Scholtes LFD S3 XL60HZ Operating Instructions Manual

EN

DISHWASHER

FZ 102 P.1/HA

FZ 102 P.1 IX/HA

FZ 1022 P.1/HA

FZ 1022 P.1 IX/HA

FZ 1022 P.1 F/HA

FZ 1022 P.1 IX F/HA

FZ 102 P.1 F/HA

FZ 102 P.1 IX F/HA

OPERATING

INSTRUCTIONS

LTE S3 XL60HZ

LFD S3 XL60HZ

English, 1

GB

Contents

Introduction, 2

Safety information, 3

Installation material, 7

Kit supplied with dishwasher, 7

Dimensions of dishwasher, 8

Installation and hook-up, 8

Leveling, 8

Connections, 9

Commissioning, 13

Testing, 15

Operating instructions, 16

Cleaning and user-maintenance, 20

Technical data, 23

Description and use of the controls, 24

Energy saving and environmental respect, 27

Removing the dishes, 27

Troubleshooting, 28

Service, 29

Warranty, 30

Français, 31

FR

Español, 63

ES

2

EN

1 INTRODUCTION

Thank you for choosing one of our products.

To install and use this dishwasher correctly and safely,

please read this manual carefully. The manual is divided

into sections giving you a step-by-step guide to

installation of the appliance. This user-friendly manual

will provide answers to all your questions about

installation of the dishwasher.

Following the cleaning instructions provided here will keep

dishwasher performance at peak levels in the long term.

For any other information about use and maintenance of the

dishwasher, read the enclosed general manual carefully.

This manual comprises the following sections:

INTRODUCTION: general information about the manual.

WARNINGS: a list of warnings concerning safety during

installation.

INSTALLATION INSTRUCTIONS: for the qualified

technician who must carry out the installation, hook-up

and testing of the appliance.

USER INSTRUCTIONS: useful advice is provided for the

use of racks, spray arms, containers and filters and on

using the washing programs and information about all

the dishwasher functions.

INTRODUCTION

Nomenclature of figures and tables:

The progressive number of each figure is shown in the

bottom righthand corner of the relative box. An example

of a progressive number is "Fig. 4-01", where the first

number (4) indicates the section to which the figure

belongs, while the second number (01) indicates the

progressive number of the figure in section 4 (Fig. 4-01 is

the first figure in section 4). The tables are numbered in

the same way, bearing in mind that "Tab." is used instead

of "Fig." (e.g.: Tab. 4-01 is the first table in section 4). If a

table occupies more than one page, a letter is added

after the progressive number (e.g.: "Tab. 4-01a", Tab. 4-

01b").

DANGER.

This symbol highlights information

and warnings which, if not observed, may

compromise personal safety or damage the

appliance.

DANGER OF ELECTROCUTION.

This

symbol highlights information and warnings

of an electrical nature which, if not observed,

may compromise personal safety or damage

the appliance.

This symbol highlights general information

and warnings.

EN

3

IMPORTANT SAFETY

INSTRUCTION

2 IMPORTANT SAFETY INSTRUCTION

(Save these instructions)

This manual forms an integral part of the appliance

and must therefore be kept intact together with the

machine. before using the appliance, carefully read all

the instructions contained in this manual.

Installation must be performed by a qualified technician,

in compliance with the regulations in force. this

appliance is intended for domestic use, and complies

with the directives currently in force, including the

prevention and elimination of radio frequency

interference.

The appliance is designed for the following purpose:

washing and drying of dishes; any other use shall be

considered improper. The manufacturer declines all

responsibility for uses other than those described

above.

Only use detergents specially formulated for

dishwashers. Do not use detergents formulated for

washing dishes by hand. Only use rinse-aid specially

formulated for domestic dishwashers.

Do not inhale or swallow detergent as this may cause

burns and/or permanent damage to the nose, mouth and

throat, and even leading to suffocation; keep detergent

away from your eyes. If one of the above situations

occurs, seek medical assistance immediately. To prevent

children from coming into contact with detergent, fill the

dishwasher just before starting the work program and

then keep the detergent out of the reach of children.

This dishwasher must be used by adults. Use by

persons with reduced mental and/or physical

capabilities is only permitted under the supervision of a

person responsible for their safety.

Do not allow children to approach and/or play in or on

the dishwasher. The appliance may contain residues of

detergent which can cause permanent damage to the

eyes, mouth and throat, as well as possible death by

suffocation; if the above occurs, seek medical

assistance immediately. Beware; it is possible for

children to get trapped inside the dishwasher!

Do not introduce items in heat-sensitive plastic, such as

disposable cutlery or plates, as these may become

deformed. Do not wash objects in plastic unless they are

marked "dishwasher proof" or the like.

For unmarked objects, follow the instructions of the

manufacturer; if no information is available, do not wash

these objects in the dishwasher.

In certain situations, hydrogen may be generated inside

a hot water system that has not been used for over two

weeks. Hydrogen is an explosive gas. If the hot water

system has not been used for two weeks or more, open

all the hot water taps and allow the water to run for a few

minutes before using the dishwasher.

This will discharge any hydrogen buildups.

As this gas is flammable, do not smoke or use naked

flames while performing this operation.

Leaning or sitting on the dishwasher door when open

may cause the appliance to overturn, putting people

at risk. Never leave the dishwasher door open;

people might trip over it.

Do not lean against or stand on the dishwasher racks.

Knives or other sharp-ended cooking utensils must be

placed in the cutlery basket blade-down, or laid

horizontal in the upper rack.

Take care not to cut yourself and ensure that they do not

project from the rack. Position sharp/pointed objects so

as to prevent them from damaging the door gaskets.

Do not tamper with the dishwasher controls.

This appliance must be grounded. in case of a

malfunction of fault, the earth reduces the risk of

electrocution by providing the electrical current with an

alternative, less resistant path.

4

EN

This appliance is fitted with a supply cord containing an

ground wire and plug. fit the plug into a suitable socket,

installed and grounded in compliance with the laws in

force in the country of installation.

An incorrectly connected ground wire may generate the

risk of electrocution. if in doubt as to the correct earthing

of the appliance, call in a qualified electrician or the

technical assistance service. do not change the plug

attached to the appliance. if the plug is not suitable for the

socket, call in a qualified electrician to fit a suitable plug.

Installation, repairs and servicing must be performed

by qualified and authorized technicians.

As well as invalidating the warranty, work carried out by

unauthorized persons may generate hazards. Installation

must be performed in compliance with all the directives

in force in the country of installation and, if these do not

exist: in the united states the national electric code; in

canada the canadian electric code c22.1 - latest edition/

provincial and municipal codes and/or local codes.

The name plate featuring the technical data, serial

number and markings is visibly positioned on the inner

edge of the door. The nameplate on the inner edge of

the door must never be removed.

This appliance is not suitable for use on boats, caravans

or the like. dishwashers certified for domestic use are not

suitable for authorised food factories.

Check that the voltage, frequency and protection of the

domestic mains power supply match the ratings on the

name plate of the appliance.

Two people wearing safety gloves are required to lift

the dishwasher.

Do not leaving discarded packaging materials

unsupervised within the home. separate the various

packaging materials and take them to the nearest sorted

waste collection centre. keep children, physically and/or

mentally impaired adults, and animals away from

packaging waste; danger of suffocation.

Before proceeding with installation, disconnect the

mains power supply from the work area.

During installation, take care not to injure yoursel 0f on

the sharp edges of the appliance; wear safety gloves.

The appliance must be provided with a ground

connection in accordance with the electrical safety

regulations in force. if in doubt, have the system checked

by a qualified electrician.

The manufacturer declines all responsibility for

damage to persons or property resulting from the

failure to ground the appliance or from a defective

ground connection.

Do not use appliances which have been damaged

during transit! if in doubt, consult your dealer. the

appliance must be installed and connected in

accordance with the instructions provided by the

manufacturer or by a qualified technician.

Do not operate the dishwasher unless all the outer

panels have been positioned correctly. Immediately after

installation, briefly test the appliance following the

instructions indicated below. If the dishwasher fails to

operate correctly, disconnect it from the electrical power

supply and call the nearest technical service centre.

Do not attempt to repair the appliance.

EN

5

Do not use extension cords, adaptors or shunt

connections in order to avoid the possibility of

overheating or burning, with consequent fire hazard.

Always switch off the dishwasher after each use to

avoid wasting electricity.

In the event of a fault, disconnect the dishwasher from

the electrical power supply and shut off the water tap.

Do not introduce solvents such as alcohol or turpentine

which may cause an explosion.

Do not pour powder and/or liquid detergent into the rinse-

aid container as this will damage the container. Do not pour

powder and/or liquid detergent into the waster softener tank

as this will damage the tank. Do not use industrial

detergents as this may damage the appliance and/or

trigger violent chemical reactions (e.g. explosive gas).

Do not drink the water residues which may be present

inside the dishes or dishwasher.

Do not operate the dishwasher unless all the outer

panels have been positioned correctly.

Aquastop models; the aquastop device prevents

flooding in the event of a water leak. When the aquastop

device is tripped (the error is indicated on the display),

call in a qualified technician to identify and repair the

fault. In models equipped with the aquastop device,

there is a solenoid valve inside the water intake hose. Do

not cut the hose and do not allow the solenoid valve

to drop into water. In the event of damage to the water

intake hose, disconnect the appliance from the electrical

power supply and from the water supply. Immediately

after installing the dishwasher, perform a quick test of the

appliance (see "installation" manual). If the dishwasher

fails to operate correctly, disconnect it from the electrical

power supply and call the nearest technical service

centre. Do not attempt to repair the appliance.

The dishwasher meets all the requirements set out by the

regulations in force concerning safety and electrical

equipment. Any technical checks should be conducted

exclusively by a trained and authorized technician:

Repairs carried out by unauthorized persons will

invalidate the warranty, as well as posing a potential

hazard to the user.

Before cleaning or servicing the appliance, remove the

plug or turn off the multi-pole switch.

Remove the washing compartment door and disconnect

the mains power supply when removing the old

dishwasher for maintenance or disposal.

The symbol on the product, or on the documents

accompanying the product, indicates that this appliance

may not be treated as household waste. Instead it shall

be handed over to the applicable collection point for the

recycling of electrical and electronic equipment.

Disposal must be carried out in accordance with local

environmental regulations for waste disposal. For more

detailed information about treatment, recovery and

recycling of this product, please contact your local city

office, your household waste disposal service or the

shop where you purchased the product.

By ensuring this product is disposed of correctly, you will

help prevent potential negative consequences for the

environment and human health.

6

EN

Do not load dishes that are soiled with ash, wax or

paints.

Do not introduce items in heat-sensitive plastic, such as

disposable cutlery or plates, as these may become

deformed. do not wash objects in plastic unless they are

marked "dishwasher proof" or the like.

for unmarked objects, follow the instructions of the

manufacturer; if no information is available, do not wash

these objects in the dishwasher.

Do not introduce animals into the dishwasher.

When opening the dishwasher door during a cycle there

is a risk of scalding due to the heat contained inside; do

not get in the way of the steam leaving the appliance

and do not touch the components inside.

Wait 20 minutes after the end of the washing cycle or

after interrupting it before removing the dishes in order to

allow them to dry.

The manufacturer declines all responsibility for

damage to persons, animals or property resulting

from failure to observe the above precautions, from

tampering with even a single component of the

appliance, or from the use of unoriginal spare parts. If

in doubt about the contents of this manual, contact

the technical assistance service.

EN

7

INSTALLATION

INSTRUCTIONS

3 INSTALLATION MATERIAL

To install the dishwasher correctly, the following materials

are required:

• Phillips screwdriver (ref. A fig. 3-01);

• spirit level (ref. B fig. 3-01);

• tape measure (ref. C fig. 3-01);

• compass saw (ref. D fig. 3-01);

• pencil (ref. E fig. 3-01);

• file (ref. F fig. 3-01);

• 13 mm open-ended wrench (ref. G fig. 3-01);

• plumbing pliers (ref. H fig. 3-01);

• drill (ref. I fig. 3-01);

• safety gloves (ref. L fig. 3-01).

Fig. 3-01

3.1 Kit supplied with dishwasher

(models LTE)

The kit supplied with the dishwasher comprises:

• adhesive steam guard (ref. A fig. 3-02);

• 1 steel steam guard (ref. B fig. 3-02);*

• 1 template for door panel (ref. C fig. 3-02);

• 2 hooks for door panel (ref. D fig. 3-02);

• 8 screws for securing the door panel hooks (ref. E fig.

3-02);

• 2 screws for securing the door (ref. F fig. 3-02);

• 2 screws for fixing the dishwasher to the adjacent

walls (ref. G fig. 3-02);

• 2 screw caps (ref. H fig. 3-02).

• 2 adjustment feet (only for some models) (ref. I fig. 3-

02);

• 2 nuts (only for some models) (ref. L fig. 3-02);

• 2 washers (only for some models) (ref. M fig. 3-02).

Fig. 3-02

* The adhesive protection is suitable for kitchens with

worktops that do not allow the steel protection to be

fixed with screws (e.g.:+ marble or masonry), but it can

be also used with other materials.

8

EN

4 DIMENSIONS OF DISHWASHER

(See fig. 4-01)

Model A (height) B (width) C (depth)

LTE

85,8 cm ÷ 91 cm

33,81" ÷ 35-55/64”

59.7 cm ÷ 59.9 cm

23-1/2” ÷ 23-37/64”

54,7 cm

21,55”

LFD

85,8 cm ÷ 91 cm

33,81" ÷ 35-55/64”

59.7 cm ÷ 59.9 cm

23-1/2” ÷ 23-37/64”

54,7 cm

21,55”

Tab. 4-01

Fig. 4-01

5 INSTALLATION AND HOOK-UP

During installation, take care not to injure yourself on the

sharp edges of the appliance.

Remove the polystyrene rack blocks. Position the

appliance in the chosen installation position. The sides

and rear of the appliance can lie against kitchen units or

walls. If the dishwasher is installed next to a heat source,

separate it with a heat insulating panel in order to

prevent overheating and malfunctions. To assure stability,

only install built-in appliances under continuous

worktops, securing them to the adjacent kitchen units or

worktop with screws.

Building-in a dishwasher underneath a ceramic hob is

absolutely forbidden. A dishwasher can be built-in

underneath a conventional hob provided there is no

break in the kitchen worktop, and the dishwasher and

hob are installed and secured correctly, so that no

hazards are generated.

Make sure the dishwasher has been correctly

installed and grounded by a qualified fitter.

This safety requirement must be met. In case of

doubt, call in a qualified fitter. The manufacturer

declines all responsibility for damage to persons or

property resulting from the failure to ground the

appliance or from a defective ground connection.

Before proceeding with installation, disconnect the

main power supply from the work area.

Only for free-standing models

• It is strictly forbidden to mount a cooktop over a

freestanding dishwasher.

• If the appliance is not in a niche and can therefore be

accessed on one side, cover the door hinge area for

safety reasons (cutting hazard). Covers are available

as accessories from specialized retailers or from the

Technical Service Centre.

• To build in the dishwasher, purchase the relative kit

from specialized retailers or from the Technical

Service Centre.

5.1 Leveling

5.1.1 Mounting the feet (only for some models)

Turn the appliance upside-down (see fig. 5-01).

Tighten the nut (see ref. A fig. 5-01) onto the threaded

pin (see ref. B fig. 5-01) of the foot and then fit the

supplied washer; do this on both feet.

Screw the feet onto the appliance until the washers

touch the base; the two feet must be manually adjusted

to the same height to prevent excessive differences in

height between one foot and the other.

