DA-P

iskydance DA-P Owner's manual

  • Hello! I am an AI chatbot trained to assist you with the iskydance DA-P Owner's manual. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
Technical Parameters
1
User Manual Ver 1.0.0
Features
Input and Output
Operation temperature
Environment
Ta: -30
O
C ~ +55
O
C
Case temperature (Max.)
IP rating IP20
Ta: +75
O
C
Warranty
5 years
Warranty
Output current
Input voltage
Output voltage Gross weight
Size
Package
L60x W60 x H40mm
0.061kg
Model No.: DA-P
DALI Push Dimmer
Push Dim/Address programmability/Dim speed adjustable/Memory function
Small Dimmer for DALI Drivers or Ballasts.
Unidirectional and broadcasting communication.
Control by conventional push-button, with or without memory:
Short press: turn on /off light.
Long press: dimming up/down.
Dimming speed adjustable by rotary knob.
Max 0.05A
100-240VAC
100-240VAC
DAIL bus output 100mA max
Mechanical Structures and Installations
AC input
DAIL signal +
52.00 mm
52.00 mm
27.00 mm
Memory Setting button
DAIL signal -
Dimming speed adjust.
10x(0~9) for setting tens position
Memory status indicator
Rotary switches for setting DALI address,
the number equals to tens position plus units position
1x(0~9) for setting units position
AC push-button input
Wiring Diagram
Please carefully ensure all wire connections and polarities are correct and secure before applying power, otherwise this controller will be damaged.
Caution:
Push-button
L
N
100-240V~50/60Hz
L
N
DA+
DA-
DALI
Ballast or
Driver
L
N
DA+
DA-
DALI
Ballast or
Driver
Push-button function
Short press:
Turn on / off light.
Long press :
Dimming up/down
• DO NOT install with power applied to device.
• DO NOT expose the device to moisture.
Safety & Warnings
DALI address setting
1. Address value = Left rotary switch value × 10 + right rotary switch value.
For example : Left rotary switch value is 5, right rotary switch value is 4, Address value = 5 x 10 + 4 = 54.
2. Unicast mode : Address value 0-63 corresponds to DALI addresses 00-63.
Group mode : Address values 70-85 correspond to DALI groupings 0-15.
Broadcast mode : Left rotary switch value is 9.
PUSH dimming speed setting
1.The closer the arrow is to "+", the faster the PUSH dimming speed will be.
2. The closer the arrow is to "-", the slower the PUSH dimming speed will be.
Memory function setting
Short press the "SET" button to switch the memory function.
1. Without memory: LED indicator is red, PUSH dimming and then power on again, light returns to maximum brightness.
2. With memory: LED indicator is green, PUSH dimming and then power on again, light restores the last brightness.
Factory default: Without memory.
2
User Manual Ver 1.0.0
技术参数
特点
输⼊和输出
⼯作温度
环境
外壳最⾼温度
IP等级 质保
5年
质保
出电
⼊电
输出电压 ⽑重
尺⼨
包装
60x 60 x 40mm(⻓x宽x⾼)
0.061kg
型号:DA-P
DALI⾃
⾃复位开关调光/地址可编辑/调光速度可调/记忆功能
⽤于DALI驱动器或镇流器的调光器。
单播和⼴播通信。
通过 按键控制灯光带或不带亮度记忆功能:⾃复位开关
短按:打开/关闭灯光;
⻓按:调亮/调暗亮度。
调光速度可通过旋钮调节。
Max 0.05A
100-240VAC
100-240VAC
DAIL总线输出 100mA max
机械结构和安装
AC输⼊
DAIL信号+
52.00 mm
52.00 mm
27.00 mm
忆设
DAIL信号-
调光速度可调
10x(0~9)⽤于设置⼗位地址
记忆状态指⽰灯
⽤于设置DALI地址的旋转编码开关
1x(0~9)⽤于设置个位地址
AC⾃复位开关输⼊
接线图
在之前,所有线性正靠,否则光器
警告:
⾃复位开关
L
N
100-240V~50/60Hz
L
N
DA+
DA-
DALI
器或
动器
L
N
DA+
DA-
DALI
器或
动器
Ta: -30
O
C ~ +55
O
C
IP20
Ta: +75
O
C
1
版本1.0.0
景晴光电
⾃复位开关功能
:
打/关闭
⻓:
调/调暗
不要带电安装调光器。
不要将调光器安装在潮湿环境。
DALI地
1.地址值=左侧旋转开关值×10+右侧旋转开关值。
例如:左侧旋转开关值为5右侧旋转开关值为4地址值=5x10+4=54。
2.单播模式:地址值0-63对应DALI地址00-63。
组模式:地址值70-85对应于DALI组地址0-15。
⼴播模式:左侧旋转开关值为9。
1.箭头越靠近“+”⾃复位开关调光速度越快。
2.箭头越靠近“-”⾃复位开关调光速度越慢。
短按SET”键切换记忆功能。
1.⽆记忆功能:指⽰灯为红⾊⻓按⾃复位开关调节亮度后再重新上电灯光亮度恢复到最⼤亮度。
2.带记忆功能:指⽰灯为绿⾊⻓按⾃复位开关调节亮度后再重新上电灯光亮度恢复到调节的亮度。
出⼚默认⽆亮度记忆功能。
2
版本1.0.0
⼴州晴光电科技有限公司GuangzhouSkyacneCo.,Ltdwww.iskydance.cn
本资上的内容均经过认真核,如有任何印刷错或内容上的误解,本公保留最终解释权。
产品有技术改进,会编⼊新说明书中,恕不另通知
/