Terzismo PSW 71200 User manual

PSW 71200

!

2

Carefully read this manual for correct and

safe appliance use and for helpful tips on

efficient maintenance.

Only use the washing machine after

carefully reading these instructions. We

recommend you always keep this manua

l

on hand and in good condition

for any

future owners.

Please check that the appliance is delivered

with this instruction manual, warranty

certificate, service centre address and

energy efficiency label. Also check that

plugs, drain hose support hook

and liquid

detergent or bleach tray (only on some

models) are included. We recommend you

keep all these components.

Each product is identified by a unique 16-

character code, also cal

led the “serial

number”, printed on the sticker.

This can

be found inside the door opening. This

code is a unique code for your product that

you will need to register the product

warranty, or if you need to conta

ct the

Customer Service Centre.

This appliance is marked according to

the European directive 2012/19/EU

on Waste Electrical and Electronic

Equipment (WEEE).

WEEE contains both polluting substances (which

can cause negative consequences for the

environment) and basic components (which can

be re-

used). It is important to have WEEE

subjected to specific treatments, in order to

remove and dispose properly all poll

utants, and

recover and recycle all materials. Individuals can

play an important role in ensuring that WEEE

does not become an environmental issue; it is

essential to follow some basic rules:

!

WEEE should not be treated as household

waste;

!

WEEE should be

handed over to the relevant

collection points managed by the municipality or

by registered companies. In many countries, for

large WEEE, home collection could be present.

1. GENERAL SAFETY RULES

2. INSTALLATION

3. PRATICAL HINTS

4. CLEANING AND MAINTENANCE

5. QUICK USER GUIDE

6. CONTROLS AND PROGRAMS

7.

THROUBLESHOOTING AND WARRANTY

Environmental conditions

Contents

!

EN

3

1. GENERAL SAFETY

RULES

!

This appliances is intended to

be used in household and

similar applications such as:

- Staff kitchen areas in shops, offices

and other working environments;

- Farm houses;

- By clients in hotels, motels and

other residential type environments;

- Bed and breakfast type environments.

A different use of this appliance

from household environment

or from typical housekeeping

functions, as commercial use by

expert or trained users, is excluded

even in the above applications. If

the appliance is used in a manner

inconsistent with this it may reduce

the life of the appliance and may

void the manufacturer’s warranty.

Any damage to the appliance or

other damage or loss arising

through use that is not consistent

with domestic or household use

(even if located in a domestic or

household environment) shall not

be accepted by the manufacturer to

the fullest extent permitted by law.

!

This appliance can be used by

children aged from 8 years and

above and persons with reduced

physical, sensory or mental

capabilities or lack of experience

and knowledge if they have been

given supervision or instruction

concerning use of the appliance

in a safe way and understand the

hazards involved.

Children shall not play with the

appliance. Cleaning and user

maintenance shall not be made

by children without supervision.

!

Children should be supervised

to ensure that they do not play

with the appliance.

!

Children of less than 3 years

should be kept away unless

continuously supervised.

!

If the supply cord is damaged, it

must be replaced by a special

cord or assembly available from

the manufacturer or its service

agent.

!

Only use the hose-sets

supplied with the appliance for

the water supply connection

(do not reuse old hose-sets).

!

Water pressure must be between

0.05 MPa and 0.8 MPa.

!

Make sure carpets or rugs do

not obstruct the base or any of

the ventilation openings.

!

The OFF condition is reached

by placing the reference mark

on the programmes control/knob

in the vertical position. Any

other different position of such

control sets the machine in ON

condition (only for models with

programmes knob).

!

4

!

After installation, the appliance

must be positioned so that the

plug is accessible.

!

The maximum load capacity of

dry clothes depends on the

model used (see control panel).

!

To consult the product technical

specification please refer to the

manufacturer website.

!

The technical details (supply

voltage and power input) are

indicated on the product rating

plate

!

Make sure that the electrical

system is earthed, complies

with all applicable law and that

the (electricity) socket is

compatible with the plug of the

appliance. Otherwise, seek

qualified professional assistance.

!

The use of converters, multiple

sockets or extension cords is

strongly advised against

!

Before cleaning or maintaining

the washing machine, unplug

the appliance and turn off the

water tap.

!

Do not pull on the power cord

or appliance to unplug the

machine.

!

Make sure there is no water in

the drum before opening the

door.

!

Do not expose the washing

machine to rain, direct sunlight

or other weather elements.

Protect from possible freezing.

!

When moving, do not lift the

washing machine by the knobs

or detergent drawer; during

transport, never rest the door on

the trolley. We recommend two

people lift the washing machine.

!

In the event of fault and/or

malfunction, turn off the

washing machine, close the

water tap and do not tamper

with the appliance.

Immediately contact the

Customer Service Centre and

only use original spare parts.

Failure to observe these

instruction may jeopardise

appliance safety.

Electrical connections and

safety instructions

WARNING:

water may reach very high

temperatures during the

wash cycle.

!

EN

5

2. INSTALLATION

!

Remove the 2 or 4 transportation

screws (A) on the back and

remove the 2 or 4 flat washers,

rubber bungs and plastic spacer

tubes (B) as illustrated in figure 1.

!

If the washing machine is built-in,

unscrew the 3 or 4 transportation

screws (A) and remove the 3 or 4

flat washers, rubber bungs and

plastic spacer tubes (B).

!

During the removal of the screws

occasionally spacer tubes fall

inside the product, these can be

remove by tilting the product forward

and recovering them from the floor or

inside the base of the machine.

!

Cover the open transportation screw

holes with the 2 or 4 plastic caps

included in the instruction bag.

!

Place the corrugated plastic sheet,

found on top of the appliance during

the unpacking process, into the base

of the appliance as shown in figure 2

(according to the model, consider

version A, B or C).

A

B

1

3

2

1

3

1

2

A

C

B

2

WARNING:

keep packaging materials

away from children.

In some models this operation

will not be necessary, because

the corrugated plastic sheet

will be already placed on the

bottom of the appliance.

!

6

!

Connect the water hose to the water

supply tap (fig. 3)

only using the hose

supplied with the appliance (do not

reuse old hose-sets).

!

SOME MODELS

may include one or

more of the following features:

! HOT&COLD (fig. 4):

water mains connection settings with hot

and cold water for higher energy savings.

Connect the grey tube to the cold water

tap

and the red one to the hot water

tap. The machine can be connected to

the cold water tap only: in this case, s

ome

programs may start a few minutes later.

!

AQUASTOP (fig. 5):

a device located on the supply tube that

stops water flow if the tube deteriorates;

in this case, a red mark will appear in the

window “A

” and the tube must be

replaced. To unscrew the nut,

press the

one-way lock device "B".

!

AQUAPROTECT –

SUPPLY TUBE WITH

GUARD (fig. 6):

Should water leak from the primary

internal tube "A

", the transparent

containment sheath "B

" will contain water

to permit the washing cycle to complete.

At the end of th

e cycle, contact the

Customer Service Centre to replace the

supply tube.

!

The washing machine should be installed

in its final position such that the water fill

hose is not kinked or trapped. The

corrugated drain hose should be inserted

into suitable drain pipe of between 50 cm

and 85 cm height above the floor using

the curved d

rain hose support. If an under

sink connection is used the drain hose

must be routed above the sink overfill

opening to prevent back siphoning. Care

must be taken to avoid kinking or trapping

the drain hose (fig. 7).

3

1

4

B

A

5

B

A

6

min 50 cm

max 85 cm

+2,6 mt

max

max 100 cm

min 4 cm

7

Hydraulic connections

Setting

!

EN

7

!

