Daikin DDC Quick start guide

DDC Controller

Quick Start

Guide

WattMaster Controls Inc.

8500 NW River Park Drive · Parkville, MO 64152

DAIKIN

is a registered trademark of Daikin Industries, LTD

WattMaster Form: DK-QS-DDC-TGD-01A

Neither WattMaster Controls, Inc. nor Daikin Industries,

Ltd. assumes any responsibility for errors or omissions in

this document and are separate companies. This

document is subject to change without notice.

Table of Contents

Section 1: DDC Controller Quick Start Guide (Using Computer) .................................................1

Part 1: Initial Computer and PrismD Setup ..............................................................................

Part 2: Controller Coniguration ....................................................................................................5

Part 3: Schedules ..................................................................................................................................8

Section 2: DDC Controller Quick Start Guide (Using LCD Display) ......................................... 10

Part 1: Controller Setup Using On-Board LCD Display .....................................................

Appendix: Optional Sensor Descriptions ........................................................................................... 14

Troubleshooting ............................................................................................................................................. 15

1

Section1:GoodmanDDCControllerQuickStartGuide(UsingComputer)

Note:

ThisQuickStartGuideisonlyforreferencetomakethestartupprocessfaster.Ifmoreinformationisrequiredonanyof

thefeaturesorwiring,pleaserefertotheDDCControllerTechnicalGuideandthePrismDTechni calGuide.



Part1:InitialComputerandPrismDSetup



1. InstallPrismDsoftwareandtheUSBdriversonyourcomputer.PrismD andtheUSBdriverscanbedownloaded 

atwww.daikin.wattmaster.com.Youcanalsofindinstallationinstructionsthereforbothoftheseitems.



2. AfterPrismDandtheUSBdrivershavebeensuccessfullyinstalledonyourcomputer,youcanthenconnecta

standardUSBcablebetweenthecomputerandcontroller.SeeFigure1.



Figure1:USBCableConnection





USB Cable

Connect to Computer

with PrismD Software Installed

For Stand-Alone Programming

DDC Controller

2

3. VerifythattheCommLinkjumpersareinstalledontheDDCControllerasshowninFigure2.Note:Ifyouare

usinganexternalCommLink5,removethejumpers.Cyclepowertothecontrollerifmakingjumperchanges.



Figure2:On‐BoardCommLinkJumperSetting



4. Open

thePrism2program.Ifyoudidnotcreateashortcuttoyourdesktopdescribedintheon‐linePrismD

instructionsorplacetheprogramontheStartmenu,youcanfindtheprogramatc:\PrismD\PrismD.exe.



5. OncePrismDisopen,clickthe<Login>iconandusethefollowingdefaultuser

nameandPassword

(seeFigure3):UserName:admin;Password:admin



Figure3:LoginIconandLoginWindow

DDC Controller

USE ON-BOARD

COMMLINK

Both Jumpers ON (Default)

LO O

"R"

"T"

"SH

BI5

BI7

BI1

BI2

BI3

BI4

BI8

BI6

AI1

AI2

AI3

AI4

AI5

AI6

AI7

AI8

BINAR

POLA

ENTER

DOWN

ALARM

RELAY CONTACT

RATING IS 1 AMP

MAX @ 24 VAC

RS-485 COMM

LOOP WIRE

“R” TO “R”,

“T” TO “T”

“SHLD” TO “SHLD”

24 VAC POWER

ONLY

WARNING!

POLARITY MUST

BE OBSERVED

OR THE

CONTROLLER

WILL BE

DAMAGED

ANALOG INPUTS

AI1:

A2:I

A3:I

A6:I

A7:I

A8:I

BI1:

BI2:

BI3:

BI4:

BI5:

BI6:

BI7:

AO1

AO2

AO3

SPACE TEMP

CO2 SENSOR

OUTDOOR AIR TEMP

ECONOMIZER FEEDBACK

OUTDOOR AIR HUMIDITY

SPACE HUMIDITY

REMOTE START/STOP

FAN PROVING SWITCH

CLOGGED FILTER SWITCH

EMERGENCY SHUTDOWN

COMP PRESSURE SW 1

DEFROST SWITCH (ES)

LOAD SHEDDING

ECONOMIZER DAMPER:

MOD HGRH:

EXHAUST FAN (SSR):

A4:I

A5:I

BI8:

BINARY INPUTS (24V)

G OUTPUTS

ANALO

WattMaster Label

#S 000067W

Rev.: 1G

E-BUS

EXPANSION

E-BUS

EXPANSION

+24 VAC

HEAT STG2: RLY6

REV. VALVE(S): RLY8

www.wattmaster.com

COMP2/STG2: RLY2

OE377-26B-00001

PCBCG100

24V RLY2: COM2

BLOWER STG2: RLY4

COND FAN: RLY7

24V RLY: COM3-8

USB

AO4

ALARM (SSR):

BINARY OUTPUTS

24V 3-8RLY: COM

HEAT STG1: RLY5

BLOWER STG1: RLY3

24V RLY1: COM1

COMP1/STG1: RLY1

SPACE SLIDE ADJUST

SUPPLY AIR TEMP

COMP PRESSURE SW 2

3

6. Clickthe<Jobsite>icon(seeFigure4).OncetheJobSitesWindowopens,createanameforyourjobsiteinthe

“SelectedLocation”fieldandpress<Enter>.Yournewjobsitenameshouldappearinthe“JobSiteSelection”

window.Note:WhenenteringdatainPrismD,youmustalways

pressthe<Enter>keyaftereachentryinorder

fortheprogramtosavethedata.



7. Clickthe“DownArrow”nexttotheSerialPortdropdownlistandchoosethelistingasshowninFigure4.Note:

Thenumberfollowing“COM”maybedifferentonyourcomputer.

Itshouldstillstartwith“SiliconLabsCP210x

USBtoUARTBridge”.SeetheTroubleshootingSectionattheendofthisguideifyoudonotseethisselection.



Figure4:Job‐SiteIconandJobSitesWindow

8. IntheNetworkConfigurationWindow,clickMultipleLoopConfigurationifusingoneormoreMiniLinks.

Otherwise,selectSingleLoopConfiguration.Onceselected,click<Exit>toclosetheJobSitesWindow.





4



9. Clickonthe<Communications>menuitemandthenchoose“SearchforUnits”.SeeFigure5.



Figure5:CommunicationsMenu‐SearchForUnits



10. IntheSearchForUnitsWindowthatopens,clickthemenuoption<StartSearch>.Whencompletedyoushould

seeonesmallgreensquareasshowninFigure6.



Figure6:SearchForUnits



11. ClosetheSearchForUnitsWindowbyclicking<Exit>.Ifyouwishtosaveyoursearchresults,select<Yes>when

promptedtodoso.



 

5

Part2:ControllerConfiguration



1. Ontheleft‐handsideofthePrismDscreenintheUnitSelectioncolumn,double‐clickonthecontrollerlabeled

“DaikinRTU”.SeeFigure7.



Figure7:UnitSelection

2. TheStatusScreenforthecontrollerwilldisplayasshowninFigure8.



Figure8:ControllerStatusScreen



DaikinRTU

DaikinRTU

6

3. AtthetopoftheStatusScreennexttoDaikinRTU,youwillseeablanktimeof00.00AM.Clickonthistimefield

tobroadcasttherealtimetotheController.SeeFigure9.



 

Figure9:BroadcastTime



4. Fromhere,youcanviewthecurrentstatusoftheunitaswellasaccessthesettingsbyclickingthemenuoption

<Setpoints>locatedatthetopofthewindow.SeeFigure10.



Figure10:SetpointsSelection



Daikin RTU

DaikinRTU

7

5. AsshownbelowinFigure11,youcanselectthesetpointcategorybyclickingononeofthebuttonsatthe

bottomofthescreen.Wheninitiallysettingupacontroller,itisimportanttoverifytheconfigurationsfirst.

Clickonthe<Configuration>category.Note:Whenenteringdata

inPrismD,youmustalwayspressthe<Enter>

keyaftereachentryinorderfortheprogramtosavethedata.



Figure11:ControllerSetpointsScreenandSetpointCategories



6. IntheConfigurationScreen,thereare5Sensorsettingsidentifiedbytheredarrowsthatarefieldoptionsand



theyneedtobesetcorrectlyinorderforthecontrollertooperate.Theseoptionsareshownwitharrowsin

Figure12.However,youshouldstillverifytheothersettingseventhoughtheyshouldbesetcorrectlyatthe

factory.



Figure12:ConfigurationScreen

8

Part3:Schedules



1. Theinternalschedulecanbechangedbyclickingonthe<Schedules>iconlocatedontheControllerStatus

ScreenasshowninFigure13.



Figure13:SchedulesIcon



2. OncetheSchedulesScreenopens,modifythescheduleasnecessary.SeeFigure14.



Figure14:SchedulesWindow

3. Whenyouenteratimeinanyfield,youmusttypein3or4charactersforeachfieldandyoumustdesignateAMorPMand

press<Enter>.Forexample,500PM,<Enter>or1100PM,<Enter>.Note:

YouMUSTpress<Enter>tohavethesystem

acceptyourentry.Ifyoudonotpress<Enter>,thebargraphtotherightwilleithernotdisplayorwillnotchange.



9

4. Toeliminateaschedulefromanyevent,simplytypeazeroandpress<Enter>fortheStartandStoptimeforthatday.The

screenwilldisplay12:00AMforboththeStartandStoptimes,indicatingthattheequipmentwillnotactivateforthatday.



5. Ifyouwantthecontrollertorunthefull24hours,typeazeroandpress<Enter>

toset12:00AMfortheStarttimeand

type11:59PMandpress<Enter>fortheStoptime.Thisensuresthefull24‐hourperiodwillremainintheoccupiedmode

withoutinterruption.



6. Select<Save>

tosaveyourschedule.Select<Restore>torestoreapreviouslysavedschedule.Select<CopytoAll>tocopy

thescheduletoalllikecontrollers,andselect<EraseSchedules>

tocompletelyerasethescheduleappearinginthe

window.WARNING:<EraseSchedules>willclearALLentered.

Selectthe<Holidays>buttonatthebottomleftoftheSchedulesWindowtoscheduleHolidays.TheHolidays

Windowwillappear(seeFigure15).ClickoneachdateyouwishtoselectasaHoliday.AllHolidayswillfollow

thedailyHolidayschedulethatissetintheSchedulesWindow.

Theholidaystartandstoptimeswilloverridethe

standardoperatinghours. Note:Youcanonlyselectholidaysforthecurrentyear.



Figure15:HolidaysWindow

 

10

Section2:GoodmanDDCControllerQuickStartGuide(UsingLCDDisplay)

Note:

ThisQuickStartGuideisonlyforreferencetomakethestartupprocessfaster.Ifmoreinformationisrequiredonanyof

thefeaturesorwiring,pleaserefertotheDDCControllerTechnicalGuideandthePrismDTechni calGuide.



Part1:ControllerSetupUsingOn‐BoardLCDDisplay



The first LCD screen is the initialization screen. To scroll through the rest of the screens, press the <MENU>

button.Pressthe<MENU>buttonuntilyougettotheTIMER/DELAYSScreen.Thenpressthe<ENTER>button

to scrollthroughthe TIMER/DELAYS Screens. Followthedirections

inStep 1. Thenpressthe <MENU> button

untilyouget totheCONFIGSETPTSScreen.Thenpressthe<ENTER>buttontoscrollthroughtheConfiguration

SetpointsScreens.FollowthedirectionsinStep3.



11

2. Thereare5Timersettingsthatarefieldoptionsandtheyneedtobesetcorrectlyinorderforthecontrollerto

operateproperly.Theyareshownbelow:



 

 



12

3. Thereare7Configurationsettingsthatarefieldoptionsandtheyneedtobesetcorrectlyinorderforthe

controllertooperateproperly.However,youshouldstillverifytheaccuracyofallotherconfigurationsettings 

eventhoughtheyshouldbesetcorrectlyatthefactory.



The

ConfigurationSettingsthatneedtobesetcorrectlyareasfollows:

a.SpaceSensorInstalled:AnalogorDigital

b.HumiditySpaceSensorInstalledorNotInstalled

c.HumiditySpaceSensorInstalled:AnalogorDigital

d.Economizer:EconomizerOnly,CO

orNone

e.EconomizerEnableSource:Drybulb,Dewpoint,orEnthalpy

f.CO

SensorInstalledorNotInstalled

g.CO

SensorInstalled:AnalogorDigital



Usethe<UP>and<DOWN>buttons tochangescreenvalues.



 



13



 





14

Appendix:OptionalSensorDescriptions



IftheoptionalsensorsarepurchasedfromDaikin,thefollowingpictureswillhelpyoudeterminethetypeofsensorthat

youhave.However,someoftheoptionalsensortypesarenotprovidedbyDaikin,suchastheAnalogSpaceHumidity

Sensor(notshown).



 











AnalogSpaceSensor

OVR



DigitalSpaceSensor

withLCDDisplay



AnalogCO

Sensor



DigitalCO

Sensor



DigitalSpaceSensor

withoutLCDDisplay

15

Troubleshooting

WhatCanIDoIfICannotFindSiliconLabsUnderSerialPortsInPrismD?



1. AsshownintheFigureabove,theserialport“SiliconLabsCP210xUSB”shouldbeanoptionunder<SerialPort>.

Ifthisoptionisnotshown,youwillneedtocheckyourcomputer’sinternalpor tsforthe correctCOMnumber.



2. Gotothe<ControlPanel>inyour

computerandclickon<DeviceManager>.Thiswillopenyourcomputer’s

DeviceManagerWindow.Findandclickon<Ports(COM&LPT)>.



3. UnderPorts(COM&LPT),lookforSiliconLabsandverifytheCOMnumber itisinstalledon.Withthis

information,gobacktoPrismDand

underJobSite,selectthecorrectSerialPort.Inthisexample,COM3.

16

Troubleshooting

WhatIfIForgetMyPassword?

Ifyouhavechangedtheadministratoraccessusernameandpasswordfromitsdefaultusername“admin”andpassword

“admin”andyouforgotoneorboth,youmayresettheadministratoraccesstofactorydefaultmodebyfollowingthe

stepsbelow.

1. UndertheC:drive,findandopenyourPrismDfolder.Inthisfolderyouwillfi

ndaninternalfoldernamed,

“Configuration.”Double‐clicktoopenthefolder.



2. Insidethisfolderyouwillfindmultiplefiles.Lookforafilenamed“ULData.cfg.”Rightclickonthisfileandselect

<Delete>.



3. ThiswillresettheUsernameand Passwordto“admin”

Notes

WattMaster Form: DK-QS-DDC-TGD-01A June 2016

WattMaster Controls Inc. • 8500 NW River Park Drive • Parkville, MO • 64152

Daikin DDC Quick start guide

Related papers

Other documents