Real Fyre DVI is a gas log set designed to be used with Peterson direct vent inserts. It comes with a set of logs, glowing embers, and bryte coals. The logs are made of ceramic and are designed to look like real wood. The glowing embers and bryte coals are made of a material that simulates the look of real fire. The set comes with instructions on how to place the logs, embers, and coals in the insert. The Real Fyre DVI is designed to provide a realistic-looking fire without the need for wood or other fuels. It is a convenient and easy-to-use way to add the ambiance of a fire to your home.
Real Fyre DVI is a gas log set designed to be used with Peterson direct vent inserts. It comes with a set of logs, glowing embers, and bryte coals. The logs are made of ceramic and are designed to look like real wood. The glowing embers and bryte coals are made of a material that simulates the look of real fire. The set comes with instructions on how to place the logs, embers, and coals in the insert. The Real Fyre DVI is designed to provide a realistic-looking fire without the need for wood or other fuels. It is a convenient and easy-to-use way to add the ambiance of a fire to your home.
1
LOG SET IMPORTANT INFORMATION
CAUTION...............WARNING...............IMPORTANT
USE ONLY PETERSON REAL FYRE BURNERS AND VALVES WITH THIS REAL FYRE LOG SET.
Important: Adequate ventilation is absolutely
necessary. Adequate spacing
between the logs is NECESSARY
and MUST be maintained. Some
carbon build up (sooting) may occur
where fl ames strike the logs. If carbon
build up (sooting) continues, correct
log placement before sooting becomes
worse.
This product is only warranted when used as part of a Robert H. Peterson Co. vented burner system.
WARNING: Use ONLY Peterson Real Fyre direct
vent inserts with this Real Fyre gas log
set. Failure to do so may result in
property damage or personal injury,
and will void listings, certifi cations,
and invalidate claims made to RHP.
Contact your local Real Fyre dealer if you
need more information.
This instruction contains log set and ember placement for these Real Fyre logs. You must position and
maintain the log layout as shown here to ensure proper operation of the direct vent insert. Incorrect log
installation could cause fl ame impingement and improper combustion, resulting in soot and/or excessive
by-products of combustion. DO NOT add any additional embers for this installation. Any additional embers
will cause unsafe operation. Use these logs only with a Peterson direct vent insert.
If you experience a continued accumulation of black carbon (soot) on your logs, the glass panel, or refractory
panels, it is an indication of incomplete combustion and you must correct the log placement as instructed
in this manual. If signifi cant sooting continues, stop using this gas log set.
Important: HANDLE LOGS WITH CARE AT ALL TIMES.
Please read these instructions completely and carefully.
ROBERT H. PETERSON CO. • 14724 East Proctor Avenue • City of Industry, CA 91746
L-A2-418REV 0 - 1705040845
LOG SET IMPORTANT INFORMATION
CAUTION...............WARNING...............IMPORTANT
USE ONLY PETERSON REAL FYRE DIRECT VENT INSERTS WITH THIS REAL FYRE LOG SET.
BURNT (SPLIT) AMERICAN OAK LOG PLACEMENT INSTRUCTIONS
DVL-30-2A shown
This log set is to be installed along
with the glowing embers and bryte
coals that are supplied with your
direct vent insert.
2
CAUTION: Burn hazard! Logs will remain hot for some time after
use. If you need to reposition any log to maintain the proper
layout, use heat resistant gloves or allow logs adequate time
to cool before handling.
Failure to use Peterson burners and valves may result in a DANGEROUS
situation and in property damage, personal injury or even death; will
void listings and certifi cations; and will void any insurance coverage
by R.H. Peterson Co or our insurers.
WARNING: This gas log set is for use with R.H. Peterson Co
burners (and parts) ONLY.
L-A2-418
REV 0 - 1705040845
CAUTION: Burn hazard! Logs will remain hot for some time after
use. If you need to reposition any log to maintain the proper
layout, use heat resistant gloves or allow logs adequate time
to cool before handling.
Failure to use Peterson burners and valves may result in a DANGEROUS
situation and in property damage, personal injury or even death; will
void listings and certifi cations; and will void any insurance coverage
by R.H. Peterson Co or our insurers.
WARNING: This gas log set is for use with R.H. Peterson Co
burners (and parts) ONLY.
Failure to use Peterson direct vent inserts may result in a DANGEROUS
situation and in property damage, personal injury or even death; will
void listings and certifi cations; and will void any insurance coverage
by R.H. Peterson Co or our insurers.
