Panasonic EY7880 User manual

Brand: Panasonic

Model: EY7880

Category: Power tools

Type: User manual

Cordless Rotary Hammer

Marteau rotatif [sur batterie]

Martillo rotatorio sin cables

Operating Instructions

Instructions d’utilisation

Manual de instrucciones

Model No: EY7880

IMPORTANT

This manual contains safety information. Read manual completely before first using this product and save this

manual for future use.

IMPORTANT

Ce mode d’emploi contient des informations sur la sécurité. Lisez-le en entier avant d’utiliser le produit et

conservez-le pour référence.

IMPORTANTE

Este manual contiene información de seguridad. Lea completamente este manual antes de utilizar por primera

vez este producto, y guárdelo para poder consultarlo en el futuro.

Index/Index/Indice

English: Page 3 Français: Page 16 Español: Página 29

FUNCTIONAL DESCRIPTION

DESCRIPTION DES FONCTIONS

DESCRIPCIÓN FUNCIONAL

(A) (B) (C)

(D)

(E)

(F)

(G)

(I)

(P)

(T)

(V)

(W)

(A) Chuck Mandrin Portabroca

(B) Depth gauge Jauge de profondeur Calibre de profundidad

ón de marti-

llo/taladro

(D) Speed/Blow Mode selection lever Levier de sélection de vitesse/mode

de soufﬂ erie

Palanca del selector de velocidad/

modo de soplador

(E) Forward/Reverse lever Levier d’inversion marche avant

marche arrière

Palanca de avance/inversión

(F) Variable speed control trigger Gâchette de commande de vitesse Disparador del control de velocided

variable

(G) Battery holder Battery holder Battery holder

(H) Alignment marks Marques d’alignement Marcas de alineación

(I) Battery pack (EY9L80) Batterie autonome (EY9L80) Batería (EY9L80)

(J) Control panel Panneau de commande Panel de controle

(K) LED light on/off button

Bouton Marche/Arrêt de la lumière DEL

Botón ON/OFF de luz LED

(L) Overheat warning lamp (motor/

battery)

Témoin d’avertissement de

surchauffe (moteur/batterie)

Luz de advertencia de

sobrecalentamiento (motor/batería)

(M) Battery low warning lamp Témoin d’avertissement de batterie

basse

Luz de aviso de baja carga de

batería

(N) Battery pack release button Bouton de libération de batterie

autonome

Botón de liberación de batería

(O) Support handle Manche de support Mango de soporte

(P) LED light Lumière DEL Luz indicadora

(Q) Li-ion battery pack dock Poste d’accueil de la batterie

autonome Li-ion

Enchufe de carga de batería Li-ión

(R) Battery charger (EY0L80) Chargeur de batterie (EY0L80) Cargador de batería (EY0L80)

(S) Ni-MH/Ni-Cd battery pack dock Poste d’accueil de la batterie

autonome Ni-MH/Ni-Cd

Enchufe de carga de batería Ni-

MH/Ni-Cd

(T) Pack cover Couvercle de la batterie autonome Cubierta de batería

(U) Shoulder strap Dragonne Correa al hombro

(V) Grease Graisse Grasa

(W) Dust collection cup (EY9X004E)

Collecteur de poussière (EY9X004E)

Fuelle recolector de polvo (EY9X004E)

Ni-MH

Ni-Cd

(R)

(S)

(Q)

(U)

(J)

(O)

(M)

(H)

(N)

(L)

(K)

GENERAL SAFETY

RULES

WARNING! Read all instructions

Failure to follow all instructions listed below

may result in electric shock, fire and/or

serious injury. The term “power tool” in all

of the warnings listed below refers to your

main operated (corded) power tool and

battery operated (cordless) power tool.

SAVE THESE INSTRUCTIONS

Work Area Safety

1) Keep work area clean and well lit.

Cluttered or dark areas invite acci-

dents.

2) Do not operate power tools in ex-

plosive atmospheres, such as in

the presence of flammable liq-

uids, gases or dust.

Power tools create sparks which

may ignite the dust or fumes.

Keep children and bystanders

away while operating a power tool.

Distractions can cause you to lose

control.

Electrical Safety

Power tool plugs must match the

outlet. Never modify the plug in any

way. Do not use any adapter plugs

with earthed (grounded) power tools.

Unmodified plugs and matching out-

lets will reduce risk of electric shock.

Avoid body contact with earthed or

grounded surfaces such as pipes,

radiators, ranges and refrigerators.

There is an increased risk of elec-

tric shock if your body is earthed or

grounded.

3) Do not expose power tools to

rain or wet conditions.

Water entering a power tool will in-

crease the risk of electric shock.

4) Do not abuse the cord. Never use

the cord for carrying, pulling or

unplugging the power tool. Keep

cord away from heat, oil, sharp

edges or moving parts.

Damaged or entangled cords in-

crease the risk of electric shock.

When operating a power tool out-

doors, use an extension cord suit-

able for outdoor use.

Use of a cord suitable for outdoor use

reduces the risk of electric shock.

Personal Safety

1) Stay alert, watch what you are

doing and use common sense

when operating a power tool. Do

not use a power tool while you

are tired or under the influence of

drugs, alcohol or medication.

A moment of inattention while oper-

ating power tools may result in per-

sonal injury.

2) Use safety equipment. Always

wear eye protection.

Safety equipment such as dust

mask, non-skid safety shoes, hard

hat, or hearing protection used for

appropriate conditions will reduce

personal injuries.

3) Avoid accidental starting. Ensure

the switch is in the off position

before plugging in.

Carrying power tools with your fin-

ger on the switch or plugging in the

power tools that have the switch on

invites accidents.

Remove any adjusting key or wrench

before turning the power tool on.

A wrench or a key left attached to a

rotating part of the power tool may

result in personal injury.

5) Do not overreach. Keep proper

footing and balance at all times.

This enables better control of the

power tool in unexpected situations.

6) Dress properly. Do not wear

loose clothing or jewelry. Keep

your hair, clothing and gloves

away from moving parts.

Loose clothes, jewelry or long hair

can be caught in moving parts.

If devices are provided for the

connection of dust extraction and

collection facilities, ensure these

are connected and properly used.

Use of these devices can reduce

dust related hazards.

Power Tool Use and Care

Do not force the power tool. Use

the correct power tool for your

application.

The correct power tool will do the

job better and safer at the rate for

which it was designed.

Do not use the power tool if the

switch does not turn it on and off.

Any power tool that cannot be con-

trolled with the switch is dangerous

and must be repaired.

Disconnect the plug from the pow-

er source and/or the battery pack

from the power tool before making

any adjustments, changing acces-

sories, or storing power tools.

Such preventive safety measures

reduce the risk of starting the pow-

er tool accidentally.

Store idle power tools out of the

reach of children and do not al-

low persons unfamiliar with the

power tool or these instructions

to operate the power tool.

Power tools are dangerous in the

hands of untrained users.

5) Maintain power tools. Check for

misalignment or binding of mov-

ing parts, breakage of parts and

any other condition that may af-

fect the power tools operation. If

damaged, have the power tool re-

paired before use.

Many accidents are caused by

poorly maintained power tools.

Keep cutting tools sharp and clean.

Properly maintained cutting tools with

sharp cutting edges are less likely to

bind and are easier to control.

7) Use the power tool, accessories

and tool bits etc. in accordance

with these instructions and in the

manner intended for the particu-

lar type of power tool, taking into

account the working conditions

and the work to be performed.

Use of the power tool for operations

different from those intended could

result in a hazardous situation.

Battery Tool Use and Care

Ensure the switch is in the off posi-

tion before inserting battery pack.

Inserting battery pack into pow-

er tools that have the switch on in-

vites accidents.

2) Recharge only with the charger

specified by the manufacturer.

A charger that is suitable for one type

of battery pack may create a risk of fire

when used with another battery pack.

3) Use power tools only with specif-

ically designated battery packs.

Use of any other battery packs may

create a risk of injury and fire.

When battery pack is not in use,

keep it away from other metal ob-

jects like paper clips, coins, keys,

nails, screws, or other small metal

objects that can make a connection

from one terminal to another.

Shorting the battery terminals to-

gether may cause burns, or a fire.

5) Under abusive conditions, liq-

uid may be ejected from battery;

avoid contact. If contact acciden-

tally occurs, flush with water. If

liquid contacts eyes, additionally

seek medical help.

Liquid ejected from the battery may

cause irritation or burns.

Service

1) Have your power tool serviced by

a qualified repair person using

only identical replacement parts.

This will ensure that the safety of

power tool is maintained.

. SPECIFIC SAFE-

TY RULES

1) Wear ear protectors. Exposure to

noise can cause hearing loss.

Use auxiliary handles supplied

with the tool. Loss of control can

cause personal injury.

Hold power tools by insulated grip-

ping sur faces when performing an

operation where the cutting tool

may contact hid den wiring.

Contact with a “live” wire will make

ex posed metal parts of the tool

“live” and shock the operator.

Be aware that this tool is always in

an operating condition, since it does

not have to be plugged into an elec-

trical outlet.

5) If the bit becomes jammed, imme-

diately turn the trigger switch off

to prevent an overload which can

damage the battery pack or mo-

tor. Use reverse motion to loosen

jammed bits.

Do not operate the Forward/Reverse

lever when the trigger switch is on.

The battery will discharge rapidly

and damage to the unit may occur.

7) When storing or carrying the tool,

set the Forward/Reverse lever to

the center position (switch lock).

8) Do not strain the tool by holding

the speed control trigger halfway

(speed control mode) so that the

motor stops. The protection cir-

cuit will activate and may prevent

speed control operation. If this hap-

pens, release the speed control

trigger and squeeze again for nor-

mal operation.

9) Be careful not to get dust inside the

chuck.

10) Do not touch the rotating parts to

avoid injury.

11)

Do not use the tool continuously for a

long period of time. Stop using the tool

from time to time to avoid temperature

rise and heat overload of the motor.

12) Do not drop the tool.

13)

Do not put the tool on the place where

the chuck cover is depressed. The bit

may come off from the chuck cover

and fall down when the chuck cover is

depressed. It may cause injuries.

Symbol meaning

V Volts

Direct current

No load speed

… min

-1

Revolutions or

reciprocation per minutes

Forward rotation

Reverse rotation

Rotation with hammering

Rotation only

WARNING:

Some dust created by power sand-

ing, sawing, grinding, drilling, and

other construction activities contains

chemicals known to the State of Cal-

ifornia to cause cancer, birth defects

or other reproductive harm. Some

examples of these chemicals are:

* Lead from lead-based paints

* Crystalline silica from bricks and

cement and other masonry prod-

ucts

* Arsenic and chromium from chem-

ically-treated lumber.

To reduce your exposure to these

chemicals: work in a well ventilated

area, and work with approved safety

equipment, such as dust masks that

are specially designed to filter the

microscopic particles.

. FOR BATTERY

CHARGER & BAT-

TERY PACK

Important Safety Instructions

SAVE THESE IN STRUCTIONS -This

manual contains important safety

and operating instructions for bat-

tery charger EY0L80.

2) Before using battery charger, read

all instructions and cautionary mark-

ings on (1) battery charger, (2) bat-

tery pack.

3) CAUTION

- - To reduce the risk of in-

jury, charge only Panasonic Battery

Pack as shown in last page.

Other types of batteries may burst

causing personal injury and dam-

age.

4) Do not expose charger to rain or

snow.

