MTD 12A-569Q795 Owner's manual

Category
Lawnmowers
Type
Owner's manual

MTD 12A-569Q795 is a self-propelled lawnmower engineered to provide excellent performance when properly operated and maintained. It's a precision piece of power equipment, capable of mowing grass and helping you keep your lawn looking neat and tidy. To ensure safe and efficient operation, be sure to read and understand the instructions provided in the operator's manual before using the machine.

MTD 12A-569Q795 is a self-propelled lawnmower engineered to provide excellent performance when properly operated and maintained. It's a precision piece of power equipment, capable of mowing grass and helping you keep your lawn looking neat and tidy. To ensure safe and efficient operation, be sure to read and understand the instructions provided in the operator's manual before using the machine.

Safe Operation Practices Set=Up Operation Maintenance Service Troubleshooting Warranty
OPER roR's
L
Self Propelled Mower m Model Series 560
MTD LLC, P.O. BOX 361131 CLEVELAND, OHiO 44136-0019
PrintedInUSA FormNo.769-03487
(September17,2007)
ToTheOwner
1
ThankYou
Thank you for purchasing a Lawn Mower manufactured by
MTD LLC. It was carefully engineered to provide excellent
performance when properly operated and maintained.
Please read this entire manual prior to operating the equipment.
It instructs you how to safely and easily set up, operate and
maintain your machine. Please be sure that you, and any other
persons who will operate the machine, carefully follow the
recommended safety practices at all times. Failure to do so could
result in personal injury or property damage.
All information in this manual is relative to the most recent
product information available at the time of printing. Review
this manual frequently to familiarize yourself with the machine,
its features and operation. Please be aware that this Operator's
Manual may cover a range of product specifications for various
models. Characteristics and features discussed and/or illustrated
in this manual may not be applicable to all models. MTD LLC
reserves the right to change product specifications, designs and
equipment without notice and without incurring obligation.
This product has met the rigid safety standards of the Outdoor
Power Equipment Institute and an independent testing
laboratory. If you have any problems or questions concerning
the machine, phone your local authorized MTD service dealer
or contact us directly. MTD's Customer Support telephone
numbers, website address and mailing address can be found on
this page. We want to ensure your complete satisfaction at all
times.
Throughout this manual, all references to right and left side of the
machine are observed from the operating position
The engine manufacturer is responsible for all engine-related
issues with regards to performance, power-rating, specifications,
warranty and service. Please refer to the engine manufacturer's
Owner's/Operator's Manual, packed separately with your
machine, for more information.
Table of Contents
Safe Operation Practices ........................................ 3
Assembly & Set-Up .................................................. 8
Controls & Features ................................................ 11
Opera tion ................................................................ 12
Maintenance &Adjustment ................................. 14
Service ..................................................................... 16
Troubleshooting ..................................................... 18
Illustrated Parts List .............................................. 20
Warranty ................................................................ 24
RecordProductinformation
Before setting up and operating your new equipment, please
locate the model plate on the equipment and record the
information in the provided area to the right. You can locate the
model plate by standing at the operator's position and looking
down at the tea r of the deck. This information will be necessary,
should you seek technical support via our web site, Customer
Support Department, or with a local authorized service dealer.
MODEL NUMBER
EFIEFIEFIEFIEFIE
SERIAL NUMBER
71DF1DF1DF1DF1DE
CustomerSupport
Please do NOT return the machine to the retailer or dealer without first contacting our Customer Support Department.
If you have difficulty assembling this product or have any questions regarding the controls, operation, or maintenance of
this machine, you can seek help from the experts. Choose from the options below:
Visit us on the web at www.mtdproducts.com
Call a Customer Support Representative at (800) 800-7310 or (330) 220-4683
Write us at MTD LLC P.O. Box 361131 • Cleveland, OH 44136-0019
importantSafeOperationPractices
2
,A
WARNING: This symbol points out important safety instructions which, if not followed,
could endanger the personal safety and/or property of yourself and others. Read and follow
all instructions in this manual before attempting to operate this machine. Failure to comply
with these instructions may result in personal injury.
When you see this symbol. HEED ITS WARNING!
CALIFORNIA PROPOSITION 65
WARNING: Engine Exhaust, some of its constituents, and certain vehicle components
contain or emit chemicals known to State of California to cause cancer and birth defects
or other reproductive harm.
WARNING: Battery posts, terminals, and related accessories contain lead and lead
compounds, chemicals known to the State of California to cause cancer and reproductive
harm. Wash hands after handling.
DANGER: This machine was built to be operated according to the safe operation practices in
this manual. As with any type of power equipment, carelessness or error on the part of the
operator can result in serious injury. This machine is capable of amputating fingers, hands,
toes and feet and throwing objects. Failure to observe the following safety instructions
could result in serious injury or death.
GeneralOperation
1. Read this operator's manual carefully in its entirety before
attempting to assemble this machine. Read, understand,
and follow all instructions on the machine and in the
manuals) before operation. Keep this manual in a safe
place for future and regular reference and for ordering
replacement parts
2. Be completely familiar with the controls and the proper use
of this machine before operating it.
3. This machine is a precision piece of power equipment,
not a plaything. Therefore, exercise extreme caution at all
times. This machine has been designed to perform one job:
to mow grass. Do not use it for any other purpose.
4. Never allow children under 14 years of age to operate this
machine. Children 14 and over should read and understand
the instructions and safe operation practices in this manual
and on the machine and should be trained and supervised
by an adult.
5. Only responsible individuals who are familiar with these
rules of safe operation should be allowed to use this
machine.
6. Thoroughly inspect the area where the equipment is to be
used. Remove all stones, sticks, wire, bones, toys and other
foreign objects, which could be tripped over or picked up
and thrown by the blade. Thrown objects can cause serious
personal injury.
7. Plan your mowing pattern to avoid discharge of material
toward roads, sidewalks, bystanders and the like. Also,
avoid discharging material against a wall or obstruction,
which may cause discharged material to ricochet back
toward the operator.
8. To help avoid blade contact or a thrown object injury,
stay in operator zone behind handles and keep children,
bystanders, helpers and pets at least 75 feet from mower
while it is in operation. Stop machine if anyone enters area.
9. Always wear safety glasses or safety goggles during
operation and while performing an adjustment or repair
to protect your eyes. Thrown objects which ricochet can
cause serious injury to the eyes.
10. Wear sturdy, rough-soled work shoes and close-fitting
slacks and shirts. Shirts and pants that cover the arms
and legs and steel-toed shoes are recommended. Never
operate this machine in bare feet, sandals, slippery or light-
weight (e.g. canvas) shoes.
11. Do not put hands or feet near rotating parts or under the
cutting deck. Contact with blade can amputate fingers,
hands, toes and feet.
12. Amissingordamageddischargecovercancauseblade 27.
contactorthrownobjectinjuries.
13. Manyinjuriesoccurasaresultofthemowerbeingpulled
overthefootduringafallcausedbyslippingortripping.
Donotholdontothemowerifyouarefalling;releasethe
handleimmediately. 28.
14. Neverpullthemowerbacktowardyouwhileyouare
walking.Ifyoumustbackthemowerawayfromawallor
obstructionfirstlookdownandbehindtoavoidtripping
andthenfollowthesesteps:
a. Stepbackfrommowertofullyextendyourarms.
b. Besureyouarewellbalancedwithsurefooting.
c. Pullthemowerbackslowly,nomorethanhalfway
towardyou.
d. Repeatthesestepsasneeded.
Do:
15. Do not operate the mower while under the influence of
alcohol or drugs. 1.
16. Do not engage the self-propelled mechanism on machines
so equipped while starting engine. 2.
17. The blade control handle is a safety device. Never attempt
to bypass its operation. Doing so makes the safety device
inoperative and may result in personal injury through 3.
contact with the rotating blade. The blade control handle
must operate easily in both directions and automatically
return to the disengaged position when released.
18. Never operate the mower in wet grass. Always be sure of Do Not:
your footing. A slip and fall can cause serious personal
injury. If you feel you are losing your footing, release the
blade control handle immediately and the blade will stop
rotating within three seconds.
Mow only in daylight or good artificial light. Walk, never
run.
19.
20.
21.
22.
23.
24.
25.
26.
Stop the blade when crossing gravel drives, walks or roads.
If the equipment should start to vibrate abnormally, stop
the engine and check immediately for the cause.Vibration
is generally a warning of trouble.
Shut the engine off and wait until the blade comes to
acomplete stop before removing the grasscatcher or
unclogging the chute. The cutting blade continues to
rotate for a few seconds after the blade control isreleased.
Never place any part of the body in the blade area until you
are sure the blade hasstopped rotating.
Never operate mower without proper trail shield, discharge
cover, grass catcher, blade control handle or other safety
protective devices in place and working. Never operate
mower with damaged safety devices. Failureto do so can
result in personal injury.
Muffler and engine become hot and can causea burn. Do
not touch.
Never attempt to make a wheel or cutting height
adjustment while the engine is running.
Only use parts and accessories made for this machine by
the manufacturer. Failure to do so can result in personal
injury.
When starting engine, pull cord slowly until resistance
is felt, then pull rapidly. Rapid retraction of starter cord
(kickback) will pull hand and arm toward engine faster than
you can let go. Broken bones, fractures, bruises or sprains
could result.
If situations occur which are not covered in this manual,
use care and good judgement. Contact Customer Support
for assistance or the name of the nearest service dealer.
Slope Operation
Slopes are a major factor related to slip and fall accidents, which
can result in severe injury. Operation on slopes requires extra
caution. If you feel uneasy on a slope, do not mow it. For your
safety, use the slope gauge included as part of this manual to
measure slopes before operating this machine on a sloped or
hilly area. If the slope is greater than 15 degrees, do not mow it.
Mow across the face of slopes; never up and down. Exercise
extreme caution when changing direction on slopes.
Watch for holes, ruts, rocks, hidden objects, or bumps
which can cause you to slip or trip. Tall grass can hide
obstacles.
Always be sure of your footing. A slip and fall can cause
serious personal injury. If you feel you are losing your
balance, release the blade control handle immediately and
the blade will stop rotating within three (3) seconds.
1. Do not mow near drop-offs, ditches or embankments, you
could lose your footing or balance.
2. Do not mow slopes greater than 15 degrees as shown on
the slope gauge.
3. Do not mow on wet grass. Unstable footing could cause
slipping.
Children
Tragic accidents can occur if the operator is not alert to the
presence of children. Children are often attracted to the mower
and the mowing activity. They do not understand the dangers.
Never assume that children will remain where you last saw them.
Keep children out of the mowing area and under watchful
care of a responsible adult other than the operator.
Be alert and turn mower off if a child enters the area.
1.
2.
3.
4.
5.
6.
Before and while moving backwards, look behind and
down for small children.
Use extreme care when approaching blind corners,
doorways, shrubs, trees, or other objects that may obscure
your vision of a child who may run into the mower.
Keep children away from hot or running engines. They can
suffer burns from a hot muffler.
Never allow children under 14 years of age to operate this
machine. Children 14 and over should read and understand
the instructions and safe operation practices in this manual
and on the machine and be trained and supervised byan
adult.
4 I SECTION2 -- IMPORTANT SAFE OPERATION PRACTICES
Service
SafeHandling OfGas01ine:
I. To avoid personal injury or property damage use extreme
care in handling gasoline. Gasoline is extremely flammable
and the vapors are explosive. Serious personal injury can
occur when gasoline is spilled on yourself or your clothes,
which can ignite. Wash your skin and change clothes
immediately.
2. Use only an approved gasoline container.
3. Never fill containers inside a vehicle or on a truck or trailer
bed with a plastic liner. Always place containers on the
ground away from your vehicle before filling.
4. Remove gas-powered equipment from the truck or
trailer and refuel it on the ground. If this is not possible,
then refuel such equipment on a trailer with a portable
container, rather than from a gasoline dispenser nozzle.
5. Keep the nozzle in contact with the rim of the fuel tank or
container opening at all times until fueling is complete. Do
not use a nozzle lock-open device.
Extinguish all cigarettes, cigars, pipes and other sources
of ignition.
Never fuel machine indoors because flammable vapors will
accumulate in the area.
6.
7.
8.
Never remove gas cap or add fuel while engine is hot or
running. Allow engine to cool at least two minutes before
refueling.
9. Never over fill fuel tank. Fill tank to no more than 1 inch
below bottom of filler neck to provide for fuel expansion.
10. Replace gasoline cap and tighten securely.
11. If gasoline is spilled, wipe it off the engine and equipment.
Move machine to another area. Wait 5 minutes before
starting engine.
12. Never store the machine or fuel container near an open
flame, spark or pilot light as on a water heater, space
heater, furnace, clothes dryer or other gas appliances.
13. To reduce fire hazard, keep machine free of grass, leaves,
or other debris build-up. Clean up oil or fuel spillage and
remove any fuel soaked debris.
14. Allow machine to cool at least 5 minutes before storing.
GeneralService:
1. Never run an engine indoors or in a poorly ventilated area.
Engine exhaust contains carbon monoxide, an odorless
and deadly gas.
2. Before cleaning, repairing, or inspecting, make certain the
blade and all moving parts have stopped. Disconnect the
spark plug wire and ground against the engine to prevent
unintended starting.
3. Check the blade and engine mounting bolts at frequent
intervals for proper tightness. Also, visually inspect blade
for damage (e.g., bent, cracked, worn) Replace blade with
the original equipment manufacture's (O.E.M.) blade only,
listed in this manual. "Use of parts which do not meet the
original equipment specifications may lead to improper
performance and compromise safety!"
4. Mower blades are sharp and can cut. Wrap the blade or
wear gloves, and use extra caution when servicing them.
5. Keep all nuts, bolts, and screws tight to be sure the
equipment is in safe working condition.
6. Never ta roper with safety devices. Check their proper
operation regularly.
7. After striking a foreign object, stop the engine, disconnect
the spark plug wire and ground against the engine.
Thoroughly inspect the mower for any damage. Repair the
damage before starting and operating the mower.
8. Never attempt to make a wheel or cutting height
adjustment while the engine is running.
9. Grass catcher components, discharge cover, and trail shield
are subject to wear and damage which could expose
moving parts or allow objects to be thrown. For safety
protection, frequently check components and replace
immediately with original equipment manufacturer's
(O.EM.) parts only, listed in this manual. "Use of parts
which do not meet the original equipment specifications
may lead to improper performance and compromise
safety!"
10. Do not change the engine's governor setting or over-speed
the engine. The governor controls the maximum safe
operating speed of the engine.
11. Check fuel line, tank, cap, and fittings frequently for cracks
or leaks. Replace if necessary.
12. Do not crank engine with spark plug removed.
13. Maintain or replace safety and instruction labels, as
necessary.
14. Observe proper disposal laws and regulations. Improper
disposal of fluids and materials can harm the environment.
Donot modify engine
To avoid serious injury or death, do not modify engine in any
way. Tampering with the governor setting can lead to a runaway
engine and cause it to operate at unsafe speeds. Never tamper
with factory setting of engine governor.
NoticeRegardingEmissions
Engines which are certified to comply with California and federal
EPA emission regulations for SORE (Small Off Road Equipment)
are certified to operate on regular unleaded gasoline, and
may include the following emission control systems: Engine
Modification (EM) and Three Way Catalyst (TWC) if so equipped.
SECTION2 -- IMPORTANT SAFE OPERATION PRACTICES S
SparkArrestor
_ ARNING: This machine is equipped with an
internal combustion engine and should not be used
on or near any unimproved forest-covered, brush
covered or grass-covered land unless the engine's
exhaust system is equipped with a spark arrester
meeting applicable local or state laws (if any).
Ira spark arrester is used, it should be maintained in
effective working order by the operator. In the State of California
the above is required by law (Section 4442 of the California
Public Resources Code). Other states may have similar laws.
Federal laws apply on federal lands.
A spark attester for the muffler is available through your
nearest engine authorized service dealer or contact the service
department, P.O.Box 361131 Cleveland, Ohio 44136-0019.
AverageUsefulLife
According to the Consumer Products Safety Commission
(CPSC) and the U.S. Environmental Protection Agency (EPA),
this product has an Average Useful Life of seven (7) years, or 140
hours of operation. At the end of the Average Useful Life, buy
a new machine or have the machine inspected annually by an
authorized service dealer to ensure that all mechanical and
safety systems are working properly and not worn excessively.
Failure to do so can result in accidents, injuries or death.
WARNING: Your Responsibility--Restrict the use of this power machine to persons who read, understand and
follow the warnings and instructions in this manual and on the machine.
SAVETHESEiNSTRUCTIONS!
6 I SECTION 2 -- IMPORTANT SAFE OPERATION PRACTICES
Sight and hold this levelwith avertical tree...
I
I
|
!
!
!
!
!
or a corner of a building...
!
|
15 °
!--
Z
0
0
!--
Z
i
I
¢N
Z
0
i
I-
Usethis page asa guide to determine slopeswhere you may not operate safely.
WARNING: Do not operate your lawn mower on such slopes. Do not mow on inclines with a slope in excess of 15 degrees
(a rise of approximately 2-1/2 feet every 10 feet). A riding mower could overturn and cause serious injury. Operate riding
mowers up and down slopes, never across the face of slopes. Operate walk-behind mowers across the face of slopes, never
up and down slopes.
Assembly& Set-Up
3
Contents of Carton
One Lawn Mower
One GrassCatcher
One Side Discharge Chute
One Lawn Mower Operator's Manual
One Engine Operator's Manual
One Bottle of Oil
One Hardware Pack
Assembly
NOTE:This unit is shipped without gasoline or oil in the engine.
Fill up gasoline and oil as instructed in the accompanying engine
manual BEFORE operating your mower.
Handle
1.
Remove any packing material which may be between
upper and lower handles.
a. Pull up and back on upper handle as shown in Fig.
3-1. Make certain the lower handle is seated securely
into the handle mounting brackets. Do not crimp
cable while lifting the handle up.
Figure 34
b. Tighten star knobs to secure upper handle to lower
handle. Make sure that each carriage bolt is seated
properly in the handle.
2.
Locate the hairpin clip on the weld pin on each side of
lower handle.
a. Remove hairpin clip from this hole. Using a pair of
pliers, insert hairpin clip into the hole on pin closest
to the bracket. See Fig. 3-2. Repeat on other side.
Hardware Pack
b.
Figure 3=2
Insert a carriage bolt from the hardware pack into
the upper hole on the handle mounting bracket.
Secure with one plastic wing nut, also included
in the hardware pack. Repeat on other side with
remaining items from hardware pack.
3.
The rope guide is attached to the right side of the upper
handle. See Fig. 3-3. Loosen the wing nut which secures the
rope guide.
Figure 3-3
a. Hold blade control against upper handle.
b. Pull starter rope out of the engine. Release blade
control.
c. Slip starter rope into rope guide.
d. Tighten wing nut.
4. Insert post on cable tie into hole provided on the lower
handle. Pull cable tie tight and trim excess.
RearWheels
Install rear wheels as follows in Fig. 3-4 (wheels maybe already
installed at factory, if so disregard this step):
\
Figure 3-4
1.
2.
3.
4.
Place rear of the mower deck on raised blocks.
Remove lock nut from pivot arm assembly (on select
models, these may be included separately in a plastic bag).
Slide wheel, with hollow side in, onto pivot arm and secure
with lock nut.
Assemble the other side in the same manner.
GrassCatcher
Follow steps below to assemble the grass catcher. Make
certain bag is turned right side out before assembling
(warning label will be on the outside).
a. Place bag over frame so that its black plastic side is
at the bottom.
b.
Slip plastic channel of grass bag over hooks on the
frame. See Fig. 3-5. All the plastic channels except
center top of bag attach from outside of bag.
Figure 3-5
c. Attach center top of bag from inside of bag.
SECTION 3 -- ASSEMBLY& SET-UP 9
2_
Follow the steps below to attach the grass catcher:
a. Lift rear discharge door. See Fig. 3-6.
Figure 3-6
J
b. Place grass catcher on the pivot rod. Let go of
discharge door so that it rests on the grass catcher.
WARNING: Never operate mower unless the hooks
on the grass catcher are firmly seated on the pivot
rod and the rear discharge door rests firmly against
top of the grass catcher.
SideDischargeChute
Your mower is shipped as a mulcher. To convert to side
discharge, make sure grass catcher is off of the unit and rear
discharge door is closed.
1. On the side of the mower, lift the mulching plug. See
Figure 3-7.
f
2_
Slide two hooks of side discharge chute under hinge pin on
mulching plug assembly. Lower the mulching plug. Do not
remove side mulching plug at any time, even when you are
not mulching.
Adjustments
Each wheel has a height adjustment lever to change the cutting
height of the mower.
1. Depress height adjustment lever towards wheel.
2. Slide lever to desired position for a change in cutting
height. See Fig. 3-8.
F
Figure 3-8
3. Release lever towards deck.
IMPORTANT:All wheels must be placed in the same
relative position. For rough or uneven lawns, move the
height adjustment lever to a higher position. This will stop
scalping of grass.
(;asand OilRii-Up
Refer to the separate engine owner's manual for additional
engine information.
1. Add oil provided before starting unit for the first time out
of the box.
2_
Service the engine with gasoline as instructed in the
separate engine owner's manual.
WARNING: Use extreme care when handling
gasoline. Gasoline is extremely flammable and the
vapors are explosive. Never fuel the machine
indoors or while the engine is hot or running.
Extinguish cigarettes, cigars, pipes and other
sources of ignition.
k. j
Figure 3-7
SECTION 3 -- ASSEMBLY& SET-UP
ControlsandFeatures
4
Drive Controk
Recoil Starter ................
Side Discharge
Chute
Mulch Plu¢
Cutting Height
Adjustment Levers
J
Figure 44
BladeControl
The blade control is attached to the upper handle of the mower.
Depress and squeeze it against the upper handle to operate the
unit. Release itto stop engine and blade.
_ ARNING: This blade control is a safety device.Never attempt to bypass its operations.
DriveControl
The drive control is located on the underside of the upper handle
and is used to engage the drive. Squeeze it against the upper
handle to engage the drive; release it to slow down or stop
mower from propelling.
Cutting Height AdjustmentLevers
One adjustment lever is located on each wheel and is used to
adjust the cutting height. All four levers have to be at the same
relative position to ensure a uniform cut.
MulchPlug
The mulch plug is used for mulching purposes. Instead of
collecting the grassclippings in a grass catcher or using the
side discharge chute, some mower models have the option
of recirculating the clippings back to the lawn. This is called
mulching.
SideDischargeChute
Your mower is shipped as a mulcher. To discharge the grass
clippings to the side instead, follow the instructions in the
Assembly & Set-Up section to attach the side discharge chute.
i_ll WARNING: Keep hands and feet away from the
chute area on cutting deck. Refer to warning label
on the unit.
RecoilStarter
The recoil starter is attached to the right upper handle. Stand
behind the unit and pull the recoil starter rope to start the unit.
11
Operation
Starting Engine
WARNING: Be sure no one other than the operator
is standing near the lawn mower while starting
engine or operating mower. Never run engine
indoors or in enclosed, poorly ventilated areas.
Engine exhaust contains carbon monoxide, an
odorless and deadly gas. Keep hands, feet, hair and
loose clothing away from any moving parts on
engine and lawn mower.
Follow the set of instructions pertaining to your unit. Refer to
engine manual for help with the engine.
Bfiggs & Stratt0n:
1. If equipped, push primer three times. Wait about two
seconds between each push. See Fig. 5-1. In temperature
around 55° F or below, prime five times. Do not prime to
restart a warm engine.
2. Standing behind the mower, squeeze the blade control
against upper handle.
3. Holding these two handles together firmly, grasp recoil
starter handle and pull rope out with a rapid, continuous,
full arm stroke. See Fig. 5-1. Keeping a firm grip on the
starter handle, let the rope rewind slowly. Repeat until
engine cranks. Let the rope rewind each time slowly.
HondaEngine:
I. Place the fuel valve lever found on the left side of the
engine into the ON (OPEN) position. See Fig. 5-2.
2. Move the choke lever (if equipped) all the way backward
into the choke position.
3. Standing behind the mower, squeeze the blade control
against upper handle. The choke will now begin to slowly
return to the off choke position after activating the blade
control. Therefore, quickly move onto step four below.
4. Holding these two handles together firmly, grasp recoil
starter handle and pull rope out with a rapid, continuous,
full arm stroke. See Fig. 5-2. Keeping a firm grip on the
starter handle let the rope rewind slowly. Repeat until
engine cranks. Let the rope rewind each time slowly.
Stopping Engine
1. Release blade control to stop the engine and blade.
WARNING: Wait for the blade to stop completely
before performing any work on the mower or to
remove the grass catcher.
f
Figure 5-1
f
Figure 5-2
UsingYourLawnMower
Be sure lawn is clear of stones, sticks, wire, or other objects
which could damage lawn mower or engine. Such objects could
be accidently thrown by the mower in any direction and cause
serious personal injury to the operator and others.
1. Once the engine is running, squeeze the drive control
against the upper handle to propel mower.
WARNING: The operation of any lawn mower can
result in foreign objects being thrown into the eyes,
which can damage your eyes severely. Always wear
safety glasses while operating the mower, or while
performing any adjustments or repairs on it.
UsingasMulcher
For mulching grass, remove the grass catcher and side discharge
chute from the mower. For effective mulching, do not cut wet
grass. If the grass has been allowed to grow in excess of four
inches, mulching is not recommended. Use the grass catcher to
bag clippings instead.
UsingGrassCatcher
You can use the grass catcher to collect clippings while you are
operating the mower.
1. Attach grass catcher following instructions in the
"Assembly & Set-Up" section. Grass clippings will
automatically collect in bag as you run mower. Operate
mower till grass bag is full.
2. Stop engine completely by releasing the blade control.
Make sure that the unit has come to a complete stop.
3. Lift discharge door and pull grass bag up and away from
the mower to remove the bag. Dispose of the grass
clippings and reinstall the bag when complete.
_ ARNING: If you strike a foreign object, stop the
engine. Remove wire from the spark plug,
thoroughly inspect mower for any damage, and
repair damage before restarting and operating.
Extensive vibration of mower during operation is an
indication of damage. The unit should be promptly
inspected and repaired.
SECTION 5 -- OPERATION 13
Maintenance&Adjustments
6
Maintenance
GeneralRecommendations
Always observe safety rules when performing any
maintenance.
The warranty on this lawn mower does not cover items that
have been subjected to operator abuse or negligence. To
receive full value from warranty, operator must maintain
the lawn mower as instructed here.
Changing of engine-governed speed will void engine
warranty.
All adjustments should be checked at least once each
season.
Periodically check all fasteners and make sure these are
tight.
A
Lubrication
WARNING: Always stop engine, disconnect spark
plug, and ground against engine before performing
any type of maintenance on your machine.
1. Lubricate pivot points on the blade and drive control at
least once a season with light oil. These controls must
operate freely in both directions. See Fig. 6-1.
2. Lubricate the wheels at least once a season with light oil (or
motor oil). If wheels are removed for any reason, lubricate
surface of the pivot arm and inner surface of the wheel
with light oil. See Fig. 6-1.
3. Lubricate the torsion spring and pivot points on the rear
discharge door and side mulch plug periodically with light
oil to prevent rust. See Fig. 6-1.
4. Follow the accompanying engine manual for lubrication
schedule and instruction for engine lubrication.
DeckCare
Clean underside of the mower deck after each use to prevent
build-up of grass clippings or other debris. Follow steps below
for this job.
1. Disconnect spark plug wire. Drain gasoline from lawn
mower or place a piece of plastic under the gas cap.
2. Tip mower so that it rests on the housing. Keep the side
with the air cleaner facing up. Hold mower firmly.
WARNING: Never tip the mower more than 90 ° in
any direction and do not leave the mower tipped for
any length of time. Oil can drain into the upper part
of the engine causing a starting problem.
3. Scrape and clean the underside of the deck with a suitable
tool. Do not spray with water.
IMPORTANT: Do not use a pressure washer or garden hose
to clean your unit. These may cause damage to bearings,
or the engine. The use of water will result in shortened life
and reduce serviceability.
4. Put the mower back on its wheels on the ground. If you
had put plastic under the gas cap earlier, make sure to
remove it now.
Figure 6-I
14
EngineCare
A list of key engine maintenance jobs required for good
performance by the mower is given below. Follow the
accompanying engine manual for a detailed list and instructions.
Maintain oil level as instructed in engine manual.
Service air cleaner every 25 hours under normal conditions.
Clean every few hours under extremely dusty conditions.
Poor engine performance and flooding usually indicates
that the air cleaner should be serviced. To service the air
cleaner, refer to the engine manual.
Clean spark plug and reset the gap once a season. Spark
plug replacement is recommended at the start of each
mowing season. Check engine manual for correct plug
type and gap specifications.
Clean engine regularly with a cloth or brush. Keep the
top of the engine clean to permit proper air circulation.
Remove all grass, dirt, and combustible debris from muffler
area.
ReplacingRearFlap
1. To remove rear flap, lift rear door, and press flap in on
either side to remove from hole. See Fig. 6-2.
r
..........!
/
2.
Figure 6-2
Remove flap from opposite hole and replace with new flap
in the opposite order and manner of removal.
SECTION 6 -- MAINTENANCE & ADJUSTMENTS 15
Service
7
8lade Care
WARNING: When removing the cutting blade for
sharpening or replacement, protect your hands with
a pair of heavy gloves or use a heavy rag to hold the
blade.
Periodically inspect the blade adapter for cracks, especially if you
strike a foreign object. Replace when necessary. Follow the steps
below for blade service.
1. Disconnect spark plug boot from spark plug. Turn mower
on its side making sure that the air filter and the carburetor
are facing up.
2. Remove the bolt and the blade bell support which hold the
blade and the blade adapter to the engine crankshaft. See
Fig. 7-1.
/
Blade Bell/
Support
4.
Remove blade from the adapter for testing balance.
Balance the blade on a round shaft screwdriver to check.
Remove metal from the heavy side until it balances evenly.
When sharpening the blade, follow the original angle of
grind. Grind each cutting edge equally to keep the blade
balanced.
_ll WARNING: An unbalanced blade will cause
excessive vibration when rotating at high speeds. It
may cause damage to mower and could break
causing personal injury.
5. Lubricate the engine crankshaft and the inner surface of
the blade adapter with light oil. Slide the blade adapter
onto the engine crankshaft. Place the blade on the adapter
such that the side of the blade marked "Bottom" (or with
part number) faces the ground when the mower is in the
operating position. Make sure that the blade is aligned and
seated on the blade adapter flanges.
6. Place blade bell support on the blade. Align notches on the
blade bell support with small holes in blade.
7. Replace hex bolt and tighten hex bolt to torque: 450 in. Ibs.
rain., 600 in. Ibs. max.
To ensure safe operation of your mower, periodically check the
blade bolt for correct torque.
3.
Figure 7=1
Remove blade and adapter from the crankshaft. See Fig.
7-1.
NOTE:When removing these items on units with the
Honda engine, the pulleys and washers may also break
free from the crankshaft. Be sure to make note of the
orientation of these items for reassembly.
16
Belt Care
1.
Remove two shoulder screws securing front drive cover to
mower deck. See Figure 7-2. Press inward on sides of front
drive cover and release tabs that secure it to the height
adjuster brackets. Remove drive cover from mower.
