Ingersoll-Rand 62131 User manual

Ingersoll-Rand
Brand
Ingersoll-Rand
Model
62131
Type
User manual

This manual is also suitable for

CCN 15231640
SELF EVACUATING OIL DRAIN
OPERATOR’S MANUAL
62131
RELEASED: 10-13-04
REVISED: 5- 24-10
(REV. 05)
INCLUDING: OPERATION, INSTALLATION & MAINTENANCE
READ THIS MANUAL CAREFULLY BEFORE INSTALLING,
OPERATING OR SERVICING THIS EQUIPMENT.
It is the responsibility of the employer to place this information in the hands of the operator. Keep for future reference.
OPERATING AND SAFETY PRECAUTIONS
WARNING
EXCESSIVE AIR PRESSURE. Can cause explosion resulting in
severe injury or death.
S Do not exceed the maximum inlet air pressure as stated on the model plate.
WARNING
EXPLOSION HAZARD. Can cause seriousinjuryorproperty dam-
age.
S Do not use near open flame or heat source.
S This product is not designed for working in explosive environments, including
those caused by fumes and dust, or near flammable materials.
WARNING
HAZARDOUS MATERIALS. Can cause personal injury or proper-
ty damage.
S Do not use for volatile fuel and fluids.
S Obtain Material Safety Data Sheets on all materials from the supplier for proper
handling instructions.
WARNING
HIGH PRESSURE AIR. Bypassing, modifying or removing the
safety / relief valve can cause serious injury or death. Do not bypass, modify or
remove the safety / relief valve. Do not direct air stream at body.
CAUTION
Be certain all operators of this equipment have been trained for
safe working practices, understand it’s limitations and wear safety goggles /
equipment when required.
S Do not use for structural support.
S Disconnect air supply when not in use.
S Use only genuine IR replacement parts to assure longest service life.
GENERAL DESCRIPTION
Model 62131 is a waste oil container which stores up to 20 gallons (75.7 liters) in an ASME
certified steel tank and rapidly discharges using air pressure. The unit is equipped with a
safety relief valve which prevents over-pressurization and a 4-3/4” x 20-1/2” (12.0 cm x
52.0 cm) drain funnel with a filtering screen and a telescoping tube. The tank has (2) rigid
casters and (2) swivel casters for easy maneuvering. It also includes a sight gauge and an
oil shut-off valve.
OPERATION
1. To raise the funnel: Grasp the upper portion of the (5) tube, loosen the (6) thumb screw
and raise the funnel and tube to the desired height. Tighten the (6) thumb screw and
release grasp on tube.
2. To lower the funnel:
Grasp the upper portion of (5) tube, loosen the (6) thumb screw
and lower the funnel and tube to the desired position. Tighten (6) thumb screw and
release grasp on tube.
3. The reservoir includes a sight gauge. Do not overfill the reservoir.
4. To evacuate oil:
Lower the (1) funnel. Always connect the discharge hose before con-
necting air supply. Connect the discharge hose to the (9) oil shut-off valve on the (18)
tank. Be sure the (9) oil shut-off valve is fully engaged. Open the (9) oil shut-off valve.
Before connecting the air supply, be sure that the inlet air line pressure is regu-
lated at no more than 70 p.s.i. (PMAX). Connect the air supply to the (10) air man-
ifold.Neverleave the unit unattendedduring evacuation. Closethe(12)airshut-off
valve immediately when the tank is empty. The discharge hose will begin to shake
when the (18) tank is empty. Disconnect the air supply to the (10) air manifold. Close
the (9) oil shut-offvalve. Slowly open the (12) air shut-off valve to depressurize thesys-
tem. System must be depressurized before returning to service. Disconnect the dis-
charge hose from the (9) oil shut-off valve on the (18) tank. Periodically remove and
clean the (2) funnel screen as necessary.
5. (17) safety relief valve may discharge during evacuation.
DATA
Weight 105 lbs (47.6 kgs)...............................
Recommended Air Operating Pressure 20 - 70 p.s.i.g. (1.38 - 4.83 bar)......
Capacity 20 gallons (75.7 liters).............................
Height (lowered) 52 in. (132.08 cm)...... ................
(fully extended) 73 in. (185.42 cm)...........
Tank Diameter 16 in. (40.64 cm).........................
8
20
Figure 1
3
30
10
29
1
5
32
19
7
31
18
FLOAT VALVE SERVICE PROCEDURES
1. Depressurize system before and during servicing.
2. Wear appropriate safety equipment during servicing.
3. Remove (1) funnel from (5) tube.
4. Remove (6) thumbscrew from (7) c ollar.
5. Unbolt (30) handle and remove from the (18) tank.
6. Loosen the (7) collar and remove the (5) tube from the (18) tank.
7. To loosen the (7) collar, it may require the use of an industrial heat gun to soften the
pipe thread sealant on the (7) collar thread.
a. WARNING -- Do not use an open flame.
b. WARNING -- Be sure the tank vents are open during service.
c. WARNING -- Keep heat away from product labels.
8. Use a large spanner wrench or 12” pipe wrench to remove the (7) collar.
9. Secure tank when removing the collar.
10. Remove the (27) roll pin and the (25) ball from the (26) seat.
11. Remove the (26) seat by unscrewing the seat from the (5) tube.
12. Remove debris and particulatesfrom the (27) roll pin, (25) ball and (26) seat using mild
detergent and water.
a. WARNING -- Do not use solvent, as this may damage the ball.
13. Before reassembly, apply PTFE tape to the (26) seat threads.
14. Assemble in reverse order. Apply Loctite PST or equivalent pipe thread sealant to the
(7) collar threads prior to assembly. Tighten securely.
15. Test all joints for air leakage prior to putting drain back into service.
INGERSOLL RAND COMPANY LTD
209 NORTH MAIN STREET – BRYAN, OHIO 43506
(800) 495-0276 FAX(800) 892-6276
© 2010
www.ingersollrandproducts.com
PN 97999-1130
62131 (en)Page 2 of 2
62131 PARTS LIST
Item Description (size) Qty Part No. Item Description (size) Qty Part No.
1 Funnel (includes item 4) (1) 96546
9 2 Funnel Screen (1) 96547
3 Set Screw (M6x1-6gx5mm) (1)
9 4 Wing Nut (3/8” - 18) (1)
5 Tube (includes items 3, 6, 7 and 25 - 28) (1) 96281
6 Thumbscrew (1)
7 Collar (1)
8 Hose Assembly (3/4 - 14 N.P.T. male) (1) 628094
9 Oil Shut -Off Valve (3/4 - 14 N.P.T.) (1) 10559433
10 Air Manifold Ass’y (includes items 11 - 16) (1) 10559482
11 Air Line Connector (1/4 - 18 P.T.F. male) (1)
12 Air Shut -Off Valve (1)
13 Manifold Block (1)
14 Vent (1)
15 Nipple (1/4 - 18 N.P.T.) (1)
16 Pipe Plug (1/4 - 18 N.P.T.) (1)
17 Safety Relief Valve (80 p.s.i.) (1) 72062185
18 Tank (1) 10559649
19 Rigid Caster (2) 10559466
20 Swivel Caster (2) 10559474
9 21 Cap Screw (5/16” - 18 x 1”) (16)
9 22 Washer (5/16” i.d.) (32)
9 23 Nut (5/16” - 18 NC2B) (16)
9 24 Float Valve Kit (includes items 25 and 27) (1) 67351
9 25 Ball (1” diameter) (1)
9 26 Seat (1)
9 27 Roll Pin (1)
9 28 “O” Ring (1/16” x 1-5/8” o.d.) (1)
9 29 Oil Site Glass (1 - 11-1/2 N.P.T. male) (1) 97330245
30 Handle (1) 10559458
31 Screw (1/4” - 20 x 1/2”) (4) Y6-41-C
32 Warning Label (1) 96261
ACCESSORIES
Transmission Tray 96268
Tool Tray 96269
Oil Drain Accessory Kit 621603-6
9 Items not shown.
6
13 14
Figure 2
11
12
15
17 169
  • Page 1 1
  • Page 2 2

Ingersoll-Rand 62131 User manual

Ingersoll-Rand
Brand
Ingersoll-Rand
Model
62131
Type
User manual
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents