Elation EPV762 MH User manual

Brand: Elation

Model: EPV762 MH

Category: Floodlights

Type: User manual

EPV762 MH

Elation Professional

6122 S Eastern Ave

Los Angeles, Ca 90040

www.elationlighting.com

Contents

1. Introduction……………………………………………………………………………………………………………..…….1

1.1. Brief Instruction …………………………………………………………………………………….…………….1

1.2. Package Accessories…………………………………………………………………….……………………….1

2. Features………………………………………..……………………………………………..…………….………………….1

3.TECHNICAL SPECIFICATIONS…………………………………….………………..……….……………………….2

4 .Overview ………………………………………………………………………………………………………………………. 3

5 .Safety Info …………………………………………………………………………………………………………………… 4

5.1. Important Safety Caution………………………………………………………………………………….. 4

5.2. GENERAL GUIDELINES………………………………………………………………………….…………… 4

6 .Installation Instruction………………………………………………………………………………………………….. 5

7 . DMX-512 control connection……………………………………………………………………………………….. 6

8 .Connection of PC and Controller…………………………………………………………………………………… 7

9 . DMX-512 connection with DMX terminator……………………………………………………………….. 7

10 . Projector DMX starting address selection………………………………………………………………… 8

11 . Control Board……………………………………………………………………………………………………………. 8

12 . INSTRUCTIONS ON USE…………………………………………………………………………………………... 15

Software fractional introduce

13 Installation and Application of LED Managing Tool …………………………………………………… 17

13.1. Features ………………………………………………………………………………………………………….…. 17

13.2. Operating Environment ……………………………………………………………………………………. 17

13.3. Installation………………………………………………………..……………………………………………….. 17

13.4. Uninstallation……………………………………………………………………………………………………… 18

14 Use details …………………………………………………………………………………………………….…………. 18

14.1. Program composition.……………………………………………………………………………………... 18

14.2. Introduction of interface window ……………………………………………………………………. 19

14.3. Feature detail…………………………………………………..……………………………………………….. 20

14.4. Progress of Program production………………………………………………………………………. 25

15 Text display …………………………………………………………………………………………………….…………. 29

15.1. Play single-line window.…………………………………………………………………………………... 29

15.2. Play multi-line window ……………………………………………………………………………………. 30

15.3. Play Word/Excel…………………………………………………..…………………………………………….. 32

16 Image display ………………………………………………………………………………………………….…………. 33

16.1. New multimedia window.………………………………………………………………………………... 33

16.2. Set multimedia window …………………………………………………………………………………… 33

16.3. Open the play file…………………………………………………..………………………………………….. 33

16.4. Set the play image properties………………………………………………………………..…………. 34

17 Video display ………………………………………………………………………………………………….………….. 35

17.1. New multimedia window.……………………………………………………………………………….... 35

17.2. Set multimedia window ………………………………………………………………………………….. 35

17.3. Open play file…………………………………………………..……………………………………………….. 35

17.4. Set property of Video files………………………………………………………..…………..…………. 36

18 Table display ………………………………………………………………………………………………….………….. 36

18.1. New multimedia window.……………………………………………………………………………….... 36

18.2. Set multimedia window ……………………………………………………………………………………. 36

18.3. Insert & Edit table……………………………………………..…………………………………………….. 36

19 Web display ………………………………………………………………………………………………….………….. 38

19.1. New multimedia window.………………………………………………………………………………... 38

19.2. Set multimedia window …………………………………………………………………………………… 39

19.3. Open playing grogram file…………………………………………………..……………………………. 39

19.4. Set Web Properties…………………………………………………………..……………….…..…………. 39

20 Database display ………………………………………………………………………………………….………….. 40

20.1. New multimedia window.………………………………………………………………………………... 40

20.2. Set multimedia window …………………………………………………………………………………… 40

20.3. New Access Database………………………………………………..……………………………………. 40

20.4. Add ODBC drive database…………………………………………………………..……………….……. 43

21 Date & Time ……………………………………………………………………………………….………….………….. 44

21.1. New multimedia window.………………………………………………………………………………... 44

21.2. Set multimedia window …………………………………………………………………………………… 44

21.3. Add data/time…………………………………………………..…………………………..…………………. 44

21.4. Set data/time………………………………………………………..…………………..……………….……. 44

22 Eternal Program ……………………………………………………………………………….………….………….. 46

22.1. New multimedia window.………………………………………………………………………………... 46