\\
Figure 7-2
2. Loosen screw holding belt tension spring to transmission.
See Figure 7-2 inset. Do not remove screw completely. As
you loosen it, tension on the belt will be released.
3. Push transmission up a little and slide belt off the
transmission pulley. Lift mower to access belt from
underside of mower. Slide belt off of engine pulley and
around the blade. See Figure 7-3.
4. Replace with new belt, working around blade. Make sure
belt isfirmly seated on engine pulley while pulling from
the other side and sliding it around the transmission pulley.
Tighten screw loosened earlier to secure belt tension
spring to the transmission.
S. Reassemble front drive cover.
0ff-SeasonStorage
The following steps should be taken to prepare your lawn mower
for storage.
Clean and lubricate mower thoroughly as described in the
lubrication instructions.
Do not use apressure washer or garden hose to clean your
unit.
Coat mower's cutting blade with chassis grease to prevent
rusting.
Refer to engine manual for correct engine storage
instructions.
Store mower in a dry, clean area. Do not store next to
corrosive materials, such as fertilizer.
When storing any type of power equipment in a poorly
ventilated or metal storage shed, care should be taken to
rust-proof the equipment. Using a light oil or silicone, coat the
equipment, especially cables and all moving parts of your lawn
mower before storage.
Figure 7-3
SECTION7 -- SERVICE 17
Troubleshooting
Problem
Engine Fails to start
Engine runs erratic
1.
2.
3.
4.
Cause
Blade control disengaged. 1.
Spark plug boot disconnected. 2.
Fuel tank empty or stale fuel. 3.
Engine not primed (if equipped with primer). 4.
Remedy
Engage blade control.
Connect wire to spark boot.
Fill tank with clean, fresh gasoline.
Prime engine as instructed in the Operation
section.
5. Faulty spark plug.
6. Blocked fuel line.
7. Engine flooded.
8. Fuel valve (if equipped) closed.
5. Clean, adjust gap, or replace.
6. Clean fuel line.
7. Walta few minutes to restart, but do not
prime.
8. Open fuel valve. See engine manual.
9. Engine not choked (if equipped with choke).
1&Burnt fuse. (Electric Start only)
1. Spark plug boot loose.
2. Blocked fuel line or stale fuel.
3.
4.
5.
6.
Vent in gas cap plugged.
Water or dirt in fuel system.
Dirty air cleaner.
Unit running with CHOKE (if equipped)
applied.
Engine oil level low.
Air flow restricted.
Spark plug gap too close.
9. Choke engine. See engine manual.
10.Replace fuse (see Service Section).
1. Connectand tighten spark plug boot.
2. Clean fuel line; fill tank with clean, fresh
gasoline.
3. Clear vent.
4. Drain fuel tank. Refill with fresh fuel.
5. Referto engine manual.
6. Push CHOKE knob in.
Engine overheats 1. 1. Fill crankcase with proper oil.
2. 2. Clean area around and on top of engine.
Occasional skips 1. 1. Adjust gap to .030".
(hesitates) at
high speed
Idles poorly 1. Spark plug fouled, faulty, or gap too wide. 1.
2. D_rty air cleaner. 2.
Excesstve Vibration 1. Cutting blade loose or unbalanced. 1.
2. Bent cutting blade. 2.
Mower will not 1. Wet grass. 1.
mulch grass
2.
3.
2. Excessively high grass.
3. Dull blade.
Reset gap to .030" or replace spark plug.
Refer to engine manual.
Tighten blade and adapter. Balance blade.
See an authorized service dealer.
Do not mow when grass is wet; wait until
later to cut.
Mow once at a high cutting height, then
mow again at desired height or make a
narrower cutting path.
Sharpen or replace blade.
Continued on next page
Troubleshooting
Problem
Cause Remedy
Uneven cut 1. Wheels not positioned correctly. 1. Place all fourwheels in same height position
(if equipped with individual height adjusters).
2. Dull blade. 2. Sharpen or replace blade.
19
ModelSeries560
16
\
,4
17
19
ii 46
[]
47
35
9
Wheel Treads
ZagTread Bar Tread
74
NOTE: Mower features/components vary by model. NOT all parts pictured above and listed on the following pages are
standard equipment.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24

MTD 12A-569Q795 Owner's manual

Category
Lawnmowers
Type
Owner's manual

MTD 12A-569Q795 is a self-propelled lawnmower engineered to provide excellent performance when properly operated and maintained. It's a precision piece of power equipment, capable of mowing grass and helping you keep your lawn looking neat and tidy. To ensure safe and efficient operation, be sure to read and understand the instructions provided in the operator's manual before using the machine.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI