Dell M3800 Owner's manual

Dell Precision M3800

Owner's Manual

Regulatory Model: P31F

Regulatory Type: P31F001

Notes, Cautions, and Warnings

NOTE: A NOTE indicates important information that helps you make better use of your computer.

CAUTION: A CAUTION indicates either potential damage to hardware or loss of data and tells you

how to avoid the problem.

WARNING: A WARNING indicates a potential for property damage, personal injury, or death.

Trademarks used in this text: Dell

™

, the Dell logo, Dell Boomi

™

, Dell Precision

™

, OptiPlex

™

, Latitude

™

, PowerEdge

™

,

PowerVault

™

, PowerConnect

™

, OpenManage

™

, EqualLogic

™

, Compellent

™

, KACE

™

, FlexAddress

™

, Force10

™

,

Venue

™

and Vostro

™

are trademarks of Dell Inc. Intel

®

, Pentium

®

, Xeon

®

, Core

®

and Celeron

®

are registered

trademarks of Intel Corporation in the U.S. and other countries. AMD

®

is a registered trademark and AMD Opteron

™

,

AMD Phenom

™

and AMD Sempron

™

are trademarks of Advanced Micro Devices, Inc. Microsoft

®

, Windows

®

,

Windows Server

®

, Internet Explorer

®

, MS-DOS

®

, Windows Vista

®

and Active Directory

®

are either trademarks or

registered trademarks of Microsoft Corporation in the United States and/or other countries. Red Hat

®

and Red Hat

®

Enterprise Linux

®

are registered trademarks of Red Hat, Inc. in the United States and/or other countries. Novell

®

and

SUSE

®

are registered trademarks of Novell Inc. in the United States and other countries. Oracle

®

is a registered

trademark of Oracle Corporation and/or its affiliates. Citrix

®

, Xen

®

, XenServer

®

and XenMotion

®

are either registered

trademarks or trademarks of Citrix Systems, Inc. in the United States and/or other countries. VMware

®

, vMotion

®

,

vCenter

®

, vCenter SRM

™

and vSphere

®

are registered trademarks or trademarks of VMware, Inc. in the United States

or other countries. IBM

®

is a registered trademark of International Business Machines Corporation.

2013 -12

Rev. A00

Contents

1 Working on Your Computer.................................................................................5

Before Working Inside Your Computer.............................................................................................5

Turning off Your Computer.............................................................................................................. 6

Using power buttonUsing charms.............................................................................................. 6

After Working Inside Your Computer............................................................................................... 6

2 Removing and Installing Components..............................................................9

Recommended Tools........................................................................................................................9

System Overview...............................................................................................................................9

Removing the Base Cover...............................................................................................................10

Installing the Base Cover.................................................................................................................12

Removing the System Badge Flap...................................................................................................12

Installing the System Badge Flap.....................................................................................................13

Removing the Battery......................................................................................................................14

Installing the Battery....................................................................................................................... 14

Removing the Memory Module(s)...................................................................................................14

Installing the Memory Module(s).....................................................................................................15

Removing the Touchpad.................................................................................................................15

Installing the Touchpad.................................................................................................................. 16

Removing the Hard Drive................................................................................................................16

Installing the Hard Drive..................................................................................................................17

Removing the Speakers ..................................................................................................................18

Installing the Speakers.................................................................................................................... 18

Removing the WLAN Card.............................................................................................................. 19

Installing the WLAN Card................................................................................................................ 19

Removing the Coin-Cell Battery.................................................................................................... 20

Installing the Coin-Cell Battery...................................................................................................... 20

Removing the mSATA Card............................................................................................................ 20

Installing the mSATA Card...............................................................................................................21

Removing the Fans .........................................................................................................................22

Installing the Fans........................................................................................................................... 22

Removing the Heatsink...................................................................................................................23

Installing the Heatsink.....................................................................................................................23

Removing the Power Connector....................................................................................................24

Installing the Power Connector......................................................................................................24

Removing the Input/Output (I/O) Board........................................................................................ 25

Installing the I/O Board...................................................................................................................25

Removing the System Board...........................................................................................................25

Installing the System Board.............................................................................................................27

Removing the Keyboard................................................................................................................. 28

