HanoverOutdoorFurniture
IMPORTANT
Ifyouhaveanyproblemswiththisproduct(missingordamagedparts,assemblyissues,etc.),
PLEASEDONOTRETURNTOTHERETAILER/STORE
fromwhereyoupurchasedtheproduct.
PleasecallourToll‐FreeCustomerServiceHotlineat:
1‐800‐416‐3511
Between9:00AMand5:00PMEasternTime,MondaythroughFriday
Orvisitourwebsiteat:
www.hanover‐products.com
Toexpediteanyfuturewarrantyclaims,pleaseretaintheInstructionSheet,Warranty
Cardandreceiptforfutureuse.
For additionalon‐linesupportonassembly,troubleshootingandcare&maintenanceofyouroutdoor
furniture,pleasevisitourwebsiteat:www.hanover‐products.com.
6/1/2015(a)
Page 4
*NOTE:PARTSSHOWNONPARTSLISTARENOTTOSCALE
PARTS IDENTIFICATION LIST
AAF06000
PARTS LIST ORDER PART #DESCRIPTION
A
FOOT CAP
FACTORY ASSEMBLY
FC0030
A
ASSEMBLY INSTRUCTIONS
WARNING
Do not store or use gasoline or other
flammable vapors and liquids in the
vicinity of this or any other appliance.
An LP-cylinder not connected for use
shall not be stored in the vicinity of this
or any other appliance.
DANGER
If you smell gas:
1. Shut off gas to the appliance.
2. Extinguish any open flame.
3. If odor continues, keep away from
the appliance and immediately call
your gas supplier or fire department.
WARNING:
USE FACTORY APPROVED
REPLACEMENT PARTS AND
ACCESSORIES ONLY. USE
OF UNAPPROVED PART OR
ACCESSORIES CAN VOID
THE WARRANTY ON THIS
PRODUCT AND RESULT IN
AHAZARDOUS CONDITION.
PLEASE CONTACT US FOR
INFORMATION REGARDING
REPLACEMNT
HOSES,THERMOCOUPLES,
ELECTRODES,IGNITION
MODULES,LAVAROCKS,LO
GS, FIRE ICE, ETC.
WARNING:
Improper installation, adjustment alteration,
service or maintenance can cause injury or
property damage. Read the installation,
operating and maintenance instructions
thoroughly before installing or servicing this
equipment.
FOR USE WITH 20LB (9KG) PROPANE
CYLINDER WITH TYPE 1 CONNECTION OR FOR
USE WITH NATURAL GAS AFTER CONVERSION
KIT IS INSTALLED (MUST BE PROFESSIONALLY
INSTALLED) ALSO THE LP REGULATOR MUST
BE SUPPLIED BY THE MANUFACTURER.
Jan-01-2015
Installer: Leave these instructions with consumer.
Consumer: Keep these instructions for future reference.
WARNING: For Outdoor Use Only
Questions, Problems, Missing Parts? Before returning to
your retailer, call our customer service department in the
US and Canada at 1-800-416-3511, Monday-Friday, 9 a.m.–
5 p.m. Eastern Time.
This appliance can produce carbon
monoxide which has no odor.
Using it in an enclosed space can kill
you.
Never use this appliance in an enclosed
space such as a camper, tent, car or
home.
DANGER CARBON MONOXIDE HAZARD
CSA Model99010
ARL00200
PARTS IDENTIFICATION LIST
PART DESCRIPTION PART# QTY
A
CONTROL KNOB FP1245 1
B
GAS VALVE FP0307 1
C
THERMOCOUPLE FP0004 1
D
LP REGULATOR
HOSE
65-FP-0181 1
E
ELECTRODE 65-FP-0128 1
F
ORIFICE ELBOW FP0310 1
G
IGNITION
MODULE
FP0006 1
H
PROPANE
ORIFICE
ZCF0021 1
I
“AAA”
BATTERY(1.5V)
HW0705 1
J
LAVA ROCK SET FP0002 1
K
FOOTCAP FC0743 4
L
1/4" X 15 MM BOLT HW0034 8
M
1/4" X 20 MM BOLT HW0036 4
O
1/4" X 40 MM BOLT HW0086 4
P
HEX BOLT DRIVER HW0006 1
Q
BOLT COVER HW0105 18
R
WASHERS-1 HW0004 14
S
WASHERS-2 HW0712 4
T
NUTS HW0717 2
U
HEX BOLT
DRIVER
HW0008 1
V
TABLE RIM 1
W
BACK PANEL 1
X
LEFT SIDE PANEL 1
Y
RIGHT SIDE
PANEL
1
Z
DOOR PANEL 1
AA
LP SUPPORT 1
BB TILE-1 4
CC
TILE-2 4
DD
MIDDLE SUPPORT 1
EE
TABLE COVER 1
FF
BOTTOM/ TOP
CONNECTOR
1
INSTALLATION
1. Identify parts packed in carton against the parts list. Remove all protective materials and
set parts on a flat, non-abrasive surface.
