MINOURA iH-500-STD / iH-500-OS Instructions Manual

Brand: MINOURA

Model: iH-500-STD / iH-500-OS

Type: Instructions Manual

MINOURA iH-500-STD / iH-500-OS is a versatile smartphone holder designed for cyclists. It securely holds smartphones from 6 to 18mm thick and up to 75mm wide, with or without a case. The adjustable arms and hooks allow for a customized fit to your specific phone, ensuring a stable and secure hold even during rough rides. The quick-release system makes it easy to detach the phone when needed, while the side wings provide additional security to prevent accidental release.

iH-500-STD / iH-500-OS

instructions manual

(ver.1.3 2014/9)

Functions

Holds the phone securely

from all 4 directions.

The arms are fully adjustable.

Side wings can be locked to

prevent unexpected opening

from shock or vibrations

during ride.

The side wings open

wide to accommodate

devices up to 75mm

wide, with or without

a case.

New quick release

system eliminates

worry of theft when

parked. The body is

detachable.

Variations

2 different clamp sizes are available.

●

iH-500-STD : Fits 22 – 29mm diameter

●

iH-500-OS : Fits 27 – 35mm diameter

Neutral

Release

Lock

Back Side

Clamp Release Lever

Bottom Arm

Wing Lock Lever

Top Arm

Clamp Locking Hook

Side Hook

Locking Shim

Clamp Guide

Top Arm Fixing Screw

Bottom Arm

Fixing Srew

Contents

iH-500 Body

Plastic Shim (thin)

Plastic Shim (thick)

3mm Hex Wrench

Stem Mount Bracket

LW Clamp

Mount Bracket

Check to make sure you have all the parts.

Contact place of purchase if you are missing

pieces.

Side Hook (Large) x2

Installation

Directions

Fasten the body to the mount bracket

on the clamp.

Can be adjusted in 90 degree

increments by changing the

insertion direction.

On The Stem

5mm Hex Wrench

Make sure you

securely lock the wing

before start riding.

Adjust Hook

iH-500 comes with 2 sets of Side Hooks

(Large & Small).

Each hook can be set at 2 levels to t various

thickness of the phone.

Choose the best hook size and position to

your actual phone size.

Small Hook / Low

6 – 9mm Thick

9 – 12mm Thick

12 – 15mm Thick

15 – 18mm Thick

Large Hook / Low

Small Hook / High Large Hook / High

Side Hook (Small) Side Hook (Large)

Replace Hook

Side Hook Locking

Shim

Insert the tip of

at screwdriver

and twist

If the hook has been slanted,

the shim cannot be installed.

2 height levels available

Adjust Arms

Adjust the arm position to t the actual

phone size.

Extend both top and

bottom arms.

Place the phone and

shut the wings to hold the

phone temporally.

Slide both arms until they

touch the phone case.

Tighten the screw to x

the position.

We recommend you to

set the phone as close to

you as possible for better

balance.

Clamp Mechanism

iH-500 comes with the lightweight type clamp

which requires a tool to tighten.

Disassemble the clamp, wrap the

handlebar and shut the arms.

Insert the appropriate plastic shim

between the clamp and the handlebar

depending on the target tube diameter.

See the chart below;

[STD] [OS]

--------------------------------------------------

Thick Shim: 22mm / 27mm

Thin Shim: 25mm / 32mm

without Shim: 29mm / 35mm

Insert the roll nut in the all 3 holes.

Make sure the thread hole on the roller

nut can be seen through the hole beside

the clamp body.

Screw the bolt to the thread hole on the

roll nut.

Be sure you must screw the bolt with

your ngers for the rst 3 – 4 revolutions,

then use the 5mm hex wrench to x the

clamp securely.

Thin Shim Thick Shim

Be sure the roll nut is made of

soft alloy material. Do not force

to tighten, otherwise the thread

hole will be broken.

You should not use the hex

wrench from the beginning.

If the bolt has been slanted,

it will destroy the roll nut.

[ Default Combination ]

While pushing the hook fully

toward the wing end, slide down

the shim to the pins to x.

Make sure you fully push down

the shim.

The center chrome plated

screw holds the arm.

Loosen it to adjust the arm

position.

Do not loosen any other

screws.

Open Wings

To open the wings, pull the red

Wing Lock Lever.

After clamping the phone, push down

this lever to lock the wings securely.

Re-pushing the wings after clamping the phone could

release the lock automatically. Make sure the red lock

lever is fully engaged before riding.

Included plastic block is

the bracket for mounting

on the stem.

Tighten the screw with

3mm hex wrench.

You don't use the at

washer.

MINOURA iH-500-STD / iH-500-OS Instructions Manual

MINOURA iH-500-STD / iH-500-OS Instructions Manual

MINOURA iH-500-STD / iH-500-OS Instructions Manual

Related papers

Other documents