Installing the Keyboard................................................................................................................... 30

Removing the Display Assembly ....................................................................................................30

Installing the Display Assembly.......................................................................................................32

Removing the Palmrest Assembly...................................................................................................33

Installing the Palmrest Assembly.................................................................................................... 34

3 System Setup.........................................................................................................37

Boot Sequence................................................................................................................................ 37

Navigation Keys...............................................................................................................................37

System Setup Options.....................................................................................................................38

Updating the BIOS ..........................................................................................................................42

System and Setup Password...........................................................................................................42

Assigning a System Password and Setup Password................................................................. 43

Deleting or Changing an Existing System and/or Setup Password..........................................43

4 Diagnostics............................................................................................................45

Enhanced Pre-Boot System Assessment (ePSA) Diagnostics........................................................ 45

Device Status Lights........................................................................................................................46

Battery Status Lights....................................................................................................................... 46

5 Technical Specifications.....................................................................................47

6 Contacting Dell.................................................................................................... 53

1

Working on Your Computer

Before Working Inside Your Computer

Use the following safety guidelines to help protect your computer from potential damage and to help to

ensure your personal safety. Unless otherwise noted, each procedure included in this document

assumes that the following conditions exist:

• You have read the safety information that shipped with your computer.

• A component can be replaced or--if purchased separately--installed by performing the removal

procedure in reverse order.

WARNING: Before working inside your computer, read the safety information that shipped with

your computer. For additional safety best practices information, see the Regulatory Compliance

Homepage at www.dell.com/regulatory_compliance

CAUTION: Many repairs may only be done by a certified service technician. You should only

perform troubleshooting and simple repairs as authorized in your product documentation, or as

directed by the online or telephone service and support team. Damage due to servicing that is not

authorized by Dell is not covered by your warranty. Read and follow the safety instructions that

came with the product.

CAUTION: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or

by periodically touching an unpainted metal surface, such as a connector on the back of the

computer.

CAUTION: Handle components and cards with care. Do not touch the components or contacts on

a card. Hold a card by its edges or by its metal mounting bracket. Hold a component such as a

processor by its edges, not by its pins.

CAUTION: When you disconnect a cable, pull on its connector or on its pull-tab, not on the cable

itself. Some cables have connectors with locking tabs; if you are disconnecting this type of cable,

press in on the locking tabs before you disconnect the cable. As you pull connectors apart, keep

them evenly aligned to avoid bending any connector pins. Also, before you connect a cable,

ensure that both connectors are correctly oriented and aligned.

NOTE: The color of your computer and certain components may appear differently than shown in

this document.

To avoid damaging your computer, perform the following steps before you begin working inside the

computer.

1. Ensure that your work surface is flat and clean to prevent the computer cover from being

scratched.

2. Turn off your computer (see Turning Off Your Computer).

3. If the computer is connected to a docking device (docked) such as the optional Media Base or

Battery Slice, undock it.

5

CAUTION: To disconnect a network cable, first unplug the cable from your computer and

then unplug the cable from the network device.

4. Disconnect all network cables from the computer.

5. Disconnect your computer and all attached devices from their electrical outlets.

6. Close the display and turn the computer upside-down on a flat work surface.

NOTE: To avoid damaging the system board, you must remove the main battery before you

service the computer.

7. Remove the main battery.

8. Turn the computer top-side up.

9. Open the display.

10. Press the power button to ground the system board.

CAUTION: To guard against electrical shock, always unplug your computer from the electrical

outlet before opening the display.

CAUTION: Before touching anything inside your computer, ground yourself by touching an

unpainted metal surface, such as the metal at the back of the computer. While you work,

periodically touch an unpainted metal surface to dissipate static electricity, which could harm

internal components.

11. Remove any installed ExpressCards or Smart Cards from the appropriate slots.

Turning off Your Computer

CAUTION: To avoid losing data, save and close all open files and exit all open programs before you

turn off your computer.

You can turn off your computer in two ways :

1. Using the power button

2. Using the charms menu

Using power button

1. Press and hold the Power button to turn off the screen.

Using charms

1. Swipe from the right edge of the display to access the Charms menu.

2. Touch Settings —> Power —> Shut down to turn off the computer.

After Working Inside Your Computer

After you complete any replacement procedure, ensure you connect any external devices, cards, and

cables before turning on your computer.

6

CAUTION: To avoid damage to the computer, use only the battery designed for this particular Dell

computer. Do not use batteries designed for other Dell computers.

1. Connect any external devices, such as a port replicator, battery slice, or media base, and replace

any cards, such as an ExpressCard.

2. Connect any telephone or network cables to your computer.

CAUTION: To connect a network cable, first plug the cable into the network device and then

plug it into the computer.

3. Replace the battery.

4. Connect your computer and all attached devices to their electrical outlets.

5. Turn on your computer.

7

8

2

Removing and Installing Components

This section provides detailed information on how to remove or install the components from your

computer.

Recommended Tools

The procedures in this document may require the following tools:

• Small flat-blade screwdriver

• #0 Phillips screwdriver

• #1 Phillips screwdriver

• T5 Torx screwdriver

• Small plastic scribe

System Overview

Figure 1. Inside View — Back

1. power connector

2. system fan

3. system board

4. hard drive

5. speakers

6. battery

7. I/O board cable

8. I/O board

9. WLAN card

10. video-card fan

9

11. memory modules 12. heatsink

Figure 2. Front View

1. keyboard

2. touchpad

3. palmrest

4. display

Removing the Base Cover

1. Follow the procedures in

Before Working Inside Your Computer

.

2. Close the display and turn the computer over.

3. Turn the system badge flap over and place it on the base cover.

10

4. Remove the screws that secure the base cover to the computer. Release and remove the base

cover from the computer.

NOTE: To remove the screws from the base cover, use a T5 Torx screwdriver.

5. Lift up and remove the base cover from the computer.

11

Installing the Base Cover

1. Place the base cover on the computer and snap it in place.

2. Tighten the screws to secure the base cover to the computer.

3. Turn the system badge flap over and snap it in place.

4. Follow the procedures in

After Working Inside Your Computer

.

Removing the System Badge Flap

1. Follow the procedures in

Before Working Inside Your Computer

.

2. Remove the base cover.

3. Turn over the base cover and peel the Mylar tape that secures the system badge flap to the base

cover.

12

4. Flip the base cover and release the tab on the system badge flap from the slot on the base cover.

Lift the system badge flap off the base cover.

Installing the System Badge Flap

1. Slide the tab on the system badge flap into the slot on the base cover and snap the system badge

flap into place.

2. Turn the base cover over and affix the Mylar tape that secures the system badge flap to the base

cover.

3. Follow the procedures in

After Working Inside Your Computer.

13

Removing the Battery

1. Follow the procedures in

Before Working Inside Your Computer

.

2. Remove the base cover.

3. Perform the following steps to remove the battery:

a) Disconnect the battery cable from the system board [1].

b) Remove the screws that secure the battery to the computer.

c) Lift the battery off the computer [2].

Installing the Battery

1. Place and align the battery in the battery bay.

2. Tighten the screws that secure the battery to the computer.

3. Connect the battery cable to the system board.

4. Install the base cover.

5. Follow the procedures in

After Working Inside Your Computer.

Removing the Memory Module(s)

1. Follow the procedures in

Before Working Inside Your Computer

.

2. Remove the:

a) base cover

b) battery

3. Pry the securing clips away from the memory module until it pops-up. Remove the memory

module from its connector on the system board.

14

Installing the Memory Module(s)

1. Insert the memory module into the memory socket.

2. Press the memory module down until it clicks into place.

NOTE: If you do not hear the click, remove the memory module and re-install it.

3. Install the:

a) battery

b) base cover

4. Follow the procedures in

After Working Inside Your Computer

.

Removing the Touchpad

1. Follow the procedures in

Before Working Inside Your Computer

.

2. Remove the:

a) base cover

b) battery

3. Lift up the latch [1] and disconnect [2] the touchpad cable from the system board. Remove the

screws that secure the touchpad to the computer.

4. Slide out the touchpad and lift it away from the computer.

15

Installing the Touchpad

1. Align the touchpad in its position on the computer.

2. Tighten the screws to secure the touchpad to the computer.

3. Connect the touchpad cable to the system board.

4. Install the:

a) battery

b) base cover

5. Follow the procedures in

After Working Inside Your Computer

.

Removing the Hard Drive

1. Follow the procedures in

Before Working Inside Your Computer

.

2. Remove the:

a) base cover

b) battery

3. Perform the following steps to remove the hard drive from the computer:

a) Disconnect the hard-drive cable from the system board [1].

b) Remove the screws that secure the hard drive to the computer.

c) Lift the hard drive off the computer [2].

16

4. Perform the following steps to remove the hard-drive bracket:

a) Disconnect the hard-drive cable from the hard drive [1].

b) Remove the screws that secure the hard-drive bracket to the hard drive.

c) Lift the hard drive off the hard-drive bracket [2].

Installing the Hard Drive

1. Align the screw holes on the hard drive-bracket with the screw holes on the hard drive.

2. Tighten the screws that secure the hard-drive bracket to the hard drive.

3. Connect the hard-drive cable to the hard drive.

4. Place the hard drive on its slot on the computer.

5. Tighten the screws to secure the hard drive to the computer.

17

6. Connect the hard-drive cable to the system board.

7. Install the:

a) battery

b) base cover

8. Follow the procedures in

After Working Inside Your Computer.

Removing the Speakers

1. Follow the procedures in

Before Working Inside Your Computer

.

2. Remove the:

a) base cover

b) battery

3. Perform the following steps to remove the speaker:

a) Disconnect the speaker cable from the system board [1].

b) Unroute the speaker cable and remove the cable from the routing tabs [2].

c) Remove the screw that secures the speakers to the computer.

d) Lift the speakers, along with the speaker cable, off the computer [3].

Installing the Speakers

1. Align the speakers in the slot on the computer.

2. Route the speaker cable through the routing tabs on the computer.

3. Tighten the screw to secure the speakers to the computer.

4. Connect the speaker cable to the system board.

5. Install the:

a) battery

b) base cover

6. Follow the procedures in

After Working Inside Your Computer

.

18

Removing the WLAN Card

1. Follow the procedures in

Before Working Inside Your Computer

.

2. Remove the:

a) base cover

b) battery

3. Perform the following steps to remove the WLAN card:

a) Remove the screw to release the bracket that secures the WLAN card to the computer. Lift the

bracket away from the computer.

b) Disconnect the antenna cables from the WLAN card.

c) Slide and remove the WLAN card from its connector on the I/O board.

Installing the WLAN Card

1. Align the notch on the WLAN card with the tab on the WLAN-card connector on the I/O board.

2. Align the bracket which secures the WLAN card to the palmrest assembly.

3. Connect the antenna cables to the WLAN card.

CAUTION: To avoid damage to the WLAN card, do not place any cables under it.

NOTE: The color of the antenna cables is visible near the tip of the cables. The antenna-cable

color scheme for the WLAN card supported by your computer is as follows:

Table 1. Antenna-Cable Color Scheme for the WLAN Card

Connectors on the WLAN card Antenna-cable color

Main (white triangle) white

Auxiliary (black triangle) black

4. Tighten the screw to secure the bracket and the WLAN card to the palmrest assembly.

5. Install the:

a) battery

b) base cover

6. Follow the procedures in

After Working Inside Your Computer.

19

Removing the Coin-Cell Battery

1. Follow the procedures in

Before Working Inside Your Computer

.

CAUTION: Removing the coin-cell battery re-sets the BIOS settings to default. It is

recommended that you note the BIOS settings before removing the coin-cell battery.

2. Remove the:

a) base cover

b) battery

c) WLAN card

3. Perform the following steps to remove the coin-cell battery:

a) Disconnect the coin-cell battery cable from the I/O board [1].

b) Lift up and remove the coin-cell battery from the computer [2].

Installing the Coin-Cell Battery

1. Replace the coin-cell battery in its slot in the computer.

2. Connect the coin-cell battery cable to the I/O board.

3. Install the:

a) WLAN card

b) battery

c) base cover

4. Follow the procedures in

After Working Inside Your Computer

.

Removing the mSATA Card

1. Follow the procedures in

Before Working Inside Your Computer

.

2. Remove the:

a) base cover

20

Page is loading ...

Dell M3800 Owner's manual

Dell M3800 Owner's manual

Related papers

Other documents