Pawleys Island ST1WH Installation guide

Brand: Pawleys Island

Model: ST1WH

Type: Installation guide

Pawleys Island ST1WH is a perfect all-purpose light that also fits neatly into toolboxes and kitchen drawers. Despite its compact size, it produces 500 lumens of bright light with an impressive 8-hour run-time. The ST1WH is powered by the included 18650 rechargeable lithium-ion battery or 3 AAA alkaline batteries. With an IPX4 water-resistant rating and a durable, lightweight aluminum body, the ST1WH is ready for rain and rough handling. Attach it to a keychain, belt loops, or backpack straps with the included removable carabiner.

ASSEMBLY INSTRUCTIONS continue, back of page; Residential Lifetime Warranty, back of page

HARDWARE PACK

TABLE PARTS

ASSEMBLY INSTRUCTIONS

STEP 1. Set one Leg

on a at surface with

the groove near the

middle facing upward,

HOLE

then fit the the end of

one Spreader into the

Leg groove (see FIGURE

) Fit another Leg

onto the top of that

Spreader in the same

manner, making sure that

the holes drilled at one

end of both Legs are

facing the same direction; Legs and Spreader will now form an

"H." (FIGURE 2).

NOTE:

Chair parts are made to connect precisely, so you may find

the fit a little tight during assembly. If so, lightly tap parts into place

with a Rubber Mallet.

SUGGESTED TOOLS (NOT PROVIDED)

• Rubber Mallet

• Standard Phillips Head Screwdriver

• Drill (Square-Head Drill Bit

provided in HARDWARE PACK)

USING BARREL BOLTS

EXTREMELY

IMPORTANT:

Use ONLY

a Standard

Phillips Head

Screwdriver to

tighten Barrel

Bolt Assem-

blies; do NOT

use a drill tted

with a Phillips

head bit, as

you can strip

the Barrel Bolt

head, marring

the appear-

ance of your

Durawood

Essentials

Side Table.

then

To correctly thread Barrel Bolts to Bolt Fasteners: Fit the

Fastener over the bottom of the Bolt, turning the Fastener at

first counterclockwise, until you hear a slight click, which

means the Bolt is in its groove. Now begin tightening clock-

wise as you normally would. NOTE: Holes for bolts may seem

too big, this tolerance will not impact joint, once both barrel

bolt halves are properly secured.

Congratulations on purchasing this Durawood Essentials Side Table! You’re going to love the quality, durability and simple assem-

bly — plus the full Residential Lifetime Warranty. QUESTIONS ABOUT THIS PRODUCT? Call our customer service team, (800) 643-3522.

Before beginning assembly, make sure you have all parts. Note

that not all parts pictured are to scale.

Durawood Essentials

Side Table

GROOVE

4 - 1" Barrel Bolts

4 - Barrel Bolt Fasteners

4 - 2" Flathead Screws

1 - Allen Wrench

1 - Square-Head Drill Bit

Hardware pack

weight: 3.4 oz

Figure 1

Figure 2

STEP 3. Set the Table-

top upside down on

a at surface. Slide

the grooved ends of

one "H" piece over the

tongue pieces cut into

the Tabletop corners

(FIGURE 4), repeat-

ing with the other "H"

piece and remaining

two tongue pieces,

tapping the Legs lightly

with a Rubber Mallet, if

necessary.

STEP 2. Using a

Drill tted with the

Square-Head Drill Bit

provided, screw one

Flathead Screw into

the hole opposite

the Spreader on the

outside of the top

chair Leg from STEP

1, careful not to

overtighten (FIGURE

). Flip the "H" to its

opposite side, using

another Flathead

Screw to attach the

opposite Leg to the

Spreader. Repeat

STEPS 1-2 to connect

the other Spreader

and two remaining

Legs.

GROOVE

STEP 4. Insert Barrel Bolt into a hole near one Tabletop corner

opposite where a Leg connects (FIGURE 5), tapping gently with a

Rubber Mallet, if necessary. Fit the Bolt Fastener over the bottom

of the Barrel Bolt, following the instructions on Using Barrel Bolts

on the other side of this page; hand-tighten only. Repeat this

step with the three remaining Tabletop holes and Barrel Bolt

Assembly.

STEP 5. Using the Allen Wrench and a Standard Phillips Head

Screwdriver, go back and fully tighten the four Barrel Bolt As-

sembly from STEP 4 (FIGURE 6), careful not to over-tighten.

STEP 6 Set your Durawood Essentials Side Table upright —

you're done with assembly, and ready to enjoy it!

HOLE

TONGUE

RESIDENTIAL WARRANTY | This quality product includes a FULL LIFETIME WARRANTY for RESIDENTIAL CUSTOMERS. In the

unlikely event any splintering, rotting, cracking, peeling, chipping, insect infestation or other damage should ever occur, The

Hammock Source will replace this furniture, at no charge to you. Note that an original sales receipt must accompany any

returned product, along with a Return Authorization Number from Hammock Source customer service; call toll-free at

(800) 643-3522.

CONTRACTOR WARRANTY | CONTRACTORS receive a FULL 7-YEAR WARRANTY. Follow the same steps outlined above.

#6008 / 1015

Figure 3

Figure 4

Figure 5

Figure 6

Pawleys Island ST1WH Installation guide

Brand: Pawleys Island

Model: ST1WH

Type: Installation guide

Download PDF

report

Pawleys Island ST1WH Installation guide

Pawleys Island ST1WH Installation guide

Related papers

Other documents