WARNING: This gas log set is for use with R.H. Peterson Co
direct vent inserts ONLY.
3
Burnt (Split) American Oak Log Placement Instructions (25" model)
IV
I
II
III
V
DVL-25-2(A,S)
PARTS LIST
All items for this log set are included in one (1) box.
CAUTION: Burn hazard! Logs will remain hot
for some time after use.
1
2
DVAL-17BR
DV(A,S)L-25BF
3
DVAL-9TC
4
5
DV(A,S)L-11TR
DV(A,S)L-10TL
1
Place the rear log (log #1) as shown. The bottom
of the log has two holes that align with two pegs
found on the burner.
Separate glowing embers
and place as shown here
Separate a portion of the glowing embers into
small pieces and evenly place them along the
rear and center burner ports as shown.
2 2
Place the left and right front log pieces (log #2)
as shown. The bottom of the logs each have two
holes that align with the pegs found on the burner.
Separate glowing embers
and place as shown here
(top view above front log)
Separate the remaining glowing embers into small
pieces and evenly place them along the front and
center burner ports as shown.
Separate bryte coals and
place as shown here
(top view above front log)
Separate the bryte coals into small pieces and
evenly place them above the front glowing embers
as shown.
Burnt American Oak log set shown
4
Burnt (Split) American Oak Log Placement Instructions (25" model) (Cont.)
VI
VII
3
Place the middle top log (log #3) as shown. The
rear log has a notch to aid in positioning the top log.
Place the left and right top logs (logs #4 and #5)
as shown. The logs below have notches to aid in
positioning the top logs.
5
4
5
Burnt (Split) American Oak Log Placement Instructions (30" & 36" models)
IV
I
II III
V
CAUTION: Burn hazard! Logs will remain
hot for some time after use.
DVL-(30,36)-2(A,S)
PARTS LIST
30" Burnt American Oak log set shown
1
2
4
3
5
6
30" - DVAL-18BR
36" - DVAL-24BR
30" - DV(A,S)L-30BF
36" - DV(A,S)L-36BF
All items for these log sets are included in one (1) box.
30" - DV(A,S)L-9TL
36" - DV(A,S)L-10T
DV(A,S)L-13T
DV(A,S)L-18T
*
1
Place the rear log (log #1) as shown. The bottom
of the log has two holes that align with two pegs
found on the burner.
Separate glowing embers
and place as shown here
Separate a portion of the glowing embers into
small pieces and evenly place them along the
rear burner ports, ember screen, and front carry
over ports as shown.
2
2
Place the left and right front log pieces (log #2)
as shown. The bottom of the logs each have two
holes that align with the pegs found on the burner.
Separate glowing embers
and place as shown here
(top view above front log)
Separate the remaining glowing embers into small
pieces and evenly place them along the front and
center burner ports as shown.
Separate bryte coals and
place as shown here
(top view above front log)
Separate the bryte coals into small pieces and
evenly place them above the front glowing embers
as shown.
30" - DVAL-10
36" - DVAL-12T
6
Burnt (Split) American Oak Log Placement Instructions (30" & 36" models) (Cont.)
3
Place the middle top log (log #3) as shown. The
rear log has a notch to aid in positioning the top log.
VI
VII
VIII
4*
5
Place the middle top log (log #6) as shown. The
logs below have notches to aid in positioning the
top log.
6
Place the left and right top logs (logs #4 and #5)
as shown. The logs below have notches to aid
in positioning the top logs.
*
For 36" models,
place log #4 as
shown in the
image to the
right.
4*
-
1
-
2
-
3
-
4
-
5
-
6
Real Fyre DVI Owner's manual
- Type
- Owner's manual
- This manual is also suitable for
Real Fyre DVI is a gas log set designed to be used with Peterson direct vent inserts. It comes with a set of logs, glowing embers, and bryte coals. The logs are made of ceramic and are designed to look like real wood. The glowing embers and bryte coals are made of a material that simulates the look of real fire. The set comes with instructions on how to place the logs, embers, and coals in the insert. The Real Fyre DVI is designed to provide a realistic-looking fire without the need for wood or other fuels. It is a convenient and easy-to-use way to add the ambiance of a fire to your home.
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Real Fyre DVI Charred Rustic Oak Log Owner's manual
-
-
-
-
-
-
-
-
-
Other documents
-
Real Flame S9-2-30 Owner's manual
-
R.H. Peterson realfyre G5 Series Owner's manual
-
-
Lopi 34 DVL Gas Fireplace Insert Installation guide
-
-
-