Level the appliance using the feet as

illustrated in figure 8:

a. turn the nut clockwise to release the

screw;

b. rotate the foot to raise or lower it until it

touches to the floor;

c. lock the foot, screwing in the nut, until it

tightens against to the bottom of the

washing machine.

!

Plug in the appliance.

The detergent draw is split into 3

compartments as illustrated in figure 9:

!

compartment "1": for prewash detergent;

!

compartment “ ”: for special additives,

softeners, starch fragrances, etc.;

!

compartment "2": for washing detergent.

A

B

C

8

2

1

9

WARNING:

contact the Customer Service Centre

should the power cord need

replacement.

Detergent drawer

WARNING:

only use liquid products; the washing

machine is set to automatically dose

additives at each cycle during the last

rinse.

WARNING:

some detergents are not designed for

use in the dispenser drawer but are

supplied with their own dispenser that

is placed in the drum directly.

WARNING:

installation faults are not covered by

the manufacturers warranty.

!

8

3. PRATICAL HINTS

When sorting laundry, make sure:

- have eliminated metallic objects such as

hair clips, pins, coins, from laundry;

- to have buttoned pillow cases, closed

zips, tied loose belts and long robe

ribbons;

- to have removed rollers, hooks or clips

from curtains;

- to have carefully read clothing washing

labels;

- to have removed any persistent stains

using specific detergents.

!

When washing rugs, bedcovers or other

heavy clothing, we recommend you avoid

the spinning cycle.

!

To wash wool, make sure the item can be

machine washed. Check the fabric label.

A guide environmentally friendly and

economic use of your appliance.

Maximise The Load Size

!

Achieve the best use of energy, water,

detergent and time by using the

recommended maximum load size.

Save up to 50% energy by washing a full

load instead of 2 half loads.

Do you need to pre-wash?

!

For heavily soiled laundry only!

SAVE detergent, time, water and

between 5 to 15% energy consumption

by NOT selecting Prewash for slight to

normally soiled laundry.

Is a hot wash required?

! Pretreat stains with stain remover or soak

dried in stains in water before washing to

reduce the necessity of a hot wash

programme. Save energy by using a low

temperature wash programme.

Before using a drying programme

(WASHER-DRYERS)

!

SAVE energy and time by selecting a

high spin speed to reduce the water

content in laundry before using a drying

programme.

Following is a quick guide with tips and

recommendations on detergent use at the

various temperatures. In any case, always

read the instructions on the detergent for

correct use and doses.

Load tips

Helpful suggestions for the user

When washing heavily soiled whites,

we recommend using cotton

programs of 60°C or above and a

normal washing powder (heavy duty)

that contains bleaching agents that at

medium/high temperatures provide

excellent results.

For washes between 40°C and 60°C

the type of detergent used needs to be

appropriate for the type of fabric and

level of soiling.

Normal powders are suitable for “white”

or colour fast fabrics with high soiling,

while liquid detergents or “colour

protecting” powders are suitable for

coloured fabrics with light levels of

soiling.

For washing at temperatures below

40°C we recommend the use of liquid

detergents or detergents specifically

labeled as suitable for low temperature

washing.

For washing wool or silk, only use

detergents specifically formulated for

these fabrics.

!

EN

9

4. CLEANING AND

MAINTENANCE

To clean the washing machine exterior, use

a damp cloth, avoiding abrasives, alcohol

and/or solvents. To maintain a good wash

performance we recommend that the soap

drawer and pump filters are regularly

cleaned. A monthly service wash, using a

proprietary cleaner is also recommended.

!

We recommend you clean the drawer to avoid

accumulating detergent and additive residue.

!

To do this, extract the drawer using slight

force, clean it with running water and

reinsert it in its housing.

!

Ensure the siphon cap is correctly refitted.

!

The washing machine comes with a

special filter able to trap large residue,

such as buttons or coins, which could

clog the drain (according to the model,

consider version A or B).

!

