Bosch HGG223121M/01 User manual

Type
User manual
06
071096
Ú Instructions for connecting gas and gas conversion (for
After-Sales Service only)
2
Ú Table of contents
Ú Instructions for connecting gas and gas conversion (for After-Sales Service only)
Measures to note ....................................................................... 2
Choose which side of the appliance to connect the gas on (*
optional)................................................................................................3
Gas connection.......................................................................... 3
Approved connections.......................................................................3
Natural gas connection (NG)............................................................3
Liquefied gas connection (LPG) ......................................................4
Conversion to a different gas type........................................... 5
Converting to a different gas type ...................................................5
Functional parts for the gas conversion.........................................5
Replacing the burner nozzles...........................................................5
Adjusting or replacing the burner bypass screws and setting
the small flame ....................................................................................6
Converting the appliance from natural gas to liquefied gas ......6
Conversion from liquid gas to natural gas.....................................6
Removing the control panel..............................................................6
Replacing bypass screws .................................................................7
Fitting the control panel.....................................................................8
Replacing the oven burners (optional) ...........................................8
Leak test and function test ....................................................... 9
Check the gas connection ................................................................9
Checking the burner nozzles............................................................9
Checking the bypass valves.............................................................9
Checking the oven burner nozzle (option).....................................9
Check the grill burner nozzle (option) ............................................9
Correct flame formation ............................................................ 9
Burner ...................................................................................................9
Oven ......................................................................................................9
Technical data – Gas ............................................................... 10
Measures to note
The appliance may only be converted to a different gas type
by an approved specialist, in accordance with the
instructions in this manual.
Incorrect connection and incorrect settings may cause
serious damage to the appliance. The appliance
manufacturer accepts no liability for damage and
malfunctions of this kind.
Pay close attention to the symbols indicated on the rating plate.
If there is no symbol for your country, follow the technical
guidelines that apply in your country when making settings.
Before setting up the appliance, determine the gas type and
pressure in the local supply network. Before using the
appliance for the first time, make sure that all settings have
been made correctly.
Pay attention to local and international rules and regulations.
All connection data can be found on the rating plate on the rear
of the appliance.
Enter the data in the following table:
Product number (E no.),
Manufacturing number (FD),
Enter the factory settings for gas type/gas pressure, as well as
the settings for gas type/pressure that apply after the gas
conversion, in the following table.
The changes made to the appliance and the type of connection
play an important role in ensuring that the appliance operates
correctly and safely.
: Risk of gas escape!
After connecting the appliance to the gas supply, always
check the connection for leak tightness. The manufacturer
accepts no responsibility for the escape of gas from a gas
connection which has been previously tampered with.
Risk of gas leak!
Do not move the appliance by pulling on the gas pipe
(collector). This could damage the gas pipe.
Risk of gas leak!
The appliance must not be moved once it has been installed.
If you do move the appliance once it has been installed,
check that the connection is leak-tight.
Switch off the power and gas supply before carrying out any
work.
This appliance must not be installed on boats or in vehicles.
E no. FD no.
After-sales serviceO
Type of gas / gas pressure
Data on the rating plate
Type of gas / gas pressure
Data after gas conversion
3
Choose which side of the appliance to
connect the gas on (* optional)
The gas supply to the appliance can be connected on the left
or right. The side on which the gas supply is connected can be
changed if necessary.
Connect the main gas supply.
If you change the side on which the gas supply is connected,
the gas connection piece on the side that is not being used
must be sealed with a blind plug.
To do this:
1. Place the new seal in the blind plug. Make sure the seal is
seated correctly.
2. Secure the gas connection piece to the appliance using a 22
mm spanner and place the blind plug onto the connection
piece using a 24 mm spanner.
Once the side on which the gas supply is connected has been
changed, check that the connection is leak-tight. See the
section entitled "Leak testing" for more information about this.
Note: Use a torque wrench to connect the appliance.
* Option: Only valid for some models.
Gas connection
Approved connections
These instructions apply only when the appliance is set up in
countries that are indicated on the rating plate.
If the appliance is set up, connected and used in a country that
is not indicated on the rating plate, installation and assembly
instructions must be used that contain data and information on
the valid connection conditions in the relevant country.
Natural gas connection (NG)
If natural has (NG) is used, the gas supply should be
connected via a gas pipe or a safety gas hose with threaded
fittings at both ends.
Connection in accordance with EN ISO 228 G
^ (TS EN ISO
228 G
^ )
1. Place the new seal in the connection piece. Make sure the
seal is seated correctly.
2. Secure the gas connection piece to the appliance using a 22
mm spanner and place the connection piece into the
connection piece using a 24 mm spanner.
3. Place the new seal into the gas pipe or safety gas hose.
Make sure the seal is seated correctly.
4. Secure the connection piece using a 24 mm spanner. Use a
24 mm spanner to place the threaded fitting of the gas pipe
or safety gas hose on the connection piece and tighten it
firmly.
5. For information on how to carry out leak testing, see the
section entitled "Leak testing". Open the gas connection shut-
off.
: Risk of gas leak!
When connecting the gas pipe or safety gas hose, do not
tighten the gas connection piece on the appliance using a 22
m spanner. This may damage the connection piece.
Notes
*G^: EN ISO 228 G^ (TS EN ISO 228 G^)
Use a torque wrench to connect the appliance.

1P
6:

6:

6:

6:


1P
*ê
1***
6:

6:

*ê
1***

1P
4
Connection in accordance with EN 10226 R
^ (TS 61-210 EN
10226 R
^ )
1. Place the new seal in the connection piece. Make sure the
seal is seated correctly.
2. Secure the gas connection piece to the appliance using a 22
mm spanner and place the connection piece into the
connection piece using a 24 mm spanner.
3. Secure the connection piece using a 24 mm spanner. Use a
24 mm spanner to place the threaded fitting of the gas pipe
or safety gas hose on the connection piece and tighten it
firmly.
4. For information on how to carry out leak testing, see the
section entitled "Leak testing". Open the gas connection shut-
off.
: Risk of gas leak!
When connecting the gas pipe or safety gas hose, do not
tighten the gas connection piece on the appliance using a 22
m spanner. This may damage the connection piece.
Notes
*R^: EN 10226 R^ (TS 61-210 EN 10226 R^)
Use a torque wrench to connect the appliance.
Liquefied gas connection (LPG)
Caution!
Observe the specific guidelines for each country.
If liquid gas (LPG) is used, the gas supply should be connected
via a gas hose or a fixed connector.
Important information on using a gas hose:
Use a safety gas hose or a plastic gas hose (8 or 10 mm in
diameter).
It must be attached to the gas connection using an approved
connecting device (e.g. a hose clamp).
The hose must be short and completely leak-tight. The hose
must not be longer than 1.5 m. Observe the applicable
guidelines.
The gas hose must be replaced once a year.
1. Place the new seal in the connection piece. Make sure the
seal is seated correctly.
2. Secure the gas connection piece to the appliance using a 22
mm spanner and place the connection piece into the
connection piece using a 24 mm spanner.
3. Fit the safety gas hose and use a pipe union or cable clamp
to tighten it securely.
4. For information on how to carry out leak testing, see the
section entitled "Leak testing". Open the gas connection shut-
off.
Note: Use a torque wrench to connect the appliance.
6:

6:


1P
1***
5ê
6:

6:

1***

1P
5ê
6:

/3***
6:


1P
5
Conversion to a different gas type
Converting to a different gas type
The gas connection must be replaced.
The burner nozzles must be replaced.
Depending on the factory gas setting, the bypass screws in
the burner valves must either be replaced, or screwed in fully.
If present, the oven and grill nozzles must also be replaced.
Numbers are printed on the nozzles indicating their diameter.
Further information about the gas types suitable for the
appliance, as well as the corresponding gas nozzles, can be
found in the section entitled "Technical properties - gas".
After the conversion
After the appliance has been converted to a different gas
type, you must perform a leak test. See the section entitled
"Leak test".
After the appliance has been converted to a different gas
type, the correct flame formation must be tested. See the
section entitled "Correct flame formation".
Enter the newly-set type of gas and gas pressure in the table.
See the section entitled "Measures to be observed".
Caution!
After the appliance has been converted to a different gas type,
the labels giving information on the gas type and showing a
star must be affixed at the appropriate point on the rating plate
MAKE SURE THAT YOU DO THIS.
Functional parts for the gas conversion
The functional parts that are required for the gas conversion in
accordance with the instructions are displayed below.
You will find the correct nozzle diameters in the table in the
section entitled "Technical properties - gas".
Always use new seals.
The gas connecting piece to be used may vary depending on
the gas type and country-specific regulations.
(*) These functional parts must be used when the gas is
connected.
Replacing the burner nozzles
1. Make sure all the knobs on the control panel are turned off.
2. Close the gas connection shut-off.
3. Remove the pan supports and burner parts.
4. Remove the burner nozzles (7 mm socket wrench).
Bypass screw
Burner nozzle
(*) Seal
(*) Connecting piece for natural
gas
(NG: G20, G25)
TS 61-210 EN 10226 R
^
EN 10226 R^
(*) Connecting piece for natural
gas
(NG: G20, G25)
TS EN ISO 228 G
^
EN ISO 228 G^
(*) Connecting piece for liquid gas
(LPG: G30, G31)
Gas connecting piece
Dummy plug (shut-off piece)
6:
6
5. If your appliance features a wok burner with side access,
remove the burner nozzle as shown below (7 mm open-
ended spanner).
6. The burner nozzles can be found in the table; see the section
entitled "Technical data – Gas".
Fit the new nozzles into the appropriate burners.
After replacing the nozzles, check that there are no leaks. See
the section entitled "Testing for leaks".
Adjusting or replacing the burner bypass
screws and setting the small flame
The bypass screws regulate the minimum flame height of the
burners.
Preparation
Shut off the gas supply.
: Risk of electric shock!
Interrupt the power supply to the appliance.
1. Turn off the switches on the control panel.
2. Remove the control knobs individually by holding tightly on to
the control panel and pulling them straight out.
Converting the appliance from natural gas to
liquefied gas
If the appliance was set to natural gas at the time of delivery
(factory setting) (NG: G20, G25) and is now being converted to
liquefied gas for the first time (LPG: G30, G31):
For models with safety pilot:
In order to reach the bypass nozzles, the control panel must be
removed. See the section "Removing the control panel".
The bypass nozzles must be tightened as far as they will go.
You must then carry out the work steps in the section "Installing
the control panel".
For models with gas oven (optional):
In order to reach the bypass nozzle underneath the burner tap,
you must remove the control panel. See the section "Removing
the control panel".
The bypass nozzle on the oven burner must be tightened as far
as it will go.
You must then carry out the work steps in the section "Installing
the control panel".
Conversion from liquid gas to natural gas
If the appliance is to be converted from liquid gas
(LPG: G30, G31) to natural gas (NG: G20, G25), or this
conversion has already been performed and is now to be
reversed:
All bypass nozzles on the appliance must be replaced. To do
this, read the section entitled "Removing the control panel".
The instructions in the section entitled "Replacing the bypass
screws" must then be followed.
Then, follow the instructions in the section entitled "Attaching
the control panel".
Removing the control panel
1. If the appliance has an upper cover, remove this.To remove
the cover, open it, take hold of it at the sides with both hands,
and pull it upwards. The upper cover will come away. Take
care not to lose the hinges.
2. Remove the pan supports and burner parts.
3. If there are any burner connection screws in the hob, remove
them all.
7
4. Remove the two screws (T20) at the front right and left of the
hob panel. Do not remove the plastic parts underneath.
5. For models with a wok burner (optional): Remove the four
screws (M4) from the wok burner.
6. Hold the hob panel at the front and tilt it upwards at an angle
of no more than 30°. Use the profile bar, which can be
