Combo W10531010

Stainless Steel 27” Combo W10536338

Stainless Steel 30” Combo W10536339

Black Stainless

Steel

27” Combo W10888988

Black Stainless

Steel

30” Combo W10727416

Bronze 30” Combo W11123007

To order, see the “Assistance or Service” section of the Use and

Care Guide.

■ Flush Installation Kit (for Single and Double installed at ﬂush

installation):

Color Size Type Flush Installation

Kit

White 27” Combo W11173682

White 30” Combo W11173684

Black 27” Combo W11173686

Black 30” Combo W11173692

Stainless Steel 27” Combo W11173695

Stainless Steel 30” Combo W11123004

Black Stainless

Steel

27” Combo W11173701

Black Stainless

Steel

30” Combo W11173704

Bronze 30” Combo W11123006

To order, see the “Assistance or Service” section of the Use and

Care Guide.

Parts Supplied

■ Four #8–14 x 3/4” (19 mm) screws

■ Bottom vent

■ Two #8–18 x 3/8” (9.5 mm) screws — bottom vent

Check local codes. Check existing electrical supply. See the

“Electrical Requirements” section.

It is required that all electrical connections be made by a

licensed, qualiﬁed electrical installer.

You can be killed or seriously injured if you don't immediately

You

can be killed or seriously injured if you don't

follow

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can

happen if the instructions are not followed.

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.”

These words mean:

follow instructions.

instructions.

DANGER

WARNING

3

Built-In Microwave/Oven Combination

Location Requirements

IMPORTANT: Observe all governing codes and ordinances.

■ Cabinet opening dimensions that are shown must be used.

Given dimensions provide minimum clearance with oven.

■ Recessed installation area must provide complete enclosure

around the recessed portion of the oven.

■ Grounded electrical supply is required. See the “Electrical

Requirements” section.

■ Electrical supply junction box should be located 3” (7.6 cm)

above the cutout 3” (7.6 cm) maximum below the support

surface when the oven is installed in a wall cabinet. A 1” (2.5

cm) minimum diameter hole should have been drilled in the

right rear or left rear corner of the upper or lower support

surface to pass the appliance cable through to the junction

box.

■ Oven support surface must be solid, level and ﬂush with

bottom of cabinet cutout. Floor must be able to support a

total weight (microwave and built-in oven) of 208 lbs (95 kg)

for 27” (68.6 cm) models or 249 lbs (113 kg) for 30” (76.2 cm)

models.

IMPORTANT: To avoid damage to your cabinets, check

with your builder or cabinet supplier to make sure that the

materials used will not discolor, delaminate or sustain other

damage. This oven has been designed in accordance with

the requirements of UL and CSA International and complies

with the maximum allowable wood cabinet temperatures of

194°F (90°C).

Product Dimensions

27” (68.6 cm) and 30” (76.2 cm) Ovens

Cabinet Dimensions

27” (68.6 cm) and 30” (76.2 cm) Ovens

27" (68.6 cm) models

A. 42

9

⁄

16

" (108.0 cm) overall height

B. 25

7

⁄

16

" (64.6 cm) recessed width

C. 41" (104.1 cm) recessed height

D. 23¹⁄

4

" (59.1 cm) max. recessed

depth

E. 27" (68.6 cm) overall width

F. 48" (121.9 cm) Flexible conduit

length measured from the

conduit clamp located at the

rear of the oven. Do not remove

the conduit clamp.

30" (76.2 cm) models

A. 42

9

⁄

16

" (108.0 cm) overall height

B. 28¹⁄

2

" (72.3 cm) recessed width

C. 41" (104.1 cm) recessed height

D. 23¹⁄

4

" (59.1 cm) max. recessed

depth

E. 30" (76.2 cm) overall width

F. 48" (121.9 cm) Flexible conduit

length measured from the

conduit clamp located at the

r

ear of the oven. Do not remove

the conduit clamp.

* NOTE: The cutout height can be between 41" (104.1 cm) and

41½" (105.6 cm) for microwave/oven combination.

F

E

A

D

G

B

C

27" (68.6 cm) model

s

A.

27" (68.6 cm) min. cabinet

width

B.

1" (2.5 cm) top of cutout to

bottom of upper cabinet door

C.

