Elitegroup P55H-CM Specification

Preface

Copyright

This publication, including all photographs, illustrations and software, is protected

any of the material contained herein, may be reproduced without written consent of

the author.

Version 1.0

Disclaimer

The information in this document is subject to change without notice. The manufac-

turer makes no representations or warranties with respect to the contents hereof and

specifically disclaims any implied warranties of merchantability or fitness for any

particular purpose. The manufacturer reserves the right to revise this publication and

to make changes from time to time in the content hereof without obligation of the

manufacturer to notify any person of such revision or changes.

Trademark Recognition

Microsoft, MS-DOS and Windows are registered trademarks of Microsoft Corp.

MMX, Pentium, Pentium-II, Pentium-III, Celeron are registered trademarks of Intel

Corporation.

Other product names used in this manual are the properties of their respective

owners and are acknowledged.

Federal Communications Commission (FCC)

This equipment has been tested and found to comply with the limits for a Class B

digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful interference in a residential installa-

tion. This equipment generates, uses, and can radiate radio frequency energy and, if

not installed and used in accordance with the instructions, may cause harmful inter-

ference to radio communications. However, there is no guarantee that interference

will not occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined by turning the

equipment off and on, the user is encouraged to try to correct the interference by one

or more of the following measures:

• Reorient or relocate the receiving antenna

• Increase the separation between the equipment and the receiver

• Connect the equipment onto an outlet on a circuit different from that to

which the receiver is connected

• Consult the dealer or an experienced radio/TV technician for help

Shielded interconnect cables and a shielded AC power cable must be employed with

this equipment to ensure compliance with the pertinent RF emission limits governing

this device. Changes or modifications not expressly approved by the system’s manu-

facturer could void the user’s authority to operate the equipment.

ii

Preface

Declaration of Conformity

This device complies with part 15 of the FCC rules. Operation is subject to the

following conditions:

• This device may not cause harmful interference, and

• This device must accept any interference received, including interfer-

ence that may cause undesired operation

Canadian Department of Communications

This class B digital apparatus meets all requirements of the Canadian Interference-

causing Equipment Regulations.

Cet appareil numérique de la classe B respecte toutes les exigences du Réglement sur

le matériel brouilieur du Canada.

About the Manual

The manual consists of the following:

Describes features of the

motherboard.

Go to

H

page 1

Describes installation of

motherboard components.

Go to

H

page 7

Provides information on us-

ing the BIOS Setup Utility.

Go to

H

page 27

Go to

H

page 47

Describes the motherboard

software

Chapter 2

Installing the Motherboard

Chapter 1

Introducing the Motherboard

Chapter 3

Using BIOS

Chapter 4

Using the Motherboard Software

Describes the Intel

®

Matrix

Storage Manager RAID Con-

figurations

Chapter 5

Intel

®

Matrix Storage Manager

RAID Configurations

Go to

H

page 51

Chatper 6

Trouble Shooting

Provides basic troubleshoot-

ing tips

H

page 57

Go to

iii

Chapter 2

7 7

7

Installing the Motherboard 7

Safety Precautions............................................................................7

Choosing a Computer Case.............................................................7

Installing the Motherboard in a Case............................................7

Checking Jumper Settings...............................................................8

Setting Jumpers.......................................................................8

Checking Jumper Settings.......................................................9

Jumper Settings.......................................................................9

Installing Hardware...................................................................10

Installing the Processor.........................................................10

Installing Memory Modules...................................................12

Expansion Slots......................................................................16

Connecting Optional Devices................................................18

Installing a Hard Disk Drive/CD-ROM/SATA Hard Drive...21

Connecting I/O Devices.................................................................22

Connecting Case Components.....................................................23

Front Panel Header...............................................................26

TT

T

ABLE OF CONTENTSABLE OF CONTENTS

ABLE OF CONTENTS

Preface i

Chapter 1 1

Introducing the Motherboard 1

Introduction...................................................................................1

Feature............................................................................................2

Specifications................................................................................4

Motherboard Components..........................................................5

Chapter 3 27

Using BIOS 27

About the Setup Utility........................ ......................................... 27

The Standard Configuration...................................................27

Entering the Setup Utility.......................................................27

