Installation
Instructions
Overthe Range
Microwave Oven
Questions?Call800.GE.CARES(800.432.2737)or Visit,,,, x_ebsite;,t:Hotpointcom I
BEFORE YOU BEGIN
Read these instructions completely and carefully.
• IMPORTANT - S_,,e_hese
instructions for local inspector's use.
• IMPORTANT - Obse,,e;,ll
goxernin(, codes and ordinances.
• Note to Installer - Be sure to leaxe these
instructions with the (_onsumer.
o
o
o
o
Note to Consumer - Keep these
instructions for futm'e reterence.
Skill level - Installation of this appliance requires
basic mechanical and electrical skills.
Proper installation is the responsibility of the installer.
Product thihu'e due to improper installation is not
coxered trader the _4arrantx.
Fora Spanishversionof thismanual, visitour Websiteat Hotpoint.com.
Para consultaruna versionen espafiolde estemanual de instrucciones,visitenuestrositio
de internetHotpointcom.
READ CAREFULLY.
KEEP THESE INSTRUCTIONS.
Installation Instructions
CONTENTS
General information
Important Safety Instructions .................................. 3
Electrical Requirements .......................................... 3
Hood Exhaust ....................................... 4, 5
Damage--Shipment/Installation .............................. 6
Parts Included. ......................................... 6
Tools You Will Need ............................................... 7
Mounting Space ...................................................... 7
Step-by-step installation guide
Placement of Mounting Plate ............................ 8-10
Removing tire Mounting Plate ...................... 8
Finding the _4all Studs ................................. 8
Determining _all Plate Loration .................. 9
Detemiiuiug Rear Mortaring Screw Locations .. 10
Installation Types .................................. 11-22
[] ()utside Top ............................
Exhaust
12-14
Attach Mounting Plate to _4_dl ....... 12
Prepalzlfion of Top Cabinet .......... 13
Install the Damper .................. 13
Mount the Microwave Oven ........ 13, 14
At!just the Exhaust Adaptor .......... 14
Connecting Durt_x)rk .......................... 14
_ Outside Back Exhaust 15-18
Preparing Rear _4all for
Outside Back Exhaust .......................... 15
Remove Exhaust Adaptor .................... 15
Attach Mounting Plate to _4"dl ....... 16
Prepa_lfion of Top Cabinet .......... 16
Adapting Microwave glower
ti)r Outside Back Exhaust ................ 16, 17
Mount the Microwave Oven .......... 18
_] Redrculating ........................................ 19-22
Attach Mounting Plate to _'dl ....... 19
Preparation of Top Cabinet .......... 19
Adapting Microwave glower
for Redrrulation ......................... 20, 21
Mount the Microwave Oveu .......... 21, 22
Installing the
Charcoal Filter Accessory .................... 22
Before You Use Your Microwave .......................... 23
2
Installation Instructions
IMPORTANT SAFETY INSTRUCTIONS
This product requires a three-l)rong, ,gr°unded outlet.
The installer must perform a ground continuit _, check
on the power outlet box before begilming the
installation to insure that the outlet box is properly
grotmded. If not prol_erly grounded, or if the outlet
box does n(>t meet electrical requirements n(>ted
(trader EI,ECTRI(_AI, REQ/_.IIREMENTS), a qualified
electrMan sh()uld be employed t() correct am
deficiencies.
I!1//11/ l
CAUTION: For persona]
safety, remove house fuse
or open circuit breaker
before beghulhag
installation to avoid severe
or fatal shock injury.
CAUTION: For persona] safety, the momathag surface
must be capable of supporting the cabinet load, hi
addition to the added weight of this 63-85 pomad
product, plus additional oven loads of up to 50 pomads
or a total weight of 113-135 pounds.
CAUTION: For personal safety, this product cmmot
be installed hi cabinet arrmagements such as an islmad or
a peninsula. It must be momated to BOTH a top cabinet
AND a wall.
NOTE: For easier installation mad personal safety, it is
recmmnended that two people install this product.
IMPORTANT - PLEASE RILM) CAREFULLY. FOR
PERSONAL SAFETY, THIS APPLIANCE MUST BE
PROPERLY GROUNDED TO AVOID SEVERE OR
FATAL SHOCK.