positioned upright on the front burner fastening, to prop up
the hob panel.
7. Remove the plastic covers from the front profiles on the right
and left (without scuffing or scratching them). Unscrew the
screws (T20) underneath them.
8. Remove the two screws (M4) that are uncovered when you
remove the control knobs (T15).
9. Take hold of the front panel with both hands and slowly pull it
upwards. Release it from its fastening clips. Then carefully
pull the panel forwards to remove it. Ensure that the cables
are not damaged and the connections do not come loose.
Replacing bypass screws
1. Loosen the bypass screws with a flat screwdriver (no. 2).
Remove the bypass screws.
2. You can use the table to determine the new bypass screws
that you will need after the gas conversion. See the section
entitled "Technical properties - gas".
3. Check whether the seals on the bypass screw are correctly
seated and work precisely. Only use bypass screws with
intact seals.
4. Insert the new bypass screws and tighten them. Make sure
that all bypass screws are connected to the correct shut-off
valves.
5. At this point, it is essential to carry out a leak test. See the
section entitled "Leak test".
8
Fitting the control panel
To fit the control panel, follow the instructions for removing it in
the reverse order.
1. Take hold of the front panel with both hands and carefully fit
it into place. Ensure that the cables are not damaged and the
connections do not come loose.Lower the front panel slightly
and place it in the fastening brackets.
2. Screw the two screws (T15 and M4) that you removed from
the control panel back in.
3. Screw the screws (T20) that you removed from the front
profiles back in on the right and left.Refit the plastic covers.
4. Fit the hob panel carefully. Make sure that the plastic parts
underneath the screws do not fall out. Screw the two screws
(T20) back in at the front right and left of the hob panel. If
there are any burner connection screws, screw them all into
the hob panel.
5. For models with a wok burner (optional): Screw the four Torx
screws (M4) that you removed from the wok burner back in.
6. If your cooker has an upper cover, take hold of it on both
sides, hold it upright and push it straight down into the
holder.
7. Fit burner housings of the correct size onto each burner, and
ensure that the spark plug is inserted into the opening on the
edge of the burner housing. Place the enamelled burner caps
in the centre of the matching burner bases.
8. Refit the pan supports. Make sure that the 80 mm-wide pan
support is fitted on the auxiliary burner.
9. Fit the control knobs carefully.
10.At this stage, it is important to check that the burners are
burning correctly; see section entitled "Correct burner
behaviour".
11.Check whether the appliance is functioning correctly.
Replacing the oven burners (optional)
Preparation
Turn off all switches on the control panel.
Shut off the gas supply.
: Risk of electric shock!
Interrupt the power supply to the appliance.
Replacing the nozzle for the oven burner
1. Open the oven door.
2. Loosen the front securing screw in the bottom plate.
3. Hold the bottom plate firmly at the front, lift and remove it.
4. Loosen the burner securing screw and carefully remove the
oven burner. The burner nozzles are now freely accessible.
Make sure that the thermocouple and ignition plug
connections are not damaged.
5. Release the nozzle at the burner access on the rear side of
the oven (using a 7 mm socket wrench).
6. You can use the table to determine the new nozzle that you
will need after the gas conversion. See the section entitled
"Technical properties - gas".
7. Insert and tighten the new nozzle.
8. At this point, it is essential to carry out a leak test. To perform
a leak test, see the section entitled "Leak test".
9. Replace the oven burner, making sure that the thermocouple
and ignition plug connections are not damaged. Retighten
the securing screw.
10.At this point, it is important to check the burner flame
formation. See the section entitled "Correct flame formation".
11.Replace the bottom plate.
Replace the nozzle for the grill burner (optional)
1. Open the oven door.
2. Loosen the screw connecting the grill burner to the grill
burner mounting plate and carefully pull the burner straight
out. Make sure that the thermocouple and ignition plug
connections are not damaged. The burner nozzles are now
freely accessible.
3. Release the grill burner nozzle (7 mm socket wrench).
4. You can ascertain which new nozzle is required for the new
gas type using the table. See the section entitled "Technical
properties - gas".
5. Insert and tighten the new nozzle.
6. At this point, it is essential to carry out a leak test. To perform
a leak test, see the section entitled "Leak test".
7. Replace the grill burner, making sure that the thermocouple
and ignition plug connections are not damaged. Retighten
the screws.
8. Slide the seal fully into the burner.
9. At this point, it is important to check the burner flame
formation. See the section entitled "Correct flame formation".






