7 3/4"(197)
8 1/4"(209.5)
8 inches adjustable center hole distance
Wall mounted faucet using a pair of G1/2" female inlets with 2"flanges.
those inlets can adjust from 7 3/4"(197mm) to 8 1/4"(209.5),
allowing you to fit them directly onto your facility’s water lines with ease.
9.6"(245)
11.8"(300)
NPT1/2 2.8"(70)
19"(482)
8.6"(218)
19"(482)
MAX6.3"
(160)
NPT1/2 2.8"(70)
2.4"
(60)
21"(533)
25"(635)
43"(1100)
10"(250)
2.8"(70)
11"(280)
NPT1/2
40"(1016)
12.2"(310)
10"(250)
2.8"(70)
11"(280)
NPT1/2
36"(915)
MAX
6.3"
(160)
40"(1016)
7.7"(195)
47"(1194)
12"(300)
MAX
6.3"
(160)
2.8"(70)
11.8"(300)
NPT1/2
40"(1016)
21" Mini Pre Rinse Faucets 25" Mini Pre Rinse Faucets
36" Pre Rinse Faucets 47" Pre Rinse Faucets
6"(155)
43" Pre Rinse Faucets
inch(mm)
M22x1
Female
M22x1
Female
G1/2
Male
Attach supply lines (not included).
With 1.8 gpm are compliant with California water effi
ciency regulations,Complies \with California Proposition
65 and with the Federal Safe Drinking Water Act.
MAX
6.3"
(160)
10"(250)
11"(280)
MAX6.3"
(160)
16.2"(410)
1.Connect the two flanges (3) into the two inlets (5) . Screw them tightly.
2.Connect the body (1) to the flanges (3), do remember the gaskets (2) inside.
The two flanges (3) are adjustable inlets.
Unscrew the hexagon nut (4) on the flange (3) , rotate the flange(3) to the right the
distance and screw the hexagon thread back tightly.
You can adjust the distance from 7 3/4"to8 1/4".
3.Turn out the hexagon (6), Use the hexagon nut to lock the faucet and sink
4.Insert the short riser (2) to the body (1) ,
Screw the thread (3) tightly.
Connect the other side of the shorter riser (2)
with the add-on faucet (5),
Screw the thread (4) tightly.
5.Put the swing nozzle (3) into the add-on
faucet (1), screw the nut (2).
6.connect the longer riser (3) with the
other side of the add-on faucet (1),
Screw the thread (2) tightly.
7.Fix one side of the wall bracket
(4) onto the wall .
8.Unscrew the other side of the
wall bracket (1) and put the
longer riser inside (5).
Screw the other side of the
bracket (1) after adjusting the
height of the wall bracket.
9.Insert the brass tube (3) into
wall bracket (4),use the Allen
wrench to fix the brass tube (3)
and the bracket (4).
Distance from wall MAX 160mm.
Cut the brass tube (3) if the
faucet to the wall is <160mm.
10.Screw the hook (2) after
adjusting the height with the screwdriver.
160mm
11.Connect the other side of the longer
riser (1)to the flexible hose(5) , do remember
the gasket (3) inside and the connector (4)
must be tightly screwed.
Adjusting the height of the bracket(2).
11.Connect the other side of the fleible tube
(6) with the spray(8) , do remember
the gasket (7) inside .
1
2
3
4
5
6
3
2
1
2
3
45
1
3
2
1
1
32
4
5
5
3
2
4
1
6
7
8
FLUSH SYSTEM/CHECK FOR LEAKS.
Turn on hot and cold water supplies and flush
water lines for one minute.
Check all connections at arrows for leaks.
Retighten if necessary, but do not overtighten.
/