5) To reduce the risk of damaging the

electric plug and cord, pull by plug

rather than cord when disconnect-

ing charger.

6) Make sure cord is located so that it

will not be stepped on, tripped over,

or otherwise subjected to damage

or stress.

7) An extension cord should not be

used unless absolutely necessary.

Use of improper extension cord

could result in a risk of fire and

electric shock. If extension cord

must be used, make sure:

a. that pins on plug of extension

cord are the same number, size

and shape as those of plug on

charger.

b. that extension cord is proper-

ly wired and in good electrical

condition.

c. that wire size is large enough

for ampere rating of charger as

specified below.

RECOMMENDED MINIMUM AWG SIZE OF

EXTENSION CORDS FOR

BATTERY CHARGERS

AC Input Rating.

Amperes

AWG Size of Cord

Equal to or

greater than

But less

than

Length of Cord, Feet

25 50 100 150

0 2 18 18 18 16

8) Do not operate charger with dam-

aged cord or plug

replace them

immediately.

9) Do not operate charger if it has re-

ceived a sharp blow, been dropped,

or otherwise damaged in any way;

take it to a qualified serviceman.

10) Do not disassemble charger; take

it to a qualified serviceman when

service or repair is required. Incor-

rect reassembly may result in a risk

of electric shock or fire.

11) To reduce the risk of electric shock,

unplug charger from outlet before

attempting any maintenance or

cleaning.

12) The charger and battery pack are

specifically designed to work togeth-

er. Do not attempt to charge any

other cordless tool or battery pack

with this charger.

13) Do not attempt to charge the battery

pack with any other charger.

14) Do not attempt to disassemble the

battery pack housing.

15) Do not store the tool and battery

pack in locations where the tempera-

ture may reach or exceed 50°C (122°F)

(such a metal tool shed, or a car in

the summer), which can lead to de-

terioration of the storage battery.

16) Do not charge battery pack when the

temperature is BELOW 0°C (32°F)

or ABOVE 40°C (104°F). This is very

important.

17) Do not incinerate the battery pack.

It can explode in a fire.

18) Avoid dangerous environment. Do not

use charger in damp or wet locations.

19) The charger is designed to operate

on standard household electrical

power only. Do not attempt to use it

on any other voltage!

20) Do not abuse cord. Never car-

ry charger by cord or yank it to dis-

connect from outlet. Keep cord away

from heat, oil and sharp edges.

21) Charge the battery pack in a well

ventilated place, do not cover the

charger and battery pack with a

cloth, etc., while charging.

22) Use of an attachment not recom-

mended may result in a risk of fire,

electric shock, or injury to persons.

23) Do not short the battery pack. A bat-

tery short can cause a large current

flow, over heating and burns.

24) NOTE: If the supply cord of this appli-

ance is damaged, it must only be re-

placed by a repair shop appointed by

the manufacturer, because special

purpose tools are required.

25) TO REDUCE THE RISK OF ELEC-

TRIC SHOCK, THIS APPLIANCE

HAS A POLARIZED PLUG (ONE

BLADE IS WIDER THAN THE

OTHER).

This plug will fit in a polarized outlet

only one way. If the plug does not fit

fully in the outlet, reverse the plug. If

it still does not fit, contact a qualified

electrician to install the proper outlet.

Do not change the plug in any way.

. ASSEMBLY

Attaching or Removing Bit

Chuck

NOTE: Grease for bit

Grease the oval indentation

on the bit with the supplied

grease at least once a month.

1. To mount the bit

1-1. Insert a bit into the mounting hole,

and turn it slightly to locate an en-

gaged position.

1-2. At the engaged position, push the

bit as far as it goes. Make sure that

the bit is fixed by pulling it.

SDS PLUS type

shank

2. To dismount the bit

2-1. Depress the chuck cover and pull

the bit.

Attaching or Removing Bat-

tery pack

Battery holder

The battery pack is designed to be in-

stalled by proceeding two steps for safety.

Make sure the battery pack is installed

properly to the main body before use.

Battery pack Installation and Removal

-For removal-

Push the battery holder ( ).

While the battery pack release button

is held up, (

) move the battery pack

laterally and pull out the pack. (

)

Battery

holder

Release

lever

-For installation-

To attach the battery pack, line up the

alignment marks on the body of the

tool and the battery pack, (

) and

insert the battery pack. (

)

• After you hear the battery pack

clicks when inserting it, keep in-

serting it firmly until the lever locks

it to click once more.

NOTE:

The overheat warning lamp and

the battery low warning lamp will

flash when the battery pack is not

inserted firmly.

. OPERATION

[Main Body]

Forward/Reverse lever

ReverseForward

Be sure to set the switch in the cent-

er to lock it after use.

Operate the Forward/Reverse lever

after the motor rotation is completely

stopped.

Hammering/drilling switching

lever/Speed/Blow Mode selec-

tion lever

1. There are four modes available with

the combination of Hammering/ drill-

ing switching lever and Speed/Blow

Mode selection lever.

Select the suitable mode for appli-

cation.

2. Operate the mode change af-

ter the motor rotation is completely

stopped.

Position of

switching

lever

Speed/Blow Mode

selection lever

Recommended

application

(

Rotation with

hammering

)

Hard blow hammer-

ing mode

This mode has hard

blow hammering which

is suitable for concrete

drilling.

Concrete drill

Soft blow hammering

mode

This mode is suitable

for concrete drilling

with smaller diameter

drill, or for drilling into

soft base material.

Small diameter

concrete drill

(

Rotation only

)

High speed drilling mode

This mode is suitable

for metal drilling with

high speed rotation.

Metal drill

Metal hole saw

Slow speed drilling mode

This mode is suitable

for wood drill with high

torque.

Wood drill

Variable speed control trigger

To set the center of a hole, pull the trig-

ger slightly to start the drill rotation

slowly.

Support handle

Place the support handle at your favorite

position and tighten the handle securely.

Loosen Tighten

Depth gauge

Loosen the support handle and adjust

the depth gauge at your favorite depth.

After adjusting, tighten the support

handle and fix depth gauge.

Depth gauge

Depth of drilling

Installing the Shoulder Strap

CAUTION:

• Install the shoulder strap firmly to

the main unit of the tool and check

the length of the strap before use.

• Check the condition of the strap

and do not use if it is cut or torn etc.

There is a risk of injury or damage

if used while improperly installed.

• Please wear the shoulder strap se-

curely on the shoulder.

There is a risk of injury or damage

if it is accidentally dropped.

1. Pass the strap through the strap

holders.

2. Pass the strap through the buckles

and adjust the length.

Shoulder pad

Follow the instructions below in order

to avoid injury.

• The shoulder strap can be adjusted

according to the individual.

• Adjust the shoulder pad to the

shoulder.

• Pull the shoulder strap to make

sure it is firmly attached to the main

unit of the tool.

Control panel

(1) Battery low warning lamp

Off (normal

operation)

Flashing (No charge)

Battery protection

feature active

Excessive (complete) discharging of

Li-ion batteries shortens their service

life dramatically. The rotary hammer

includes a battery protection feature

designed to prevent excessive

discharging of the battery pack.

• The battery protection feature ac-

tivates immediately before the bat-

tery loses its charge, causing the

battery low warning lamp to flash.

• If you notice the battery low warn-

ing lamp flashing, charge the bat-

tery pack immediately.

(2) Overheat warning lamp

Off (normal

operation)

Flashing: Overheat

Indicates operation has

been halted due to motor

or battery overheating.

The overheating protection feature

halts driver operation to protect the

motor and battery pack in the event

of overheating. The overheat warning

lamp on the control panel flashes

when this feature is active.

•

If the overheating protection feature

activates, allow the driver to cool

thoroughly (at least 30 minutes).

The driver is ready for use when the

overheat warning lamp goes out.

• Avoid using the driver in a way that

causes the overheating protection

feature to activate repeatedly.

NOTE:

• In summer or in other situations

where the temperature is high, the

overheating protection feature may

activate and prevent continual use.

(3) LED light

Pressing the but-

ton tog gles the LED

light on and off.

The light illuminates

with very low cur-

rent, and it does not

adversely affect the

performance of the driver during use

or its battery capacity.

CAUTION:

•

The built-in LED light is designed to illu-

minate the small work area temporarily.

•

Do not use it as a substitute for a

regular

flashlight, since it does not

have enough brightness

This product has the built-in LED light.

This product is classified into “Class 1

LED Product” to IEC (EN) 60825-1 : 2001

Class 1 LED Product

Caution : DO NOT STARE INTO BEAM.

Use of controls or adjustments or performance

of procedures other than those speciﬁ ed herein

may result in hazardous radiation exposure.

Battery pack

For Appropriate Use of Bat tery Pack

Li-ion Battery Pack (EY9L80)

• For optimum battery life, store the

Li-ion battery pack following use

without charging it.

• When battery pack is not in use, keep it

away from other metal objects like: paper

clips, coins, keys, nails, screws, or other

small metal objects that can make a con-

nection from one terminal to another.

Shorting the battery terminals togeth-

er may cause sparks, burns or a fire.

(1)

(2)

(3)

• When operating the battery pack, make

sure the work place is well ventilated.

• When the battery pack is removed

from the main body of the tool, re-

place the battery pack cover imme-

diately in order to prevent dust or dirt

from contaminating the battery termi-

nals and causing a short circuit.

Battery Pack Life

The rechargeable batteries have a lim-

ited life. If the operation time becomes

extremely short after recharging, re-

place the battery pack with a new one.

Battery Recycling

ATTENTION:

FOR Li-ion Battery Pack, EY9L80

A Li-ion battery that is recyclable

powers the product you have pur-

chased. Please call 1-800-8-BAT-

TERY for information on how to re-

cycle this battery.

Battery charger

Charging

Cautions for the Li-ion Battery

Pack

•

Make sure the terminals of the bat-

tery charger are not contaminated

with liquid, grease or other substanc-

es before charging the battery pack.

If you notice the terminals of the bat-

tery charger contaminated, be sure

to wipe or take them off before use.

The life of the battery pack may ad-

versely be affected when the ter-

minals are clogged with the dust or

dirt which becomes solid with liquid

or grease.

•

If the temperature of the battery

pack falls approximately below -10°C

(14°F), charging will automatically

stop to prevent degradation of battery.

Common Cautions for the Li-

ion/Ni-MH/Ni-Cd Battery Pack

• The ambient temperature range is be-

tween 0°C (32°F) and 40°C (104°F).

If the battery pack is used when the bat-

tery temperature is below 0°C (32°F),

the tool may fail to function properly.

• When charging a cool battery

pack (below 0°C (32°F)) in a warm

place, leave the battery pack at the

place and wait for more than one

hour to warm up the battery to the

level of the ambient temperature.

• Cool down the charger when charg-

ing more than two battery packs con-

secutively.

• Do not insert your fingers into con-

tact hole, when holding charger or

any other occasions.

CAUTION:

To prevent the risk of fire or dam-

age to the battery charger.

• Do not use power source from an

engine generator.

• Do not cover vent holes on the

charger and the battery pack.

•

Unplug the charger when not in use.

Li-ion Battery Pack

NOTE:

Your battery pack is not fully charged

at the time of purchase. Be sure to

charge the battery before use.

Battery charger (EY0L80)

1. Plug the charger into the AC outlet.

NOTE:

Sparks may be produced when the

plug is inserted into the AC power

supply, but this is not a problem in

terms of safety.

2. Insert the battery pack firmly into

the charger.

Line up the alignment marks and

place the battery onto the dock on

the charger.

2 Slide forward in the direction of

the arrow.

Alignment marks

3. During charging, the charging lamp

will be lit.

When charging is completed, an inter-

nal electronic switch will automatically

be triggered to prevent overcharging.

• Charging will not start if the battery

pack is warm (for example, immedi-

ately after heavy-duty operation).

The orange standby lamp will be

flashing until the battery cools down.

Charging will then begin a

utomatically.

4. The charge lamp (green) will

flash slowly once the battery is

approximately 80% charged.

5. When charging is completed, the

charging lamp will start flashing

quickly in green color.

If the temperature of the battery pack

is 0°C (32°F) or less, charging takes

longer to fully charge the battery pack

than the standard charging time.

Even when the battery is fully charged,

it will have approximately 50% of the

power of a fully charged battery at

normal operating temperature.

If the power lamp does not light

immediately after the charger is

plugged in, or if after the standard

charging time the charging lamp

does not flash quickly in green, con-

sult an authorized service center.

If a fully charged battery pack is insert-

ed into the charger again, the charging

lamp lights up. After several minutes,

the charging lamp may flash quickly to

indicate the charging is completed.

Remove the battery pack while the

battery pack release button is held up.

Ni-MH/Ni-Cd Battery Pack

NOTE:

When you charge the battery pack for

the first time, or after prolonged stor-

age, charge it for about 24 hours to

bring the battery up to full capacity.

Battery charger (EY0L80)

1. Plug the charger into the AC outlet.

NOTE:

Sparks may be produced when the

plug is inserted into the AC power

supply, but this is not a problem in

terms of safety.

Insert the battery pack firmly into the

charger.

3. During charging, the charging lamp

will be lit. When charging is com-

pleted, an internal electronic switch

will automatically be triggered to

prevent overcharging.

• Charging will not start if the battery

pack is warm (for example, immedi-

ately after heavy-duty operation).

The orange standby lamp will be

flashing until the battery cools down.

Charging will then begin automatically.

4. When charging is completed, the

charging lamp will start flashing

quickly in green color.

5. If the charging lamp does not light

immediately after the charger is

plugged in, or if after the standard

charging time the charging lamp

does not flash quickly in green, con-

sult an authorized service center.

6. If a fully charged battery pack is in-

serted into the charger again, the

charging lamp lights up. After sever-

al minutes, the charging lamp may

flash quickly to indicate the charg-

ing is completed.

Battery pack

release button

LAMP INDICATIONS

Green Lit

Charger is plugged into the AC outlet.

Ready to charge.

Green Flashing Quickly

Charging is completed. (Full charge.)

Green Flashing

Battery is approximately 80% charged (Usable charge. Li-ion

only).

Green Lit

Now charging

Orange Lit

Battery pack is cool.

The battery pack is being charged slowly to reduce the load on

the battery. (Li-ion only)

Orange Flashing

Battery pack is warm. Charging will begin when temperature

of battery pack drops.

If the temperature of the battery pack is -10°C (14°F) or less,

the charging status lamp (orange) will also start ﬂ ashing.

Charging will begin when the temperature of the battery pack

goes up (Li-ion only).

Charging Status Lamp

Left: green Right: orange will be displayed.

Both Orange and Green Flashing Quickly

Charging is not possible. Clogged with dust or malfunction of

the battery pack.

Dust Collection Cup (EY9X004E)

* Drill bits of which diameter is 20 mm

above cannot be inserted through

dust collection cup.

* Do not use the tool for cutting other

than concrete, mortar and other ceram-

ic materials. If used for cutting metal

materials, the dust collection cup may

be damaged by the metal chip heat.

1. Install a dril bit.

2. Pass the drill bit through A and fix

the cup at B by matching with the

shape of the support handle.

Operation

Keep the dust collection cup in close

contact with the wall surface during

operation.

Removal

Hold the base of the dust collection

cup for removal.

Base

Please remove after thoroughly get-

ting rid of the dust in the dust collec-

tion cup.

Storage

Do not store the dust collection cup

in a compressed position. If kept in

a compressed position, it may be

impossible to return to the original

shape.

. MAINTENANCE

Use only a dry, soft cloth for wiping

the unit. Do not use a damp cloth,

thinner, benzine, or other volatile sol-

vents for cleaning.

. ACCESSORIES

CAUTION:

To prevent the risk of injury, only use

accessory or attachment for its stat-

ed purpose.

Dust Collection Cup

•EY9X004E

Drill chuck

•EY9HX400E

Hammer chuck

•EY9HX401E

Chisel Attachment

•EY9HX402E

If you need any assistance for more

details regarding these accessories,

ask your local service center.

. USAGE SUGGESTION

1. If there isn’t enough force pushing down on the bit, the hammer may not be able

to blow in hammering mode.

This is to prevent the hammering mode from operating with no load. Press down

harder on the bit to engage the hammer and cause it to blow.

Always be sure to press down with enough force when working.

2. In winter or in other situations where the temperature of the unit is low (5°C (41°F)

or below), the blow of the hammering mode may be weaker than normal at the be-

ginning stage.

This is because the grease becomes stiffer in low temperatures, increasing fric-

tion.

If this should happen, operating hammering mode with no load for approximately

30 seconds and repeat this 3 times. This will restore its blowing power.

. SPECIFICATIONS

MAIN UNIT

Maximum Drilling Diameter

Concrete 20 mm (25/32")

Steel 13 mm (33/64")

Wood 27 mm (1-1/16")

Motor Voltage 28.8 V DC

Speed At No Load (RPM)

Slow Mode 0

–

500 min

-1

(rpm)

High Mode 0

–

920 min

-1

(rpm)

Blows Rate Per Minute (BPM)

Soft Mode 0

–

2800 min

-1

(bpm)

Hard Mode 0

–

4500 min

-1

(bpm)

Weight (with battery pack)

3.8 kg

(8.4 lbs)

Overall length 319 mm (12

9/16")

BATTERY PACK

Model EY9L80

Storage battery Li-ion Battery

Battery voltage 28.8 V DC (3.6 V x 8 cells)

Capacity 3 Ah

BATTERY CHARGER

Model EY0L80

Rating See the rating plate on the bottom of the charger.

Weight

0.95 kg

(2.1 lbs)

[Li-ion battery pack]

Charging time 3 Ah

14.4 V 28.8 V

EY9L40

Usable: 35 min.

Full: 50 min.

EY9L80

Usable: 55 min.

Full: 70 min.

[Ni-Cd/Ni-MH battery pack]

Charging time

7.2 V 9.6 V 12 V 15.6 V 18 V 24 V

1.2 Ah

EY9065

EY9066

EY9080

EY9086

EY9001

20 min.

1.7 Ah

EY9180

EY9182

EY9101

EY9103

25 min.

2 Ah

EY9168

EY9188

EY9106

EY9107

EY9108

EY9136

EY9116

EY9117

30 min.

60 min.

3 Ah

EY9200 EY9230 EY9210

45 min. 90 min.

3.5 Ah

EY9201 EY9231 EY9251

55 min. 65 min.

NOTE: This chart may include models that are not available in your area.

Please refer to the latest general catalogue.

Page is loading ...

PANASONIC CONSUMER ELECTRONICS COMPANY

One Panasonic Way, Secaucus, New Jersey 07094

EN. FR. ES

EY981078801 H1907 Printed in China

Panasonic EY7880 User manual

Brand: Panasonic

Model: EY7880

Category: Power tools

Type: User manual

Download PDF

report

in other languages

français: Panasonic EY7880 Manuel utilisateur
español: Panasonic EY7880 Manual de usuario

Panasonic EY7880 User manual

Panasonic EY7880 User manual

in other languages

Related papers

Other documents