Infocus IN5552L User manual

Brand: Infocus

Model: IN5552L

Category: Data projectors

Type: User manual

Declaration of Conformity

Manufacturer: InFocus Corporation, 13190 SW 68th Parkway, Portland, Oregon

97223-8368 USA

We declare under our sole responsibility that this projector conforms to the

following directives and norms:

EMC Directive 2004/108/EC

ErP Directive 2009/125/EC

EMC: EN 55022: 2010

EN 55024: 2010

EN 61000-3-2: 2006+A2:2009

EN 61000-3-3:2008

Low Voltage Directive 2006/95/EC

Safety: IEC 60950-1:2005; EN 60950-1:2006+A12:2011

Trademarks

Apple, Macintosh, and PowerBook are trademarks or registered trademarks of

Apple Computer, Inc. IBM is a trademark or registered trademark of International

Business Machines, Inc. Microsoft, PowerPoint, and Windows are trademarks or

registered trademarks of Microsoft Corporation. Adobe and Acrobat are

trademarks or registered trademarks of Adobe Systems Incorporated. DLP® and the

DLP logo are registered trademarks of Texas Instruments and BrilliantColor™ is a

trademark of Texas Instruments. InFocus, In Focus, and INFOCUS (stylized) are

either registered trademarks or trademarks of InFocus Corporation in the United

States and other countries

NOTE: This product is covered electrical and electronic equipment

under the European Union's Waste from Electrical and Electronic

Equipment ("WEEE") Directive (2002/96/EC). The WEEE Directive

requires that covered equipment be collected and managed separately

from typical household waste in all EU member states. Please follow

the guidance of your local environmental authority or ask the shop

where you purchased the product for collection or recycling options.

FCC Warning

This device complies with part 15 of the FCC Rules. Operation is subject to the following

two conditions: (1) This device may not cause harmful interference, and (2) this device

must accept any interference received, including interference that may cause

undesired operation.

Note: This equipment has been tested and found to comply with the limits for a Class B

digital device, pursuant to part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses and can radiate radio frequency energy and, if not

installed and used in accordance with the instructions, may cause harmful interference

to radio communications. However, there is no guarantee that interference will not

occur in a particular installation. If this equipment does cause harmful interference to

radio or television reception, which can be determined by turning the equipment off

and on, the user is encouraged to try to correct the interference by one or more of the

following measures:

--Reorient or relocate the receiving antenna.

--Increase the separation between the equipment and receiver.

--Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

--Consult the dealer or an experienced radio/TV technician for help.

Changes or modifications not expressly approved by InFocus Corporation may void

authority to operate the equipment.

Canada

This Class B digital apparatus complies with Canadian ICES-003. Cet appareil

numérique de la classe B est conforme à la norme NMB-003 du Canada.

Agency Approvals

UL, cUL, TUV-GS, SASO, SABS, KC, NOM, PCT, PSB, UL-S(Argentina), C-tick, FCC and

Other specific Country Approvals may apply. Please see product certification label.

This document applies to regulatory models IN5552L, IN5554L, IN5555L, IN5852L,

IN5854L, and IN5855L.

Input ratings: AC 110-240V, 9-4A, 50-60Hz

InFocus reserves the right to alter product offerings and specifications at any time

without notice.

Table of Contents

Introduction 4

Positioning the projector 6

Ceiling Mount 7

Connecting power 8

Connecting a computer source 8

Displaying an image 9

Adjusting the image 10

Connecting a video device 11

Video device connections 11

Shutting down the projector 12

Troubleshooting your setup 12

Using the remote control 20

Using the keypad buttons 22

Using the menus 23

Input menu 24

Picture menu 25

Lamps menu 26

Alignment menu 27

Control menu 28

Service menu 29

Using Projector Web Controls 30

Maintenance 34

Cleaning the lens 34

Replacing the projection lamps 34

Replacing the lens 36

Replacing the filters 37

Changing the color wheel 38

Using the security lock 39

Appendix 40

Optional Lenses 40

PiP Compatibility 46

RS-232 commands 47

Index 54

Important Operating Considerations for Safety

• Refer to this guide for proper startup and shutdown procedures.

• Follow all warnings and cautions in this manual and on the projector.

• Do not block the lens with any object while the projector is being used.

ocking the light path can cause overheating and result in fire.

• Place the projector in a horizontal position no greater than 8 degrees off axis.

• Locate the projector at least 4' (1.2m) away from any heating or cooling vents.

• Do not block ventilation openings. Locate the projector in a well-ventilated

ea without obstructions to intake or exhaust vents. Do not place the

projector on a tablecloth or other soft covering that may block the vents.

• Do not place the projector in direct sunlight, humid, greasy or dusty places or

in places where the projector may come into contact with smoke or steam.

• Do not look directly into the lens while the projector is being used.

• Do not drop the projector.

• Do not spill liquid on the projector. Spilled liquid may damage the projector.

• Use the power cord provided. Connect the power cord to a receptacle with a

otective safety (earth) ground terminal. A surge-protected power strip is

recommended.

• Do not overload wall outlets.

• When disconnecting the power cord, hold the plug, not the cord.

• Wash hands after handling the cables supplied with this product.

• The projector remote control uses batteries. Make sure the batteries’ polarity

(+/-)

is aligned correctly. Dispose of used batteries in accordance with local

disposal laws.

• Use an InFocus approved ceiling mount kit for proper fitting, ventilation and

installation. The warranty does not cover any damage caused by use of non-

approved ceiling mount kits or by installing in an improper location.

• When the projector is ceiling mounted, wear protective eyewear to prevent

eye injury before opening lamp door.

• The projector must be installed by a qualified professional in order to ensure

proper operation and reduce the risk of hazards or injury. It is not

recommended you install the projector yourself.

• Refer all service to qualified service personnel. Servicing your own projector

can be dangerous to you and will void the warranty.

• Only use replacement parts specified by InFocus. Unauthorized substitutions

may result in fire, electrical shock, or injury, and may void the warranty.

• Only genuine InFocus lamps are tested for use in this projector. Use of non

Focus lamps may cause electrical shock and fire, and may void the projector

warranty.

• Hg – Lamp contains mercury. Manage in accordance with local

disposal laws. See www.lamprecycle.org.

• The projector uses a high-pressure mercury glass lamp. The lamp may fail

prematurely, or it may rupture with a popping sound if jolted, scratched, or

handled while hot. The risk of lamp failure or rupture also increases as the

lamp age increases; please replace the lamp when the Lamp LED is red.

• In the unlikely event of a lamp rupture, particles may exit through the

ojector vents. Please keep people, food, and drinks out of the “keep out”

area under and around the projector, as indicated by the illustration.

Follow these instructions to help ensure image quality and lamp life over the life of

the projector. Failure to follow these instructions may affect the warranty. For

complete details of the warranty, see the Safety/Warranty Booklet.

Introduction

Your new digital projector is simple to connect, easy to use, and straightforward to

maintain. It is a versatile projector that is flexible enough to fit almost any

installation scenario. The IN5552L and IN5852L have XGA 1024 x 768 resolution,

the IN5554L and IN5854L have WXGA 1280x800 resolution, and the IN5555L and

IN5855L have native WUXGA 1920x1200 resolution. This guide applies to all three

products. They are compatible with a wide variety of computers and video devices.

Note: These projectors do not ship with a lens. An optional lens must be chosen for

the product.

Product Specifications

To read the latest specifications on your multimedia projector, be sure to visit our

support website at www.infocus.com/support, as specifications are subject to

change.

Online Registration

your warranty and receive product updates, announcements, and registration

incentives.

Included Items

POWER

FOCUS ZOOM

LENS SHIFT

INPUT

AUTO SYNC

OVERSCAN

INFO. LIGHT

FREEZE

LAMP MODE

ASPECT PIP

PICTURE NETWORK

OFF

CLEAR SHUTTER ID SET

ENTER

789

EXIT

TEST

PATTERN

Remote Control

Power Cord

Optional RGBCMY

Color Wheel

Documentation

Dust Cap

Projector

RGB (VGA) Cord

Optional Accessories

Optional accessories include optional lenses and a ceiling mount. These items and

other accessories can be found on our website at www.infocus.com or at your

local dealer.

Lens

Remote control

receiver (IR)

Remote control

receiver (IR)

Elevator Foot

Color Wheel cover

Power switch

KeypadConnector panel

Power Cord

Connector

Connector Panel

The projector provides both computer and video connection options, including:

•HDMI

•DVI-D

• 3G-SDI

• BNC RGBHV and YPbPr for RGBHV, EDTV and HDTV

• RGB (VGA) computer

•S-video

• Composite video

The projector also provides the following connectors:

• LAN port for network control and web server.

• 12V screen trigger output

•Wired remote jack

• RS-232 connector for serial control. Command control codes are in the

pendix and on our support website at www.infocus.com/support.

12V Screen Trigger output

The 3.5mm mini-jack screen trigger provides a 12 volt, 0.25 amp DC output. It

turns on when the lamp is lit. If you connect your projection screen to this output

using the cable that came with your screen, the screen will move down when the

lamp is turned on and return to its storage position when the lamp is turned off.

RS-232

12V Screen Trigger

Output

Composite

video

RGBHV

YPbPr

HDMI

DVI-D

S-video

RGB

(VGA)

Wired

remote

LAN

SDI

Positioning the Projector

To determine where to position the projector, consider the size and shape of your

screen, the location of your power outlets, and the distance between the projector

and the rest of your equipment. Here are some general guidelines:

• Position the projector on a flat surface at a right angle to the screen. The

rojector (with the standard zoom lens, LENS-074) must be at 55.8”/

1.42m(XGA) ; 60.2”/1.53m (WXGA) ; 57.2”/1.45m (WUXGA) from the

projection screen. See appendix for additional lens information.

• Position the projector within 10 feet (3m) of your power source and within 6

eet (1.8m) of your video device (unless you purchase extension cables). To

ensure adequate cable access, do not place the projector within 6 inches

(.15m) of a wall or other object.

• Position the projector to the desired distance from the screen. The distance

from the lens of the projector to the screen, the zoom setting, and the video

format determine the size of the projected image.

• The image exits at a given angle. However, the lens shift feature makes the

image offset variable.

• The vertical image offset range for all the projectors is -60% to +20% (default

0%), and the horizontal image offset is +/-10% (default 0%). At 20% vertical

offset, the bottom of the image is 20% of the image height above the center

of the lens in a tabletop configuration.

Vertical Image Offset is -60-% ~ +20%

lens center

20% offset

-60% offset

Horizontal Image Offset is +/-10%

Ceiling Mount

If you wish to install the projector on the ceiling:

• The projector must be installed by a qualified professional in order to ensure

proper operation and reduce the risk of hazards or injury. It is not

recommended you install the projector yourself.

• We strongly recommend using InFocus approved ceiling mounts for proper

fitting, ventilation and installation. Refer to the ceiling mount installation

guide for more information. The warranty does not cover any damage caused

by use of non-approved ceiling mount kits or by installing in an improper

location.

• The ceiling must be strong enough to support the projector and the

installation must be in accordance with any local building codes. Consult your

dealer for more information.

• The maximum physical pitch is unlimited, however the lamp life will be

negatively affected.

• The maximum supported physical horizontal roll is +/-10º. Note: Lamp life will

be negatively affected.

• Keep all adjacent surfaces at least 19.7” (50cm) from the sides, 12” (30cm)

from the top and bottom of the projector, and 27.6” (70cm) from the back of

the projector to preserve required airflow around the projector.

10º

Connecting power

Connect the black power cord to the Power connector on the side of the projector

and to your electrical outlet. Turn on the power switch. The Power LED on the top

of the projector (page 12) turns red.

NOTES: Note: Connect

ion to a circuit with a minimum of 20A capacity is

recommended. Always use the power cord that shipped with the projector.

Connecting a computer source

HDMI 1.3 connection

Plug an HDMI cable into the video out connector on the video device and into the

HDMI connector on the projector.

To take advantage of HDMI 1.3 Deep Color (30

bit) you must have a 1.3-compatible

source.