22.2. Set multimedia window …………………………………………………………………………………… 46

22.3. Open external program…………………………………………………..………………………………. 46

22.4. Set external program window………………………………………..………………………….……. 47

23 Timer Display ……………………………………………………………………………….………….……………… 48

23.1. New multimedia window.………………………………………………………………………………... 48

23.2. Set multimedia window …………………………………………………………………………………… 48

23.3. New timer Display………………………………………………………………………………………………. 48

23.4. Set timer………………………………………..………………………………………….……………….……. 48

24 Instant messaging …………………………………………………………………………….………….………….. 49

24.1. New instant messaging.………………………………………………………………………………... 49

24.2. Set instant messaging …………………………………………………………………………………… 49

24.3. Play instant messaging………………………………………………………………………………………. 50

25 Video input display …………………………………………………………………………….………….………….. 51

25.1. New multimedia window.………………………………………………………………………………... 51

25.2. Set multimedia window …………………………………………………………………………………… 51

25.3. New external video……………………………………………………………………………………………. 51

26 Flash Display ……………………………………………………………………………..…….………….………….. 53

26.1. Make Flash effect text.…………………………………………………………………………….……... 53

26.2. Play Flash ……………………………………………………………………………………….………………… 54

27 Screen capture ……………………………………………………………………………….………….………….. 56

27.1. New multimedia window.………………………………………………………………………………... 56

27.2. Set multimedia window …………………………………………………………………………………… 56

27.3. New screen capture……………………………………………………………………………………………. 56

27.4. Set screen capture………………………………………..………………………….……………….……. 56

27.5. Record………………………………………………………………………….……………………………………. 57

27.6. Play video………………………………………..………………………………………….……………….……. 57

28 Time Display …………………………………………………………………………………….………….………….. 58

28.1. Open time repertoire.……………………………………………………………………………………... 58

28.2. Add time repertoire ……………………………………………………….………………………………… 58

28.3. Edit time repertoire……………………………………………………………………………………………. 60

28.4. Delet time repertoire……………………………………..………………………….……………….……. 60

28.5. Start time repertoire…………………………………………………….……………………………………. 60

28.6. Exit…………………………………………………..………………………………………….……………….……. 60

29 Environment Monitoring ………………………………………………………………….………..….………….. 61

29.1. Open Brightness Control Repertoire.………………………………………………………………... 61

29.2. New brightness control repertoire ……………………………………………………….………… 61

29.3. Edit brightness control repertoire………………………………………………..…………………. 62

29.4. Delete brightness control repertoire……………………………………….……………….……. 62

29.5. Restore fault brightness control repertoire……………………………………………………. 63

30 Software Setting …………………………………………………………………………….………..….………….. 63

30.1. Set basic properties of software.…………………………………………..………………………... 63

31 Hardware setting …………………………………………………………………………….………..….………….. 64

32 Screen control ……………………………………………………………………………….………..….………….. 64

32.1. Set brightneess/contrast/Color temprature.…………………………………………………... 64

32.2. Set Screen Location ………………………………………………………..…….…………………..…… 65

32.3. Close/Freeze screen…………………………………..……………….……………….……………………. 66

33 View Device Status …………………………………………………………………………………..….………….. 67

33.1. Open Device Status.……………………………………………………………………………………….... 67

34 View environment monitoring ……………………………………………………….………..….………….. 69

34.1. Open environment monitoring.…………………………………………………..…………………... 69

34.2. Set Environment monitoring factors ………………………………..…….…………………..… 69

35 FAQ ………………………………………………………………………………………………………….….………….. 71

1. Introduction

1 1 Brief Instruction

Thank you for having chosen this professional LED lighting.

You will see you have acquired a powerful and versatile device. For your own safety and

utilize all wonderful functions of our LED screen, please read this user manual carefully

before installing the device.

Every person involved with the installation, operation and maintenance of this device has

- be qualified

- follow the instructions of this manual

1 2 Package Accessories:

1. One XLR connection cable

2. One power cable

3. Reticle

4. One Safety rope

5. Two omega clamps

6. Manual

Please check carefully that there is no damage caused by transportation. Should there be

any, consult your dealer and don’t install this device.

2. Features

• Channel modes: 6 channels

• Pan/tilt movement: 8 bit and 16 bit resolution

For smooth and precise resolution

Pan: 540°/630° optional, Tilt: 265°movement

High speed of pan/tilt movement, speed of pan/tilt movement is adjustable

Scan position memory, auto reposition after unexpected movement

• Excellent effect: apply dynamic scanning technology, screen with strong brightness, and

fine contrast

• Slender and clear image, vivid and multiform video, smooth and living visual effects

• Neat structure: aluminium material, super-light-thin-strong, and good light

transmittance

• Easy installation and maintenance: light-thin-strong modular design to make easy

movement, installation and maintenance

• Good and stable quality: we use imported light-emitting materials, high-quality IC chip,

high-power and noise-free power supply to achieve perfect quality

• Flexible format: can be scheduled with any display mode

• Rich content: can display text, graphics, images, animation, video information

• Big capacity of info: unlimited information display

• 50 000 hours LED life

• Bule and white LCD display

• Auto-program: 7 pre-built programs can be selected

• Software-upload by optional accessory via DMX line

3. TECHNICAL SPECIFICATIONS

Pixels Placing 7.62MM

Pixels Density 17222dots/m2

View Angle H145°/V110°

Video Output DVI

Power supply AC 100-240V~, 50/60Hz

Power consumption 320W

Unit Size 488 x 488mm

Net weight 24KG/ screen

4. Overview

5. Safety Info

5 1 Important Safety Caution

1 LCD Display

2 Mode/esc Button

3 Menu UP Button

4 Menu DOWN Button

5 Enter Button

6 Microphone

7 5-Pin DMX in

8 5-Pin DMX out

9 3-Pin DMX in

10 3-Pin DMX out

11) Power in

12) Fuse

13 Signal out

14 Signal in

15) Carrying handle

16) LED CURTAIN

17 Yoke

This LED CURTAIN has left the factory in perfect condition. In order to maintain this

condition and to ensure a safe operation, it is absolutely necessary for the user to follow

the safety instructions and warning notes written in this user manual.



If the LED CURTAIN has been exposed to temperature changes due to environmental

changes, do not switch it on immediately. The arising condensation could damage the

LED CURTAIN. Leave the device switched off until it has reached room temperature.



Make sure operation after every piece of LED connected properly.



Make sure that the available voltage is not higher than stated at the end of this

manual.



Make sure the power cord is never crimped or damaged by sharp edges. If this would

be the case, replacement of the cable must be done by an authorized dealer.



Always disconnect from the mains, when the device is not in use or before cleaning it.

Only handle the power cord by the plug. Never pull out the plug by tugging the power

cord.



Please be aware that damages caused by manual modifications to the device are not

subject to warranty. Keep away from children and non-professionals.



If the external flexible cable or cord of this luminaire is damaged, it shall be exclusively

replaced by the manufacturer or his service agent or a similar qualified person in order

to avoid a hazard.

5 2 GENERAL GUIDELINES



This device is a lighting effect for professional use on stages, in discotheques,

theatres, exposition, etc.



This fixture is only allowed to be operated with the max alternating current which

stated in the technical specifications in the last page of this manual



Lay the LED screen carefully, avoid the heavy pressure on LEDs.



Fixtures cannot be installed on combustible substances, keep more than 50cm

distance with wall for smooth air flow, so there should be no shelter for fans and

ventilation for heat radiation.



Always fix the fixture with an appropriate safety cable if you use the quick lock cam in

hanging up the fixture, please make sure the 4 quick lock fasteners turned in the

quick lock holes correctly.



While choosing the installation-spot, please make sure that the device is not exposed

to extreme heat, moisture or dust.



When fixing the device on a raised-from-the- ground support, be sure to insert quick-

lock detain in the pre-arranged screw holes, and fix the device with an accessorial

safety cable.



Operate the device only after having familiarized with its functions. Do not permit

operation by persons not qualified for operating the device. Most damages are the

result of unprofessional operation.



Please use the original packaging if the device is to be transported.



For safety reasons, please be aware that device teardown are forbidden.



If this device will be operated in any way different to the one described in this manual,

the product may suffer damages and the guarantee becomes void.

6. Installation Instruction

a). The operating temperature of this device is -15

C ~ 50

C and moisture within

10%~95%, please use the device not exceed this range.

b). The installation of the effect has to be built and constructed in a way that it can hold

10 times the weight for 1 hour without any harming deformation.

c). Never stand directly below the device when mounting, removing or servicing the

fixture.

d). The operator has to make sure the devices are properly connected according to this

manual

Installtion Instruction

a) Fixed the clamp on the bracket by tighten up the M12 screw on the bracket to the Ф13

hole in the middle of the bracket.

b) Insert the quick-lock fasteners of the first Omega holder into the respective holes on

the bottom of the device. Tighten the quick-lock fasteners fully clockwise.

c) Install the second Omega holder.

d) Pull the safety-rope through the holes on the bottom of the base and over the trussing

system or a safe fixation spot. Insert the end in the carabine and tighten the safety

screw.

Notice: this step is quite important to ensure that the fixture will not drop out

by the damage of the clamp.

7. DMX-512 control and signal connection

DMX-512 control connection

Connect the provided XLR cable to the female 3-pin XLR output of your controller and the

other side to the male 3-pin XLR input of the moving head. You can chain multiple

Moving head together through serial linking. The cable needed should be two core,

screened cable with XLR input and output connectors. Please refer to the diagram below.

Starting address 1 Starting address 7 Starting address 13

Signal connection

For signal connection, please connect the signal cable end to led display transmitter first

outlet, a master card to connect to the led display of the engine signal inputs. from the

first screen of the signal output is connected to the second block display output, and so

on, until all display attached. The signal cable must be reticle connected to mother card

respectively, Please see the following signal connection picture:

8. Connection of PC and Controller

Connect the video display controller and PC DVI connector with DVI cable, then connect

controller to PC USB connector with USB cable, controller’s output cable connect to

vertical input of LED screen, see following picture:

9. DMX-512 connection with DMX

terminator

For installations where the DMX cable has to run a long

distance or is in an electrically noisy environment, such

as in a discotheque, it is recommended to use a DMX

terminator. This helps in preventing corruption of the digital control signal by electrical noise. The

DMX terminator is simply an XLR plug with a 120 Ω resistor connected between pins 2 and

3,which is then plugged into the output XLR socket of the last fixture in the chain. Please see

illustrations below.

10. Projector DMX starting address selection

All fixtures should be given a DMX starting address when using a DMX signal, so that the correct

fixture responds to the correct control signals. This digital starting address is the channel number

from which the fixture starts to “listen” to the digital control information sent out from the DMX

controller. The allocation of this starting address is achieved by setting the correct number on the

display located on the base of the device.

You can set the same starting address for all fixtures or a group of fixtures, or make different

address for each fixture individually.

If you set the same address, all the units will start to “listen” to the same control signal from the

same channel number. In other words, changing the settings of one channel will affect all the

fixtures simultaneously.

If you set a different address, each unit will start to “listen” to the channel number you have set,

based on the quantity of control channels of the unit. That means changing the settings of one

channel will affect only the selected fixture.

In the case of the moving head, which is 6channels fixture, you should set the starting address of the

first unit to 1, the second unit to 7(6 + 1), the third unit to13 (6+ 7), and so on.

A. LED Screen Controller

B. Signal out cable

C. Power switch

D. Power in cable

E. USB cable

F. DVI cable

G .USB cable

11. Control Board

There are four keys on the control panel , which could be used to set the address, turn

ON/OFF, operating the program and reset.

[Mode/Esc] press this key to enter into edit mode. Press this key under the edit mode if

you want to return to previous menu. it will exit from edit mode 60 seconds after the last

keypress

[UP] screen will flash when pressing this key in normal mode, the adress value

will increasing. Keep pressing this key, the address value will increase rapidly. it will exit

from flash 60 seconds after the last keypress. Press this key under edit mode, you can

choose the function you want from the buttom up in the menu.

[DOWN] screen will flash when pressing this key in normal mode, the adress value

will idecreasing. Keep pressing this key, the address value will decrease rapidly. it will exit

from flash 60 seconds after the last keypress. Press this key under edit mode, you can

choose the function you want from the top down in the menu.

[ENTER] this key is functionless when in normal mode. Press this key under the edit

mode, it will enter into next menu.

Func

tion

Mod

Set Dmx Address

Value Display

Set To Slave

Auto Program

Music Control

Set Dmx Address

Value Display

Set To Slave

Auto Program

Music Control

Set Dmx Address

Value Display

Set To Slave

Auto Program

Music Control

A001~AXXX

PAN……

Slave1,Slave2,Slave3

Master / Alone

A001~AXXX

PAN……

Slave1,Slave2,Slave3

Master / Alone

A001~AXXX

PAN……

Slave1,Slave2,Slave3

Master / Alone

A001~AXXX

PAN……

Slave1,Slave2,Slave3

Master / Alone

A001~AXXX

PAN……

Slave1,Slave2,Slave3

Master / Alone

DMX address setting

DMX value display

Slave setting

Auto program

Music control

Info

rmat

ion

Time Information

Current Time

Total Run Time

Clear Total Time

Current Time

Total Run Time

Clear Total Time

Current Time

Total Run Time

Clear Total Time

Current Time

Total Run Time

Clear Total Time

XXXX(Hours)

ON/OFF

XXXX(Hours)

ON/OFF

Power on running time

Fixture running time

Clear Fixture running tim

Info

rmat

ion

Software Version

Ver1.0

Software version of each IC

Pers

onali

Status Settings

Address via DMX

No DMX Status

Pan Reverse

Fine Resolution

Feedback

Movement Speed

Mic Sensitivity

Address via DMX

No DMX Status

Pan Reverse

Fine Resolution

Feedback

Movement Speed

Mic Sensitivity

Address via DMX

No DMX Status

Pan Reverse

Fine Resolution

Feedback

Movement Speed

Mic Sensitivity

Address via DMX

No DMX Status

Pan Reverse

Fine Resolution

Feedback

Movement Speed

Mic Sensitivity

Address via DMX

No DMX Status

Pan Reverse

Fine Resolution

Feedback

Movement Speed

Mic Sensitivity

ON/OFF

Initial/Hold/Auto/Music

ON/OFF

Speed 1~ 4

70%, 0~99%

ON/OFF

Initial/Hold/Auto/Music

ON/OFF

Speed 1~ 4

70%, 0~99%

Add. via DMX

Auto run if no DMX

Pan Reverse movement

Fine resolution switch

Movement Feedback switch

Movement Mode Select

Sensitivity of Mic.

Pers

onali

Display Setting

Shutoff Time

Display shutoff time

Pers

onali

Initial Effect

PAN

PAN =XXX

Initial effect position

Pers

onali

Reset Default

ON/OFF

Restore factory sett.

Effe

Adju

Calibrate Values

--Password--

PAN:

--Password--

PAN:

--Password--

PAN:

--Password--

PAN:

Password=XXX

PAN =XXX:

Password=XXX

PAN =XXX:

Password=XXX

PAN =XXX:

Calbrate and adjust the

effects to standard/right

position Password “050”

Rese

Func

tion

Reset All

Reset Pan&Tilt

Reset all motors

Reset Pan

Edit

Prog

ram

Select Programs

Auto Pro Part 1

Auto Pro Part 2

Auto Pro Part 3

Auto Pro Part 1

Auto Pro Part 2

Auto Pro Part 3

Auto Pro Part 1

Auto Pro Part 2

Auto Pro Part 3

Program 1 ~ 10 Program 1

Program 1 ~ 10 Program 2

Program 1 ~ 10 Program 3

Program 1 ~ 10 Program 1

Program 1 ~ 10 Program 2

Program 1 ~ 10 Program 3

Program 1 ~ 10 Program 1

Program 1 ~ 10 Program 2

Program 1 ~ 10 Program 3

Program 1 ~ 10 Program 1

Program 1 ~ 10 Program 2

Program 1 ~ 10 Program 3

Select programs to be run

Edit

Prog

ram

Edit Program

Program 1

Program 10

Program 1

Program 10

Program 1

Program 10

Program Test

Step 01=SCxxx

Step 64=SCxxx

Program Test

Step 01=SCxxx

Step 64=SCxxx

Program Test

Step 01=SCxxx

Step 64=SCxxx

(“STEP XX”)

Testing program

Program in loop

Save and exit

Edit

Prog

ram

Edit Scenes

Edit Scene 001

~ Edit Scene 250

Edit Scene 001

~ Edit Scene 250

Edit Scene 001

~ Edit Scene 250

Pan,Tilt,……

--Secne Time--

Input By Outside

Pan,Tilt,……

--Secne Time--

Input By Outside

Pan,Tilt,……

--Secne Time--

Input By Outside

Pan=xxx……

TIME=xx.xs

Save and automatically

return

manual scenes edit

Edit

Prog

ram

Rec. Controller

XX~XX

Automat. scenes rec

Default settings shaded

Function Mode

DMX Address Setting

With this function, you can adjust the desired DMX-address via the Control Board.

• Select “Set DMX address” via the encoder.

• Press the encoder, adjust the DMX address by turning the encoder.

• Press the encoder to confirm.

• Press the Mode/Esc-button in order return to the main menu.