Put the appliance back on its feet.

Two people wearing safety gloves are needed to turn the

dishwasher upside-down.

Fig. 5-01

EN

9

5.1.2 Levelling the appliance

Level the appliance using the relative adjustable feet

(e.g.: ref. A fig. 5-02);

use an open-ended wrench to rotate the feet until the

dishwasher is perfectly level.

Some models are fitted with just one rear foot which can

be adjusted with a screw located at the bottom front of

the appliance (ref. A fig. 5-03); use a suitable Phillips

screwdriver to turn the screw until the dishwasher is

perfectly level.

Use a spirit level to check the appliance is perfectly level

(ref. B fig. 5-02).

Leveling is vital for assuring correct dishwasher

operation.

Make sure to leave a gap of at least 3 mm (7/64")

between the top of the dishwasher and the worktop (ref.

C fig. 5-02).

Fig. 5-02

Fig. 5-03

5.2 Connections

Install the dishwasher so as to allow ease of access to

the electrical and hydraulic connections through the

adjacent unit. These connections must never be behind

the dishwasher.

The inlet and drain hoses can be pointed in all

directions. make sure that they are not bent, crushed or

too tight. Tighten the ring nut after pointing the hoses in

the required direction.

Figure 5-04 indicates the distances to maintain between

the dishwasher and the various connections.

Fire hazard!

Do not cover or crush the cord plug.

Fig. 5-04

A through hole with a diameter of at least 8 cm (5/32") is

required to pass the hoses and power cord (ref. A fig. 5-

05). Make sure there area no rough edges that could

damage the power cord or hoses. If the dishwasher is

installed in a metal unit protect the edge of the through

hole for the hoses and power cord with a gasket. Do not

use extension cords when making the electrical

connection as these do not guarantee safety.

Attention!

Installing the dishwasher in a narrow space may bend or

crush the power cord. Take great care in order to reduce

the possibility of damaging the power cord when

installing or removing the appliance.

Fig. 5-05

10

EN

5.2.1 Connecting to the water supply

Preventing the risk of clogging or damage:

If the water pipe is new or has not been used for a long

time, before connecting to the water supply check that

the water is clear and free of impurities, to prevent

damage to the appliance. The dishwasher must always

be connected to the water system with new hoses; old or

used hoses must never be reused.

5.2.1.1 Connecting to the water tap

Connect the inlet hose to a threaded ¾" gas cold water

tap, fitting the supplied filter (ref. A fig. 5-06).

FirFir

Fir

mly securmly secur

mly secur

e the hose by tightening the re the hose by tightening the r

e the hose by tightening the r

elative ring nutelative ring nut

elative ring nut

with your hands (rwith your hands (r

with your hands (r

ef. B fig. 5-06); finish by tighteningef. B fig. 5-06); finish by tightening

ef. B fig. 5-06); finish by tightening

another ¼ turanother ¼ tur

another ¼ tur

n using a pair of plumbing pliers. Forn using a pair of plumbing pliers. For

n using a pair of plumbing pliers. For

models fitted with ACQUASTOP (rmodels fitted with ACQUASTOP (r

models fitted with ACQUASTOP (r

ef. C fig. 5-06) theef. C fig. 5-06) the

ef. C fig. 5-06) the

filter is alrfilter is alr

filter is alr

eady pready pr

eady pr

esent in the thresent in the thr

esent in the thr

eaded ring nut.eaded ring nut.

eaded ring nut.

The dishwasher can be filled with water at a temperature

of less than 60°C (140°F). If the appliance is filled with

hot water, washing times will be reduced by about 20

minutes, but efficiency will be slightly impaired. Make the

connection to the domestic hot water tap using the same

methods described for connecting the appliance to the

cold water tap.

• Recommended temperature: 49°C (120°F), max. 60°C

(140°F).

• Recommended water pressure: 0.5 - 9 bar (7-130

PSI).

If the pressure is too high, fit a pressure reducer.

A rubber hose connected to a sink spray may burst if

installed on the same pipes feeding the dishwasher.

If your sink is fitted with this accessory, remove the

hose and plug the hole.

Fig. 5-06

Do not cut the inlet hose (see fig. 5-07).

If the hose is cut, the dishwasher will not work, water will

leak and you may be injured. If the hose is too long, wind

it up tidily and place it behind the appliance.

The cable harness and electrical components must not

come into contact with the hydraulic system and the

water inlet and drain hoses.

Fig. 5-07

When connecting the dishwasher drain hose to the sink

make sure that the hose is not bent (ref. A fig. 5-08) in order

to prevent cracks or breakages that could damage it.

Fig. 5-08

5.2.1.2 Connecting the drain hose

Connecting to a drain

Insert the relative hose into a drain with a minimum

diameter of 4 cm (1-37/64") (ref. A fig. 5-09); alternatively,

place the hose on the sink (ref. B fig. 5-09) using the

supplied hose support (see fig. 5-10), but taking care to

avoid obstructions or excessive curving. Make sure the

hose cannot fall out. For this purpose, the hose support is

fitted with a hole (ref. A fig. 5-10) which can be used to fix

it to the wall or the tap with a piece of string. The free end

must lie at a height ranging from of 30 to 100 cm (from of

1-7/32" to 3-59/64") (see fig. 5-09) and must never be

immerged in water. If horizontal extension hoses with a

maximum length of 3m are used, position the drain hose

at a maximum height of 85 cm (3-11/32") above the floor.

Fig. 5-09

EN

11

Fig. 5-10

Connecting to a "T" union of the drain circuit

Make the connection upline from the siphon of the drain

line and at least 400 mm (15-3/4") above the floor on

which the dishwasher will be installed.

1. Connect the dishwasher drain hose (ref. A fig. 5-11) to

the "T" union (ref. B fig. 5-11) of the drain circuit using a

38 to 50 mm (1-1/2 to 2") screw clamp* (ref. C fig. 5-11);

if necessary, cut the end of the dishwasher drain hose

(ref. D fig. 5-11) (do not cut the corrugated section).

* Available from any plumbing stockist

Fig. 5-11

Connecting to a waste disposal unit with an air gap

Make the connection upline from the siphon of the drain

line and at least 400 mm (15-3/4") above the floor on

which the dishwasher will be installed.

1. Remove the cover of the waste disposal unit (ref. A

fig. 5-12).

2. Connect the dishwasher drain hose (ref. B fig. 5-12) to

the air gap (ref. C fig. 5-12) using the wide spring

clamp (ref. D fig. 5-12); if necessary, cut the end of the

dishwasher drain hose (ref. E fig. 5-12) (do not cut the

corrugated section). If the drain hose has been cut,

use a 38 to 50 mm (1-1/2 to 2") screw clamp*.

3. To connect the air gap (ref. C fig. 5-12) to the waste

disposal unit inlet (ref. F fig. 5-12), use a rubber union*

(ref. G fig. 5-12) with spring or screw clamps* (ref. H

fig. 5-12).

* Available from any plumbing stockist

Fig. 5-12

Connecting to the air gap (no waste disposal unit)

Make the connection upline from the siphon of the drain

line and at least 400 mm (15-3/4") above the floor on

which the dishwasher will be installed.

1. Connect the dishwasher drain hose (ref. A fig. 5-13) to

the air gap (ref. B fig. 5-13) using the wide spring

clamp (ref. C fig. 5-13); if necessary, cut the end of the

dishwasher drain hose (ref. D fig. 5-13) (do not cut the

corrugated section). If the drain hose has been cut,

use a 38 to 50 mm (1-1/2 to 2") screw clamp*.

2. To connect the air gap (ref. B fig. 5-13) to the "T" union

(ref. E fig. 5-13) of the drain line, use a rubber union*

(ref. F fig. 5-13) with spring or screw clamps* (ref. G

fig. 5-13).

* Available from any plumbing stockist

12

EN

Fig. 5-13

Connecting to a waste disposal unit (no air gap)

Make the connection upline from the siphon of the drain

line and at least 400 mm (15-3/4") above the floor on

which the dishwasher will be installed.

1. Remove the cover of the waste disposal unit (ref. A

fig. 5-14).

2. Connect the dishwasher drain hose (ref. B fig. 5-14) to

the waste disposal unit inlet (ref. C fig. 5-14), using the

wide spring clamp (ref. D fig. 5-14).

* Available from any plumbing stockist

Fig. 5-14

5.2.2 Electrical connections and warnings

Check that the voltage and the frequency of the mains

match the ratings on the name plate of the appliance

positioned on the inner edge of the door.

In the event of damage to the supply cord, have it

replaced by the manufacturer or an authorized technical

service centre.

This appliance must be grounded. in case of a

malfunction of fault, the ground reduces the risk of

electrocution by providing the electrical current with an

alternative, less resistant path. This appliance is fitted

with a supply cord containing a ground wire and plug. fit

the plug into a suitable socket, installed and grounded in

compliance with the laws in force in the country of

installation.

Before making electrical connections, disconnect the

mains power supply from the work area.

Grounding instructions

This appliance is fitted with a cord with ground wire and

plug. Fit the plug into a suitable socket, installed and

grounded in compliance with the laws in force in the

country of installation.

Check that the mains supply in the place of installation

complies with the regulations in force in the country of

use, and that it is correctly grounded.

An incorrectly connected ground wire may generate the

risk of electrocution. If in doubt as to the correct

grounding of the appliance, call in a qualified electrician

or the technical assistance service. Do not change the

plug attached to the appliance. If the plug is not suitable

for the socket, call in a qualified electrician to fit a

suitable plug.

The plug at the end of the power cord and the

corresponding socket must be of the same type and

must conform to current regulations governing electrical

appliances. The plug must be accessible after

installation. Never remove the plug by pulling on the

wire. If the power cord is damaged, have it replaced by

the manufacturer or an authorized service centre.

EN

13

Do not use extension cords, adaptors or shunt

connections in order to avoid the possibility of

overheating or burning, with consequent fire hazard.

In the event of damage to the supply cord, have it

replaced by the manufacturer or an authorized technical

service centre in order to avoid any risk.

5.3 Commissioning

5.3.1 Installation procedure (all models)

Clean the underneath of the worktop lying over the

dishwasher door (see fig.5-15) and apply the steam

guard, as shown in fig. 5-16 (see fig. 5-16 if the adhesive

guard is applied; see fig. 5-17 if the steel guard is

applied). This guard protects the worktop from steam

and condensation when the door of the dishwasher is

opened at the end of the washing cycle.

Fig. 5-15

Fig. 5-16

Fig. 5-17

Push the dishwasher into position, taking care not to twist

or crush the power cord or hoses (see fig. 5-18).

Two people wearing safety gloves are needed to push

the dishwasher into place.

Fig. 5-18

5.3.2 Procedure for mounting the door

panel (models LTE)

Mount the door panel.

Place the template on the inner surface of the panel,

centering it along the upper side and matching up the

reference locators (ref. A fig. 5-19); mark the position of

the door hooks with a pencil (see fig. 5-19). Remove the

template and use a drill with a suitable bit to make holes

at the points marked on the panel.

Fig. 5-19

14

EN

Use the screwdriver to secure the door hooks with the 8

supplied screws (see fig. 5-20) at the marked reference

points.

Fig. 5-20

Drill holes for the panel handle using a drill with a

suitable bit. Use the screwdriver to secure the door

handle before hooking the panel to the dishwasher (see

fig. 5-21).

N.B.: the screws are not supplied.

Fig. 5-21

Attach the door panel: fit the hooks into their slots on the

dishwasher and allow the panel to slide downwards and

slip in to place (see fig. 5-22).

Fig. 5-22

Secure the door to the panel with the supplied screws.

The panel must have a minimum thickness of 20 mm (25/

32") (see fig. 5-23).

Fig. 5-23

Make sure the dishwasher door, complete with panel,

opens comfortably and that the base plate (ref. A fig. 5-

24) does not prevent it from opening fully. If the base plate

prevents the door from opening, mark out the section to

remove (see fig. 5-24), take out the base plate and cut it

along the marking using a compass saw (see fig. 5-25).

Fig. 5-24

Fig. 5-25

5.3.3 Completion of installation (all models)

Finish the cut with a file (see fig. 5-34) in order to remove

any burrs and/or imperfections. Put back the base plate

(see fig. 5-35) and try to open the dishwasher door fully;

if the base plate still obstructs the door, repeat the above

operations.

EN

15

Fig. 5-34

Fig. 5-35

Before securing the dishwasher to the adjacent units,

attach the gaskets to the sides. Remove the adhesive

band on the gasket (see fig. 5-36).

Fig. 5-36

Fix the gasket to the dishwasher, inserting it in the seat

on the sides towards the front (see fig. 5-37), and making

sure that the long side of the gasket, the one with the

hole for inserting the screw, is attached to the outside of

the dishwasher; the hole in the long side must match the

hole in the dishwasher (see ref. A fig. 5-38). Make sure

the gasket adheres perfectly to the dishwasher.

Fig. 5-37

Fig. 5-38

Fig. 5-39 shows the state of the dishwasher after the

above operations are performed.

Fig. 5-39

Tighten the supplied screws with a screwdriver; this

operation definitively fixes the dishwasher to the

adjacent units; cover the side holes using the supplied

plugs (ref. A fig. 5-40).

Fig. 5-40

5.4 Testing

After installation, test the dishwasher by starting a work

cycle. Check for leaks and make sure the appliance

does not malfunction.

16

EN

USER INSTRUCTIONS

4 OPERATING INSTRUCTIONS

Before starting to use the appliance, make sure you have

read and understood all the warnings contained in

chapter 2 "important safety instruction".

Once the dishwasher has been correctly installed,

prepare for use as follows:

• adjust the water softening system;

• add the regenerating salt;

• add the rinse-aid and detergent.

4.1 Using the rinse-aid and detergent

dispensers

The detergent and rinse aid dispensers are situated on

the inner part of the door: the detergent dispenser (ref.

A fig. 4-01) is on the left, and the rinse aid dispenser

(ref. B fig. 4-01) is on the right.

Fig. 4-01

With the exception of the soak program, before every

washing cycle it is necessary to add the required amount

of detergent to the detergent dispenser. The rinse aid, on

the other hand, should only be added as required.

4.1.1 Adding the rinse-aid

The rinse aid helps the dishes dry faster and prevents the

formation of scale deposits and staining; it is automatically

added to the water during the final rinse cycle, from the

container situated on the inner side of the door.

Fig. 4-02

To add rinse aid:

• Open the door.

• Rotate the container cover (ref. A fig. 4-02)

anticlockwise by ¼ of a turn and remove it.

• Add the rinse aid until the container is full

(approximately 140 ml). The optical level indicator (ref.

B fig. 4-02), on the side of the cap should be

completely obscured. Refill the rinse aid when the

optical level indicator becomes clear again, or when

the rinse aid warning light illuminates (see "Description

of controls" manual).

• Replace the cover (ref. A fig. 4-02) by turning it in a

clockwise direction until it is fully closed.

• Use a cloth to remove any spillage of rinse aid which

might lead to the formation of excess foam.

4.1.2 Adjusting the rinse-aid dispenser

setting

The rinse-aid dispenser can be set to one of 6 different

levels. The dishwasher is factory set for medium water

hardness (selector set to "3"). To change the setting, turn

the dispenser selector (ref. c fig. 4-02) to the desired

position: the amount of rinse-aid dispensed is proportional

to the position of this selector.

Make sure that the minimum amount of rinse-aid (selector

turned to "1") is approximately 1 ml and the maximum

amount (selector turned to "6") is approximately 6 ml.

• To adjust the rinse aid setting, rotate the dispenser

cover (ref. A fig. 4-02) through a quarter turn in an

anticlockwise direction and remove it.

• Then use a screwdriver to rotate the rinse aid selector

to the desired position.

EN

17

• Replace the cover (ref. A fig. 4-02) by turning it in a

clockwise direction until it is fully closed.

• The amount of rinse aid must be increased if the

washed dishes appear dull or feature circular stains.

• If, on the other hand, the dishes are sticky or have white

streaks, it is necessary to reduce the rinse aid setting.

4.1.3 Adding the detergent

Do not inhale or swallow detergent as this may cause

burns and/or permanent damage to the nose, mouth and

throat, and even leading to suffocation; keep detergent

away from your eyes. If one of the above situations

occurs, seek medical assistance immediately.

Prevent children from coming into contact with

detergent; keep them away from the dishwasher when

the door is open as it may contain detergent residues.

Fill the dishwasher just before starting the washing cycle

and then keep the detergent out of the reach of children.

To open the detergent dispenser cover, lightly press the

relative button (ref. A fig. 4-03). Add the detergent and

close the cover carefully, pushing down on the arrow (ref.

B fig. 4-03). During the washing cycle, the dispenser will

be opened automatically.

Fig. 4-03

Fig. 4-04

• When a program with hot prewash is selected (see

program table in the "Description of Controls" manual),

extra detergent must be placed in the cavity (ref. A or

B fig. 4-04, depending on models).

• Only use dishwasher-specific detergents. For optimal

washing results it is important to use a good quality

detergent.

• The detergent packs must be sealed and stored in a

dry place to prevent the formation of lumps which may

negatively affect washing results. Once opened the

detergent packs should not be kept for too long,

otherwise the detergent loses its effectiveness.

• Do not use detergents formulated for washing dishes

by hand, because they produce a great deal of foam

and may negatively affect the operation of the

dishwasher.

• Add the correct amount of detergent. An insufficient

amount of detergent will result in a partial removal of

dirt from the dishes, whereas an excessive amount is

wasteful and does not improve the washing results.

• The market offers liquid and powder detergents with

differing chemical compositions, which may contain

phosphates, or be phosphate-free but contain

natural enzymes.

• Detergents containing phosphates are more effective

against grease and starch at temperatures above

60°C (140°F).

• Enzyme detergents, on the other hand, are also

effective at lower temperatures (from 40 to 55°C /

from 104 to 131°F) and are more easily

biodegradable. With enzyme detergents it is possible

to obtain at low temperatures comparable results to

those which can only be achieved at 65°C (149°F)

using traditional detergents. For the safeguarding of

the environment we recommend the use of

phosphate- and chlorine-free detergents.

• When using detergent tabs, place them in the cutlery

basket. The dispenser has been designed for powder or

liquid detergent. As the cover does not open completely

during the washing cycle, tabs are not fully released

(dissolved). This could generate the following problems:

- insufficient detergent released during the cycle and

poor washing results;

- the detergent is compacted in the dispenser and is

released during the final rinse cycle.

The introduction of detergent into the rinse aid dispenser,

even in liquid form, will damage the dishwasher.

4.2 General warnings and

recommendations

Before using the dishwasher for the first time, it is

advisable to read the following recommendations

concerning dish types to be washed and their loading.

18

EN

There are generally no constraints on the washing of

domestic dishes, but in certain cases it is necessary to

take their characteristics into account. Before loading the

dishes into the racks it is necessary to:

• remove coarse food remains: e.g. bones, fish-bones,

etc. which may clog the filter or damage the wash pump;

• soak any pots or pans with burnt-on food remains on

the bottom to facilitate removal, then load them into

the LOWER RACK.

Use the "½ load wash" option (if available) for washing

small amounts of dishes; it saves water and electricity.

When using this function, only load the rack selected

for the ½ load wash; the other rack must remain empty.

There is no need to pre-wash the dishes under running

water before loading them into the racks since this only

wastes water. Correct loading of the dishes helps

ensure optimal washing results.

WARNING!

• make sure that the dishes are securely in place so that

they cannot tip over or obstruct the rotation of the

spray arms during the washing cycle;

• do not place very small objects in the racks as these

could fall and obstruct the spray arms or the wash pump;

• containers such as cups, bowls, glasses and pots

should always be loaded with the opening facing

downwards and with any cavities at an angle, to allow

the water to drain out;

• do not stack dishes or place them in such a way that

they cover one other;

• do not place glasses too close together because they

may knock against each other and break, or there

might be staining at the point where they touch.

MAKE SURE that the items being washed are

dishwasher-safe.

Items which are not dishwasher-safe:

• Wooden dishes, pots or pans: these may be

damaged by the high washing temperatures.

• Handcrafted items: these are rarely suitable for

washing in a dishwasher. The relatively high water

temperatures and the detergents used may damage

them.

• Lightweight objects: place lightweight objects in the

upper rack where the water pressure is lower.

• Dishes and objects in copper, tin, zinc or brass:

these tend to stain.

• Aluminum dishes: items made from anodized

aluminum may lose their color.

• Silverware: silver items may stain.

• Glass and crystal: in general, glass and crystal

objects can be washed in the dishwasher. However,

certain types of glass and crystal may become dull

and lose their clearness after many washings.

Therefore, for these items we recommend using the

least aggressive program available (see "Description

of controls" manual).

• Decorated items: the decorated objects available on

the market are generally able to withstand washing in

the dishwasher, although the colors may fade after a

great many washes. If in doubt as to the fastness of

the colors, it is advisable to wash just a few items at a

time for approximately one month.

4.3 Using the racks

The dishwasher has a capacity of 12 place-settings,

including serving dishes.

Examples of loading 12 place-settings in the upper rack

(see fig. 4-05) and in the lower rack (see fig. 4-06) are

shown below.

Fig. 4-05

Fig. 4-06

4.3.1 Lower rack

The lower rack receives the full force of the lower spray

arm, and should therefore be used for the "toughest" items

with a heavier degree of soiling. All types and combinations

of loads are permitted, provided that the dishes, pots and

pans are arranged with all the soiled surfaces exposed to

the water jets coming from the bottom. To make the most of

the space inside the rack when loading large items, certain

models are equipped with tip-up supports for plates in 2 or

4 sections (see fig. 4-07).

EN

19

With fixed supports With tip-up supports

Fig. 4-07

Loading the lower rack (see fig. 4-8)

Carefully load fl at plates, soup plates, dessert and

serving dishes, positioning them vertically. Pots, pans

and their covers must be loaded upside down.

When loading soup plates and dessert bowls, be sure to

leave a gap between them.

Loading examples:

1/2 load (certain models only)

Fig. 4-8

4.3.2 Cutlery basket (see fig. 4-9/4-10

depending on models)

The cutlery basket can be removed to simplify unloading.

Arrange the cutlery in an orderly manner inside the

basket, with the handles pointing downwards and

taking care not to injure yourself with the knife blades.

The basket is suitable for all types of cutlery, except those

long enough to interfere with the upper spray arm.

Place long items (ladles, wooden spoons and cooking

knives) that may interfere with the spray arm in the upper

rack making sure that knife tips do not protrude.

The dishwasher is complete with two cutlery baskets,

which means that one of them can be removed, freeing

space in the bottom rack, if there is not much cutlery to

be washed, or if a ½ load program is being used (on

models with this function).

The baskets feature an exclusive system of independent

sliding tip-up supports, offering a choice of combinations

to allow optimum use of the space available.

Horizontal Horizontal

insert insert

closed open

Vertical inserts Movement required

to extract the inserts

Fig. 4-9

The cutlery supports and central lid are in the bag of

accessories. The central lid (ref. A fig. 4-10) is intended

to act only as a cover; do not place the cutlery in it.

Fig. 4-10

4.3.3 Upper rack (see fig. 4-11)

It is recommended to load the upper rack with small- or

medium-sized items such as glasses, small plates, tea or

coffee cups, shallow bowls and light objects made from

heat resistant plastic.

If the upper rack is used in the lowermost position, it can

also be loaded with serving dishes, provided they are

only slightly soiled. The top rack is fitted, on the left, with

two plastic racks which can be raised to make room for

tall glasses, such as stem glasses.

Fig. 4-11

20

EN

Loading the upper rack (see fig. 4-12)

Load plates facing forward; cups, bowls etc. must

always be facing downwards. The left-hand side of the

rack can be loaded with two layers of cups and glasses.

The centre can be filled with plates and side-plates,

fitted upright into the supports provided.

Fig. 4-12

Adjusting the upper rack

Version A (see fig. 4-13): the upper rack can be adjusted

in two positions, according to the user's needs and

according to the height of the dishes in the lower rack.

Proceed as follows:

• pull out the right-hand rack guide. Remove the stop

(ref. A fig. 4-13) after releasing the tabs (ref. B fig. 4-13)

(first release the upper tab and then the lower one);

• pull out the left-hand rack guide and remove the

corresponding stop, just as you did for the right-hand

rack guide;

• remove the rack from the guides;

• fit the upper or lower pair of wheels (ref. C fig. 4-13)

into the guides, depending on the setting required;

• return the guide stops to their original positions (ref. d fig.

4-13) (first attach the lower tab and then the upper one).

Fig. 4-13

Version B (see fig. 4-14):

• pull out the rack to its limit position and pull the right

side upwards (ref. A fig. 4-14). At this point it is possible

to load larger sized plates into the lower rack.

• to return to the original position, pull out the upper rack

again and press the release lever (ref. B fig. 4-14).

Fig. 4-14

Version C (see fig. 4-15): the upper rack can be set in

three different positions on both sides. The rack must be

level on both sides.

To raise the rack (ref. A fig. 4-15), lift it with the two

handles (e.g.: ref. B fig. 4-15) to the first or second catch

depending on the height required. To lower it (ref. C fig.

4-15), pull up the two release levers (e.g.: ref. D fig. 4-

15). This is also possible with the rack loaded, but in this

case when lowering the rack it should be held steady

with one hand to avoid knocking the dishes.

Fig. 4-15

5 CLEANING AND USER-MAINTENANCE

Before carrying out any work, always disconnect the

appliance from the electrical power supply.

5.1 General warnings and

recommendations

Never use abrasive and/or corrosive detergents to clean

the appliance.

Page is loading ...

Scholtes LFD S3 XL60HZ Operating Instructions Manual

Scholtes LFD S3 XL60HZ Operating Instructions Manual

in other languages

Related papers

Other documents