Umidigi G1 User manual

Brand: Umidigi

Model: G1

Type: User manual

Umidigi G1, with its Android™ 12 Go operating system, offers a user-friendly experience. Capture stunning photos with its 13MP+2MP rear camera and take beautiful selfies with the 5MP front camera. Enjoy smooth performance with its 4x ARM Cortex-A53 Mpcore up to 1.5GHz CPU and IMG 8XE 1PPC@ 570MHz GPU, along with 2GB of RAM and 32GB of ROM. Stay connected with 4G LTE connectivity and dual SIM card slots. The 5150mAh battery provides long-lasting power, while the 6.52-inch screen with 720x1600 Pixels resolution ensures an immersive viewing experience.

www.umidigi.com

Thanks for choosing UMIDIGl products

MP08

Amazon service Email:amazonservice@umidigi.com

Visit www.umidigi.com for more information

UMIDIGI is registered trademark by

Shenzhen Youmi Intelligent Technology Co., Ltd.

All other trademarks are the property of their

respective owner.

Language Catalogue

English

Screen

Light/Pro ximity Sensor

3.5 mm Headph one jack

Mic 1

Mic 2

Dual LED Flash

13MP Main

Depth-

of-field

Power Key

SIM/TF Slot

LTE

Nano S IM1

LTE

Nano S IM2

Mi cr o- SD

Nano S IM1

LTE

Android is a trademark of Google LLC.

13MP+2MP Camera

5MP Camera

6.52 inch

720x1600 Pixels

WAV/MP3/AAC/AMR/MIDI/APE/WMA,etc.

3GP/MPEG4,etc.

Band

Bluetooth 4.2

LTE FDD:B1/2/3/4/5/7/8/12/17/20/28A/28B

LTE TDD:B38/40/41

WCDMA:B1/2/4/5/8

GSM:B2/3/5/8

GNSS GPS, Beidou, Glonass,Galileo

Type-C

WIFI

SIM/TF card

USB Port

Bluetooth

Earphone Port

IEEE802.11 ac/a/b/g/n

2 Nano SIM Card Or 1 Nano SIM and 1 TF Card

1x Phone

1x Screen Protector (pre-applied)

1x Phone Case

1x Type-C Cable

1x Power Adapter

1x SIM Tray Ejector

1x Quick Start Guide

2GB

32GB

5150mAh

CPU

GPU

RAM

Operating System

ROM

Battery

Android™ 12 Go

4x ARM Cortex-A53 Mpcore up to 1.5GHz

IMG 8XE 1PPC@ 570MHz

FCC Caution: Any changes or modifications not expressly approved by the party

responsible for compliance could void the user's authority to operate this equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following

two conditions:

(1) This device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may

cause undesired operation.

This Product meets the government's requirements for exposure to radio waves. The

guidelines are based on standards that were developed by independent scientific

organizations through periodic and thorough evaluation of scientific studies.The standards

include a substantial safety margin designed to assure the safety of all persons regardless

of age or health.

FCC RF Exposure Information and Statement the SAR limit of USA (FCC) is1.6 W/kg

averaged over one gram of this Device C1 (FCC ID: 2ATZ4-G1C1F) has been tested

against this SAR limit. SAR information on this can be viewed on-line at http://

www.fcc.gov/oet/ea/fccid/. Please use the device FCC ID number for search. This device

was tested for typical operations 10mm from the body. To maintain compliance with FCC

RF exposure requirements, 10mm separation distance should. maintained to the user's

bodies

NOTE:

This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful interference

in a residential installation. This equipment generates, uses and can radiate radio

frequency energy and, if not installed and used in accordance with the instructions,

may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception,

which can be determined by turning the equipment off and on, the user is encouraged to

try to correct the interference by one or more of the followingmeasures:

-- Reorient or relocate the receiving antenna.

-- Increase the separation between the equipment and receiver.

-- Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

-- Consult the dealer or an experienced radio/TV technician for help.

Canadian regulatory statement

This device complies with Innovation, Science, and Economic Development Canada licence-exempt RSS

standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference,

and (2) this device must accept any interference, including interference that may cause undesired operation

of the device. Le présent appareil est conforme aux CNR d Innovation, Sciences et Développement

économique Canada applicables aux appareils radio exempts de licence. L exploitation est autorisée

aux deux conditions suivantes : (1) l appareil ne doit pas produire de brouillage, et (2) l utilisateur de

l appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d en

compromettre le fonctionnement. SAR Statement:

Mobile Phone has been tested and meets applicable limits for radio frequency (RF) exposure. Specific

Absorption Rate (SAR) refers to the rate at which the body absorbs RF energy. The SAR limit is 1.6 watts

per kilogram in Canada that set the limit averaged over 1 gram of tissue. During testing,

Model:A80 (IC: 26074-G1C1F) radios are set to their highest transmission levels and placed in positions that

simulate uses against the head, with no separation, and when worn or carried against the torso of the body,

with 10mm separation. To reduce exposure to RF energy, use a hands-free option, such as the built-in

speakerphone, the supplied headphones, or other similar accessories. Cases with metal parts may change the

RF performance of the device, including its compliance with RF exposure guidelines, in a manner that has

not been tested or certified. Although this device has been tested to determine SAR in each band of

operation, not all bands are available in all areas. Bands are dependent on your service provider’s wireless

and roaming networks.

5150-5250MHz is restricted to indoor use only.

Made in China

Follow UMIDIGI community.a place where

you can share and discuss with UMIDIGl

Manufacturer:

ShenzhenYoumiIntelligentTechnologyCo.,Ltd.

Add:406-407 Jinqi Zhigu Building,4/F,1 Tangling Road,

Nanshan District, Shenzhen City,Guangdong Province China

Umidigi G1 User manual

Umidigi G1 User manual

Related papers

Other documents