Home Styles 5660-30 Operating instructions

Brand: Home Styles

Model: 5660-30

Type: Operating instructions

Hardware List

Home Styles Consumer Assistance: www.homestyles-furniture.com,

[email protected], 888-680-7460, 877-831-0319

Extension Table

IMPORTANT NOTE

Carefully remove all the parts from the carton and put

them individually on a soft cloth to prevent scratches

or other damages occuring to the parts.

We have taken great care in the design of this

product and request that you carefully and strictly

follow our assembly instructions to ensure a

completed product as it was designed.

Part List

88 5660 30

Top

1pc

Top

1pc

Support

1pc

Pipe

1pc

Cover

1 pc.

Tools required for assembly : Phillips screwdriver

Head Cap Bolt

(Long)

4 pcs.(+1 extra)

Rail

1pc

Hex Wrench

4mm

1pc

Stretcher

1pc

Assembly Screw

4 pcs.(+1 extra)

Small Hex Wrench

4mm

1 pc.

Dowel

4 pcs.(+1 extra)

Cover

2 pcs.

Bali Hai

Head Cap Bolt

(Middle)

8 pcs.(+1 extra)

Wood Screw

(Long)

4 pcs.(+1 extra)

Head Cap Bolt

(Short)

8 pcs.(+1 extra)

Top

1pc

Block

2 pcs

Support

1pc

Support

2 pcs

Stretcher

1pc

Leg

2 pcs

Leg

2 pcs

Leg Support

1pc

Leg Support

1pc

Wood Screw

(Short)

2 pcs.(+1 extra)

Assembly Instructions 2/4

* Do not tighten up all the screws until each part is properly assembled.

* You should keep Hex Wrench in a safe place as you may need to tighten up the Head Cap Bolts in the future.

* Use a soft cloth between these parts and the floor.

STEP 1

Attach Stretcher (N) to Stretcher (O),

with Wood Screws (Short).

STEP 2

Attach Leg Supports (E) and (F) to Legs (I)

and (J) with Assembly Screws.

Attach Rail (L) to Leg Supports (E) and (F).

Attach unit from Step 1 to Legs (I) and (J) with

Head Cap Bolts (Middle).

IMPORTANT

Wood Screw (Short)

Head Cap Bolt (Middle)

STEP 3

Attach Blocks (D) to Pipe (M).

Attach Pipe into the pre-drilled holes of

Supports (G) and (H).

Attach Supports (K) to Supports (G) and (H)

with Head Cap Bolts (Middle).

Assembly Screw

Assembly Instructions 3/4

STEP 4

Attach Top (B) to unit from Step 3 with

Wood Screws (Long) into the pre-drilled holes.

Wood Screw (Long)

STEP 5

Place the unit from Step 2 in an upright position.

Attach unit from Step 4 to unit from Step 2

with Head Cap Bolts (Long) and Head Cap

Bolts (Short).

STEP 6

Attach Top (A) and (C) to unit by sliding into the groove in Supports (K).

Insert the Dowels into the holes of the rail in bottom side of Tops (A) and (C). (See figure 1)

Figure 1 (bottom view)

Dowel

Head Cap Bolt (Short)

Head Cap Bolt (Long)

Assembly Instructions 4/4

STEP 7

Put Covers into the holes of the top

when not using an umbrella.

Covers

Figure 2 (bottom view)

Open

Lock

To Shorten the Table

Open the locks under the top. (See Figure 2)

Pull the half tops slightly apart, fold up the center top and rotate it

so that it fits into the table base.

Push the half tops together.

Close the locks under the top. (See Figure 2)

Home Styles 5660-30 Operating instructions

Home Styles 5660-30 Operating instructions

Home Styles 5660-30 Operating instructions

Related papers