Barkan a Better Point of View ND400 Operating instructions

Barkan a Better Point of View
Brand
Barkan a Better Point of View
Model
ND400
Type
Operating instructions

This manual is also suitable for

ND400-MAN-ONL-02_1904
Page 2 of 7
A
AA
A
x1
x8
B
BB
B
x8
x20
Z
ZZ
Z4
44
4
x2
x4
No.2+3
=
==
=
M
MM
M4
44
4
x
xx
x4
44
4
M
MM
M6
66
6
x
xx
x4
44
4
M
MM
M8
88
8
3
33
3/
//
/4
44
4"
""
"
/
//
/
2
22
20
00
0
x
xx
x4
44
4
#
##
#
M
MM
M
" / mm
Z
ZZ
Z1
11
1
Z
ZZ
Z2
22
2
Z
ZZ
Z3
33
3
1
11
1"
""
"
/
//
/
2
22
25
55
5
L
LL
L
1
11
1"
""
"
/
//
/
2
22
25
55
5
x5
x1
x2
x1
x3
Z
ZZ
Z5
55
5
Z
ZZ
Z6
66
6
Z
ZZ
Z7
77
7 Z
ZZ
Z8
88
8
Z
ZZ
Z9
99
9
Z
ZZ
Z1
11
10
00
0 Z
ZZ
Z1
11
11
11
1 Z
ZZ
Z1
11
12
22
2
7
5
-
3
9
0
m
m
75 - 390mm
1A
2
M
a
x
6
0
0
m
m
Max 400mm
1
11
1
75 - 390mm
7
5
-
3
9
0
m
m
Max 400mm
M
a
x
6
0
0
m
m
(4 spare)
(1 spare)
(spare)
(spare)
(spare)
Follow the steps according to your TV VESA
(4 connection on the back of the screen)
A
AA
A
T
TT
TV
VV
V
C
CC
CE
EE
EN
NN
NT
TT
TE
EE
ER
RR
R
V
VV
VE
EE
ES
SS
SA
AA
A
C
CC
CE
EE
EN
NN
NT
TT
TE
EE
ER
RR
R
T
TT
TV
VV
V
B
BB
BA
AA
AC
CC
CK
KK
K
33 cm
13"
8cm
3"
Notice: the VESA pattern might NOT be the screen center. The center of part A will be
located on the center of the VESA pattern. Consider the vertical distance between the
center of the VESA pattern and the center of the TV.
Connect parts B to the back of TV, while parts Z5 are below part B.
Choose the screw that fits the VESA holes’ diameter.
For VESA pattern 400X400mm, move the spacer attached
to part B upward as shown.
Z
ZZ
Z1
11
1
Z
ZZ
Z4
44
4
Z
ZZ
Z2
22
2
Z
ZZ
Z3
33
3
Z
ZZ
Z4
44
4
1
11
1A
AA
A
2
B
BB
B
Page 3 of 7
B
BB
B
Z
ZZ
Z5
55
5
3
33
3
V
VV
VE
EE
ES
SS
SA
AA
A
C
CC
CE
EE
EN
NN
NT
TT
TE
EE
ER
RR
R
x 2
2
22
2
5
55
5
4
44
4
Page 4 of 7
A
AA
A
Z
ZZ
Z7
77
7
Z
ZZ
Z4
44
4
Z
ZZ
Z8
88
8
Z
ZZ
Z7
77
7
Z
ZZ
Z9
99
9
Place the arrow anchors Z7 in the finger-
saving tool.Hammer the anchor into the wall.
Place part A on the wall, use a stud finder to make sure the 4 holes
are not on studs. Level part A on the wall using the finger-saving tool.
Mark the 4 holes in part A on the wall with a pencil.
Assemble the wall plate to the wall with
the screw and washer.
Please note that the longer tab of the anchor
is facing up.
7
77
7
6
66
6
Page 5 of 7
Z
ZZ
Z6
66
6
8
88
8
Make sure the nails are hammered all the way in the wall. It's OK if some nails hit the studs
and will not go in all the way.
Hammer the nails to the wall through the holes in part A.
Place the nails parts Z6
in the finger-saving tool.
Page 6 of 7
9
99
9
95lbs / 43kg
1
11
11
11
1
Test the locking mechanism gently.
Connect the TV to part A: hang the top of parts B on the top of part A, push the bottom of
the TV until the bottoms of parts B are hung on the bottom of part A and you hear a click.
TV
1
11
10
00
0
Perform a test by pulling the wall plate downward, not outward.
If the wall plate was pulled out, the installation was not preformed properly.
Please contact our customer service for further instructions.
1
11
12
22
2
In order to disconnect, lift the TV up and
then pull its bottom away from the wall.
Page 7 of 7
To move the screen sideways, lift the screen
slightly and slide it to the wanted side.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7

Barkan a Better Point of View ND400 Operating instructions

Barkan a Better Point of View
Brand
Barkan a Better Point of View
Model
ND400
Type
Operating instructions
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Other documents