2. Attach the back panel to side panels by using four 1/4"x40 mm bolts and washers as
shown in Figure 2. Guide bolts through holes in back panel, into pre-drilled holes in the
side panels. Hand tighten only.
Figure 2
3. Attach the middle support to the side panels by using two 1/4"x15 mm bolts and
washers as shown in Figure 3. Guide bolts through the holes in the middle support, into
pre-drilled holes in the side panels. Hand tighten only.
Figure 3
4. Attach the "L" connector to right side panel by using a 1/4"x15 mm bolt and washer as
shown in Figure 4. Guide bolt through hole in "L" connector, into pre-drilled hole in the
right side panel. Do not over tighten.
Figure 4
5. Put the door onto the "L" connector (pre-assembled), guide the pin on the lower "L"
connector into the hole under the door. Then guide the pin on the upper "L" connector
into the hole in the upper portion of the door. Use a 1/4"x15 mm bolt and washer to
secure the "L" connector to the right side panel as shown in Figure 5. Do not over
tighten.
Figure 5
6. With the help of another person, carefully place the table top onto the table base.
After making any necessary adjustments to the alignment of the table top and the
assembled base, use four 1/4"x15 mm bolts and washers as shown in Figure 6. Guide
the bolts through the holes under the table top, into the pre-drilled holes in the side
panels. Do not tighten completely.
Figure 6
7. Attach the LP support to door panel by using four 1/4"x15 mm bolts and washers as
shown in Figure 7. Do not over tighten.
Figure 7
8. Place gas tank onto the LP support as shown in Figure 8.
Figure 8
9. Attach the metal ring (as shown in Figure 9) pre-fitted with gas hose which is
connected to the table top, into the hole of the door panel, then use hex bolt driver to
screw 1/4"x5mm nut, the gas tank has fixed as shown in Figure 10. Connect the
regulator as shown in Figure10. Screw the black handle clock-wise to tighten. Turn the
handle counterclockwise to remove. The hose must point down. Check that the valve is
turned all the way clockwise to the "OFF" position.
Figure 10
Figure 9
10. After making any necessary adjustments to the parts, use the hex bolt driver to tighten
all bolts. Note: each bolt must be tightened a few revolutions at a time. Repeat until all
bolts are tight. Do not over tighten. Over tightening may strip bolts. Cover all bolts with
covers.
11. Note the clear bumpers spaced evenly throughout the inside of the table top. Carefully
place tiles inside table rim, resting on the clear bumpers as shown in Figure 11
Figure 11
12. Pour the lava rocks into the burner completely covering the burner. See Figure 12
Ignition Well
13. Remove the cardboard cover from the ignition well as shown in Figure 13. Remove
any lava rock or fire ice on top of ignition well.
Cardboard Cover
Figure 12
Figure 13
14. Open the tank valve. Apply a solution of soapy water to the tank-regulator connection
and to the valve-hose connection to check for leaks as shown in Figure 14 If soap
bubbles continue to form, the connection has a leak. If a leak is found, close the tank
valve and tighten all connections.
NOTE: NEVER USE A FLAME TO CHECK FOR LEAKS.
BATTERIES
Make sure the control knob is in the "OFF" position.
Unscrew the push button cap on the ignition module
located on the control panel to access the battery
compartment. The ignition module requires one Alkaline
AAA size battery (1.5V). The negative (-) end goes in first.
See Figure 15 Dispose of battery safely. May explode or
leak if charged or disposed of in fire. Make sure of the
polarity. Mercury and cadmium free.
Checking the tank-regulator for leaks
Figure 14
Figure 15
/