9
Leak test and function test
: Risk of explosion!
Avoid sparking. Do not use an open flame.
Perform the leak test only with a suitable leakage spray.
In the event of a gas leak
Shut off the gas supply.
Ensure that the room affected is well ventilated.
Check the gas and valve connections again. Repeat the leak
test.
The leak test must be performed by two people, in accordance
with the following instructions.
Check the gas connection
1. Open the gas supply.
2. Spray the gas connection with a leakage spray.
If small bubbles or foam form, indicating a gas leak, follow the
instructions in the section entitled "In the event of a gas leak".
Perform the same steps for the part closed with the blind plug.
Checking the burner nozzles
1. Open the gas supply.
Carry out the leak test separately for each nozzle.
2. Carefully close the hole in the burner nozzle to be checked
using your finger or a suitable device.
3. Spray the nozzle with a leakage spray.
4. Press the function selector and turn it anti-clockwise. This
supplies the nozzle with gas.
If small bubbles or foam form, indicating a gas leak, follow the
instructions in the section entitled "In the event of a gas leak".
Checking the bypass valves
1. Open the gas supply.
Carry out the leak test separately for each bypass screw.
2. Carefully close the hole in the burner nozzle to be checked
using your finger or a suitable device.
3. Spray the nozzle in the burner to be checked with a leakage
spray.
4. Push the control knob and turn it anti-clockwise. This supplies
the nozzle with gas.
If small bubbles or foam form, indicating a gas leak, follow the
instructions in the section entitled "In the event of a gas leak".
Checking the oven burner nozzle (option)
1. Open the gas supply.
2. Carefully close the hole in the oven burner nozzle using your
finger or a suitable device.
3. Spray the nozzle with a leakage spray.
4. Press the function selector and turn it anti-clockwise. This
supplies the nozzle with gas.
If small bubbles or foam form, indicating a gas leak, follow the
instructions in the section entitled "In the event of a gas leak".
Check the grill burner nozzle (option)
1. Open the gas supply.
2. Carefully close the hole in the grill burner nozzle using your
finger or a suitable device.
3. Spray the nozzle with a leakage spray.
4. Turn the oven function selector clockwise. This supplies the
nozzle with gas.
If small bubbles or foam form, indicating a gas leak, follow the
instructions in the section entitled "In the event of a gas leak".
Correct flame formation
Burner
The flame formation and temperature development must be
checked for each burner after the appliance is converted to a
different gas type.
In the event of a problem, compare the nozzle values to the
values in the table.
Only for models without safety pilot
1. Ignite the hob burner as described in the operating
instructions.
2. Check the large and small flames for the correct flame
formation. The flame must burn evenly and continuously.
3. Using the burner knob, switch quickly between the large and
small frame. Repeat this process a few times. The gas flame
must not flicker or go out.
Only for models with safety pilot
1. Ignite the hob burner as described in the operating
instructions.
2. Turn the burner knob to the small flame setting.
Check whether the ignition is activated by holding the knob in
the "small flame" position for approximately 1 minute.
3. Check the large and small flames for the correct flame
formation. The flame must burn evenly and continuously.
4. Using the burner knob, switch quickly between the large and
small frame. Repeat this process a few times. The gas flame
must not flicker or go out.
Oven
Lower gas burner or grill burner (optional)
1. Ignite the lower gas burner as described in the operating
instructions.
2. Check the flame formation with the oven door open:
The flame must burn evenly throughout (it may be slightly
uneven in the first few minutes, but after a few minutes, the
flames should burn constantly).
3. To check that the thermocouple is functioning correctly, let
the appliance run for a few minutes.
If necessary, check the settings. If it is not functioning
