Elvaco CMe2100 Quick Manual

CMe2100 Quick Manual English v4.0 Page | 1

CM e2 100 Qu i ck M an u al

CM e2100

English

Version 4.0

Get the com plete m anual online at ww w.elvaco.com

Page | 2 Support: +46 300 434300 ? support@elvaco.com

Cont ent s

1 DOCUMENT NOTES............................................................................ 3

2 INTRODUCTION .................................................................................. 6

3 MOUNTING ....................................................................................... 10

4 CONFIGURE FOR E-MAIL REPORTS ................................................. 14

5 CONFIGURE FOR FTP REPORTS ....................................................... 17

6 CONFIGURE FOR HTTP REPORTS .................................................... 19

7 CONFIGURE FOR TRANSPARENT M-BUS ........................................ 21

8 RESET TO FACTORY DEFAULT......................................................... 23

9 CHANGING CONFIGURATION .......................................................... 24

10 LED INDICATIONS............................................................................. 33

11 TROUBLESHOOTING ........................................................................ 36

12 REPORT TEMPLATES ........................................................................ 43

13 COMM AND LISTING ......................................................................... 46

14 TECHNICAL SPECIFICATIONS .......................................................... 49

15 SAFETY AND ENVIRONMENT .......................................................... 56

16 ACCESSORIES AND SIMILAR PRODUCTS ....................................... 59

CMe2100 Quick Manual English v4.0 Page | 3

1 Do cum en t no t es

All information in this manual, including product data, diagrams, charts,

etc. represents information on products at the time of publication, and is

subject to change by Elvaco AB without notice. It is recommended that

customers contact Elvaco AB to find out the latest available documentation.

Elvaco AB assumes no responsibility for technical inaccuracies,

typographical errors or any damage, liability, or other losses by use of

this product.

transm itted or reproduced in any form by any m eans without the written perm ission

of Elvaco AB. Printed in Sweden.

Page | 4 Support: +46 300 434300 ? support@elvaco.com

This manual provides information needed to get started with the

CMe2100 product.

CMe2100 version appliance: >= 1.2.0

For a complete description of the CMe2100 product, download the full

manual from Elvaco AB web site, w w w .elv aco.c om .

CMe2100 Quick Manual English v4.0 Page | 5

1.1 Cont act i nf orm at i on

Elv aco A B Headquar t er

Teknikgatan 18

434 37 Kungsbacka

SWEDEN

Phone: +46 300 30250

Fax: +46 300 18440

E-Mail: info@elvaco.com

Elv aco A B Techni cal Support

Phone: +46 300 434300

E-Mail: support@elvaco.com

Online: www.elvaco.com

Page | 6 Support: +46 300 434300 ? support@elvaco.com

2 Int roduct ion

The CMe2100 is a stand-alone, DIN-mounted GSM/GPRS equipment

with M-Bus master, intended to read and store values from any m eter

supporting the M-Bus protocol.

The CMe2100 is available in the following variants:

CMe2100 GPRS M-Bus terminal with M-Bus 2-wire interface and

E-Mail support

CMe2100 Quick Manual English v4.0 Page | 7

2.1 K ey f eat ur es

 Read and store meter data from ABB electricity meters with

IR interface or any slaves supporting the M-Bus standard protocol

 Connect up to 8 M-Bus slaves, extendable using CMeX Series

 Send a variety of meter data reports using E-Mail, FTP, HTTP and SM S

 Transparent M-Bus using TCP and GSM data

 Configurable using SMS ,Telnet and HTTP

 Remotely upgradable application and firmware

 Manufacturer specific report templates

The CMe2100 fits into almost any kind of meter collecting system, i.e.

remote reading for M-Bus compatible electricity meters, water meters,

gas meters, temperature meters, heat meters etc.

Page | 8 Support: +46 300 434300 ? support@elvaco.com

2.2 Over vi ew

1. Serial number

2. Button

3. M-Bus connector

4. Antenna SM A connector

5.

M

-

Bus IR interface

CMe2100 Quick Manual English v4.0 Page | 9

6. GSM LED (Yellow)

7. Error LED (Red)

8. Status LED (Green)

9. SIM card holder

10. Service interface

11. Power supply N

12. Power supply L

Page | 10 Support: +46 300 434300 ? support@elvaco.com

3 M o u n t ing

The CMe2100 should be mounted on a DIN-rail. The metallic clip on the

bottom is used to mount and demount the unit from the DIN-rail. For

safety reasons, a DIN-rail enclosure must cover the terminals.

3.1 SIM car d

Install the GSM SIM card into the SIM card holder (9). Remember the

phone number for later use.

IMPORTANT

 The SIM card shall not have any PIN code activated

 The SIM card must have GPRS internet access activated for full

functionality

 If a prepaid SIM card is used, ensure that enough credits are available

CMe2100 Quick Manual English v4.0 Page | 11

3.2 A nt enna

The antenna should be connected to the SMA connector (4). Depending

on signal strength and environment, a different antenna with extension

cable can be used. Torque should be finger tight.

IMPORTANT

 Do not mount the antenna close to any metallic objects

 Do not mount the antenna close to the M-Bus 2-wire bus

 Do not mount the antenna inside a metallic cabinet

3.3 M -Bus 2-w ire bus

M-Bus is a multi-drop 2-wire bus with no polarity. A cable of either

shielded (typically 4 x 0.8 m m diam./0.5 mm

2

) telephone type or

standard mains type (1.5 mm

2

) should be used. Connect the wiring to

the connector (3). Do not exceed the maximum cable length of 1000 m.

Page | 12 Support: +46 300 434300 ? support@elvaco.com

IMPORTANT

 The internal M-Bus interface can handle up to 8 slaves. Overloading

the bus causes communication problems with the connected slaves.

 All connected slaves must have unique M-Bus secondary addresses.

3.4 IR i nt erf ace w i t h A BB elect ri cit y m et er s or

CM eX Seri es m odul es

When the IR interface will be used beside an ABB electricity meter or

CMeX module, the IR shield (5) should be removed. The CM e2100

should be mounted on the left side of the ABB electricity m eter or CMeX

module. There shall be no space between the CMe2100 and the ABB

electricity meter or CM eX module. (Do not remove the shield if not used

beside an ABB electricity meter or CM eX module.)

CMe2100 Quick Manual English v4.0 Page | 13

3.5 Pow er suppl y

The main supply should be connected to the power supply screw

terminals (11) and (12). Main supply voltage should be in the range of

100-240 VAC, 50/60 Hz. The CM e2100 will be running factory default

settings when first powered up.

An emergency circuit breaker should be used in order to ensure safe

separation of the CMe2100 product from the main power supply.

The next chapters cover the configuration of the CMe2100 product. If any

problem occurs during configuration, please refer to the

Troubleshooting section on page 33.

Page | 14 Support: +46 300 434300 ? support@elvaco.com

4 Co n f igure f o r E-M ail rep o rt s

This section describes how to enable the CMe2100 product to send

E-Mail reports of connected slaves to one or more E-Mail recipients. The

CMe2100 product will store hourly values of connected slaves, send

value reports every day at 00:00 and send an E-Mail installation report

on completion.

4.1 Set E-M ai l r eci pi ent s

SMS to CMe2100 product: qset email <recipients>

Example: qset email name@domain.com,name2@domain.com

The CMe2100 product will acknowledge with an SMS receipt.

CMe2100 Quick Manual English v4.0 Page | 15

4.2 Sear ch and i nst all M -Bus sl aves

The CMe2100 product will search and install M-Bus slaves using primary

and secondary addressing on 2400 baud and synchronize time with an

internet time server.

SMS to CMe2100 product: install <slaves> <profile> <mode>

Par am et er d escr ip t io n:

<slaves> - Number of slaves to find. Not m andatory

<profile> - Configuration profile name. Not mandatory

<mode>- Use word keep to keep existing slaves and clean to

remove all slaves before searching for new.

Page | 16 Support: +46 300 434300 ? support@elvaco.com

Exam pl es:

Install and search for 2 meters and use profile myprofile:

install 2 myprofile

Install and search for 2 meters:

install 2

Clean all existing meters and install and search for 2 meters:

install 2 clean

Keep all existing meters and install and search for 2 n ew meters:

install 2 keep

Install and search for unknown number of m eters:

install

The CMe2100 product is now configured and will by default send E-Mail

value reports of connected slaves every day at 00:00.

CMe2100 Quick Manual English v4.0 Page | 17

5 Co n f igure f o r FTP rep o rt s

This section describes how to enable the CMe2100 product to send FTP

reports of connected slaves to an FTP server. The CMe2100 product will

store hourly values of connected slaves, send value reports every day at

00:00 and send an E-Mail installation report on completion (if E-Mail is

configured, see page 14).

5.1 Set FTP server

SMS to CMe2100 product: qset ftp <server> <port> <user>

Example: qset ftp ftp.domain.com 21 user pass datafolder

The CMe2100 product will acknowledge with an SMS receipt.

Page | 18 Support: +46 300 434300 ? support@elvaco.com

5.2 Sear ch and i nst all M -Bus sl aves

First perform steps as described on page 15.

FTP reports must be manually activated.

Exam pl es:

Activate to send FTP reports every day using report template 2104:

sch report2 1day 2104

Activate to send FTP reports every hour using report template 2104:

sch report2 1hour 2104

Activate to send FTP reports every month using report template 2105:

sch report2 1month 2105

CMe2100 Quick Manual English v4.0 Page | 19

6 Co n f igure f o r HTTP rep o rt s

This section describes how to enable the CMe2100 product to send

HTTP POST reports of connected slaves to a web server. The CMe2100

product will store hourly values of connected slaves, send value reports

every day at 00:00 and send an E-Mail installation report on completion

(if E-Mail is configured, see page 14).

6.1 Set HTTP server

SMS to CMe2100 product: qset http <url> <user> <password>

Example: qset http http://www.domain.com user pass basic

The CMe2100 product will acknowledge with an SMS receipt.

Page | 20 Support: +46 300 434300 ? support@elvaco.com

6.2 Sear ch and i nst all M -Bus sl aves

First perform steps as described on page 15.

HTTP reports must be manually activated.

Exam pl es:

Activate to send HTTP reports every day using report template 3104:

sch report3 1day 3104

Activate to send HTTP reports every hour using report template 3104:

sch report3 1hour 3104

Activate to send HTTP reports every month using report template 3105:

sch report3 1month 3105

Page is loading ...

Elvaco CMe2100 Quick Manual

Elvaco CMe2100 Quick Manual

Related papers

Other documents