Resetting the Default CMOS Values...................................28

Using BIOS......................................................................................29

Standard CMOS Setup..........................................................30

Advanced Setup.....................................................................32

Advanced Chipset Setup.........................................................35

Integrated Peripherals...........................................................36

Power Management Setup.....................................................37

PCI/PnP Setup.......................................................................39

iv

PC Health Status...................................................................39

Frequency/Voltage Control....................................................42

Load Default Settings............................................................43

Supervisor Password............................................................43

User Password......................................................................44

Save & Exit Setup...................................................................44

Exit Without Saving.................................................................44

Updating the BIOS..................................................................45

Chapter 4

47 47

47

Using the Motherboard Software 47

About the Software DVD-ROM/CD-ROM.................................47

Auto-installing under Windows XP/Vista/7...............................47

Running Setup.......................................................................48

Manual Installation........................................................................50

Utility Software Reference........................................................50

Chapter 5

51 51

51

Intel

®

Matrix Storage Manager RAID Configurations

51

Before creating a RAID set...........................................................51

Entering Intel

®

Matrix Storage Manager RAID BIOS utility...52

Creating a RAID set.......................................................................53

Deleting a RAID set.......................................................................55

Resetting disks to Non-RAID......................................................56

Exiting Setup...................................................................................56

Chapter 6

57 57

57

Trouble Shooting 57

Start up problems during assembly............................................57

Start up problems after prolong use.............................................57

Maintenance and care tips.............................................................58

Basic Troubleshooting Flowchart................................................59

1

Introducing the Motherboard

Chapter 1

Introducing the Motherboard

Introduction

Thank you for choosing the P55H-CM motherboard. This motherboard is a high

performance, enhanced function motherboard designed to support the LGA1156

socket for Intel

®

Lynnfield processor for high-end business or personal desktop

markets.

This motherboard is based on Intel

®

P55 Express Chipset for best desktop platform

solution. P55 is a single-chip, highly integrated, high performance Hyper-Threading

peripheral controller, unmatched by any other single chip-device controller. This

motherboard supports up to 8 GB of system memory with dual channel DDR3 1333/

1066 MHz. One PCI slot is supported, fully compliant with PCI rev 2.3 specification

at 33MHz. High resolution graphics via one PCI Express slot, intended for Graphics

Interface, is fully compliant to the PCI Express Base Specification revision 2.0. It

implements an EHCI compliant interface that provides twelve USB 2.0 ports (six

USB ports and three USB 2.0 headers support additional six USB ports). It supports

Intel

®

Matrix Storage Technology, providing both AHCI and RAID 0, 1, 5 and 10

configuration.

The motherboard is equipped with advanced full set of I/O ports in the rear panel,

including PS/2 mouse and keyboard connectors, LPT1, one LAN port, six USB ports,

and audio jacks for microphone, line-in and line-out.

2

Introducing the Motherboard

Feature

• Accommodates Intel

®

Lynnfield processor

• Supports “Hyper-Threading” technology CPU

“Hyper-Threading” technology enables the operating system into thinking

it’s hooked up to two processors, allowing two threads to be run in parallel, both

on separate “logical” processors within the same physical processor.

The motherboard uses an LGA1156 type of socket that carries the following

features:

Processor

The Intel P55 Express Chipset is a single-chip with proven reliability and per-

formance.

Chipset

• Supports DDR3 1333/1066 DDR3 SDRAM with Dual-channel architec-

ture

• Accommodates four unbuffered DIMMs

• Up to 2 GB per DIMM with maximum memory size up to 8 GB

• Supports 1 Gb, 2 Gb and 4 Gb DDR3 DRAM technologies for x8 and x16

devices (It is not recommended to use 512 Mb DDR3 memory device on

this motherboard)

Memory

• Support Intel

®

Matrix Storage Technology, providing both AHCI and RAID

0, 1, 5 and 10 configuration.

