JELD-WEN 02959 Operating instructions

Brand: JELD-WEN

Model: 02959

Type: Operating instructions

This manual is also suitable for

2051120

JELD-WEN 02959 is a wood pocket door frame designed for use in new construction or remodeling projects. It is a pre-assembled frame that includes a top track, face jamb, and pocket frame. The frame is made of durable wood and is designed to be easy to install.

The JELD-WEN 02959 is a versatile frame that can be used in a variety of applications, including closets, bathrooms, and hallways. It is also a good choice for use in areas where space is limited, as it allows the door to be hidden away when not in use.

Features

Pre-assembled for easy installation
Durable wood construction

Features

Pre-assembled for easy installation
Durable wood construction

INSTALLATION INSTRUCTIONS

for Wood Pocket Door Frames (JII102)

Note to Installer: Provide a copy of these instructions to the building

owner. By installing this product, you acknowledge the terms and

conditions of the limited warranty as part of the terms of the sale.

Thank you for selecting JELD-WEN products. Attached are JELD-WEN’s

recommended installation instructions for Wood Pocket Door Frames.

Read these instructions thoroughly before beginning. They are designed

to work in most existing applications, however; existing conditions

may require changes to these instructions. If changes are needed, they

are made at the installer’s risk. For installations other than indicated in

these instructions, contact a building professional.

Estimated Install

Time for New

Construction

First Time: 3 hrs

Experienced: 2 hrs

Professional:

1 hr

SAFETY & HANDLING

SAFETY

Read and fully understand ALL manufacturers’ instructions before •

beginning.

Do not work alone. Two or more people are required. Use safe lifting •

techniques.

Wear protective gear (e.g. safety glasses, gloves, ear protection, etc.).•

Operate hand/power tools safely and follow manufacturer’s operating •

instructions.

Be cautious of plumbing and electrical lines when cutting into walls.•

MATERIALS & HANDLING

Inspect product for cosmetic damage and verify correct size.•

Heed material manufacturers’ handling and application instructions.•

Handle in vertical position; do not carry at or drag on oor.•

Do not put stress on joints, corners or frames.•

Store in dry, well-ventilated area in vertical, leaning position to allow •

air circulation; do not stack horizontally.

Protect from exposure to direct sunlight during storage.•

IF INJURY OCCURS, IMMEDIATELY SEEK MEDICAL ATTENTION!

INCLUDED PARTS

INCLUDED PARTS & NEEDED TOOLS

A - Face jamb

B - Top Track

C - Pre-assembled pocket frame

D - Wheel hanger

E - Adjusting bolt

F - Lock nut

G - Hanger bracket

H - (4) 1 1/2" pan head screws

I - Nylon guide

J - Adjusting wrench

NEEDED TOOLS

Tape measure•

Utility knife•

Level (4' minimum •

recommended)

Hammer•

Screw gun•

3 pound maul•

NEEDED MATERIALS

#10 x 2" screws•

Finishing supplies•

INSTALLATION INSTRUCTIONS

for Wood Pocket Door Frames (JII102)

1. Remove the old

door frame from

the wall. Cut back

the drywall to

match the new

opening.

2. Remove the oor

plate and non load-

bearing wall studs.

3. Frame the new

rough opening with

a new header and

jambs as needed.

4. Finish the top track

and face jamb as

desired. Attach the

top track to the pre-

assembled pocket

frame. The vertical

split jamb aligns

with top track.

Attach with screws.

5. Set pocket frame

and face jamb into

the rough opening.

Shim 4" from the

corners and at 24"

maximum intervals

until square, level,

and plumb.

6. Drive a #10 x 2"

screw through the

pocket frame and

each shim. Remove

the shipping blocks.

7. Attach the nylon

guide to the split

jamb with nails.

8. Install the hanger

brackets on top of

the door centered

at 2 1/2" from each

end.

9. Slide the rollers

into the top track.

10. Hang the door

in the track. Lift

and slide the

hanger bracket

onto the adjusting

bolt head. To

align door, turn

the adjusting

bolt head with

a wrench. When

nished adjusting,

tighten lock

nut down onto

bracket.

Please visit jeld-wen.com/resources for warranty, nishing instructions

and care and maintenance information.

Thank you for choosing

All other trademarks are the property of their respective owners.

(06/09)

INSTALL FRAME

New

opening

size

Existing

trim

Remove

drywall

Fastening

screw

Nylon

guide

Nail

Shipping block

Screw

Door

2 1/2"

Center

on door

Hanger

bracket

Hanger

bracket

Roller

Lock

nut

Adjusting

bolt head

Top track

Existing door

frame

Floor plate

Wall

stud

Top track

Pocket

frame

Face

jamb

Rotated

180

Vertical

split jamb

Shim

Shipping

block

Pocket

frame

JELD-WEN 02959 Operating instructions

Brand: JELD-WEN

Model: 02959

Type: Operating instructions

This manual is also suitable for

2051120

Features

Pre-assembled for easy installation
Durable wood construction

Download PDF

report

JELD-WEN 02959 Operating instructions

This manual is also suitable for

JELD-WEN 02959 Operating instructions

Related papers

Other documents