JONATHAN Y JYL2028A Installation guide

Type
Installation guide

JONATHAN Y JYL2028A is a portable lamp with a polarized plug for safety. It requires assembly and comes with all the necessary parts, including a bulb. The lamp has a maximum wattage of 100 watts for incandescent bulbs, 23 watts for CFL bulbs, and 12 watts for LED bulbs. It also comes with a 9-watt LED bulb.

To assemble the lamp, first make sure that all parts are present and undamaged. Then, follow these steps:

  1. Screw the tube (B) onto the base (A).
  2. Screw the tube (C) onto the tube (B).
  3. Screw the parts (D, E, F, G) onto the tube (C).
  4. Insert the harp (H) into the saddle (F).
  5. Put the shade (I) on the harp (H) and tighten the finial (J) into the harp (H).

JONATHAN Y JYL2028A is a portable lamp with a polarized plug for safety. It requires assembly and comes with all the necessary parts, including a bulb. The lamp has a maximum wattage of 100 watts for incandescent bulbs, 23 watts for CFL bulbs, and 12 watts for LED bulbs. It also comes with a 9-watt LED bulb.

To assemble the lamp, first make sure that all parts are present and undamaged. Then, follow these steps:

  1. Screw the tube (B) onto the base (A).
  2. Screw the tube (C) onto the tube (B).
  3. Screw the parts (D, E, F, G) onto the tube (C).
  4. Insert the harp (H) into the saddle (F).
  5. Put the shade (I) on the harp (H) and tighten the finial (J) into the harp (H).
WARNING
WE RECOMMEND INSTALLATION OF THIS LIGHTING FIXTURE BE DONE BY A LICENSED ELECTRICIAN.
WARNING *** SWITCH OFF THE MAIN ELECTRICAL SUPPLY FROM THE MAIN FUSE BOX/CIRCUIT
BREAKER BEFORE INSTALLATION.
INSPECT ITEM CAREFULLY BEFORE ATTEMPTING TO INSTALL IF THERE IS ANY DAMAGE OR
Model# JYL2028A
Product Dimensions: 15"L X 15"W X 59"H
INSPECT
ITEM
CAREFULLY
BEFORE
ATTEMPTING
TO
INSTALL
.
IF
THERE
IS
ANY
DAMAGE
OR
OBVIOUS DEFECT, DO NOT INSTALL. ITEM MAY NOT BE RETURNED ONCE IT HAS BEEN INSTALLED.
CARE AND MAINTENANCE
Unplug lamps before using any cleaning solutions. Dust shades with a feather duster or with an appropriate
vacuum-brush attachment. Wi
p
e with a soft
,
dr
y
cloth and clean lam
p
bases with the methods a
pp
ro
p
riate to
* Please make sure that you have all parts indicated before you begin assembly of this item
*
This item should be assembled on a soft surface to prevent scratching the finish during assembly
vacuum brush
attachment.
Wipe
with
a
soft,
dry
cloth
and
clean
lamp
bases
with
the
methods
appropriate
to
the material. Avoid the use of chemicals and household cleaners as they may damage the finish.
NOTICE& IMPORTANT SAFETY INSTRUCTIONS
*
This
item
should
be
assembled
on
a
soft
surface
to
prevent
scratching
the
finish
during
assembly
* To reduce the risk of fire, electrical shock or injury to persons or property, please follow the guideline below
for safe use and installation
*The external flexible cable or cord of this luminaire cannot be replaced;
If the cord is damaged, the luminaire shall be destroyed
**This portable lamp has a polarized plug (one blade is wider than the other) as a safety feature to reduce
the risk of electric shock. this plug will fit in a polarized outlet only one way. if the plug does not fit fully in
the outlet, reverse the plug, if it still does not fit, contact a qualified electrician. Never use with an extension
cord unless the plug can be fully inserted. do not attempt to defeat this safety feature.
PIECE DESCRIPTION PICTURE QUANTIT
Y
PIECE DESCRIPTION PICTURE QUANTIT
Y
ABCD
Part List and Hardware List
A
.B.C.D
.E.F.G
Lamp base 1X H Harp 1X
E NECK 1X I Shade 1X
F Saddle 1X J Finial 1X
G Socket 1X K Bulb 1X
PREPARATION
Before beginning assembly of product, make sure all parts are present. Compare parts with package contents list and hardware
contents list. If any part is missing or damaged, do not attempt to assemble the product.
E ti t d A bl Ti 6 i t
PLEASE USE ON/OFF TYPE"A" BULB MAX 100-WATT OR CFL BULB MAX 23-WATT OR LED BULB MAX 12-WATT
THERE IS LED 9-WATT BULB IN THE BOX
Estimated Assembly Time: 6 minutes.
Step 1 Step2 Step3
Make sure all parts could be aligned before assemble Insert the Harp (H) into the Saddle (F). Put the light on a level surface to check
Do not rotate lamp body too hard avoid base screw broken Put the shade(I) on the Harp(H), then if everything is stable.
Pull cord through lamp base(A) to tighten stem connections
tighten the Finial (J) into the Harp (H)
P
u
ll
cor
d
th
roug
h
l
amp
b
ase
(A)
t
o
ti
g
ht
en s
t
em connec
ti
ons,
ti
g
ht
en
th
e
Fi
n
i
a
l
(J)
i
n
t
o
th
e
H
arp
(H)
Screw the tube (B) onto the base (A) Insert the bulb(K) into the socket(G).
Screw the tube (C) onto the tube (B)
Screw the part (D,E,F,G) onto the tube(C)
ENJOY YOUR LAMP
  • Page 1 1
  • Page 2 2

JONATHAN Y JYL2028A Installation guide

Type
Installation guide

JONATHAN Y JYL2028A is a portable lamp with a polarized plug for safety. It requires assembly and comes with all the necessary parts, including a bulb. The lamp has a maximum wattage of 100 watts for incandescent bulbs, 23 watts for CFL bulbs, and 12 watts for LED bulbs. It also comes with a 9-watt LED bulb.

To assemble the lamp, first make sure that all parts are present and undamaged. Then, follow these steps:

  1. Screw the tube (B) onto the base (A).
  2. Screw the tube (C) onto the tube (B).
  3. Screw the parts (D, E, F, G) onto the tube (C).
  4. Insert the harp (H) into the saddle (F).
  5. Put the shade (I) on the harp (H) and tighten the finial (J) into the harp (H).

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI