Good Lumens by Madison Avenue 70005 Installation guide

THANK YOU

We appreciate the trust and confidence you have placed in Good Lumens through the purchase of this fixture. We strive to continually create quality products

designed to enhance your home. Visit us online to see our full line of products available for your home improvement needs. Thank you for choosing Good

Lumens!

Model #70005

USE AND CARE GUIDE

5 Light LED Bath Vanity

(METALLIC BRONZE)

Questions, problems, missing parts? Before returning to the store,

call Good Lumens Customer Service

8 a.m. – 7 p.m., EST, Monday – Friday, 9 a.m. – 6 p.m., EST, Saturday

800-527-0998

LA-2814E/S/F

2

Please contact (800)527-0998 for further assistance.

Table of Contents

Table of Contents .......................................................... 2

Safety Information ......................................................... 2

Limited Warranty ........................................................... 2

Pre-installation .............................................................. 3

Tools required for assembly & installation (not included) ........... 3

Hardware Included ................................................................... 4

Package Contents .................................................................... 5

Assembly ....................................................................... 6

Installation ..................................................................... 7

Maintenance .................................................................. 9

Care and Cleaning ........................................................ 9

Troubleshooting ............................................................ 9

Service Parts ............................................................... 10

Safety Information

Before you begin, make sure you carefully read and understand the instructions in this manual. Please follow the instructions in the order presented

in this manual and observe all warnings and cautions.

WARNING: To reduce the risk of fire, consult a qualified

electrician before installation.

WARNING: Before beginning installation, turn off electricity at the

circuit breaker box or the main fuse box.

WARNING: Be careful not to damage or cut the wire

insulation (covering) during fixture installation. Do not

permit wires to contact any surface having a sharp edge.

To do so may damage or cut the wire insulation, which

could cause serious injury or death from electric shock.

CAUTION: Consult a qualified electrician before

installation.

WARNING: If a dimmer control switch is used with this

fixture, obtain professional advice to determine the

correct type to use as well as the electrical rating

required.

CAUTION: All electrical connections must be in agreement

with local codes, ordinances, or the National Electric Code

(NEC). Contact your municipal building department to learn

about your local codes, permits and/or inspections.

Limited Warranty

WHAT IS COVERED

The manufacturer warrants this lighting fixture to be free from defects in materials and workmanship for a period of five (5) years from date of

purchase. This warranty applies only to the original consumer purchaser and only to products used in normal use and service. If this product is found

to be defective, the manufacturer’s only obligation, and your exclusive remedy, is the repair or replacement of the product at the manufacturer’s

discretion, provided that the product has not been damaged through misuse, abuse, accident, modifications, alterations, neglect or mishandling.

This warranty shall not apply to any product that is found to have been improperly installed, set-up, or used in any way not in accordance with the

instructions supplied with the product. This warranty shall not apply to a failure of the product as a result of an accident, misuse, abuse, negligence,

alteration, or faulty installation, or any other failure not relating to faulty material or workmanship. This warranty shall not apply to the finish on any

portion of the product, such as surface and/or weathering, as this is considered normal wear and tear.

WHAT IS NOT COVERED

The manufacturer does not warrant and specially disclaims any warranty, whether express or implied, of fitness for a particular purpose, other than

the warranty contained herein. The manufacturer specifically disclaims any liability and shall not be liable for any consequential or incidental loss or

damage, including but not limited to any labor / expense costs involved in the replacement or repair of said product.

Contact the Customer Service Team at (800)527-0998.

3

Please contact (800)527-0998 for further assistance.

.

Pre-installation

TOOLS REQUIRED FOR ASSEMBLY & INSTALLATION (NOT INCLUDED)

Safety

goggles

Phillips

screwdriver

Flathead

screwdriver

Wire

strippers

Step

ladder

Wire

cutters

Electrical

tape

4

Please contact (800)527-0998 for further assistance.

Pre-installation (continued)

HARDWARE INCLUDED

NOTE: Hardware not shown to actual size.

Part

Description

Quantity

AA

Wire connectors

3

BB

Outlet box screws

2

CC Ground screw 1

DD Wood screws 2

EE Mounting plate 1

FF

Plastic anchors

2

AA

BB

CC

DD

FF

EE

5

Please contact (800)527-0998 for further assistance.

.

Pre-installation (continued)

PACKAGE CONTENTS

Part

Description

Quantity

A

Screw shells

5

B

Spanner

1

C

Glass shades

5

D

Screws

4

E

Fixture body

1

A

C

B

D

E

6

Please contact (800)527-0998 for further assistance.

Assembly

1

Attaching the glass shade

□ Carefully unpack your new fixture and lay out all the parts on a clear area. Take care not to lose any small parts necessary for installation.

□ Remove the screw shell (A) from the fixture.

□ Place the glass shades (C) over the socket of the fixture body (E), fasten with screw shells (A) using the included spanner (B).

C

A

B

E

Socket

7

Please contact (800)527-0998 for further assistance.

.

Installation

1

Removing the mounting plate

2

Position the mounting plate

□ Prior to installation, remove the mounting plate (EE) by removing

the screws (D) from the fixture body (E).

□ Position mounting plate (EE) on the wall, and mark location of

two mounting holes.

□ Drill the holes on the wall, insert the plastic anchors (FF) into

the wall.

3

Install the mounting plate

□ Attach the mounting plate (EE) to the outlet box using the outlet

box screws (BB) and the wood screws (DD). The side of the

mounting plate marked “GND” must face out.

FF

Outlet Box

EE

Outlet Box

FF

EE

BB

DD

EE

D

E

8

Please contact (800)527-0998 for further assistance.

Installation(continued)

4

Connecting the wires

□ Connect the white wire from the fixture to the white wire from the

outlet box, and the black wire from the fixture to the black wire

from the outlet box. Cover the two wire connections using the two

provided wire connectors (AA). Wrap the two wire connections with

electrical tape for a more secure connection. If your outlet box has

a ground wire (green or bare copper), connect fixture’s ground wire

to it using the wire connectors (AA). Otherwise connect the copper

ground from the fixture to ground screw (CC) on the mounting

plate (EE). Note: If you have electrical questions, consult your local

electrical code for approved grounding method.

5

Place fixture body to mounting plate

□ Place fixture body (E) over mounting plate (EE) and secure with

screws (D).

□ Installation is complete. Turn on the power at the circuit breaker or

fuse box. Turn the light switch on to activate the fixture.

Outlet Box

EE

CC

AA

White wire

Black wire

Ground wire

Black wire

E

EE

D

E

9

Please contact (800)527-0998 for further assistance.

.

Maintenance

□ Shut off the main power supply before performing any maintenance on the light.

□ Wipe with damp cloth or use window cleaner. Do not use abrasives.

Care and Cleaning

□ To clean the outside of the fixture, use a dry or slightly dampened clean cloth (use clean water, never a solvent) to wipe the glass and

surface of the fixture.

□ To clean the inside of the fixture, first disconnect power to the fixture by turning off the circuit breaker or by removing the fuse at the fuse

box. Next, use a dry or slightly dampened clean cloth (use clean water, never a solvent) to wipe the inside glass and interior surface of the

fixture.

□ Do not use any cleaners with chemicals, solvents or harsh abrasives. Use only a dry soft cloth to dust or wipe carefully

Troubleshooting

Problem

Possible Cause

Corrective Action

The bulb will not light.

The power is off.

Make sure power supply is on.

There is a faulty wire connection.

Check the wiring.

There is a faulty switch.

Test or replace the switch.

The fuse blows or circuit breaker

trips when the light is turned on.

There are crossed wires or the

power wire is grounding out.

Check the wire connections.

10

Please contact (800)527-0998 for further assistance.

Service Parts

MODEL TYPE

Part

Description

Quantity

Part

Description

Quantity

AA

Wire connectors

3

A

Screw shells

5

BB

Outlet box screws

2

B

Spanner

1

CC

Ground screw

1

C

Glass shades

5

DD

Wood screws

2

D

Screws

4

EE

Mounting plate

1

E

Fixture body

1

FF

Plastic anchors

2

DD

FF

D

A

AA

BB

CC

C

E

B

EE

Questions, problems, missing parts? Before returning to the store,

call Good Lumens Customer Service

8 a.m. – 7 p.m., EST, Monday – Friday, 9 a.m. – 6 p.m., EST, Saturday

800-527-0998

Retain this manual for future use.

Page is loading ...

Good Lumens by Madison Avenue 70005 Installation guide

Good Lumens by Madison Avenue 70005 Installation guide

in other languages

Related papers

Other documents