19¹⁄

4

" (48.9 cm) bottom of

cutout to ﬂoor is

r

ecommended.

4"-19¹⁄

4

" (10.2-48.9 cm) bottom

of cutout to ﬂoor is acceptable.

D.

25¹⁄

2

" (64.8 cm) cutout width

E.

1¹⁄

2

" (3.8 cm) min. bottom of

cutout to top of cabinet door

F.

41

5

⁄

16

" (105 cm)* recommended

cutout height

G.

24" (60.7 cm) cutout depth

30" (76.2 cm) models

A. 30" (76.2 cm) min. cabinet

width

B. 1" (2.5 cm) top of cutout to

bottom of upper cabinet door

C. 19¹⁄

4

" (48.9 cm) bottom of

cutout to ﬂoor is

recommended.

4"-19¹⁄

4

" (10.2-48.9 cm) bottom

of cutout to ﬂoor is acceptable.

D. 28¹⁄

2

" (72.4 cm) cutout width

E. 1¹⁄

2

" (3.8 cm) min. bottom of

cutout to top of cabinet door

F. 41

5

⁄

16

" (105 cm)* recommended

cutout height

G. 24" (60.7 cm) cutout depth

4

Electrical Requirements

If codes permit and a separate ground wire is used, it is

recommended that a qualiﬁed electrical installer determine that

the ground path and wire gauge are in accordance with local

codes.

Check with a qualiﬁed electrical installer if you are not sure the

oven is properly grounded.

This oven must be connected to a grounded metal, permanent

wiring system.

Be sure that the electrical connection and wire size are adequate

and in conformance with the National Electrical Code, ANSI/

NFPA 70-latest edition or CSA Standards C22.1-94, Canadian

Electrical Code, Part 1 and C22.2 No. O-M91-latest edition, and

all local codes and ordinances.

A copy of the above code standards can be obtained from:

National Fire Protection Association

1 Batterymarch Park

Quincy, MA 02169-7471

CSA International

8501 East Pleasant Valley Road

Cleveland, OH 44131-5575

Electrical Connection

To properly install your oven, you must determine the type of

electrical connection you will be using and follow the instructions

provided for it here.

■ Oven must be connected to the proper electrical voltage,

amperage, and frequency as speciﬁed on the model/serial/

rating plate. See the following illustration.

■ Models rated from 7.3 to 9.6 kW at 240 volts (6.3 to 8.3 kW

at 208 volts) require a separate 40-amp circuit. Models

rated from 4.9 to 7.2 kW at 240 volts (4.3 to 6.2 kW at

208 volts) require a separate 30-amp circuit. Models rated at

4.8 kW and below at 240 volts (4.2 kW and below at

208 volts) require a separate 20-amp circuit.

■ A circuit breaker is recommended.

■ Connect directly to the fused disconnect (or circuit breaker

box) through ﬂexible, armored or nonmetallic sheathed,

copper cable (with grounding wire). See the “Make Electrical

Connection” section.

■ Flexible conduit from the oven should be connected directly

to the junction box.

■ Do not cut the conduit. The length of conduit provided is for

serviceability of the oven.

■ A UL Listed or CSA Approved conduit connector must be

provided.

■ If the house has aluminum wiring, follow the procedure

below:

■ Connect the aluminum wiring using special connectors

and/or tools designed and UL Listed for joining copper to

aluminum.

Follow the electrical connector manufacturer’s recommended

procedure. Aluminum/copper connection must conform with

local codes and industry accepted wiring practices.

Be sure that the electrical connection and wire size are

adequate and in conformance with the National Electrical

Code, ANSI/ NFPA 70-latest edition or CSA Standards

C22.1-94, Canadian Electrical Code, Part 1and C22.2 No.

O-M91-latest edition, and all local codes and ordinances.

A copy of the above code standards can be obtained

from: National Fire Protection Association 1 Batterymarch

Park Quincy, MA 02169-7471 CSA International 8501 East

Pleasant Valley Road Cleveland, OH 44131-5575.

For power requirements, refer to the following table.