Display the DMX 512 value of each channel

With this function you can display the DMX 512 value of each channel. The display

automatically shows the channel with a value changing.

Slave Setting

With this function, you can define the device as slave.

Auto Program

With this function, you can run the internal program. You can select the desired program

under “Select program”. You can set the number of steps under “Edit program”. You can

edit the individual scenes under “Edit scenes”. With this function, you can run the

individual scenes either automatically, i.e. with the adjusted Step-Time.

Music control

With this function, you can run the internal program sound-controlled.

Information

Time information

Current Time

With this function, you can display the temporary running time of the device from the last

power on. The display shows “XXXX”, “XXXX” stands for the number of hours. The counter

is resetted after turning the device off.

Total Run Time

With this function, you can display the running time of the device. The display shows

“XXXX”, “XXXX” stands for the number of hours.

Clear Total Time

With this function, you can clear total run time of the fixture. The display shows “ON” or

“OFF”, Press “Enter” to confirm.

Software version

With this function, you can display the software version of the device.

• Select “Software version” by turning the encoder.

• Press the encoder, the display shows “V-X.X”, “X.X” stands for the version number, e.g.

“V-1.3”

• Turn the encoder in order to read the version of every individual IC.

• Press the Mode/Esc-button in order to return to the main menu.

PERSONALITY

Status Settings

Address Via DMX

With this function, you can adjust the desired DMX-address via an external controller.

• Select “Address via DMX” by turning the encoder.

• Press the encoder, the display shows “ON” or “OFF”.

• Turn the encoder to select “ON” if you wish to enable this function or “OFF” if you don’t.

• Press the encoder to confirm.

• Press the Mode/Esc-button in order to return to the main menu.

• On the controller, set the DMX-value of channel 1 to "7".

• Set the DMX-value of channel 2 to "7"or "8". When set to "7" you can adjust the starting

address between 1 and 255. When set to "8" you can adjust the starting address between

256 and 511.

• Set the DMX-value of channel 3 to the desired starting address. If you want to set the

starting address to 57, set channel 1 to "7", channel 2 to "7" and channel 3 to "57". If you

want to set the starting address to 420,set channel 1 to "7", channel 2 to "8" and channel

3 to "164" (256+164=420).

• Wait for approx. 20 seconds and the unit will carry out a reset. After that, the new

starting address is set.

Hold If No DMX

With this function, when the drive is not DMX signal, it runs automatism, close, hold and

music, the default is hold.

Pan Reverse

With this function you can reverse the Pan-movement.

Tilt Reverse

With this function you can reverse the Tilt-movement.

Feedback

With this function, you can feedback switch of pan movement or tilt movement.

Movement Speed

With this function, you can select scan mode from 1 to 4.

Mic Sensitivity

With this function, the default is 70%, you can select the desired microphone sensitivity

from 0 % to 99 %.

Display Setting

Shut off time

With this function you can shut off the LCD display after 2 to 59 minutes. Turn the encoder

in order to select the desired shut off time.

Initial Effect

With this function, Display initial effect position.

Reset Default

With this function, you can select restore factory set for ON or OFF, the default is OFF.

Effect Adjust

Calibrate values

With this function, you can calibrate and adjust the effect wheels to their correct positions.

The password of calibrate values is 050.

Reset-functions

With this function you can reset the device via the Control Board. You can select the

different reset functions by turning the encoder.

Edit program

Select program

With this function, you can select the program for the Program Run.

Edit program

With this function, you can edit the internal programs.

Edit scenes

With this function, you can edit the scenes of the internal programs.

Auto scenes rec.

The moving head features an integrated DMX-recorder by which you can transmit the

programmed scenes from your DMX-controller to the moving head. Adjust the desired

scene numbers via the encoder (from – to). When you call up the scenes at your

controller, they will automatically be transmitted to the moving head.

Excursion:

A Master unit can send up to 3 different data groups to the Slave units, i.e. a Master unit

can start 3 different Slave units, which run 3 different programs. The Master unit sends

the 3 program parts in a continuous loop.

The Slave unit receives data from the Master unit according to the group which the Slave

unit was assigned to. If e.g. a Slave unit is set to “Slave 1” in the menu “Set to Slave”, the

Master unit sends “Auto Program Part 1” to the Slave unit. If set to “Slave 2”, the Slave

unit receives “Auto Program Part 2”.

To start a Auto Program please proceed as follows:

1. Slave-Setting

• Select “Function Mode” by turning the encoder.