Shure 526T Series II Super Punch User manual

Brand: Shure

Model: 526T Series II Super Punch

Category: Motorcycle Accessories

Type: User manual

This manual is also suitable for

526T

Shure 526T Series II Super Punch is a high-quality, transistorized base station microphone designed to provide crystal-clear transmission and enhanced reliability. Its dynamic microphone with a transistorized preamplifier ensures crisp, undistorted voice response, while the adjustable volume control allows for optimum intelligibility. The microphone features a momentary or locking press-to-talk transmit/receive switch for ease of use and a rugged, high-impact ARMO-DUR case for durability in demanding operating conditions.

TRANSISTORIZED BASE STATION MICROPHONE

GENERAL

The Shure Model 526T Series II SUPER PUNCH



base

station microphone is designed for clearer transmission and

improved reliability. This transistorized microphone can be

used to replace ceramic or dynamic, high- or low-impedance

microphones supplied as original equipment.

Model 526T Series II provides crisp, undistorted voice re-

sponse with adjustable volume control for optimum intelligi-

bility of transmission.

The microphone is designed for maximum versatility in

base station operation. It has a momentary or locking press-

to-talk transmit/receive switch for greatest ease of use, and

a modulation level volume control for highest undistorted

output with high- or low-impedance inputs. The supplied six-

wire cable and triple-pole double-throw switch are arranged

for universal microphone-transceiver connection.

The microphone is not affected by heat or humidity, and it

is oustanding in its ability to resist mechanical shocks and

vibration. Its exclusive ARMO-DUR



case is immune to oil,

grease, fumes, salt spray, sun, rust, and corrosion. The “Mil-

lion Cycle” leaf-type press-to-talk switch is designed to with-

stand rigorous operating conditions and constant use.

Microphone Features:

S Dynamic microphone with transistorized preamplifier

S Adjustable volume control for optimum transmiter

modulation and maximum intelligibility

S Replaces either ceramic or dynamic original equip-

ment microphones

S Excellent response for single-sideband transmission

S Uses readily available 9-volt battery—low current

drain for long life

S Low hum pickup, minimum susceptibility to RF inter-

ference

S Momentary or locking press-to-talk transmit/receive

switch –”Million Cycle” leaf-type

S Universal six-wire cable for instant microphone-trans-

ceiver connection

S Sturdy, high-impact ARMO-DUR



case

S Rugged and dependable under all operating

conditions

BATTERY INSTALLATION

Model 526T Series II uses a 9 Vdc battery (90AJ1371).To

install the battery, proceed as follows:

1. Loosen two screws (located underneath base) holding

battery retaining clip, and remove battery retaining

clip.

2. Connect terminal strap to battery.

3. Insert battery in VELCRO strap of battery retaining

cllip and fasten VELCRO strap.

4. Insert battery retaining clip in base and tighten screws

securely.

CONNECTIONS

Model 527T Series II can be connected to an input (trans-

ceiver, transmitter, or amplifier) of 500 ohms or more. For de-

tailed instructions for connecting the 526T Series II to CB or

ham transceivers. If your unit is not listed in the Guide, con-

tact your dealer or Shure Incorporated for information.

A piece of tubing is attached to the plug end of the cable

for use as a strain relief for plugs with large cable entry holes.

Remove the tubing when not required.

The internal connections of Model 526T Series II are as

shown in Figure 1.

Model 526T Series II Super Punch



Microphone User Guide

27B1468 (AI)

2001, Shure Incorporated

Printed in Mexico

9Vdc

The general wiring procedure for tranceiver connections

is as follows:

Microphone Audio Input Circuit:

1. Connect the WHITE cable lead to the microphone au-

dio input terminal.

2. Connect the SHIELD to chassis or circuit ground of

the transceiver (see Guide and CAUTION

below).

Electronic or Relay Switching Circuit:

GROUNDED SWITCHING

Most transceivers employ a grounded circuit to switch

from the receive to the transmit position. To connect the mi-

crophone to such a circuit, proceed as follows:

1. At the end of the cable, connect the RED lead to the

terminal used to complete the transmitter circuit.

2. Connect the BLUE lead to chassis or circuit ground of

the transceiver (see Guide and CAUTION below).

3. Connect the YELLOW lead to the terminal used to

complete the receiver circuit. This will usually be a

ground return from the loudspeaker circuit. If a micro-

phone switching contact is not required for loudspeak-

er ground, insulate (wrap with tape) the YELLOW

lead.

4. The BLACK lead is usually not used; insulate the

BLACK lead. However, if both a receiver ground and a

loudspeaker ground are required, connect the YEL-

LOW lead to loudspeaker ground, and the BLACK

lead to the receiver ground.

ISOLATED SWITCHING

In some transceivers, an isolated circuit is required to

switch power supply voltages rather than grounds. If an iso-

lated switching circuit is required, proceed as follows:

1. At the end of the cable, connect the RED lead to the

isolated switch contact terminal used to complete the

transmitter circuit.

2. Connect the BLUE lead to the terminal used for the

switched power supply.

3. Connect the BLACK lead to the terminal used to com-

plete the receiver circuit. If the power supply is not

switched to the receiver circuit by a microphone

switching contact, insulate (wrap with tape) the

BLACK lead.

4. Connect the YELLOW lead to the loudspeaker ground

return. If a microphone switching contact is not re-

quired for the loudspeaker ground, insulate the YEL-

LOW cable lead.

CAUTION

Make certain that the SHIELD and/or the BLUE lead are

not connected to chassis ground for those models where the

Guide specifies they should be connected to circuit ground.

SPECIAL SWITCHING

In some transceivers, special switching circuits are re-

quired. Three types are described below. In all of the types,

before making the required circuit alterations, remove the

microphone baseplate by unscrewing the two screws secur-

ing it.

1. If a grounded audio input is required in the receive

mode, solder a jumper lead between switch terminal 9

and the ground lug (see Figure 1).

2. If both and isolated and grounded transmit circuit are

required, along with a grounded receive circuit (see

Figure 1):

a) Unsolder the WHITE leads from switch terminals 7

and 8.

b) Solder the WHITE leads together, and insulate the

connection.

c) Cut the BLACK cable lead from terminal 1 and sol-

der it to terminal 8.

d) Solder a jumper lead between terminal 7 and the

ground lug.

At the end of the cable, the BLUE and RED leads are now

the isolated transmit leads; the BLACK lead is the grounded

transmit lead; and the YELLOW lead is the grounded receive

lead.

3. If both an isolated and grounded receive circuit are

required, along with a grounded transmit circuit (see

Figure 1):

a) Unsolder the WHITE leads from switch terminals 7

and 8.

b) Solder the WHITE leads together, and insulate the

connection.

c) Unsolder the RED cable lead from terminal 3 and

solder it to terminal 8.

d) Solder a jumper lead between terminal 7 and the

ground lug.

At the end of the cable, BLACK and BLUE leads are now

the isolated receive leads; the YELLOW lead is the

grounded receive lead; and the RED lead is the grounded

transmit lead.

VOLUME CONTROL

When the 526T Series II replaces a dynamic (usually low–

impedance) microphone supplied as original equipment, the

volume control should be set at the lower ranges to prevent

overmodulation and unintelligible transmission. Correct

modulation can be checked on the modulation level indicator.

When the 526T Series II replaces a ceramic (usually high-

impedance) microphone supplied as original equipment, the

volume control should be set at the upper ranges for correct

modulation as indicated on the modulation level indicator.

WARNING

Too high a volume control setting causes over-

modulation, interference, channel splatter, and

unintelligible voice transmission. Carefully check

the volume control setting.

LOCKING PRESS-TO-TALK SWITCH

The fingertip control bar of the press-to-talk switch can be

used in a momentary or locked-on position. For use as a mo-

mentary switch, depress the control bar and release after

transmission. To lock the switch in the On position, depress

the control bar and move it forward with the fingertips. To un-

lock the switch, move the control bar backward and remove

pressure.

Polar Pattern

Omnidirectional

Output Impedance

5,000 ohms

Load Impedance

500 ohms minimum

Output Level (At 1,000 Hz with 100 kilohm load)

Adjustable from 0.61 to 16 mV for 1 microbar input

Signal Handling Capability (With 50 kilohm load)

111 dB SPL at 1,000 Hz produces 1.0V with volume con-

trol at maximum

Battery Type

9 Vdc

Battery Drain

0.9 mA

Battery Life

300 hours minimum, replace after 1 year

Switches

Press-to-talk: Single-bar, momentary or locking, leaf-type

triple-pole, double-switch

Cable

2.1m (7 ft) five conductor, one-conductor shielded, rubber

jacketed, attached, coiled cable

Case

Black, high-impact ARMO-DUR



Dimensions

See Figure 3

Net Weight

920 grams (2 lb)

Packaged Weight

1.2 kilograms (2 lb. 11 oz)

Replacement Parts

Cartridge R96. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Grille Assembly 90D1844. . . . . . . . . . . . . . . . . . . . . . . . . .

Battery Retaining Clip 90A2351. . . . . . . . . . . . . . . . . . . . .

Baseplate 53A1459A. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Coiled Cable 70A544. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Switch Blade Assembly (6-blade) 90A2595. . . . . . . . . . .

Switch Blade Assembly (4-blade) 90A3510. . . . . . . . . . .

Press-to-talk Control Bar 65A1279A. . . . . . . . . . . . . . . . .

Volume Control 46A060. . . . . . . . . . . . . . . . . . . . . . . . . . .

Printed Circuit Assembly 90A2721. . . . . . . . . . . . . . . . . .

SHURE Incorporated Web Address: http://www.shure.com

222 Hartrey Avenue, Evanston, IL 60202–3696, U.S.A.

Phone: 847-866–2200 Fax: 847-866-2279

In Europe, Phone: 49-7131-72140 Fax: 49-7131-721414

In Asia, Phone: 852-2893-4290 Fax: 852-2893-4055

Elsewhere, Phone: 847-866–2200 Fax: 847-866-2585

Shure 526T Series II Super Punch User manual

Brand: Shure

Model: 526T Series II Super Punch

Category: Motorcycle Accessories

Type: User manual

This manual is also suitable for

526T

Download PDF

report

Shure 526T Series II Super Punch User manual

This manual is also suitable for

Shure 526T Series II Super Punch User manual

Related papers

Other documents