Series Voltage Frequency Rating

WOC97EC/

WOCA7EC

120/240 V AC 60 Hz 7.6 kW

120/208 V AC 60 Hz 6.2 kW

WOC75EC 120/240 V AC 60 Hz 7.5 kW

120/208 V AC 60 Hz 6.1 kW

WOC54EC 120/240 V AC 60 Hz 7.5 kW

120/208 V AC 60 Hz 6.1 kW

A. Model/serial/rating plate

A

5

INSTALLATION INSTRUCTIONS

Prepare Built-In Oven

1. Decide on the ﬁnal location for the oven. Avoid drilling or

cutting into house wiring during installation.

2. To avoid ﬂoor damage, set the oven onto cardboard prior

to installation. Do not use handle or any portion of the front

frame for lifting.

3. Remove the shipping materials and tape from the oven.

Remember to keep the corner posts and other materials that

may be needed for installation.

4. Remove the hardware package from inside the package

containing literature.

5. Remove and set aside racks and other parts from inside the

oven.

6. Move oven and cardboard close to the oven’s ﬁnal location.

Remove Oven Door(s)

IMPORTANT: Use two hands to remove oven door. For double

ovens, repeat the process for each door.

1. Prior to removing the oven door, prepare a surface where

you will place it. This surface should be ﬂat and covered with

a soft blanket, or use the corner posts from your packaging

material.

2. Fully open the oven door.

3. Locate the oven door hinge locks in both corners of the oven

door, and rotate the hinge locks toward the oven door to the

unlocked position. If the door hinge lock is not rotated fully

(see illustration B), the door will not remove properly.

4. Gently start to close the door. The door will stop at a partially

closed position.

5. Using two hands, grasp the edges of the oven door. Close

the oven door slightly past the stop position to take the

weight off of the door hinges, and then pull the oven door

up.

6. Pull the oven door toward you, and then remove it. You may

need to gently shift the door from side to side as you pull.

7. Set the oven door aside on the prepared covered work

surface with the oven door resting on its handle.

WARNING

Excessive Weight Hazard

Use two or more people to move and install oven.

Failure to do so can result in back or other injury.

Door

Hinges

A. Oven door hinge lock in

locked position

B. Oven door hinge lock in

partially unlocked position

Locked

position

Unlocked

position

Grip here

to rotate

Soft close hinge

arm on select models

6

Replace Oven Door(s)

1. Using two hands, grasp side edges of door at the midpoint.

Face the oven cavity.

2. Locate the slots on each side of the oven front frame for the

door hinge locks.

3. Using two hands, grasp the edges of the oven door. At a 45°

angle, insert the hinges at the same time, and push the oven

door into the oven cavity slot to replace. You may need to

gently shift the door from side to side as you push.

4. Make sure the door hinge notch is engaged on the bottom of

the oven cavity slot.

IMPORTANT: Do not close the door at this step or damage may

occur to the door hinge.

5. Lower the oven door to the fully open position. If the oven

door does not open to a full 90°, repeat steps 1 through 3.

6. Locate the oven door hinge locks in the corners of the oven

door, and rotate the hinge locks toward the oven cavity to

the locked position.

7. After the door hinges have been locked, gently swing the

door upward to close. The door should not be forced closed.

8. When the hinges are properly installed and the door is

closed, there should be an even gap between the door and

the control panel. If one side of the oven door is lower than

the other, the hinge on that side is not properly installed.

See the “Remove Oven Door(s)” and “Replace Oven Door(s)”

sections.

A. Slot in the oven cavity for door hinge lock

A

Unlocked

position

Locked

position

Soft close hinge

arm on select models

7

Make Electrical Connection

This oven is manufactured with a neutral (white) power supply

wire and a cabinet-connected green (or bare) ground wire

twisted together.

1. Disconnect power.

2. Feed the ﬂexible conduit from the oven through the opening

in the cabinet.

3. Remove junction box cover, if it is present.

4. Install a UL Listed or CSA Approved conduit connector to

the junction box.

5. Route the ﬂexible conduit from the oven to the junction box

through a UL Listed or CSA Approved conduit connector.

6. Tighten screws on conduit connector.

7. See the “Electrical Connection Options Chart” to complete

installation for your type of electrical connection.

Electrical Connection Options Chart

4-Wire Cable from Home Power Supply

IMPORTANT: Use the 4-wire cable from home power supply

in the U.S. where local codes do not allow grounding through

neutral, New Branch circuit installations (1996 NEC), mobile

homes and recreational vehicles, new construction and in

Canada.