DVI-D

Plug a DVI-D cable into the video out connector on the video device and into the

DVI connector on the projector.

RGB (VGA) connection

Connect one end of the provided computer cable to the RGB connector on the

projector and the other to the VGA connector on your computer. If you are using a

desktop computer, you will need to disconnect the monitor cable from the

computer’s video port first.

RGBHV connection

Connect one end of the BNC cable to the computer and the other end of the cable

into the BNC connectors on the projector.

Note: This projector does not support audio. Audio must be routed separately.

Connect power cord

MOLEX

Connect HDMI cable

Connect DVI-D cable

Connect RGB (VGA) cable

Connect RGBHV cable

Displaying an image

Touch the Power button on the keypad or the remote.

The Power button blinks green and the fans start to run. When the lamp turns on,

the

start up screen will display and the Power button will become solid green. It

can take a minute for the image to achieve full brightness.

No start up screen? Get help on page 13.

Turn on your computer or video device.

The image should appear on the projection screen. If it doesn’t, press the Inpu

button on the projector’s keypad or remote.

If you are using a laptop, make sure its external video port is active.

Many laptops do not automatically turn on their external video port when a

projector is connected. Usually a key combination like Fn + F8 or CRT/LCD key turns

the external display on and off. Locate a function key labeled CRT/LCD or a function

key with a monitor symbol. Press Fn and the labeled function key simultaneously.

Refer to your laptop’s documentation for more information about your laptop’s key

mbination.

No laptop image? T

ry pressing the Auto Sync button on the keypad or

remote. Get help on page 22.

Press Power button

Turn on computer or

video device

Activate laptop’s external port

Monitor key or

LCD/CRT key

Fn key

Adjusting the image

Position the projector to the desired distance from the screen at a 90 degree angle

to the screen. See the Appendix for screen sizes and distances associated with the

various lens options.

If the image is square but not centered on the screen or viewing area, adjust Zoom

or Le

ns Shift using the keypad or remote. Focus can also be adjusted using the

keypad or remote.

Rotate the elevator feet for adjustment of th

e projector’s height. Avoid placing

your hands near the hot exhaust vent at the back of the projector.

Adjust the Contrast or Brightness in the Picture menu. See page 25 for help with

these menu adjustments.

Adjust distance

Adjust zoom, focus and

lens shift.

Adjust height

Elevator feet

Adjust contrast and

brightness.

INPUT PICTURE LAMPS ALIGNMENT CONTROL SERVICE

Picture Mode < High Bright >

Contrast < 100 >

Brightness < 100 >

Adaptive Contrast < O >

Saturation < ------ >

Hue < ------ >

Gamma < Video >

Color < Enter >

Sharpness < 0 >

Noise Reduction < 0 >

Aspect Ratio < 16:10 >

Overscan < O >

VGA Setup Enter

Auto Sync Execute

Connecting a video device

You can connect video devices such as VCRs, DVD players, camcorders, digital

cameras, video game consoles, HDTV receivers, and TV tuners to the projector.

Note: This projector does not support audio. You must connect audio directly from

your source to a stereo or home theater system.

You can connect the projector to most video devices that can output video. You

cannot directly connect the coaxial cable that enters your house from a cable or

satellite company; the signal must pass through a tuner first. Examples of tuners

are digital cable boxes, VCRs, digital video recorders, and satellite TV boxes.

Basically, any device that can change channels is considered a tuner.

Although the aspect ratio is automatically selected by the projector based on the

signal input, you can change the aspect ratio, if desired. The projector’s Aspect

Ratio setting is accessed through the Aspect button on the remote or through the

projector’s Picture Menu. See

page 25 for more information.

Video device connections

No video cables are provided with the projector. You can order cables from InFocus

or use your own.

HDMI 1.3 connection

HDMI is a standard, uncompressed, all-digital audio/video interface. HDMI

provides an interface between sources, such as set-top boxes, DVD players, and

receivers and your projector. Plug an HDMI cable into the video out connector on

the video device and into the HDMI connector on the projector.

To take advantage of HDMI 1.3 Deep Color (30 bit) you must have a 1.3-compatible

source.

3G-SDI

Connect a BNC coaxial cable into the video device. Plug the other end of the cable

into the SDI In connector on the projector.

Component video connection

Plug a BNC type component cable into the video device. Plug the other end of the

component cable into the YPbPr connectors as appropriate.

In addition, a Component to VGA adapter can be used in conjunction with the VGA

connectors. Plug the component cable into the video device. Plug the other end of

the component cable into the adapter and plug the adapter into the RGB

connector.

Component offers the highest quality analog video output.

S-video connection

If your video device uses a round, four-prong S-video connector, plug an S-video

cable into the S-video connector on your video device and into the S-video

connector on the projector.

S-video delivers higher quality video output than composite.

Composite video connection

Plug the composite video cable’s yellow connector into the video out connector on

the video device. Plug the other yellow connector into the yellow Video

connector on the projector.

Composite Video output from composite connections is not as high quality as S-

video or as Component.

RGB (VGA) connection

If your video device has a 15-pin VGA output, plug one end of the included

computer cable into the VGA connector on your video source. Plug the computer

cable into the RGB connector on the projector.

3G-SDI Out

Connect one end of a BNC coaxial cable into the SDI Out connector on the

projector and the other end into another projector to daisy-chain the projectors.

Shutting down the projector

Auto Power Off

The projector has an Auto Power Off feature that automatically turns the projector

off if no active sources are detected and no user interaction with the projector is

performed for 20 minutes. By default, this feature is off.

Turning off the projector

To turn the projector off, press the Power button on the remote or keypad twice.

The lamp turns off and the LED blinks orange for 10 seconds while the fans

continue to run to cool the lamp. When the lamp has cooled, the LED lights red and

the fans stop. Unplug the power cable and turn off the power switch to completely

power off the projector.

Troubleshooting your setup

The Status Indicator LEDs on top of the projector indicates the state of the

projector and is helpful when troubleshooting.

Table 1: Status indicator LED behavior and meaning

LED Indicator Meaning

Power :

Solid red

Blinking green

Solid green

Blinking orange

The projector is plugged in.

The power button has been pressed and the software is

initi

alizing.

The projector is on and initialized.

The power button has been pressed to turn the projector

off and the fans ar

e running to cool the projector.

Status Turn the projector off and wait one minute, then turn the

ojector on again. If the Status LED turns on again, service

is required. Visit www.infocus.com/support to contact

service.

Lamp1/Lamp 2:

Flashing Green

Solid Green

Flashing Red

Solid Red

The lamp is warming up.

The lamp is on.

A lamp error occured. Turn the projector off and wait one

minu

te, then turn the projector on again. If the lamp light

turns on again, replace the lamp and reset the lamp timer

(page 35).

Note: the projector may need to be serviced.

The lamp needs to be replaced.

Te m p The projector is too hot. Make sure the vents aren’t blocked

(see page 18). Turn the projector off and wait one minute,

then turn the projector on again. Con

tact Technical Support

if the problem persists. Visit www.infocus.com/support to

contact service.

Shutter The shutter is closed. Press the Shutter button to open the

utter.

Problem Solution Result

No start up screen.

Plug the power cord into the projector, turn

on the power switch and press the power

button.

Correct image.

Only the start up screen appears.

Restart laptop

Press the Input button to

activate the laptop’s external port.

Computer image projected.

Problem Solution Result

No computer image, just the words “Signal

out of rang

e.”

Signal out

of range

Press the Auto Sync button on the keypad or remote.

To adjust computer refresh rate, go to Control Panel >

Display > Settings > Advanced > Adapter (location

varies by operating system).

You may also need to set a different resolution on your

computer, as shown in the following problem, “image

fuzzy or cropped.”

Computer image projected.

Only my laptop’s background appears, not the

Desktop icons.

Windows - Disable “Extend my Windows Desktop” in

Control Panel > Display > Settings > Display 2 (location

varies by operating system).

Uncheck this

option, then

click Apply

Background and Desktop projected.

Image fuzzy or cropped

For a laptop,

disable laptop

monitor or

turn-on dual-

display mode

Set your computer’s display resolution to the

native resolution of the projector (Start >

Settings > Control Panel > Display > Settings

tab).

Image clear and not cropped.

Image not centered on screen.

Adjust Lens Shift using the keypad or remote.

Correct image.

Problem Solution Result

Image not square. Adjust the angle of the projector, so that it is

square with the screen.

Square image.

Image not sharp.

INPUT PICTURE LAMPS ALIGNMENT CONTROL SERVICE

Picture Mode < High Bright >

Contrast < 100 >

Brightness < 100 >

Adaptive Contrast < O >

Saturation < ------ >

Hue < ------ >

Gamma < Video >

Color < Enter >

Sharpness < 0 >

Noise Reduction < 0 >

Aspect Ratio < 16:10 >

Overscan < O >

VGA Setup Enter

Auto Sync Execute

Adjust Sharpness in the Picture menu. Correct image.

Image does not fit 4:3 or 16:9 screen.

INPUT PICTURE LAMPS ALIGNMENT CONTROL SERVICE

Picture Mode < High Bright >

Contrast < 100 >

Brightness < 100 >

Adaptive Contrast < O >

Saturation < ------ >

Hue < ------ >

Gamma < Video >

Color < Enter >

Sharpness < 0 >

Noise Reduction < 0 >

Aspect Ratio < 16:10 >

Overscan < O >

VGA Setup Enter

Auto Sync Execute

Change Aspect Ratio to 4:3 or 16:9 in the Picture

menu.

Correct image.

Problem Solution Result

Image upside down.

INPUT PICTURE LAMPS ALIGNMENT CONTROL SERVICE

Projection Mode < Front >

Fan Mode < Normal >

Lens Control Enter

Lens Memory Enter

Center Lens Execute

Warp Enter

Blanking Enter

Edge Blend Enter

Turn Projection Mode to Front in the Alignment

menu.

Correct image.

Image reversed left to right.

INPUT PICTURE LAMPS ALIGNMENT CONTROL SERVICE

Projection Mode < Front >

Fan Mode < Normal >

Lens Control Enter

Lens Memory Enter

Center Lens Execute

Warp Enter

Blanking Enter

Edge Blend Enter

Turn Projection Mode to Front in the Alignment

menu.

Correct image.

COLOR

Projected colors don’t match source.

INPUT PICTURE LAMPS ALIGNMENT CONTROL SERVICE

Picture Mode < High Bright >

Contrast < 100 >

Brightness < 100 >

Adaptive Contrast < O >

Saturation < ------ >

Hue < ------ >

Gamma < Video >

Color < Enter >

Sharpness < 0 >

Noise Reduction < 0 >

Aspect Ratio < 16:10 >

Overscan < O >

VGA Setup Enter

Auto Sync Execute

Adjust color, tint, brightness, contrast in the

Picture menu and/or color space in the Input

menu.

COLOR

Correct image.

Problem Solution Result

The video embedded in my PowerPoint

presentation does not play on the screen

Turn off the internal LCD display on your laptop.

Embedded video plays correctly.

Te m p L E D

Lamp won’t turn on and the Temp LED is on. Make sure vents aren’t blocked, turn the

projector off and allow it to cool for one minute.

Lamp turns on.

Problem Solution Result

Still need assistance?

If you need assistance, visit our support website at www

.infocus.com/support

or call us. Check out the How To section for additional information on using this

projector for home theater or gaming applications.

This product is backed by a limited warranty. An extended warranty plan may be

rchased from your dealer. When sending the projector in for repair, we

recommend shipping the unit in its original packing material, or having a

professional packaging company pack the unit. Please insure your shipment for its

full value.

Lamps won’t turn on and the Lamp LEDs are

turne

d on.

Lamp LEDs

The





Replace

lamps

Lamp Doors

lamps must be replaced (see page 34).

Lamps turn on.

Problem Solution Result

Page is loading ...

Infocus IN5552L User manual

Brand: Infocus

Model: IN5552L

Category: Data projectors

Type: User manual

Download PDF

report

Infocus IN5552L User manual

Infocus IN5552L User manual

Related papers

Other documents