The power cord of this
appfimace is equipped with
a three-prong (gromadhag)
plug which mates with a
sta_adaJ_d three-prong
(gromadhag) wall receptacle
to mh_hnize the possibility
of electric shock hazard
from this appliance.
Ensure proper
ground exists
before use
You should have the wall receptacle mad circuit checked
by a qualified electricima to make sure the receptacle is
properly gromaded.
Where a staaadaaxi two-prong wall receptacle is
encountered, it is very hnportant to have it replaced
with a properly gromaded three-prong wall receptacle,
installed by a qualified electridma.
DO NOT, UNDER ANY CIRCUMSTANCES, CUT,
DI_)'ORM OR REMOVE ANY OF THI: PRONGS
FROM THE POWER CORD. DO NOT USE WITH
AN KXTENSION CORD.
ELECTRICAL
REQUIREMENTS
Product rating is 120 volts AC, 60 Hertz, 15 amps and
1.58 kilowatts. This product must be connected to a
supply circuit of tile i_roper voltage and ti'equei_cy.
Wire size inust conlorin to tile requireu/ei_ts of tile
National Electrical Code or tile prevailing local
code ti)r this kilowatt rating. Tile power supply
cord and I)lug should be brought to a separate
15- t() 20-alni_ere branch circuit single gi'ounded
outlet. The outlet box should be located in the
cabinet above tile u_icrowave oven. Tile outlet box
and supply circuit should be installed by a qualified
electrician and conform to the National Electrical
Code or the prewfiling local code.
3
Installation Instructions
HOOD EXHAUST
NOTE: Read these next two pages only if you plml to vent your exhaust to the
outside. If you plan to recirculate the air back into the room, proceed to page 6.
OUTSIDE TOP EXHAUST (EXAMPLE ONLY)
The following chart describes an example ot one possible
ductwork installation.
DUCT PIECES
EQUIVALENT NUMBER
LENGTH x USED
RoofCap 24 Ft. x
12Ft.StraightDuct 12Ft. x
(6" Round)
" Rectangular-to-Round 5Ft. x
TransitionAdaptor*
Equivalentlengthsofduct piecesare basedon actualtests and
reflectrequirementsfor goodventingperformancewith anyventhood.
(1)
(1)
(1)
Total Length
EQUIVALENT
LENGTH
24 Ft.
12Ft.
5Ft.
41 Ft.
* IMPORTANT: If a rectangula>to-round transition adaptor is used, the bottom cornet_ of the damper
will haxe to be cut to fit, usino._ the tin snips, in order to allow free moxement of the damper.
OUTSIDE BACK EXHAUST (EXAMPLE ONLY)
The following chart describes an example ot one possible
ductwork installation.
EQUIVALENT
DUCT PIECES LENGTH* x
Wall Cap 40Ft.
3 Ft.StraightDuct 3 Ft. x
3W' x 10"Rectangular)
(_ 90° Elbow 10Ft. x
NUMBER EQUIVALENT
USED = LENGTH
x (1) 40Ft.
(1) 3 Ft.
(2) 20R.
Equivalent lengths of duct pieces are based on actual tests and
reflect requirements for good venting performance with any vent hood.
Total Length = 63 Ft.
NOTE: For back exhaust, care should be taken to align exhaust with space between studs, or wall should be prepared
at the time it is const_ ucted by leaving enough space between the wall studs to accommodate exhaust.
4
Installation Instructions
NOTE: If wm need to install ducts, note that the total
duct lengti_ of 3V_" x 10" rectangular or 6" diameter
round duct should not exceed 140 equivalent feet.
Outside ventilation requires a HOOD EXHALIST DLICT.
Read the following careflfllv.
NOTE: It is important that venting be installed using
the most direct route and with as tew elbows as possible.
This ensures clear venting of exhaust and helps prevent
blockages. Also, make sure dmnpers swing freely and
nothing is blocking the ducts.
Exhaust connection:
The hood exhaust has been designed to mate with
a standard 3V_" x 10" rectangular duct.
If a round duct is required, a rectangulai_to-round
transition adaptor m ust be used. Do not use less than
a 6" diameter duct.
