VONN Lighting VOI19018SS Installation guide

Brand
VONN Lighting
Model
VOI19018SS
Type
Installation guide

VONN Lighting VOI19018SS is a 12V AC low voltage fixture that requires a transformer to operate. It is designed for outdoor use and can be installed in concrete. The fixture comes with all necessary parts for installation, including wire connectors, screws, and a hex wrench. It is recommended to use a qualified, licensed electrician to install the fixture. Once installed, the fixture can be turned on and off using the switch on the circuit box.

VONN Lighting VOI19018SS is a 12V AC low voltage fixture that requires a transformer to operate. It is designed for outdoor use and can be installed in concrete. The fixture comes with all necessary parts for installation, including wire connectors, screws, and a hex wrench. It is recommended to use a qualified, licensed electrician to install the fixture. Once installed, the fixture can be turned on and off using the switch on the circuit box.

Installation Guide
ON
© VONN Lighting,2019
Model: VOI19018
Parts List
A.
B.
C. Hex Wrench
A
Circuit Box
Wire Connectors x 4
Screws x 3
Make sure that you have all necessary parts by checking the parts list. If
any part is missing or damaged, please contact VONN Lighting
Customer Service at 888-604-8666 for a replacement.
Please read and comprehend the entire manual before attempting to
assemble, operate, or install the product.
VONN highly recommends to use a qualified, licensed electrician to install
the fixture.
LED INFO & WARNINGS
•
•
All parts must be used as indicated in these instructions. Do not substitute
any parts, leave parts out, or use any parts that are worn or broken.
•
Inspect the LED fixture prior to installation to make sure that it has not
been damaged during shipping.
•
Please handle the LED light with care when unpacking. Do not apply
pressure to the LEDʼs, do not open any factory sealed compartments, and
do not touch the LEDs with your hands.
•
Shut “OFF” the electricity at main fuse box.
•
•
Do not remove or replace VONN manufactured driver that are provided
with the fixture.
VONN Lighting
Tools You May Need
GOGGLES
TAPE MEASURE
RUBBER
GLOVES
B
12V AC Low Voltage Fixture (TRANSFORMER IS REQUIRED)
•
PHILLIPS
SCREW DRIVER
C
© VONN Lighting,2019
Legend
L = Live/Hot/Black
N = Neutral/White
= Ground/Green
•Remove fixture from plastic housing by loosening
screws.
•Thread supply wires through plastic housing.
•Insert plastic housing into prepared concrete ground.
ON
ON
Circuit Box
4. Turn Power ON
Turn electricity “ON” at main fuse box.
3. Supply Wires:
Ground Wires:
Connect White (Neutral Wire) from fixture to power White
(Neutral Wire).
Connect Green (Ground Wire) from fixture to supply Green
(Ground Wire).
Twist wires together clockwise and secure with wire
connector (A).
Connect Black (Line Wire) from fixture to power Black (Hot
Wire).
•
•
•
•
•Tuck wires in plastic housing. Insert fixture into plastic housing.
•
2. Remove Fixture
Plastic Housing
Plastic Housing
Concrete
Installation Hole Size
Refill with pea gravel
or sand
1. Prepare Hole
Prepare concrete for plastic housing.
•
•Secure fixture by tightening screws (B) with screw driver.
Ø5”
Ø129mm
4.25”
110mm
A
B
  • Page 1 1
  • Page 2 2

VONN Lighting VOI19018SS Installation guide

Brand
VONN Lighting
Model
VOI19018SS
Type
Installation guide

VONN Lighting VOI19018SS is a 12V AC low voltage fixture that requires a transformer to operate. It is designed for outdoor use and can be installed in concrete. The fixture comes with all necessary parts for installation, including wire connectors, screws, and a hex wrench. It is recommended to use a qualified, licensed electrician to install the fixture. Once installed, the fixture can be turned on and off using the switch on the circuit box.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers