Page is loading ...
Stereo Clock Radio for iPhone and iPods
Please read this user’s guide before using your new docking speaker
Operating Instructions
CRX300iP
CONTROLS AND INDICATIONS
TIME
ALARM
Time settings
SLEEP
Set sleep timer
and show status
PRESET
Select a preset
radio station
Adjust the time, Alarm 1, Alarm 2
and Sleep time.
Program the radio atations
Skips Tracks in iPhone/iPod
Touch mode
To enter selections,
Set Alarm 1, Alarm 2
settings.
Plays songs on the
iPhone/iPod Touch list.
Set the alarm timer
Turn ON/OFF the
alarm tone
Plug the AC adapter to CRX300iP unit
4.Prepare the Docking
PUSH OPEN the docking tray and pull it all the way out, dock the iPhone/iPod into the cradle with the correct insert.
3.Extend the FM Wire
Extend the FM antenna as much as you can to
improve reception sensitivity
Unlock the battery holder at the bottom of the unit,
and insert the cell battery CR2032 (Not included)
1.Connect the Power Source 2.Install the Backup Battery
5. Install the App
To begin setup, dock your iPhone/iPod Touch to the CRX300iP.
A dialogue box will appear, notifying that the TEAC iDock application is
absent. Follow the on-screen instructions to install the application.
Once installed, you can start using the CRX300iP.
NOTE: Please ensure you are connected to the WIFI system when downloading
the application and receiving weather updates.
Help
Alarm
setting
Time
Weather
Setting
Radio
After the TEAC iDock Application settings are
completed, the current Time/Weather/Alarm will
be synced to the CRX300iP.
Unit is ready for operation.
7.Sync App to the Unit
6. Preset Time/Alarm/Weather/FM Radio in the App
NOTE: When inserting an iPhone/iPod Touch into the
CRX30iP, make sure the correct adapter is used. The
adapter should have been supplied with the Apple
product. If otherwise, the adapter can be purchased from
Apple stores or Apple web-site.
insert16
insert15
Use this insert For this iPhone/iPod
iPod touch 2G
iPhone 3G/3GS
nano 4Ginsert17
QUICK START
DISPLAY/MEMORY
Display preset, Alarm 1
and Alarm 2 settings in
lower display
Memorize preset
stations in FM
radio mode.
Tips: Please ensure you are connected to the network at all times when using the application to obtain the latest
Time and Weather updates.
Note: It is advised to leave the TEAC iDock Application active while docked in the CRX300iP docking tray.
When the application is off, the unit will cease weather and time updates.
Set up your personal settings in the App. For details, please follow the SETUP instructions in
App by pressing HELP
FM
AUX
AM/PM
Indicator
Alarm Status
Indicator
iPhone/
FM/AUX
Input Indicator
High/Low
Temperature*
Indicator
Alarm Setting/
Current
Temperature*
/Date/Sleep
Wake To
Status Indicator
Sleep Status
Indicator
Time/Volume/
FM Step/Scan/
FM Preset/Memory
Indicator
FM Stereo
mode Indicator
FM MHZ
Indicator
NOTES:
*
Applicable when docking the iPhone/iPod Touch
with the App
Weather
Indicator*
12:35
Weather
Tue, 02 Feb 2010
Guangzhou
Mostly Cloudy
73%
17/23 C
5
Wind:
High/Low Temperatre:
UV Index:
Humidity:
From SSE at 17.7km/h
23 C
17/23C
Tue The Fri SatWed
16/28C 15/17C 15/18C 16/21C
Help
Time Weather Radio Setting
12:35
Weather
Tue, 02 Feb 2010
Guangzhou
Mostly Cloudy
73%
17/23 C
5
Wind:
High/Low Temperatre:
UV Index:
Humidity:
From SSE at 17.7km/h
23 C
17/23C
Tue The Fri SatWed
16/28C 15/17C 15/18C 16/21C
Help
Time Weather Radio Setting
ENTER,
SET+/- PLAY/PAUSE
INPUT VOL+/- POWER, ALARM
RESET
Turn on the unit or
switch to standby mode.
Stop Alarm and reset
alarm for the next day.
Set input selection Adjust volume
Set clock
setting in 12/24hr
Audio source input Connect AC
adapter
DC IN 5V
SNOOZE/DIMMER
Snooze alarm mode
Dim display
12/24HR AUDIO IN
Setting the Clock, Date, Weather by App
Setting the Alarm by App
Setting the Alarm manually
1. Initiate the TEAC iDock App in the iPhone/iPod Touch.
2. Using the TEAC iDock App, select Alarm Settings to make changes to the alarm 1 and alarm 2 time settings.
3.The TEAC iDock App allows you to select a personalized alarm tune/song from the iPhone/iPod Touch playlist.
If no tune/song is selected in the alarm settings, the App will randomly select a song from the playlist available.
4. Once set, dock the iPhone into the unit with the App on.
5. Alarm settings on the iPhone/iTouch is automatically transferred and synchronized into the unit.
WARNING: Alarm settings on the iPhone/iTouch TEAC iDock App will overwrite both alarm settings previously set on the clock radio
unit when the iPhone/iPod Touch is docked.
1. Press and Hold ALARM, Alarm 1 "hour" setting will start flashing.
2. Press SET +/- to adjust and "hour"
alarm settings.
3. Press ENTER to confirm the "hour" setting, "minute" settings will start to flash.
4.
Press SET
+/-
to adjust the minute settings, then, ENTER to set the minute settings. The wake-to source
"BUZ/IP/FM" will start to flash.
5.
Adjust the personal source of alarm tunes from the selections available (Buzzer/iPod/FM). The selections
can be made by pressing Set
+/-
. Press ENTER to confirm setting.
6.
When Alarm 1 is set, press ALARM again to set Alarm 2. Or press ALARM twice to enterthe Alarm 2 settings.
7. Repeat the step 2-5 to set Alarm 2
Using the Audio-in jack
You can play any portable MP3 player or portable audio device through the CRX300ip via the AUDIO IN jack.
1. Connect the AUDIO-IN jack from the back panel of the unit to the output from your device.
2. Press INPUT to select "AUX" mode. Display will show "AUX".
3. Play the music from the external audio device.
4. Adjust the volume by pressing the VOLUME +/- buttons.
Using the Sleep mode
1. When the iPhone/iPod Touch is docked into the unit with the TEAC iDock App activated, the weather information
would appear in the lower Display.
2. Press DISPLAY/MEMORY to view the preset Date, Alarm 1, Alarm 2 respectively. Press again to revert back to
the weather display.
3. When the App is not in use, the preset DATE will appear in the lower display by default. Press DISPLAY/MEMORY
to view Alarm 1, amd Alarm 2 respectively. Press again to revert back to the DATE display.
Note:
1. Ensure that the alarm indicator is on and is in the right mode when setting the alarm. If not, the alarm may not sound.
2. When the iPhone/iTouch is docked with the App activated, the Alarm Settings in the App will be synchronized to the unit and overwrite the
settings in the unit.
3. When the unit is on, the default wake-to source is set to BUZZER. Other wake-to sources will be activated in standby mode. When the iDock
App is activated and the unit is on standby mode, the App's designated song will play as the alarm wake-to source.
Tuning by App
1. Dock the iPhone/iPod Touch into the dock, and launch the TEAC iDock App on your iPhone/iPod Touch.
2. Choose the FM ticker in the App, and an FM input will appear on the unit display.
3. Press AUTO to scan the FM stations automatically, auto scanned stations will be stored as a preset station.
20 stations can be stored.
4. Or, alternatively, turn on the Station Scroll to select your desired station manually. Press SAVE to store the FM
station in your desired memory location.
5. Press preset stations by M1-M20 to select a relevant station.
Tips: Other than auto scanning in App, you may also fine tune the FM steps manually through the unit or App. Both the unit and App display
will show the tuning status at the same time.
The Sleep Mode function permits the user to set a selected time for the unit to shut off. This setting would gradually
lower the volume while the radio or iPhone/iPod Touch is in play.
1. Press and hold SLEEP to set the sleep timer. Press SET+/- to adjust the sleep time. Press ENTER to confirm the setting
2. When Sleep time is set, "ZZZ" appears in the display.
3. Press SLEEP to view the preset sleep time in the lower display.
4. To stop listening at any time, press the POWER to turn unit off.
Setting the clock and date manually
1. When alarm is on, press SNOOZE/DIMMER to turn the alarm off. The alarm will resound in 10 minutes.
2. When alarm is on, press STANDBY/ALARM RESET to reset the alarm for the next day.
3. Press ALARM to turn on/off the alarm setting. Alarm icon should indicate if the alarm is on alert mode or standby mode.
1. Before docking the iPhone/iPod, please choose the correct dock insert to match. Wrong dock inserts would
affect playback and charging.
2. PUSH OPEN the docking tray and pull it all the way out, dock the iPhone/iPod into the unit with the correct insert.
3. When the iPhone/iPod is docked, the iPhone/iPod input source will be set as priority source. The iPhone/iPod icon
appears in the display.
4. If iPhone/iPod is in standby mode, press POWER to turn on the iPhone/iPod
5. Choose the songs from the iPhone/iPod to play; or press PLAY/PAUSE to play the music.
6. Adjust the volume by pressing VOLUME +/- on top of the unit.
7. Press >> or << in the front panel to skip tracks.
Using the Alarm
Listening to iPhone/iPod
Listening to Radio
1. A prompt will appear during the first three times the TEAC iDock App is used with the following request, " 'TEAC'
Would like to Use your Current Location" .
2. Press OK to retrieve your current location time, date, and weather updates.
3. Press weather ticker in the App to download your current location weather conditions.
4. Once set, dock the iPhone/iPod Touch into the unit with the App on.
5. Current time, date and weather are synchronized and displayed into the unit automatically.
Tips: Go to the setting page in the App to select 12/24 hour mode, and turn on/off of the time flash colon.
Manual Tuning
1. Press INPUT to select the FM input mode, "FM" appears on the unit display.
2. Press and hold SET +/- to scan the available FM stations.
3. Once station is selected, press and hold DISPLAY/ MEMORY until P01 appears in the display.
4. Press SET +/- again to select the preset number, then press DISPLAY/MEMORY to store.
5. To listen to the pre-saved radio stations, press PRESET to select a preset station.
Note: To increase the sensitivity of the reception and to reduce static, fully extend the FM wire.
Note: The FM frequency display is raised or lowered by a step of 0.1MHz. For example, frequency between 88.00 to 88.05MHz will be
displayed as "88.0MHz".
Note: When the iPhone/iTouch is docked with the TEAC iDock App activated, the preset FM station in the App will NOT override the preset
stations in the unit.
1. Press 12/24hr at the rear of the unit to choose 12/24 hr setting.
2. When 12 hr setting is chosen, AM/PM appears in the display along with the time.
3. Press TIME , the "hour" starts to flash in the display.
4. Press SET +/ - to adjust the "hour".
5. Press ENTER to confirm the "hour" setting, afterwhich, the "minute" setting starts to flash.
6. Press SET +/- repeatedly, then press ENTER to make changes to the minute settings.
7. Press and hold TIME, the "yyyy" starts to flash in the display. Press SET+/- to set the year and ENTER to exit.
8. Set the "mm", "dd" like Step7 to set the month and day respectively. Press ENTER to exit.
Note: When iPhone is docked with App activated, the time and date settings in App will override the original settings in the unit.
Using the DIMMER
During normal operation, press the SNOOZE/DIMMER to control the brightness of the LCD display.
Warning
Problem Solving
Check all cables to ensure they are connected correctly
Check if the batteries are fully charged and are in place correctly
Check if the iPhone / iPod touch is inserted correctly; undock the player, check fo any obstruction
on the connectors and dock again.
If a fault occurs, please check the points listed below:
Never open the digital unit casing under any circumstances, otherwise the warranty will be void.
The product should not be placed where it is exposed to rain, excessive moisture or grease.
Do not bend the power cord excessively or place heavy objects on it.
Do not use a damaged power cord or power outlet.
Do not place the unit near any naked flames such as a candle, or any heated source such as
a fire place or heater.
Dispose off batteries used for the unit in the proper manner.
Do not expose the unit to excessive heat, such as sunshine and fire.
Disposal of Old Electrical & Electronic Equipment (Applicable in the European Union and other European
countries with separate collection systems)
This Symbol on the battery or on the packaging indicates that the battery provided with this product shall
not be treated as household waste. On certain batteries this symbol might be used in combination with a
chemical symbol. The chemical symbols for mercury (Hg) or lead (Pb) are added if the battery contains
more than 0.0005% mercury or 0.004% lead. By ensuring these batteries are disposed of correctly, you
will help prevent potentially negative consequences for the environment and human health which could
otherwise be caused by inappropriate waste handling of the battery. The recycling of the materials will
help to conserve natural resources.
Specification
Output Power (THD10%): 1.5 Watts x 2
Speaker Unit: 1.5" x 2
Frequency Response: 175Hz~15KHz
Rated Load Impedance: 4Ω
Power Rating: AC 100-240V~50/60Hz, 500mA
DC 5V, 2000mA
Power Consumption: 5W
Viewing the DATE/Alarm 1/Alarm 2 setting
Operating Instructions
WARRANTY PROCEDURE
v1.5.2: DEC 2011
Please read the owner’s manual carefully and ensure that you have followed the correct installation and operating
procedures.
1. Please read this warranty card.
2. Keep your purchase receipt to enable you to proceed quickly in the event of a Warranty Service.
3. If you require Warranty Service, please contact the TEAC Customer Support Hotline at 1300 553 315 for
assistance. Please ensure that you have the model number, serial number and purchase receipt ready when
you call.
Please complete the section below and keep this inf ormation for your own records.
Own er’s Name
Own er’s Address
Postcode
Model Name/No. Serial N o.
Dealer’s N ame
Dealer’s Address
Postcode
Authorised Service Centres in Major Australian Cities
NSW
151 Arthur Street
Homebush W est, NSW 2140
Queen sland
Unit 1, 320 Curtin Ave W est
Eagle Farm, QLD 4009
Western Australia
Unit 2, 50 P ilbara Street
Welshpool, WA 6106
South Australia
11 McInnes Street
Ridleyton, SA 5008
Victoria
282 Normanby Road
South Melbourne, VIC 3205
Thank you for selecting a TEAC product
.
If you should require assistance with your product regarding its setup
or operation, or if any difficulties arise, please call us directly for advice
between Monday to Friday at 8.30AM – 6PM AEST at the
TEAC Customer Support Hotline
1300 553 315
teacservicesupport@awa.com.au
www.teac.com.au
WARRANTY INFORMATION
v1.5.2: DEC 2011
Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are
entitled to a replacement or refund for a major failure and for compensation for any other reasonably
foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail
to be of acceptable quality and the failure does not amount to a major failure.
Warranty T erms & Conditions
1. TEAC warrants that this product is free from defects in material and workmanship under normal domestic use with
reasonable care and skill. Maintenance and cleaning (i.e. laser head) is not covered by this warranty. The TEAC
warranty only applies to TEAC products purchased, used and serviced in Austr alia.
2. The benefits to the consumer given by this Warranty are in addition to other rights and remedies of the consumer
under a law in relation to goods or services to which the warranty relates, being the Australian Consumer Law.
3. Refund or replacement via your retailer is available for a period of 14 days after purchase for goods that have been
inspected and determined to have a major failure. Refund and exchange is not applicable for change of mind.
4. Subject to the terms herein, this warranty effectively covers the equipment as specified in the Warranty Periods
Table below from the date of p urchase.
TEAC PRODUCT
WARRANTY PERIOD
LED/LCD TV 32” (80 cm) and above
1 Year (In-Hom e Service/ Pick up A vailable)*
All other T EAC products
1 Year (Carry-in Service)
5.
This service will only be provided as part of this warranty if all the following conditions are met;
In Home Ser vice/Pick up* Ser vice
a) The product is indicated in the Warranty Period Table.
b) The product is within the warranty peri od.
c) The product is located within the norm al service area of t he local TEAC Auth orised Service Centr e.
If TEAC d etermines that th e product is not r epairable on site, TEAC can c omplete the repair by taking th e product to
a TEAC Aut horised Service Centre.
Where In-H ome service/Pick up* is not a vailable, the purc haser is required to send th e product to the nearest TEAC
Authorised Service Centre for repair. In this event, proof of purchase is required to support a warranty claim. After
the repair, the product will be available for collection by or return to the purchaser at a fee upon request. TEAC in-
home servic e can be made available at a fee u pon request.
Carr y-in Service
6. A 12-month replac ement warranty is applicable to all Accessories suc h as Remote, Power A daptors and Cables.
7. TEAC will ensur e to the best of its abilities that all required parts are made available for any required servic e/repair.
8. TEAC Australia Pty Ltd and its Authorised Service Centres will use their best endeavours to complete product
repairs within a reasonable period based on available resources and workload during the time when service is
requested and performed.
9. Refurbished parts may be used to repair the product. In the case of a replacement, the product may be replaced,
with a refurbished unit of the same type or, if one is unavailable, a similar refurbished model with equal or better
features & s pecifications.
10. Please be advised that if the product presented f or repair is capable of retaining user-generated data, the data may
be lost during servicing. Customers are strongly encouraged to back up all important information/data before
sending th e product in for ser vice/repair.
11. Service will be provided only during normal business hours and under safety conditions and circumstances. TEAC
and its authorised service agents can refuse any repair if safety, in relation to OH&S, becomes a concern to its staff
or authorised service agents’ personnel.
12. The warranty is void and warranty claims may be refus ed, subject to the Australian Consumer Law, if:
a) The product was not tr ansported, installed, operated or maintained according to manufacturer instruction, or
b) The product was abused, damaged, tampered, altered or repaired by any unauthorised persons, or
c) Product failure is due to accidents during use, installation or transit, power surges, use of defective or
incompatible external devices, exposure to abnormal conditions such as excessive temperatures or humidity, or
entry of liquids, objects or creatures into the product.
13. No one is authorised to assume any liability on behalf of TEAC or impose any obligation on it, in connection with the
sale of any equipment other than as stated in this warranty and outlined above.
14. TEAC reserves the right to inspect and verify whether the product is exhibiting a major failure as claimed by
customers/r etailers.
15. LCD dead pixel polic y, please contact T EAC Customer Support Hotline on 1300 553 315 for assistance.
/