1. Connect the two black wires (B) together using a UL Listed

wire connector.

2. Connect the two red wires (C) together using a UL Listed

wire connector.

3. Untwist white wire from green (or bare) ground wire coming

from the oven.

4. Connect the two white wires (F) together using a UL Listed

wire connector.

5. Connect the green (or bare) ground wire (H) from the oven

cable to the green (or bare) ground wire (in the junction box)

using a UL Listed wire connector.

6. Install junction box cover.

3-Wire Cable from Home Power Supply: U.S. Only

IMPORTANT: Use the 3-wire cable from home power supply

where local codes permit a 3-wire connection.

WARNING

Electrical Shock Hazard

Disconnect power before servicing.

Use 8 gauge copper wire.

Electrically ground oven.

Failure to follow these instructions can result in death,

fire, or electrical shock.

A. UL listed or CSA approved conduit connector

A

If your home has: Go to section:

4-Wire 4-Wire Cable from Home

Power Supply

3-Wire 3-Wire Cable from Home

Power Supply

1/2"

(13 mm)

1/2"

(13 mm)

A. Cable from home power supply

B. Black wires

C. Red wires

D. 4-wire ﬂexible conduit from

oven

E. Junction box

F. White wires

G. UL listed wire connectors

H. Green (or bare) ground wires

I. UL Listed or CSA Approved

conduit connector

A

D

F

H

B

C

E

G

I

A. Cable from home power

supply

B. Junction box

C. Black wires

D. White wires

E. Green (or bare) ground wire

(from oven)

F. 4-wire ﬂexible conduit from

oven

G. Red wires

H. UL Listed wire connectors

I. UL Listed or CSA Approved

conduit connector

B

C

D

E

F

H

G

A

I

8

1. Connect the two black wires (C) together using a UL Listed

wire connector.

2. Connect the two white wires (D) and the green (or bare)

ground wire (of the oven cable) using a UL Listed wire

connector.

3. Connect the two red wires (G) together using a UL Listed

wire connector.

4. Install junction box cover.

Install Oven

1. Using two or more people, lift the oven partially into cabinet

cutout. Use the oven opening as an area to grip.

NOTE: Push against seal area of oven front frame when

pushing oven into cabinet. Do not push against the outside

edges.

2. Push against the seal area of the front frame to push the

oven into the cabinet until the back surface of the front frame

touches the front wall of the cabinet.

3. Push the oven completely into the cabinet and center oven

into cabinet cutout.

4. Remove the tape from the black front trim, and remove the

zip tie from the mounting spacer.

■ Securely fasten the oven to the cabinet using the

#8-14 x 1" screws provided.

■ Insert the screws through holes in black trim, aligning

with the holes in oven frame and mounting spacers

already in place. Do not overtighten screws.

A. Oven frame

B. Mounting spacer

C. Oven frame hole

D. Black trim piece

A

C

D

B

9

5. The bottom vent and bottom vent trim (required when the

oven is installed with the feet in the tall position) are shipped

in the foam packing at the top of the oven.

To install only the bottom vent, see the following instructions.

To install both the bottom vent and the bottom vent trim

for installations with the feet in the tall position, see the

instructions in Step 6.

■ Align vent tab (B) with oven frame (A) as shown.

■ Using one #8-18 x 3/8" (9.5 mm) screw (D) on each side

of the vent tab (B), fasten the vent securely to the oven.

6. On models with the feet installed in the tall position, the

bottom vent trim must also be installed. See the following

instructions to install.

■ Flex the upper vent piece (C) away from the lower vent

piece (D) to slide the bottom vent trim (B) between them.

Some force may be required to ﬂex the upper vent trim

(C) away from the lower vent trim (D). Some force may

also be required to ﬂex the bottom vent trim (B) and

slide it into position. Make sure screw holes are properly

aligned between the two pieces. See the following

illustration.

■ Install the bottom vent trim (B) to the lower vent piece (D)

using two #8-18 x 1/4" (6.4 mm) screws on each side.

■ Align vent tab (B) with oven frame (A) as shown.

■ Using one #8-18 x 3/8" (9.5 mm) screw (E) on each side of

the vent tab (B), fasten the vent securely to the oven.

7. Replace the oven racks.

8. Replace the oven door. See the “Replace Oven Door(s)”

section.

9. Check that the door is free to open and close. If it is not,

repeat the removal and installation procedures. See the

“Prepare Built-In Oven” section.

10. Repeat for lower oven door.

11. Reconnect power.

12. The display panel will light brieﬂy, and “PF” should appear in

the display.

13. If the display panel does not light, reference the “Warranty”

section of the Use and Care Guide.

Install Warming Drawer Deector Kit

(only for ovens installed above

warming drawers)

On combo microwave/oven models installed above a warming

drawer, a warming drawer deﬂector kit must be installed. See the

“Tools and Parts” section for information on ordering.

Parts Supplied

A. Oven frame

B. Vent tab

C. Oven vent

D. #8-18 x 3/8" (9.5 mm)

screws

A

C

D

B

A. #8-18 x 1/4" (6.4 mm)

screws

B. Bottom vent trim

C. Upper vent piece

D. Lower vent piece

D

B

A

C

D

C

B

A. Oven frame

B. Vent tab

C. Oven vent

D. Bottom vent trim

E. #8-18 x 3/8" (9.5 mm)

screw

A

C

D

B

E

A. Phillips head screws (4)

only 2 screws for 27" (68.6 cm) size

B. Warming drawer deﬂector (1)

B

A

10

Install Deector Kit

1. Align the deﬂector (B) with the vent (C) as shown.

2. Using two #8-18 x 1/4" (6.4 mm) screws (A) on each side of

the deﬂector (B), fasten the deﬂector securely to the vent.

NOTE: On 27" (68.6 cm) models, only one #8–18 x 1/4"

(6.4 mm) screw is used on each side.

3. Align vent tab (B) with oven frame (A) as shown.

4. Using one #8-18 x 3/8" (9.5 mm) screw (E) on each side of

the vent tab (B), fasten the vent securely to the oven.

Complete Installation

1. Check that all parts are now installed. If there is an extra

part, go back through the steps to see which step was

skipped.

2. Check that you have all of your tools.

3. Dispose of/recycle all packaging materials.

4. For oven use and cleaning, read the Use and Care Guide.

Check Operation of Lower Oven

1. At ﬁrst use, set up the languages, clock, and any other

preferences, if available. For more information, read the Use

and Care Guide.

2. Press OVEN.

3. Select Cooking Method.

4. Select BROIL.

5. Set the temperature.

6. Press START.

If oven does not operate, check the following:

■ Household fuse is intact and tight or circuit breaker has

not tripped.

■ Electrical supply is connected.

■ See the “Troubleshooting” section in the Use and Care

Guide.

7. When oven has been on for 5 minutes, check for heat.

If you do not feel heat or if an error message appears in the

display, turn off the oven and contact a qualiﬁed technician.

8. Press OVEN on single ovens to cancel.

■ Press UPPER/LOWER on double ovens to cancel.

Check Operation of Microwave Oven

1. Fill a microwave-safe container with 1 cup (250 mL) of water

and place container inside microwave oven. Close door

ﬁrmly.

2. Press MICROWAVE.

3. Select Cooking Method.

4. Set microwave oven cook time to 2 minutes.

5. Press START. The interior microwave oven light should be

on, and the remaining cooking time should be displayed.

When display reads “1:00”, open microwave oven door.

The microwave should stop cooking. Close door ﬁrmly. The

interior microwave oven light should turn off.

6. Press START. Microwave oven should begin cooking, and

the microwave oven interior light should be on.

Let microwave oven complete cooking time. A tone will

sound four times at the end of the cooking time, and the

microwave oven will shut off.

7. Open microwave oven door and slowly remove container.

Water in container should be hot.

If you need Assistance or Service:

Please reference the “Assistance or Service” section of the Use

and Care Guide or contact the dealer from whom you purchased

your built-in and microwave ovens.

A. #8–18 x 1/4" (6.4 mm) screws

B. Warming drawer deﬂector

C. Vent

D

B

A

C

D

C

B

A. Oven frame

B. Vent tab

C. Oven vent

D. Warming drawer deﬂector

E. #8–18 x 3/8" (9.5 mm) screw

A

C

D

B

E

Page is loading ...

Whirlpool WOC75EC0HS02 Installation guide

Whirlpool WOC75EC0HS02 Installation guide

in other languages

Related papers

Other documents