• One x16 PCI Express Gen2 ports each supporting up to 8 GB/s direc-

tion peak bandwidth

• Compliant with PCI Rev 2.3 interface at 33 MHz

• Integrated SATA 3.0 Gb/s Host Controller

• Twelve USB 2.0 ports supported

• Serial Peripheral Interface (SPI) support

• Enhanced DMA Controller, interrupt controller, and timer functions

Audio (optional)

• 5.1 Channel High Definition Audio Codec

• ADCs support 44.1k/48k/96kHz sample rate

• Meets Microsoft WLP 3.10 Vista premium and mobile PCs audio

requirements

• Direct Sound 3D

TM

compatible

• 5.1Channel High Definition Audio Codec

• Exceeds Microsoft Windows Logo Program (WLP) Requirements

• ADCs support 44.1K/48K/96K/192KHz sample rate

• Power Support: Digital: 3.3V; Analog: 5.0V

• 7.1 + 2 channel High Definition Audio Codec

• All DACs Support 192k/96k/48k/44.1kHz DAC sample rate

• High –quality analog differential CD input

• Meets Microsoft WHQL/WLP 3.0 audio requirements

• Direct Sound 3D

TM

compatible

3

Introducing the Motherboard

The motherboard comes with the following expansion options:

• One PCI Express x16 slot for Graphic Interface

• Two PCI Express x1 slots

• One 32-bit PCI v2.3 compliant slot

• Six 7-pin SATA connectors

• One floppy disk drive interface

Expansion Options

The motherboard has a full set of I/O ports and connectors:

Integrated I/O

• Two PS/2 ports for mouse and keyboard

• One LAN port

• Six USB ports

• One parallel port

• Audio jacks for microphone, line-in and line-out

The firmware can also be used to set parameters for different processor clock

speeds.

• Power management

• Wake-up alarms

• CPU parameters

• CPU and memory timing

BIOS Firmware

This motherboard uses AMI BIOS that enables users to configure many system

features including the following:

1. Some hardware specifications and software items are subject to change

without prior notice.

2. Due to chipset limitation, we recommend that motherboard be operated

in the ambiance between 0 and 50 °C.

Onboard LAN

• IEEE 802.3 Ethernet interface for 1000BASE-T, 100BASE-TX and

10BASE-T applications

• Integrated 10/100/1000 transceiver

• Operates at half of the PCI Express Specification v1.1 speed

4

Introducing the Motherboard

• Intel P55 Express Chipset

• LGA1156 socket for latest Intel

®

Lynnfield processor

• Supports “Hyper-Threading” technology CPU

• Dual-channel DDR3 memory architecture

• 4 x 240-pin DDR3 DIMM sockets support up to 8 GB

• Supports DDR3 1333/1066/800 DDR3 SDRAM

• 1 x PCI Express Gen2 x16 slot

• 2 x PCI Express x1 slots

• 1 x PCI slot

• Supported by Intel P55 Express Chipset

• 6 x Serial ATA 3.0 Gb/s Host Controllers

• Supports RAID 0, 1, 5 and 10

• Realtek ALC 662 6CH HD audio (Colay ALC888/VIA VT1708B)

• 1 x PS/2 keyboard & PS/2 mouse connector

• 1 x parallel port

• 6 x USB ports

• 1 x RJ45 LAN connector

• 1 x Audio port (Line in, microphone in, and line out)

• 1 x 24-pin ATX Power Supply connector, 4-pin 12V connec-

tor

• 6 x Serial ATA connectors

• 3 x USB 2.0 headers support additional 6 USB ports

• 1 x Clear CMOS header

• 1 x Front panel header

• 2 x COM headers

• 1 x SPDIF out header

• 1 x Front panel audio header

• 1 x TCM header

• CPU_FAN/SYS_FAN/PWR_FAN connectors

Chipset

Memory

Expansion

Slots

Storage

Audio

Giga LAN

Internal I/O

Connectors &

Headers

• AMI BIOS with 16Mb SPI ROM

• Supports Plug and Play 1.0A, APM 2.0, Multi Boot, DMI

• Supports ACPI revision 3.0B specification

System BIOS

Form Factor • Micro ATX Size, 244mm x 244mm

CPU

Specifications

Rear Panel I/O

• Intel 82578 Gigabit Lan Controller

5

Introducing the Motherboard

Motherboard Components

Table of Motherboard Components

LABEL COMPONENTS

1. CPU Socket

LGA1156 socket for Intel

®

Lynnfield processor

2. CPU_FAN CPU cooling fan connector

3. DIMM1~4 240-pin DDR3 SDRAM slots

4. PWR_FAN Power cooling fan connector

5. FDD1 Floppy disk drive connector

6. ATX1 Standard 24-pin ATX power connector

7. SATA1~6 Serial ATA connectors

8. F_PANEL Front panel switch/LED header

9. COM Onboard serial port header

10. CLR_CMOS Clear CMOS jumper

11. F_USB1~3 Front panel USB headers

12. TCM Trusted Cryptography Module header

13. SPDIFO SPDIF out header

14. F_AUDIO1 Front panel audio header

15. PCI1 32-bit add-on card slot

16. PCIE1X-1~2 PCI Express x1 slots

17. PCIE16X PCI Express slot for graphics interface

18. SYS_FAN System cooling fan connector

19. ATX_12V 4-pin +12V power connector

This concludes Chapter 1. The next chapter explains how to install the motherboard.

6

Introducing the Motherboard

Memo

7

Installing the Motherboard

Chapter 2

Installing the Motherboard

Safety Precautions

• Follow these safety precautions when installing the motherboard

• Wear a grounding strap attached to a grounded device to avoid dam-

age from static electricity

• Discharge static electricity by touching the metal case of a safely

grounded object before working on the motherboard

• Leave components in the static-proof bags they came in

• Hold all circuit boards by the edges. Do not bend circuit boards

Choosing a Computer Case

There are many types of computer cases on the market. The motherboard complies

with the specifications for the micro ATX system case. Some features on the

motherboard are implemented by cabling connectors on the motherboard to indica-

tors and switches on the system case. Make sure that your case supports all the

features required.

Most cases have a choice of I/O templates in the rear panel. Make sure that the I/O

template in the case matches the I/O ports installed on the rear edge of the

motherboard.

This motherboard carries a micro ATX form factor of 244 x 244 mm. Choose a case

that accommodates this form factor.

Installing the Motherboard in a Case

Refer to the following illustration and instructions for installing the motherboard in

a case.

Most system cases have mounting brackets installed in the case, which correspond

the holes in the motherboard. Place the motherboard over the mounting brackets

and secure the motherboard onto the mounting brackets with screws.

Ensure that your case has an I/O template that supports the I/O ports and expansion

slots on your motherboard.

8

Installing the Motherboard

Checking Jumper Settings

This section explains how to set jumpers for correct configuration of the motherboard.

Setting Jumpers

Use the motherboard jumpers to set system configuration options. Jumpers with

more than one pin are numbered. When setting the jumpers, ensure that the jumper

caps are placed on the correct pins.

The illustrations show a 2-pin jumper. When

the jumper cap is placed on both pins, the

jumper is SHORT. If you remove the jumper

cap, or place the jumper cap on just one pin,

the jumper is OPEN.

This illustration shows a 3-pin jumper. Pins

1 and 2 are SHORT.

SHORT OPEN

Do not over-tighten the screws as this can stress the motherboard.

9

Installing the Motherboard

Checking Jumper Settings

The following illustration shows the location of the motherboard jumpers. Pin 1 is

labeled.

Jumper Settings

Jumper

Type

Description Setting (default)

CLR_CMOS

3-pin

Clear CMOS

1-2: NORMAL

2-3: CLEAR CMOS

Before clearing the

CMOS, make sure to

turn off the system.

1

CLR_CMOS

To avoid the system unstability after clearing CMOS, we recommend users

to enter the main BIOS setting page to “Load Default Settings” and then

“Save and Exit Setup”.

10

Installing the Motherboard

Installing Hardware

Installing the Processor

Caution: When installing a CPU heatsink and cooling fan make sure that

you DO NOT scratch the motherboard or any of the surface-mount resis-

tors with the clip of the cooling fan. If the clip of the cooling fan scrapes

across the motherboard, you may cause serious damage to the motherboard

or its components.

On most motherboards, there are small surface-mount resistors near the

processor socket, which may be damaged if the cooling fan is carelessly

installed.

Avoid using cooling fans with sharp edges on the fan casing and the clips.

Also, install the cooling fan in a well-lit work area so that you can clearly

see the motherboard and processor socket.

Before installing the Processor

This motherboard automatically determines the CPU clock frequency and system bus

frequency for the processor. You may be able to change the settings in the system

Setup Utility. We strongly recommend that you do not over-clock processors or

other components to run faster than their rated speed.

This motherboard has an LGA1156 socket. When choosing a processor, consider the

performance requirements of the system. Performance is based on the processor

design, the clock speed and system bus frequency of the processor, and the quantity

of internal cache memory and external cache memory.

Warning:

1. Over-clocking components can adversely affect the reliability of the

system and introduce errors into your system. Over-clocking can perma-

nently damage the motherboard by generating excess heat in components

that are run beyond the rated limits.

2. Always remove the AC power by unplugging the power cord from the

power outlet before installing or removing the motherboard or other

hardware components.

11

Installing the Motherboard

A. Opening of the Load Plate

· Put your thumb on the tail of the load

plate and press the tail down.

· Rotate the load plate to fully open

position.

B. Disengaging of the Load Lever

· Hold the hook of lever and pull it to the

left side to clear retention tab.

· Rotate the load lever to fully open

position.

C. Removing the Cap

· Be careful not to touch the contact at

any time.

D. Inserting the Package

· Grasp the package. Ensure to grasp on

the edge of the substrate.

· Make sure pin 1 indicator is on your

bottom-left side.

· Aim at the socket and place the package

carefully into the socket by purely

vertical motion.

E. Closing the Load Plate

· Rotate the load plate onto the package

IHS (Intergraded Heat Spreader).

· Engage the load lever while pressing

down lightly onto the load plate.

· Secure the load lever with the hook

under retention tab.

F. Fasten the cooling fan supporting base

onto the CPU socket on the motherboard.

G. Make sure the CPU fan is plugged to the

CPU fan connector. Please refer to the

CPU cooling fan user’s manual for more

detail installation procedure.

CPU Installation Procedure

The following illustration shows CPU installation components.

12

Installing the Motherboard

Installing Memory Modules

This motherboard accommodates four memory modules. It can support four 240-pin

DDR3 1333/1066. The total memory capacity is 8 GB.

You must install at least one module in any of the four slots. Total memory capacity

is 8 GB.

DDR3 SDRAM memory module table

Memory module Memory Bus

DDR3 1066 533 MHz

ff

Channel A: DDR3_1, DDR3_2

Channel B: DDR3_3, DDR3_4

The four DDR3 memory sockets (DDR3_1, DDR3_2, DDR3_3 and DDR3_4) are

divided into two channels and each channel has two memory sockets as following:

1. To achieve better airflow rates and heat dissipation, we suggest that

you use a high quality fan with 3800 rpm at least. CPU fan and

heatsink installation procedures may vary with the type of CPU fan/

heatsink supplied. The form and size of fan/heatsink may also vary.

2. DO NOT remove the CPU cap from the socket before installing a

CPU.

3. Return Material Authorization (RMA) requests will be accepted

only if the motherboard comes with the cap on the LGA1156 socket.

Due to Intel CPU spec definition, the system will not boot if only one

DIMM is installed in DDR3_1 or DDR3_3. Follow the table above for

recommended memory configuration.

DDR3_1 DDR3_2 DDR3_3 DDR3_4

2 DIMMs - Populated - Populated

3 DIMMs Populated Populated Populated

4 DIMMs Populated Populated Populated Populated

Mode

Sockets

Recommend memory configuration

ff

DDR3 1333 667 MHz

13

Installing the Motherboard

Do not remove any memory module from its antistatic packaging

until you are ready to install it on the motherboard. Handle the

modules only by their edges. Do not touch the components or metal

parts. Always wear a grounding strap when you handle the modules.

Installation Procedure

Refer to the following to install the memory modules.

1 This motherboard supports unbuffered DDR3 SDRAM .

2 Push the latches on each side of the DIMM slot down.

3 Align the memory module with the slot. The DIMM slots are keyed with

notches and the DIMMs are keyed with cutouts so that they can only be

installed correctly.

4 Check that the cutouts on the DIMM module edge connector match the

notches in the DIMM slot.

5 Install the DIMM module into the slot and press it firmly down until it

seats correctly. The slot latches are levered upwards and latch on to

the edges of the DIMM.

6 Install any remaining DIMM modules.

1. For best performance and compatibility, we recommend that users

give priority to the yellow DIMMs (DDR3_2/DDR3_4) when install-

ing DIMMs.

2. We suggest users not mix memory type. It is recommended to use

the same brand and type memory on this motherboard.

14

Installing the Motherboard

Table A: DDR3 (memory module) QVL (Qualified Vendor List)

The following DDR3 1800/1600/1333/1066 memory modules have been tested and

qualified for use with this motherboard.

Type Size Vendor Module Name

ELPIDA

PC3-8500U-7-00-AP

Hynix HYMT164U64ZNF8-G8 AA

512MB

Micron

MT4JTF6464AY-1G1B1

A-data

M3OSS3H3I3120B5Z

Aeneon

AEH760UD00-10FA98X

Corsair

CM3X1024-1066C7

HYMT112U64ZNF8-G8 AA

Hynix

HMT112U6AFP8C-G7N0 AA

Kingston

KVR1066D3N7/1G

MT8JTF12864AY-1G1D1

Micron

MT8JTF12864AY-1G1D1

IMSH1GU03A1F1C-10G B2S81427034

Qimonda

IMSH1GU03A1F1C-10F B2S81427023

Ramaxel RMR1810NA48E7F-1066-LF

1GB

Samsung

Golden Bar M378B2873DZ1-CF8 0818

HYMT125U64ZNF8-G8 AA

Hynix

HMT125U6AFP8C-G7N0 AA

MT16JTF25664AY-1G1D1

Micron

MT16JTF25664AY-1G1D1

IMSH2GU13A1F1C-10F B3S81427044

Qimonda

IMSH2GU13A1F1C-10G B3S81528005

DDR3 1066

2 GB

Samsung

M378B5673DZ1-CF8 0842

A-data

AD31333001GOU(AD63I1A08)

Aeneon AXH760UD00-13GA98X

Apacer

AHU02GFA33C9N1C

Hynix

HMT112U6AFP8C-H9N0 AA

KingMax

FLFD45F-B8KG9 NAES

Kingston

KVR1333D3N9/1G

Micron

MT8JTF12864AY-1G4D1

Qimonda

IMSH1GU13A1F1C-13H

Ramaxel

RMR1810KD48E7F-1333

Samsung

M378B2873EH1-CH9

1 GB

Samsung

M378B2873DZ1-CH9

A-data

AD31333002GOU(AD63I1B16)

Elixir M2F2G64CB8HA4N-CG 0903.TW

Hynix

HMT125U6AFP8C-H9N0 AA

KingMax

FLFE85F-B8KG9 NEES

Kingston

KVR1333D3N9/2G

Micron

MT16JTF25664AY-1G4D1

Qimonda

IMSH2GU13A1F1C-13H B3S81124001

DDR3 1333

2 GB

Samsung

M378B5673EH1-CH9

15

Installing the Motherboard

User please be noted that DDR3 1800/1600 MHz is validated to run at

1333Mhz only.

Type Size Vendor Module Name

DDR3 1600 1GB

Kingston

KHX12800D3K3/3GX

DDR3 1800 1 GB

KingMax KHX14400D3K3/3GX

16

Installing the Motherboard

Installing Add-on Cards

The slots on this motherboard are designed to hold expansion cards and connect them

to the system bus. Expansion slots are a means of adding or enhancing the

motherboard’s features and capabilities. With these efficient facilities, you can in-

crease the motherboard’s capabilities by adding hardware that performs tasks that are

not part of the basic system.

Before installing an add-on card, check the documentation for

the card carefully. If the card is not Plug and Play, you may

have to manually configure the card before installation.

This motherboard is equipped with one standard PCI slot. PCI

stands for Peripheral Component Interconnect and is a bus stan-

dard for expansion cards, which for the most part, is a supple-

ment of the older ISA bus standard. The PCI slot on this board

are PCI v2.3 compliant.

PCI1 Slot

PCIEX16 Slots

The PCI Express x16 slot is used to install an external PCI

Express graphics card that is fully compliant to the PCI Express

Base Specification revision 2.0.

The PCI Express x1 slots are fully compliant to the PCI Ex-

press Base Specification revision 2.0.

PCIE1X-1~2

Slots

Expansion Slots

Page is loading ...

Elitegroup P55H-CM Specification

Elitegroup P55H-CM Specification

Related papers

Other documents