Maximum duct length:
For satisfi_ctorv air movement, the total duct length of
3¼" x ] 0" rectangular or 6" diameter round duct should
not exceed 140 equivalent feet,
Elbows, transitions, wall and roof caps,
etc., present additional resistance to airflow and are
equiwdent to a section of straight duct which is longer
than their actual physical size, When calculating the total
duct length, add the equiwdent lengths of all transitions
and adaptors plus the length of all straight duct sections,
The chart below shows wm how to calculate total
equiwdent ductwork length using the approximate feet
of equiwdent length of some typical ducts,
EQUIVALENT NUMBER EQUIVALENT
DUCT PIECES LENGTH x USED = LENGTH
Rectangular-to-Round 5Ft. x ( ) = Ft.
TransitionAdaptor*
Wall Cap 40 Ft. x ( ) = Ft.
C)_ 90° Elbow 10Ft. x ( ) = Ft.
45° Elbow 5Ft. x ( ) = Ft.
90° Elbow 25 Ft. x ( ) = Ft.
45° Elbow 5Ft. x ( ) = Ft.
RoofCap 24 Ft. x ( ) = Ft.
StraightDuct6" Roundor 1Ft. x ( ) = Ft.
3W' x 10"Rectangular
Total Ductwork = Ft.
* IMPORTANT: If' a r(<tangulal_to-round transition Equival( nl 1(ngths o_ du<t pie(( s are bas(d on aclual lests
adapt(n- is us(d, th( bottom (omers of th( damp(l and ret]( (t re(lt/il-( m( IllS ik)F good v( llling l)erfonnan( ( with
,,'.illhave to Ix (:Ill to fit, u'dng th( lin snips, in or&l any vent hood.
to allow ['lee lllOVel)lel]l of Ihe (]Hlllpel.
5
Installation Instructions
DAMAGE--SHIPMENT/
INSTALLATION
" If the unit is damaged in shipment, return the
unit to the store in which it was bought fin" repair
oI" i'ei)la ceu/enL
" If the unit is dainaged by the customer, repair or
replacement is the responsibility of the customer.
• If the unit is damaged by the installer (if other
than the customer), repair or replacement must
be made by arrangement between customer
and installer.
PARTS INCLUDED
HARDWARE PACKET
PART QUANTITY
WoodScrews 1
(74"x2")
ToggleBolts(and 3
wingnuts)(_6" x3")
Self-AligningMachine 3
Screws(W'-28x 3W')
NylonGrommet 2
(formetalcabinets)
You will find the installation hardware contained in
a packet with the trait. Check to make stlre w)tl have
all these parts.
NOTE: Some extra parts are included.
ADDITIONAL PARTS
PART
TOP CABINETTEMPLATE
REAR
WALL
TEMPLATE
F
INSTRUCTIONS
TopCabinet
Template
RearWall
Template
Installation
Instructions
Separately
Packed
Grease
Filter
Separately
Packed
Exhaust
Adaptor
QUANTITY
1
6
Installation Instructions
TOOLS YOU WILL NEED
# 1 and#2Phillipsscrewdriver
Tinsnips(forcutting
damper,if required)
Gloves
Safety goggles
Pencil
Rulerortape measure and
tedge
Scissors
(to cut template, if necessary)
Electric drill with ¾_", V/" and %"
drill bits
Saw (saber, hole or keyhole)
0
Stud finder or
Hammer (optional)
Level
Carpenter square
(optional)
Fillerblocksor scrap
woodpieces,if needed
fortop cabinetspacing
(usedonrecessedbottom
cabinetinstallationsonly)
Duct and masking tape
MOUNTING SPACE
Backsplash
66" or More
fromthe Floor
tothe Topof
the Microwave
\
BottomEdgeof
CabinetNeedsto
be30" or More
from theCooking
Surface
NOTES:
• The space between the cabinets must be
30" wide and fl'ee of obstructions.
• If the space between the cabinets is greater
than 30", a Filler Panel Kit may be used to fill
in the gap between the microwave oven and
the cabinets. Your Owner's Manual contains
the kit nmnber for w)m" model.
• This microwave oven is Ira" installation over
ranges up to 36" wide.
• When installing the microwave oven beneath
smooth, flat cabinets, be careful to follow the
instructions on the top cabinet template for
power cord clearmlce.
7
Installation Instructions
PLACEMENT OF THE MOUNTING PLATE
REMOVING THE MICROWAVE
OVEN FROM THE CARTON/
REMOVING THE MOUNTING PLATE
[]Remove tile installation instructions, filter, glass
tray the exhaust adaptor and the small hardware
bag,. Do not remo_e tile Styrofoam I)r°tecting, tile
front of tile o_,en,
_Fold back all 4 carton flaps full) against carton
sides. Then careflflE roll the oxen and carton oxer
onto tile top side. T'he oxen should be restin,*._ in
tile Stx roflmm.
Styrofoam
[]Pull tile carton up and off tile oven.
[] Remove and properly discard plastic bags.
._.._'MM Screws
0unting Plate 1
_ Remove tile 2 screws from tile bottom mounting
plate. Remoxe tile mounting plate and set aside.
This plate will be used with the rear wall template
for mo/mting. REPLACE THE SCREWS.
I-_ FINDING THE WALL STUDS
i
]Find tile studs, usino one of tile following
methods:
Wall
Studs
i
A. Stud finder--a magnetic device that
locates nails.
OR
B. Use a hammer to tap lightly across tile
mo/mting sm'face to find a solid so/md.
This will indicate a stud location.
_ After tile find tile bvlocating stud(s),
center
probing tile wall with a small nail to find tile edges
of tile stud, Then place a mark hallway between
tile edges, Tile center of any a(!jacent studs should
be 16" or 24" fl'om this mark.
_Draw a line down the center of the studs,
THE MICROWAVE MUST BE CONNECTED TO
AT LE&ST ONE WALL STUD,
8
Installation Instructions
DETERMINING WALL PLATE LOCATION UNDER YOUR CABINET
Template beneath cabinet
with flat bottom
Template beneath cabinet
with recessed bottom
Trimthe rearwall
templatealong
the dotted line.
II
I)raw averticalline onthe wall at
the centerof the 30" to36" wide
space.Tapethe RearWall Template
onto the wall matching the
centerline andtouchingthe bottom
of thecabinet.
Template aligned with front overhang
on cabinet bottom
Drawaline onthe
backwall equaltothe
depthof the front
overhang.Trimthe
rearwall template
alongthe dottedline.
........................ii
Trimthe rearwall ...........
templatealong
thedotted line.
Drawaverticallineonthe wall at
thecenterof the 30"or 36" space.
Tapethe RearWallTemplateonto
thewall matchingthe centerlineand
touchingthebottomcabinetframe.
I
THE MICROWAVE MUST BE LEVEL. [
I
Use a lexel to make sure the cabinet bottom is lexel.
Your cabinets may have decorative trim that interieres
with the microwave installation, Remove the decorative
trim to install the microwave i)roperly and to make it
level.
On cabinets with a fl'ont overhang, draw a line on the
back wall at the same depth as the overhang. _Mign the
template to match overhang depth. This will kee I) the
microwave level.
[]Measure the inside depth of the fl'ont overhang.
[]Draw a horizontal line on the back wall to match
the depth of the fl'ont ovefl_ang. See illustration.
[]Draw a vertical line on the wall at the center of the
30" to 36" space. Trim the template on the dotted line.
Tape the Rear Will Template to the wall using the
marked centefline and top line as a guide.
9
Installation Instructions
DETERMINING REAR MOUNTING SCREW LOCATIONS
..........................._-_ ..........................................................................................._._ ...............................................................................................................................
= .........
REAR WALl TEMPLATE
.
o o o o o o o o o o o o o&o o o o o o o o o o o o o _
,_ _ o^o o o o _ o o ,_ o o o _ o o^o o _E_ E_2_
CAUTION: _,_ar glo_es
to axoid cutting finge_
on shal]_ edges.
NOTE: The P.ear %'all Template serves
to position the bottom motmting, I_late and
to locate the horizontnl exhaust outlet.
_ljse a level to check that the template is positioned
a cct H'atelv.
_ I,ocate and mark at least one stud on the lefi or right
side of the centerline. It is importnnt to use at least one
wood screw mounted firmly in a stud to support the
weight of the microwave.
Mark three additional, evenly spaced locations for the
supplied toggle bolts.
_ Drill in If is a stud,
holes the ulai'ked locations, there
drill a _A_" hole fi)r wood screws. For holes that don't
line up with a stud, drill a :'A" hole fi)r toggle bolts.
NOTE: DO NOT MOUNT THE PLATE AT THIS TIME.
10
Installation Instructions
INSTALLATION TYPES
This microwave ()veil is designed fi)r adaptation to
the following three types of ventilation:
A, Outside Top Exhaust (Vertical Duct)
B, Outside Back Exhaust (Horizontal Duct)
C, Recirculating (Non-Vented Ductless)
(Choose A, B or C)
NOTE: This microwave is shii)ped assembled fl)r Outside
Top Exhaust (except fl)r non-vented models), Select the
Wpe of ventilation required for wmr installation and
proceed to that section,
OUTSIDE TOP EXHAUST
(VERTICAL DUCT)
OUTSIDE BACK EXHAUST
(HORIZONTAL DUCT)
1
_-_ RECIRCULATING
(NON-VENTED DUCTLESS)
A Charcoal Filter Accessory
Kit is required fi)r tile non-
vented exhaust. (See your
Owner's Manual tot the kit
number.)
11
Installation Instructions
OUTSIDE TOP EXHAUST (Vertical Duct)
INSTALLATION OVERVIEW
A1. Attach Mounting Plate to _'fll
A2. Prepare Top Cabinet
A3. Check Damper Operation
A4. Mount Microwave Oven
A5. Ac!j ust Exhaust Adaptor
A6. (_onnect Ductwork
I-_ ATTACH THE MOUNTING
PLATE TO THE WALL
Remove the template fl'om the rear wall. The
motmting plate must be secured to the wall using at
least 3 toggle bolts and one wood screw. The wood
screw must engage a wall stud.
[]Remove the toggle wings fl'om the bolts.
[]Insert the bolts into the mounting plate
through the holes designated to go into drywall
and reattach the toggle wings to '_A" onto each bolt.
To use toggle bolts:
Mounting
Plate
I_1,1
SpacingforToggles
MoreThanWall
-,,,-I_,-,.-!._Thickness
ToggleWings
B01tEnd
_ Place the motmting plate against the wall and
insert the toggle wings into the holes in the wall
to motmt the plate.
NOTE: Betm'e tightening the toggle bolts and the
wood screw(s), check again to be sure that the
mounting plate is level and centered leti to right.
CAUTION: Be careflfl to avoid pinching fingers
between the back of the motmting plate and the wall.
_ Tighten all bolts. Pull the plate away fl'om the
wall to hel I) tighten the bolts. Be careflfl not to
ove>torque the toggle bolts.
12
Installation Instructions
I-_ USE TOP CABINET TEMPLATE
FOR PREPARATION OF TOP
CABINET
Tile top cabinet template will help you locate tile top
support screw holes, power cord and exhaust outlet
locations.
" Read tile instructions on tile TOP CABINET
TEMPLATE.
" Tape it tmderneath tile top cabinet.
" Drill tile holes, fi_llowing tile instructions on tile
TOP CABINET TEMPLATE.
CAUTION: _'_ear satiety o-oo-des when drillim, holes
in tile cabinet bottom.
INSTALL THE DAMPER
Remove rear
retaining screw
" Place tile microwaxe in its upright position.
" Remoxe tile retaining screw at tile rear of tile
I/lOtOI" doo I'.
" I,ifl tile blower motor door.
" Slide tile exhaust adaptor toward tile lett side and
into tile opening.
" Tile adaptor should be oriented as shown.
I-_ INSTALL THE DAMPER (cont.)
Renstarear
_ retainingscrew
" Close tile blower cover with adaptor and reinstall
I'ea I" scYew.
" Remove tape holding the damper. The damper
should pivot easily.
" Tile adaptor can be a(!justed, lett to right and fl'ont
to back, to align with the house exhaust ductwork.
13
r_ MOUNT THE MICROWAVE OVEN
FOR EASIER INSTAI,IATION AND PERSONAl,
SAFETY, X,_E RECOMMEND THAT TWO PEOPLE
INSTALL THIS MICROWAVE OVEN.
NOTE: If yore" cabinet is metal, use tile nylon
grommet aro/md tile power cord hole to prevent
cutting of tile cord.
NOTE: We recommend using filler blocks if tile
cabinet front hangs below tile cabinet bottom shelf.
IMPORTANT: If filler blocks are
not used, case damage may occur from
overtightening screws.
NOTE: When mo/mting
tile illicrowave oven_
thread power cord
through hole in bottom of
top cabinet. Keep it tight
throughout Steps 1-3. Do
not pinch cord or lift
oven by pulling
_I,ifl microwave, tilt
it fl_rward and hook
slots at back bottom
edge onto flmr lower
tabs of mounting
plate.
_ Rotate front of
oxen
up against cabinet
bottolIl.
Installation Instructions
I-_ MOUNT THE MICROWAVE
OVEN (cont.)
[]Insert a self:aligning screw through top center
cabinet hole. Temporarily secure the oven by
turning the screw at least two full turns alter the
threads have engaged. (It will be completely
tightened later.) Be sure to keep power cord tight,
Be careful not to pinch the cord, especially when
mounting flush to bottom of cabinet.
Cabinet Front
Cabinet Bottom Shelf
FillerBlock
T quivalent
toDepth
ofCabinet
Recess
Self-AligningScrew
Microwave OvenTop
[] Insert 2 self:aligning screws
through outer top cabinet
holes. Turn two flfll tm'ns on
each screw.
Tighten
center
screw
completely.
[] Tighten the outer two screws to the top of the
microwave oxen. (X,\ hile tiohtening screws, hold
the microwaxe oxen in place against the wall and
the top cabinet.)
/
_ Install grease filter: See the Owner's Manual
packed with the microwaxe.
4
ADJUST THE EXHAUST
ADAPTOR
Open the top cabinet and ac!iust the exhaust adaptor
to connect to the house duct.
Damper
J
For Front-to-Back or
Side-to-Side Adjustment,
Slide the Exhaust
Adaptor as Needed
I-_ CONNECTING DUCTWORK
House Duct
_ Extend the house duct down to connect to
the exhaust adaptor.
] . , duct tape.
Seal exhaust duct ioints using
Installation Instructions
OUTSIDE BACK EXHAUST (Horizontal Duct)
INSTALLATION OVERVIEW
B1. Prepare Rear _4'all
B2. Remove Exhaust Adaptor
B3. Attach Mounting Plate to _'all
B4. Prepare Top Cabinet
B5, Adapt Blower tot Back Exhaust
B6, Motmt the Microwave Oven
PREPARING THE REAR WALL
FOR OUTSIDE BACK EXHAUST
The rear wall template should be positioned accm'atel)
as shown on page 9.
" Read the instructions on the REAR _4_I,I,
TEMPI ,ATE.
• Grit the oi_enin_, ti)llowing, the instHictions of the
REAR WAI,I, TEMPI,ATE.
15
Installation Instructions
I-_ ATTACH THE MOUNTING
PLATE TO THE WALL
Remove the template fl'om the rear wall. The
mounting plate must be secured to tile wall using at
least 3 toggle bolts and one wood screw. Tile wood
screw must engage a wall stud,
[]Remove tile toggle wings fl'om tile bolts.
_ Insert tile bolts into tile mounting plate through
the holes designated to go into drywall and reattach
the toggle wings to :_A"onto each bolt.
To use toggle bolts:
Mounting
Plate
Spacingfor TogglesMore
+l-.H.-i-.,_ ThanWall Thickness
i
ToggleWings
B01tEnd
[]Place the too/rating plate against the wall and
insert the toggle wings into the holes in the wall
to mount the plate.
NOTE: gefln'e tightening the toggle bolts and the
wood screw(s), check again to be sure that tile
mo/mting plate is level and centered left to right.
CAUTION: Be carefifl to awfid pinching fingers
between the back of the mo/mting plate and the wall.
_ Tighten all bolts. Pull the plate away fl'om the
wall to hel I) tighten the bolts. Be carefifl not to
ove_=torque the toggle bolts.
USE TOP CABINET TEMPLATE
FOR PREPARATION OF TOP
CABINET
Tile top cabinet template will hel I) you locate tile top
S/ll)l)oI't scI'ew holes and l)oweI" coi'd Ctlto/lt,
• Read the instructions on the TOP CABINET
TEMPI,ATE.
" Tape it tmderneath tile top cabinet.
" Drill the holes, following the instructions on the
TOP CABINET TEMPLATE.
CAUTION: Wear safety goggles when drilling holes
in tile cabinet bottom.
ADAPTING MICROWAVE
BLOWER FOR OUTSIDE
BACK EXHAUST
[] RelllOXe tile back top center blower illotoF dooF
retaining screw.
of
iMicrowave
BlowerDoor
Screw
_] Open tile blower door it tile backlifting /l I)
at
side of the microwaxe. Remo_e and saxe the top
and back retaining screws that hold the blower
iilotoi" ill tile iilicFowa',e,
Retaining
screw
Retaining
screw
16
Installation Instructions
ADAPTING MICROWAVE
BLOWER FOR OUTSIDE
BACK EXHAUST (cont.)
[] Carefllllv slide the blower motor toward the
right,
and lift it partially out of the opening. Note: The
blower wires are long enough to allow flexible
handling while perfimning these steps. Disconnect
the wires only if it is necessary fi_r additional
flexibility.
Backof
Microwave
[] Remoxe the two screws holding the gray-colored
inlet sleexe to the blower trait. Rotate the gray
slee;e as shown until the gray arrow lines up with
the "g', back exhaust. Reinstall the two screws.
Remove screws from
Gray Inlet Sleeve _,.
/
,%,- i'
/ / j-
Back of Microwave
_Roll the assembled blower unit so that the
black-colored exhaust outlet laces the back of
the microwave and the gray-colored inlet sleeve
laces downward. NOTE: The gray-colored sleeve
opening must AI._,_&_VS face downward to ensure
proper operation of the microwave.
MustFace
Downward
Black
Exhaust
Outlet
Backof
Microwave
] Tilt and the blower trait back into theplace
oi_ening, in the top of the microwaxe.
CAUTION: Do not pull or stretch the blower
unit wiring. Make sure the wires are not
pinched.
_ Secure the blower trait to the microwaxe with
the two screws remoxed in Step 2.
Retaining
screw
Retaining
screw
[] Close the blower coxer.
[]Attach the exhaust adaptor to the rear of the
microwaxe b) sliding it into the guides at the
top center of the back of the oxen.
Adaptor
Backof
Microwave
Guide
Guide
BlowerMotor Screw
LockingTabs
Push in securely until it is in the lower locking
tabs. Take care to assure that the damper hinge
is installed so that it is at the top and that the
damper swings fl'eelv. Reinstall the original
blower motor screw through the adaptor and
into the back of the microwave.
17
Installation Instructions
MOUNT THE MICROWAVE
OVEN
FOR EASIER INSTAI,IATION AND PERSONAI,
SAFETY, WE RECOMMEND THAT TWO PEOPLE
INSTALL THIS MICROWAVE OVEN.
NOTE: If vour cabinet is metal, use tile nylon
grommet around tile power cord hole to prevent
cutting of tile cord.
NOTE: We recommend using filler blocks if the
cabinet fl'ont hangs below the cabinet bottom shelf.
IMPORTANT: If filler blocks are
not used, case damage may occur from
overtightening screws.
NOTE: When motmting
tile inicFowave oven_
thread power cord
through hole in bottom of
top cabinet. Kee I) it tight
throughout Steps 1-3. Do
not pinch cord or lift
oven b)' pulling cord.
[]I,ifl microwave, tilt
it forward and hook
slots at back bottom
edge ()lit() tO/ll" lower
tabs of motmting
plate.
_ Rotate front of
o_en
up against cabinet
bottom.
_lnsert a self=aligning screw through top center
cabinet hole. Temporarily secure tile oven by
turning tile screw at least two full turns atter tile
threads have engaged. (It will be completely
tightened later.) Be sure to keep power cord
tight. Be careful not to pinch the cord, especially
when mounting flush to Bottom of cabinet.
CabinetFront
CabinetBottomShelf
FillerBlock
T quivalent
to Depth
of Cabinet
Recess
Self-AligningScrew
MicrowaveOvenTop
_lnsert 2 self-aligning screws
throm,h_ outer top cabinet
holes. Tm'n two flfll tm'ns
on each screw.
_ Tighten center
screw completely,
[] Tighten the outer two screws to the top of the
microwave oven, (While tightening screws, hold
the microwave oven in place against the wall and
tile top cabinet.)
I
S /
_lnstall filter. See tile Owner Manualgrease
packed with tile microwaxe.
18
Installation Instructions
RECIRCULATING (Non-VentedDuctless)
INSTALLATION OVERVIEW
C1. Attach Mom_ting Plate to _11
C2. Prepare Top Cabinet
C3. Check Microwave Assembly
C4. Adapt Blower tin _Recirculation
C5. Mount the Microwave Oven
C6. Install Charcoal Filter
I-_ ATTACH THE MOUNTING
PLATE TO THE WALL
J
1 I
Remove the template fl'om the rear wall. The
mounting plate must be secured to the wall using
at least 3 toggle bolts and one wood screw. The
wood screw must engage a wall stud.
[]Remove the toggle wings from the bolts.
[]Insert the bolts into the mounting plate through
the holes designated to go into drywall and
reattach the toggle wings to _g" onto each bolt.
To use toggle bolts:
Spacing for Toggles
More Than Wall
+l_[.._Th ckness
ToggleWings
Mounting
Plate_
,,i,
BoltEnd
_ Place the motmting plate against the wall and
insert the toggle wings into the holes in the wall
to mount the plate.
NOTE: Before tightening the toggle bolts and the
wood screw(s), check again to be sure that the
motmting plate is level and centered left to right.
CAUTION: Be carefld to avoid pinching fingers
between the back of the motmting plate and the wall.
_ Tighten all bolts, Pull the plate awa)' fl'om the
wall to help tighten the bolts, Be careflfl not to
ove>torque toggle bolts.
USE TOP CABINET TEMPLATE
FOR PREPARATION OF TOP
CABINET
The top cabinet template will hel I) )ou locate the top
StlppoI't SCI'eW holes and powei" coi'd ct/totlt locations.
" Read the instructions on the TOP CABINET
TEMPI,ATE.
" Tape it tmderneath the top cabinet.
• Drill the holes, following the instructions on the
TOP CABINET TEMPLATE,
CAUTION: X4ear safet) goggles when drilling holes
in the cabinet bottom.
19
Installation Instructions
ADAPTING MICROWAVE
BLOWER FOR RECIRCULATION
_ RelllO_e tile back top center blower illOtoF (]ooI"
retaining screw.
J
Blower Motor-- Backof
Microwave
BlowerDoor
Screw
_Open the blower door b) lifting it up at the back
side of the microwaxe, Remo'_e and saxe the top
and back retaining screws that hold the blower
IllOtoI" in the illiCi'Owa_e,
Retaining
screw
Retaining
screw
_ Carefiflly slide the blower motor toward the right,
and lift it partially out of the opening. Note: The
blower wires are long enough to allow flexible
handling while perfimning these steps, Discmmect
the wires OlflV if it is necessary fl)i" additional
flexibility,
Backof
Microwave
_ Remo_e the two screws holding the o-ra_ colored
inlet sleeve to the blower unit, Rotate the gra)
slee'_e as shown tmtil the _ora_, arrow lines up with
the "R", Recirculating exhaust. Reinstall the two
scYews.
Remove screws from
Gray Inlet Sleeve XxJ_
_Roll the assembled blower trait so that the
black-colored exhaust outlet faces the fl'ont of
the microwave and the gra)_colored inlet sleeve
taces downward,
o " ' ( ( _ ,
NOTE: The gra_-c _1_red sleeve o )ening must
AI)'_YS tace downward to ensure proper
operation of the i/lici'owa_e,
MustFace
Dc
Black
Exhaust
OutletFacing
the Front
Backof
Microwave
2O
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
GE RVM1635WK User manual
-
-
Frigidaire FMV157GMA Installation guide
-
GE JN327H1AA Owner's manual
-
Hotpoint JVM1850BH06 Installation guide
-
Hotpoint REM25SJ03 Owner's manual
-
GE RGB790WEK1WW Owner's manual
-
GE RGB540SEH5SA Owner's manual
-
-
Other documents
-
Dometic DOTR16B Over Range Microwave Oven Installation guide
-
-
GE JVM2052 User manual
-
-
Philips BTB2462/05 Quick Setup Guide
-
Frigidaire FMT148GPB1 Installation guide
-
Electrolux EI30BM60MSC Installation guide
-
Summit MHOTR243SS Installation guide
-
Samsung MC17T8000CG Installation guide
-