correctly, replace the bypass screw in the burner.
10
Technical data – Gas
Different types of gas and the corresponding values are listed
here.
Nozzle values for the auxiliary burner
Nozzle values for the standard burner
Nozzle values for the wok burner (optional)
*G20/G25 G20 G20 G25 G25 G30/G31 **G30 G25.1 G27 G30
Gas pressure (mbar) 20/25 20 25 20 25 28-30/37 50 25 20 37
Nozzle (mm) 0.72 0.72 0.68 0.77 0.72 0.50 0.43 0.72 0.77 0.47
Bypass nozzle (mm) 0.50 0.50 0.50 0.50 0.50 0.30 0.30 0.50 0.50 0.30
Max. input power (kW) 1 1 1 1 1 1 1 1 1 1
Min. input power (kW) 0.55 0.55 0.55 0.55 0.55 0.55 0.55 0.55 0.55 0.55
Gas flow at 15 °C and 1013 mbar m³/h 0.095/
0.111
0.095 0.095 0.111 0.111 - - 0.111 0.116 -
Gas flow at 15 °C and 1013 mbar g/h - - - - - 73 73 - - 73
* For France and Belgium
** For G30 (50 mbar), nozzle set HEZ298070 must be ordered from our after-sales service.
*G20/G25 G20 G20 G25 G25 G30/G31 **G30 G25.1 G27 G30
Gas pressure (mbar) 20/25 20 25 20 25 28-30/37 50 25 20 37
Nozzle (mm) 0.97 0.97 0.91 1 0.94 0.65 0.58 0.94 1.00 0.62
Bypass nozzle (mm) 0.58 0.58 0.58 0.58 0.58 0.38 0.38 0.58 0.58 0.38
Max. input power (kW) 1.75 1.75 1.75 1.75 1.75 1.75 1.75 1.75 1.75 1.75
Min. input power (kW) 0.9 0.9 0.9 0.9 0.9 0.9 0.9 0.9 0.9 0.9
Gas flow at 15 °C and 1013 mbar m³/h 0.167/
0.194
0.167 0.167 0.194 0.194 - - 0.194 0.203 -
Gas flow at 15 °C and 1013 mbar g/h - - - - - 127 127 - - 127
* For France and Belgium
** For G30 (50 mbar), nozzle set HEZ298070 must be ordered from our after-sales service.
*G20/G25 G20 G20 G25 G25 G30/G31 **G30 G25.1 G27 G30
Gas pressure (mbar) 20/25 20 25 20 25 28-30/37 50 25 20 37
Nozzle (mm) 1.35 1.35 1.20 1.45 1.40 0.96 0.75 1.40 1.46 0.90
Bypass nozzle (mm) 0.88 0.88 0.88 0.88 0.88 0.55 0.55 0.88 0.88 0.55
Max. input power (kW) 3.6 3.6 3.6 3.6 3.6 3.6 3.6 3.6 3.6 3.6
Min. input power (kW) 1.7 1.7 1.7 1.7 1.7 1.7 1.7 1.7 1.7 1.7
Gas flow at 15 °C and 1013 mbar m³/h 0.342/
0.398
0.342 0.342 0.398 0.398 - - 0.398 0.418 -
Gas flow at 15 °C and 1013 mbar g/h - - - - - 261 261 - - 261
* For France and Belgium
** For G30 (50 mbar), nozzle set HEZ298070 must be ordered from our after-sales service.
11
Nozzle values for the high output burner (optional)
Nozzle values for the gas grill burner in the gas oven
(optional)
Nozzle values for the lower burner on the gas oven with
thermostat (optional)
*G20/G25 G20 G20 G25 G25 G30/G31 **G30 G25.1 G27 G30
Gas pressure (mbar) 20/25 20 25 20 25 28-30/37 50 25 20 37
Nozzle (mm) 1.16 1.16 1.10 1.34 1.21 0.85 0.75 1.21 1.38 0.80
Bypass nozzle (mm) 0.75 0.75 0.75 0.75 0.75 0.46 0.46 0.75 0.75 0.46
Max. input power (kW) 3 3 3 3 3 3 3 3 3 3
Min. input power (kW) 1.3 1.3 1.3 1.3 1.3 1.3 1.3 1.3 1.3 1.3
Gas flow at 15 °C and 1013 mbar m³/h 0.285/
0.332
0.285 0.285 0.332 0.332 - - 0.332 0.348 -
Gas flow at 15 °C and 1013 mbar g/h - - - - - 218 218 - - 218
* For France and Belgium
** For G30 (50 mbar), nozzle set HEZ298070 must be ordered from our after-sales service.
*G20/G25 G20 G20 G25 G25 G30 **G30 G25.1
Gas pressure (mbar) 20/25 20 25 20 25 28-30 50 25
Nozzle (mm) 1.00 1.00 0.98 1.13 1.10 0.70 0.62 1.10
Bypass nozzle (mm) - - - - - - - -
Max. input power (kW) 2.1 2.1 2.1 2.1 2.1 2.1 2.1 2.1
Min. input power (kW) - - - - - - - -
Gas flow at 15 °C and 1013 mbar m³/h 0.2/0.233 0.2 0.2 0.233 0.233 - - 0.233
Gas flow at 15 °C and 1013 mbar g/h - - - - - 153 153 -
* For France and Belgium
** For G30 (50 mbar), nozzle set HEZ298070 must be ordered from our after-sales service.
*G20/G25 G20 G20 G25 G25 G30 **G30 G25.1
Gas pressure (mbar) 20/25 20 25 20 25 28-30 50 25
Nozzle (mm) 1.16 1.16 1.10 1.34 1.21 0.85 0.75 1.21
Bypass nozzle (mm) 0.76 0.76 0.67 0.80 0.70 0.48 0.45 0.70
Max. input power (kW) 3 3 3 3 3 3 3 3
Min. input power (kW) - - - - - - - -
Gas flow at 15 °C and 1013 mbar m³/h 0.285/
0.332
0.285 0.285 0.332 0.332 - - 0.332
Gas flow at 15 °C and 1013 mbar g/h - - - - - 218 218 -
* For France and Belgium
** For G30 (50 mbar), nozzle set HEZ298070 must be ordered from our after-sales service.
*9000696734*
9000696734
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12

Bosch HGG223121M/01 User manual

Type
User manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI