VISA BT302 Owner's manual

Brand
VISA
Model
BT302
Category
TV signal amplifiers
Type
Owner's manual

This manual is also suitable for

VISA BT302 I

The VISA BT302 I is an indoor line amplifier that can be used to amplify the signals from the antenna where they are weak or in case of losses in the distribution of signals inside your home, without the need to operate on the existing TV installation.

It has two adjustable gain controls, one for VHF and one for UHF signals. The maximum output level is 102dBuV and the noise figure is 5dB.

To install the amplifier, simply insert the antenna cable into the "IN" connector and connect a cable between the "OUT" connector and your TV or decoder. Then insert the plug of the power supply into the electrical outlet and connect the connector to the amplifier.

VISA BT302 I

The VISA BT302 I is an indoor line amplifier that can be used to amplify the signals from the antenna where they are weak or in case of losses in the distribution of signals inside your home, without the need to operate on the existing TV installation.

It has two adjustable gain controls, one for VHF and one for UHF signals. The maximum output level is 102dBuV and the noise figure is 5dB.

To install the amplifier, simply insert the antenna cable into the "IN" connector and connect a cable between the "OUT" connector and your TV or decoder. Then insert the plug of the power supply into the electrical outlet and connect the connector to the amplifier.

DESCRIZIONE TECNICA:
Amplificatore di linea da interno, può essere utilizzato per amplificare i segnali provenienti dall’antenna
qualora risultino deboli o nel caso di perdite nella distribuzione dei segnali all’interno dell’abitazione, senza
la necessità di intervenire sull’impianto esistente.
Per la sua semplice installazione procedere come segue (vedi FIG.1):
1) inserire il cavo della discesa d’antenna nel connettore “IN” (tipo F) dell’amplificatore (utilizzare
l’adattatore optionale) .
2) Collegare un cavo tra il connettore di uscita “OUT” (tipo F) dell’amplificare (utilizzare
eventualmente l’adattatore optionale) con il TV o con il decoder DVB-T (digitale terrestre).
2a) Collegare la seconda uscita “OUT” (tipo F) dell’amplificatore (utilizzare l’eventuale l’adattatore
optionale) ad un secondo apparato TV o decoder DVB-T (digitale terrestre). Qualora non utilizzata la
seconda uscita “OUT” può restare scollegata è inoltre possibile usare una delle due uscite
indistintamente.
3) Inserire la spina elettrica dell’alimentatore (5V DC) alla presa della corrente e collegare il connettore
all’amplificatore (5V DC IN). Si accenderà il led blu sul frontale dell’amplificatore.
4) Accendere il TV e/o il decoder DVB-T.
5) Regolare ora i guadagni dell’amplificatore agendo sui cursori (1 e 2 della FIG.1) fino ad ottenere
una ricezione ottimale.
I
GB
TECHNICAL DESCRIPTION:
Indoor Line Amplifier can be used to amplify the signals from the antenna where they are weak or in
case of losses in the distribution of signals inside your home, without the need to operate on the existing
TV installation.
To its simple installation proceed as follows (see Fig.1):
1) Insert the antenna cable into the connector "IN" (type F) of the amplifier (using the optional adapter).
2) Connect a cable between the connector output "OUT" (type F) of the amplifier (using the optional
adapter if necessary) with the TV or with the decoder DVB-T (digital terrestrial).
2a) Connect the second output “OUT” (type F) of the amplifier (using the optional adapter if necessary)
to a second TV device or decoder DVB-T (digital terrestrial). If not used, the second exit "OUT" can remain
disconnected, it’s also possible to use one of two outputs equally
3) Insert the plug of the power supply (5V DC) to the electrical outlet and connect the connector to the
amplifier (5V DC IN). It will light the blue LED on the front of the amplifier.
4) Turn on your TV and / or the decoder DVB-T.
5) Adjust now the amplifier gains by acting on cursors (1 and 2 of FIG.1) until obtaining optimal reception.
DESCRIPTION TECHNIQUE:
L’Amplificateur d’intérieur est utilisé pour amplifier les signaux de l'antenne en cas de mauvaise réception
ou en cas de pertes dans la distribution de signaux à l’intérieur de la maison, sans la nécessité d'opérer sur
l'installation existante
FR
Pour la simple installation, procédez comme suit (voir Fig.1):
1) Insérez le câble d'antenne au connecteur «IN» (type F) de l'amplificateur (Utilisez l'adaptateur optionnel)
2) Branchez un câble sur le connecteur de sortie "OUT" (type F) de l'amplificateur (utilisez
éventuellement l’adaptateur optionnel) au TV ou au décodeur DVB-T (numérique terrestre).
2a) Branchez la deuxième sortie "OUT" (type F) de l’amplificateur (utilisez éventuellement l’adaptateur
optionnel) à un deuxième TV ou un décodeur DVB-T (numérique terrestre). Si la deuxième sortie
"OUT" ne vient pas utilisée elle peut rester déconnectée, il est aussi possible d’utiliser également une
des deux sorties.
3) Insérez la fiche électrique de l'alimentation (5V DC) à la prise électrique et branchez le connecteur à
l'amplificateur (5V DC IN). Une LED bleue s’allumera sur l'amplificateur.
4) Allumez votre TV et / ou le décodeur DVB-T.
5) Régler maintenant les gains de l'amplificateur en agissant avec les curseurs (1 et 2 de FIG.1) jusqu’à
l’obtention d’une réception optimale.
SPECIFICHE TECNICHE:
1 INPUT/ Ingresso (VHF-UHF)
2 OUTPUT / Uscite
GAIN / Guadagni (dB):
UHF 28dB (adjusment / regolazione +/- 28dB)
VHF 23dB (adjusment / regolazione +/- 23dB)
NOICE/Figura di Rumore:
5dB
Max Output Level/Livello Massimo di uscita:
102dbuV
Power Supply / Alimentazione :
230V AC / 50Hz
Impedence / impedenza:
75 OHM
3
2
1
INPUT
OUTPUT
Decoder
DVB-T
5V DC
POWER
SUPPLY
BT 30
1-2
220 V ~
5V DC IN
1= GAIN Reg. VHF
2= GAIN Reg. UHF
3= Led "ON"
TV / DTV
Decoder
DVB-T
TV / DTV
FIG.1 cod.771857
  • Page 1 1
  • Page 2 2

VISA BT302 Owner's manual

Brand
VISA
Model
BT302
Category
TV signal amplifiers
Type
Owner's manual
This manual is also suitable for

VISA BT302 I

The VISA BT302 I is an indoor line amplifier that can be used to amplify the signals from the antenna where they are weak or in case of losses in the distribution of signals inside your home, without the need to operate on the existing TV installation.

It has two adjustable gain controls, one for VHF and one for UHF signals. The maximum output level is 102dBuV and the noise figure is 5dB.

To install the amplifier, simply insert the antenna cable into the "IN" connector and connect a cable between the "OUT" connector and your TV or decoder. Then insert the plug of the power supply into the electrical outlet and connect the connector to the amplifier.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

in other languages

Related papers

Other documents