ONLY AVAILABLE ON CERTAIN MODELS:

pull out the corrugated hose, remove the

stopper and drain the water into a

container.

!

Ensure all the water has been emptied

from the drum.

!

Before unscrewing the filter, we

recommend you place an absorbent cloth

under it to keep the floor dry. A small

amount of water will come out of the filter

as you remove it - this is normal.

!

Turn the filter counter-clockwise to the

limit stop.

!

Remove and clean the filter; when

finished, replace it turning it clockwise.

The filter handle will be locked when it is

not possible to turn any further and the

handle is horizontal. Smearing a small

amount of liquid soap on the filter seal will

help refitting.

!

Repeat the previous steps in reverse

order to reassemble all parts.

B

A

!

Should the washing machine be stored in

an unheated room for a long period of

time, drain all water from tubes.

!

Unplug the washing machine.

!

Detach the tube from the drainage system

and clip on the rear of the machine and

lower it, fully draining water into a bowl.

! Secure the drain tube with the drainage

system and clip on the rear of the

machine when finished.

!

Keep the door glass and gasket clean.

Drawer cleaning

Filter cleaning

Suggestions for moves or

prolonged disuse

The manufacturers warranty only

covers faults within the product of a

mechanical or electrical nature. Faults

caused by handling, installation or miss

use are not covered and may incur a

charge for any repair visit to resolve.

!

10

5. QUICK USER GUIDE

This washing machine automatically adjusts

the level of the water to the type and

quantity of washing. This system gives a

reduction in energy consumption and a

saving in washing times.

!

Turn on the washing machine and select

the required program.

!

Adjust the washing temperature if

necessary and press the required "option"

buttons.

!

Press the START/PAUSE button to start

washing.

Should power go out when the washing

machine is running, a special memory

saves the settings and, when power

returns, the machine resumes the cycle

from where it left off.

!

At the end of the programme, the

message "End" will appear on the display

or, on some models, all wash stage

indicator lights will turn on.

!

Turn off the washing machine.

For any type of wash, see the program

table and follow the operating sequence

as indicated.

Water pressure:

min 0.05 Mpa / max 0.8 Mpa

(0.05 MPa dispenses approximately 1 litre

of water in 10 seconds)

Spin r.p.m.: See rating plate.

Power input / Power current fuse amp /

Supply voltage: See rating plate.

6. CONTROLS AND

PROGRAMS

A

DCEF

B

L

M G H I

A Programme selector with OFF

position

B START/PAUSE button

C DELAY START button

D EXTRA RINSE button

E TEMPERATURE SELECTION

button

F SPIN SPEED button

G DELAY START TIME / WASH

STAGE indicator lights

H DOOR LOCKED indicator light

I EXTRA RINSE indicator light

L TEMPERATURE SELECTION

indicator lights

M SPIN SPEED indicator lights

Program selection

Wait until the DOOR LOCKED light has

gone out before opening the door.

Technical data

!

EN

11

!

Press the START/PAUSE button to start

the selected cycle.

!

Once a programme is selected the

programme selector remains stationary on

the selected programme till cycle ends.

!

Switch off the washing machine by

turning the selector to OFF.

!

Press to start the selected cycle

(according to the selected cycle one of

the wash stage indicator lights will

illuminate).

ADD OR REMOVE ITEMS AFTER THE

PROGRAMMES HAS STARTED (PAUSE)

!

Press and hold the START/PAUSE

button for about 2 seconds (some

indicator lights will flash, showing that the

machine has been paused).

!

Wait 2 minutes until the safety device

unlocks the door.

!

After you have added or removed items,

close the door and press the

START/PAUSE button (the programme

will start from where it left off).

CANCELLING THE PROGRAMME

!

To cancel the programme, set the

selector to the OFF position.

!

Appliance start time can be set with this

button, delaying the start by 3, 6 or 9

hours.

!

Proceed as follows to set a delayed start:

- Select a programme.

- Wait until the indicator lights related to

temperature and spin of the programme

selected light up.

- Press the delay start button (each time

the button is pressed the start will be

delayed by 3, 6 or 9 hours respectively

and the corresponding time indicator

light will blink).

Opening the door

A special safety device prevents the

door from being opened immediately

after the end of the cycle.

Wait for 2 minutes after the wash

cycle has finished and the "Door

Security" light has gone out before

opening the door.

PROGRAMME selector with OFF

position

When you select a programme the

indicator lights related to temperature

and spin of that cycle will light up.

N.B.: To switch the machine off, turn the

programme selector to the OFF

position.

The programme selector must be

returned to the OFF position at the end

of each cycle or when starting a

subsequent wash cycle prior to the next

programme being selected and started.

START/PAUSE button

Close the door BEFORE selecting the

button START/PAUSE.

When the START/PAUSE button has

been pressed, the appliance can take

few seconds before it starts working.

Before you open the door, please

check water level is below the door

opening to avoid flooding.

DELAY START button

!

12

- Press START/PAUSE button to

commence the delay start operation (the

indicator light associated with the

selected delay start time stops blinking

and remains on). At the end of the

required time delay the programme will

start.

!

It is possible to cancel the delay start by

turning the programme selector to OFF.

If there is any break in the power supply

while the machine is operating, a special

memory stores the selected programme

and, when the power is restored, it

continues where it left OFF.

!

This option allows you to add one rinse at

the end of the washing cycle and is useful

for people with delicate and sensitive

skin, for which a small amount of

detergent residue can cause irritations or

allergies.

!

It is advisable to also use this function for

the children clothes and for the washing

of heavily soiled items, which requires a

lot of detergent to be used, or for the

washing of toweling items whose fibres

mostly have the tendency to hold the

detergent.

!

This button allows you to change the

temperature of the wash cycles.

!

It is not possible to raise the temperature

over the maximum allowed for the

programme, in order to protect the

fabrics.

!

If you want carry out a cold wash all the

indicators must be off.

!

By pressing this button, it is possible to

reduce the maximum speed, and if you

wish, the spin cycle can be cancelled.

!

If the label does not indicate specific

information, it is possible to use the

maximum spin expected in the program.

!

To reactivate the spin cycle press the

button until you reach the spin speed you

would like to set.

!

It is possible to modify the spin speed

without pausing the machine.

The option buttons should be

selected before pressing the

START/PAUSE button.

EXTRA RINSE button

If the option is not compatible with the

selected programme, the relevant

indicator light first flashes and then

goes off.

TEMPERATURE SELECTION

button

SPIN SPEED button

To prevent damage to the fabrics, it is

not possible to increase the speed

over the maximum allowed for the

programme.

An over dosing of detergent can

cause excessive foaming. If the

appliance detects the presence of

excessive foam, it may exclude the

spinning phase or extend the duration

of the program and increase water

consumption.

The machine is fitted with a special

electronic device, which prevents the

spin cycle should the load be

unbalanced. This reduces the noise

and vibration in the machine and so

prolongs the life of your machine.

!

EN

13

!

Each time the DELAY START button is

pressed the indicator lights show how

many hours of delay you chosen (3, 6 or

9 hours) and the countdown until the end

of it.

!

When a programme is running, the

indicator lights will light in sequence to

indicate the current phase:

main wash

rinse

spin

!

The indicator light is illuminated when the

door is fully closed.

!

When START/PAUSE is pressed on

the machine with the door closed, the

indicator will flash momentarily and then

illuminate.

!

A special safety device prevents the door

from being opened immediately after the

end of the cycle. Wait for 2 minutes after

the wash cycle has finished and the

DOOR LOCKED light has gone out before

opening the door. At the end of the cycle

turn the programme selector to OFF.

The indicator light will light up when the

button is pressed.

If the option is not compatible with the

selected programme, the relevant indicator

light first flashes and then goes off.

This show the washing temperature of the

selected programme that can be changed

(where allowed) by the relevant button.

If you want carry out a cold wash all the

indicators must be off.

This show the spin speed of the selected

programme, you can reduce or cancel by the

relevant button.

DELAY START TIME / WASH

STAGE indicator lights

DOOR LOCKED indicator light

Close the door BEFORE selecting the

START/PAUSE button.

If the door is not properly closed,

the light will continue to flash for

about 7 seconds, after which the

start command will be automatically

cancelled. In this case, close the

door in the proper way and press

the

START/PAUSE button.

EXTRA RINSE indicator light

WASH TEMPERATURE indicator

lights

SPIN SPEED indicator lights

!

14

PROGRAM

(MAX.)

*

1)

2

1

(see control panel)

(MAX.)

2

1

1,5 2 2,5 2,5 2,5 2,5 2,5 3

30°

1,5 2 2,5 3 3 3,5 3,5 4

60°

2,5 3 3,5 4 4,5 5 5,5 6

60°

1 1 1 2 2 2 2 2,5

30°

2 2 2,5 2,5 2,5 2,5 2,5 3

40°

2,5 2,5 3 3,5 4 4 4,5 5

30°

2,5 3 3,5 4 4,5 5 5,5 6

40°

- - - - - - - -

-

- - - - - - - -

-

3,5 4 4,5 5,5 6 6,5 7 8

60°

5 6 7 8 9 10 11 12

20°

**

5 6 7 8 9 10 11 12

60°

5 6 7 8 9 10 11 12

60°

5 6 7 8 9 10 11 12

90°

2,5 3 3,5 4 4,5 5 5,5 6

30°

Table of programmes

!

EN

15

Please read these notes:

* Maximum load capacity of dry clothes,

according to the model used (see control

panel).

1) When a programme is selected,

on the display is shown the

display shows the recommended

wash temperature that can be

reduced (where allowed) by the

relevant button.

** STANDARD COTTON PROGRAMMES

ACCORDING TO (EU) No 1015/2010 and

No 1061/2010.

COTTON PROGRAMME WITH A

TEMPERATURE OF 60°C.

COTTON PROGRAMME WITH A

TEMPERATURE OF 40°C.

These programmes are suitable to

clean normally soiled cotton laundry and

they are the most efficient programmes

in terms of combined energy and water

consumptions for washing cotton

laundry.

These programmes have been

developed to be compliant with the

temperature on the wash label on the

garments and the actual water

temperature may slightly differ from the

declared temperature of the cycle.

!

16

To clean different types of fabrics and

various levels of dirt, the washing machine

has specific programs to meet every need

of washing (see table of programmes).

Rapid 30 Min.

A complete washing cycle (wash, rinse and

spin). This programme is particularly suited

to slightly d

irty cottons and mixed fabrics.

With this programme it is recommended to

use only 20% of the detergent normally

used to avoid waste.

Daily 59 Min.

This specially designed programme maintains

the high quality wash performance whilst

greatly reducing the wash time. The

programme is designed for a reduced load

(see table of programmes).

Synthetics

The washing and rinsing optimise

the speed

and rhythm of t

he drum action and water

levels. The gentle spin, ensures a

reduced

formation of creases in the fabric.

Wool & Handwash

This program performs a wash cycle

dedicated to the wool fabrics that can be

washed in a washing machine, or the

articles to be washed by hand.

Delicates

This program has reduced periods of drum

rotation during the cycle and is particularly

suitable or washing delicate fabrics

. The

wash cycle and rinses are carried out with a

high level of water to ensure the best

performance.

Sports

This programme is specially designed to

wash mixed sportswear fabrics that cannot

be washed on hotter programmes and is

designed to remove the dirt and staining

created by participation in sports activities.

Dark Colours

Program designed to mix all dar

k garments and to

avoid the loss of colour and the formation of creases.

We recommend the use of liquid detergent.

Rinse

This program performs 3 rinses with an

intermediate spin (which can be reduced or

excluded by using the appropriate button) . It

is

used for rinsing any type of fabric, for

example after a wash carried out by hand.

Drain & Spin

The program completes the drain and a

maximum spin. It is possible to delete or

reduce the spin with the SPIN SPEED button.

Baby

This program allows you to wash all baby

clothes getting a perfect clean and

sanitizing effect, setting the temperature at

60°C minimum.

To optimize the result of the sanitizing effect

we recommend the use of powder detergent.

Eco 20°C

This innovative pro

gramme, allows you to wash

different fabrics and colours together, such as

cottons, synthetics and mixed fabrics at only

20°C and provides an excellent cleaning

performance. Consumption on this program is

about 40% of a conventional 40°C. cottons

wash.

Cotton

This program is suitable to clean normally soiled

cotton laundry and it is the most efficient program

in terms of combined energy and water

consumptions for washing cotton laundry.

Whites + Prewash

This programme has been designed to

remove the stronger stains from cotton

white clothes. The prewash

guarantees the

tough dirt removal. Add into compartment

"1"

a quantity of detergent equal to 20% of

that used for main wash.

Whites

An intensive wash. The final spin at maximum

speed gives more efficient removal.

Shirts

The washing cycle is optimized to reduce

the creation of

creases, keeping an

excellent

washing performance. It is also

possible to further reduce the spin speed, to

ensure an easier ironing.

Programmes selection

!

EN

17

7. THROUBLESHOOTING AND WARRANTY

If you believe the washing machine is not working correctly, consult the quick guide

provided below which includes some practical tips on how to fix the most common

problems.

ERROR CODE FORMAT

Error shown Possible causes and practical solutions

E2 (with display)

2 flashes of the LEDs

(without display)

The machine cannot load water.

Make sure the water supply tap is open.

Make sure the water supply hose isn’t bent, kinked or trapped.

Make sure the drain pipe is at the proper height (see installation section).

Close the water supply tap, unscrew the filler hose from the back of

the washing machine and make sure the “anti-sand” filter is clean

and not blocked.

Check that the filter is not clogged or that there are no foreign bodies

inside the filter compartment that can obstruct the proper flow of

water.

E3 (with display)

3 flashes of the LEDs

(without display)

The washing machine does not drain water.

Check that the filter is not clogged or that there are no foreign bodies

inside the filter compartment that can obstruct the proper flow of

water.

Make sure the drain hose isn’t bent, kinked or trapped.

Make sure the home drainage system is not blocked and is allowing

water to flow through without obstruction. Try to drain the water in the sink.

E4 (with display)

4 flashes of the LEDs

(without display)

There is too much foam and/or water.

Ensure the correct amount of detergent is being used and the

detergent is designed for use in a washing machine.

E7 (with display)

7 flashes of the LEDs

(without display)

Door problem.

Make sure the door is correctly closed.

Make sure the clothes inside the drum are not preventing the door

from closing fully.

If the door is locked, turn off and unplug the washing machine from

the electrical supply socket, wait 2-3 minutes and reopen the door.

Any other code

Turn off and unplug the washing machine, wait a minute. Turn on the

machine and restart a program. If the error occurs again contact an

Authorised Customer Service Centre directly.

!

Models with a display: the error is shown by a number preceded by the letter “E”

(example: E2 = Error 2).

!

Models without display: an error is shown by a sequence of flashes of every LED.

The error code is shown by the number of flashes followed by a pause of 5 seconds

(example: two flashes – pause 5 seconds – two flashes – repeating = Error 2).

!

18

OTHER ANOMALIES

Problem Possible causes and practical solutions

The washing machine

does not work / start

Make sure the product is plugged into a working supply socket.

Make sure power is on.

Make sure the wall socket is working, testing it with another

appliance such as a lamp.

The door may not be correctly closed: open and close it again.

Check whether the required program was correctly selected and the

start button pressed.

Make sure the washing machine is not in pause or time delay mode.

Water leaked on the

floor near the

washing machine

This may be due to a leak from the seal between the tap, supply

hose and fill valve; in this case, replace it and tighten the hose

connections correctly.

Make sure the front filter is correctly closed.

The washing machine

does not spin

The machine is fitted with a detection system that protects the load

and product from damage if the load is not balanced before spinning.

This may result in:-

• The machine attempts to balance the load, increasing the time of

spin.

• Reduction of the speed of spin to decrease vibrations and noise.

• The spin cycle aborting to protect the machine and load.

If this is experienced remove the load de-tangle it, reload it and

restart the spin program.

This could be due to the fact that water has not been completely

drained: wait a few minutes. If the problem persists, see Error 3

section.

Some models include a "no spin" function: make sure it is not

selected.

Check which options are selected and their effect on the spin cycle.

Excessive detergent can impede the spin cycle, ensure the correct

amount of detergent is being used.

Strong vibrations /

noises are heard

during the spin cycle

The washing machine may not be fully levelled: if necessary, adjust

the feet as indicated in the specific section.

Make sure transport screws, rubber bungs and spacer tubes were

removed.

Make sure there are no foreign objects inside the drum (coins,

hinges, buttons, etc…).

The standard manufacturer warranty covers faults caused by electrical or

mechanical faults in the product due to an act or omission of the manufacturer. If

a fault is found to be caused by factors outside the product supplied, miss-use or

as a result of the instructions on use not being followed, a charge may be

applied.

!

EN

19

The use of ecological detergents without

phosphates may cause the following effects:

- cloudier rinse drain water: This effect is

tied to the suspended zeolites which do

not have negative effects on rinse

efficiency.

- white powder (zeolites) on laundry at

the end of the wash: this is normal, the

powder is not absorbed by fabric and

does not change its colour.

To remove the zeolites, select a rinse

programme. In the future consider using

slightly less detergent.

- foam in the water at last rinse: this

does not necessary indicate poor rinsing.

Consider using less detergent in future

washes.

- abundant foam: This is often due to the

anionic surfactants found in the

detergents which are hard to eliminate

from laundry.

In this case, do not re-rinse to eliminate

these effects: it will not help at all.

We suggest conducting a maintenance

wash using a proprietary cleaner.

If the problem persists or if you suspect a

malfunction, immediately contact an

Authorised Customer Service Centre.

It is always recommended to use original

spare parts, that are available at our

Authorised Customer Service Centres.

By placing the

mark on this

product, we are confirming compliance to

all relevant European safety, health and

environmental requirements which are

applicable in legislation for this product.

The manufacturer declines all

responsibility for any printing errors in

the booklet included with this product.

Moreover, it also reserves the right to

make any changes deemed useful to its

products without changing their essential

characteristics.

Warranty

The product is guaranteed under the

terms and conditions stated on the

certificate included with the product. The

certificate has to be stored so as to be

shown to the Authorized Customer

Service Centre in case of need. You can

also check the warranty conditions on

our web site. To obtain assistance,

please fill in the form on-line or contact

us at the number indicated on the

support page of our web site.

Please record the following product information

Model

Serial No.

Name of the franchiser

Date of purchase

The continuous improvement of products,such as function is changed,without prior notice,

if there are any questions,please contact customer service,Sorry for the inconvenience,

please forgiveness.

Proudly Serviced by:

Service E-mail:8210service gilman-group.com

@

Please register now at:www.toolbox.hk

Website:www.gilman-group.com

S49100000029

ToolBox Customer Service Centre:

Terzismo PSW 71200 User manual

Terzismo PSW 71200 User manual

Related papers

Other documents