Asko D1796FI Planning And Design Manual

Brand: Asko

Model: D1796FI

Type: Planning And Design Manual

This manual is also suitable for

Planning and Design Guide

2002 Vrs 2.0

DISHWASHERS WASHERS DRYERS ACCESSORIES INSTALLATION

ASKO DISHWASHERS

Dimensions & Technical Data

D1706 ..............................................................................2

D1716...............................................................................3

D1776...............................................................................4

D1976...............................................................................5

Changing Standard Front Panels.............................................6

D1796FI and D1996FI.........................................................7

Fitting the D1796FI and D1996FI Custom Door Panel ..............8

D1796FI and D1996FI Custom Panel Installation Options..........9

D1996HNDL.....................................................................10

D1996SS.........................................................................11

Optional Accessories............................................................12

Fully Integrated Fill Strip Installations ................................13

ASKO LAUNDRY

Washers: Dimensions & Technical Data

W6021 ............................................................................15

W6441 ............................................................................16

W6661 ............................................................................17

Dryers: Dimensions & Technical Data

T701 ...............................................................................18

T721 ...............................................................................19

T731 ...............................................................................20

T761 ...............................................................................21

T781 ...............................................................................22

Stacked Pair Installations

W6021/W6441 and T701 .................................................23

W6021/W6441 and T721 .................................................24

W6441 and T731 .............................................................25

W6661 and T761 .............................................................26

W6661 and T781 .............................................................27

Cabinet/Closet Installations

Stacked Installations ...........................................................28

Single Unit Installations........................................................29

Side-by-side Installations.....................................................30

Optional Accessories............................................................31

This planning guide provides unit dimensions, cutout

dimensions, and utility locations only. For more

details, refer to the installation instructions that are

supplied with the unit.

Specifications are subject to change without notice. See installation instructions for additional details.

The electrical and water supplies should

enter through the area indicated by the

shaded area. Preferably, they should come

through the right side of the machine. The

access hole must be round and smooth

and no bigger than 2" in diameter.

TECHNICAL DATA

Electricity 120V, 60Hz, 15 amp

Water pressure 18-176 psi

Heating element 1400 watt

Max loading 1600 watt

ASKO DISHWASHER

FRONT PANELS

The front panels on Model D1706 (except

the stainless steel model) can be covered

or replaced with wood panels. See page 6

for instructions on how to change the front

panels.

CUTOUT DIMENSIONS

US Metric

Height 32-1/4"–35-1/2" 819–902 mm

Width 24" 610 mm

Depth 23-7/16" 596 mm

*This depth allows a 1" (25 mm) space for

the high-loop drain hose.

NOTE: Maintain a 1/8" (3 mm) minimum

clearance between unit and cabinet.

EASYINSTALL SYSTEM

Every ASKO dishwasher comes with the

unique EasyInstall System that speeds the

installation and reduces problems. This

system has these components which are

approved by regulatory authorities (cUL):

• Over 5' of Pex hose that replaces the

water-inlet copper tubing. It has a 3/8"-

compression fitting that mates with the

shut-off valve.

• Over 6' of drainhose with an adaptable

drain connection.The high loop is built

into this hose on the back of the unit. If

this loop is removed to lengthen the

hose, another high-loop must be built

into the installation somewhere along

the line (typically where the hose passes

through the cabinet).

• A 6' long electrical cord with standard,

3-pronged, 110V plug. This eliminates

the need to wire anything under the unit.

24"

610 mm

23-7/16"

596 m

32-1/4" to 35-1/2"

819 to 902 mm

50mm

6-1/4" to 8-1/4"

159-210 mm

35-1/2"

902 mm

24"

610 mm

46-1/2"*

UNIT DIMENSIONS

US Metric

Height 32-1/4"–35-1/2" 819–902 mm

Width 24" 610 mm

Depth 23-7/16"* 596 mm

Depth w/door open 46-1/2"* 1181 mm

Weight 104 lb 48 kg

MODEL D1706

Specifications are subject to change without notice. See installation instructions for additional details.

ASKO DISHWASHER

MODEL D1716

The electrical and water supplies should

enter through the area indicated by the

shaded area. Preferably, they should come

through the right side of the machine. The

access hole must be round and smooth

and no bigger than 2" in diameter.

TECHNICAL DATA

Electricity 120V, 60Hz, 15 amp

Water pressure 18-176 psi

Heating element 1400 watt

Max loading 1600 watt

FRONT PANELS

The front panels on Model D1716 (except

the stainless steel model) can be covered

or replaced with wood panels. See page 6

for instructions on how to change the front

panels.

CUTOUT DIMENSIONS

US Metric

Height 32-1/4"–35-1/2" 819–902 mm

Width 24" 610 mm

Depth 23-7/16" 596 mm

*This depth allows a 1" (25 mm) space for

the high-loop drain hose.

NOTE: Maintain a 1/8" (3 mm) minimum

clearance between unit and cabinet.

EASYINSTALL SYSTEM

Every ASKO dishwasher comes with the

unique EasyInstall System that speeds the

installation and reduces problems. This

system has these components which are

approved by regulatory authorities (cUL):

• Over 5' of Pex hose that replaces the

water-inlet copper tubing. It has a 3/8"-

compression fitting that mates with the

shut-off valve.

• Over 6' of drainhose with an adaptable

drain connection.The high loop is built

into this hose on the back of the unit. If

this loop is removed to lengthen the

hose, another high-loop must be built

into the installation somewhere along

the line (typically where the hose passes

through the cabinet).

• A 6' long electrical cord with standard,

3-pronged, 110V plug. This eliminates

the need to wire anything under the unit.

24"

610 mm

23-7/16"

596 m

32-1/4" to 35-1/2"

819 to 902 mm

50mm

6-1/4" to 8-1/4"

159-210 mm

35-1/2"

902 mm

24"

610 mm

46-1/2"*

UNIT DIMENSIONS

US Metric

Height 32-1/4"–35-1/2" 819–902 mm

Width 24" 610 mm

Depth 23-7/16"* 596 mm

Depth w/door open 46-1/2”* 1181 mm

Weight 104 lb 48 kg

Specifications are subject to change without notice. See installation instructions for additional details.

MODEL D1776

The electrical and water supplies should

enter through the area indicated by the

shaded area. Preferably, they should come

through the right side of the machine. The

access hole must be round and smooth

and no bigger than 2" in diameter.

TECHNICAL DATA

Electricity 120V, 60Hz, 15 amp

Water pressure 18-176 psi

Heating element 1400 watt

Max loading 1600 watt

ASKO DISHWASHER

FRONT PANELS

The front panels on Model D1776 (except

the stainless steel model) can be covered

or replaced with wood panels. See page 6

for instructions on how to change the front

panels.

CUTOUT DIMENSIONS

US Metric

Height 32-1/4"–35-1/2" 819–902 mm

Width 24" 610 mm

Depth 23-7/16" 596 mm

*This depth allows a 1" (25 mm) space for

the high-loop drain hose.

NOTE: Maintain a 1/8" (3 mm) minimum

clearance between unit and cabinet.

EASYINSTALL SYSTEM

Every ASKO dishwasher comes with the

unique EasyInstall System that speeds the

installation and reduces problems. This

system has these components which are

approved by regulatory authorities (cUL):

• Over 5' of Pex hose that replaces the

water-inlet copper tubing. It has a 3/8"-

compression fitting that mates with the

shut-off valve.

• Over 6' of drainhose with an adaptable

drain connection.The high loop is built

into this hose on the back of the unit. If

this loop is removed to lengthen the

hose, another high-loop must be built

into the installation somewhere along

the line (typically where the hose passes

through the cabinet).

• A 6' long electrical cord with standard,

3-pronged, 110V plug. This eliminates

the need to wire anything under the unit.

24"

610 mm

23-7/16"

596 m

32-1/4" to 35-1/2"

819 to 902 mm

50mm

6-1/4" to 8-1/4"

159-210 mm

35-1/2"

902 mm

24"

610 mm

46-1/2"*

UNIT DIMENSIONS

US Metric

Height 32-1/4"–35-1/2" 819–902 mm

Width 24" 610 mm

Depth 23-7/16"* 596 mm

Depth w/door open 46-1/2"* 1181 mm

Weight 104 lb 48 kg

Specifications are subject to change without notice. See installation instructions for additional details.

MODEL D1976

The electrical and water supplies should

enter through the area indicated by the

shaded area. Preferably, they should come

through the right side of the machine. The

access hole must be round and smooth

and no bigger than 2" in diameter.

TECHNICAL DATA

Electricity 120V, 60Hz, 15 amp

Water pressure 18-176 psi

Heating element 1400 watt

Max loading 1600 watt

ASKO DISHWASHER

FRONT PANELS

The front panels on Model D1976 (except

the stainless steel model) can be covered

or replaced with wood panels. See page 6

for instructions on how to change the front

panels.

CUTOUT DIMENSIONS

US Metric

Height 32-1/4"–35-1/2" 819–902 mm

Width 24" 610 mm

Depth 23-7/16" 596 mm

*This depth allows a 1" (25 mm) space for

the high-loop drain hose.

NOTE: Maintain a 1/8" (3 mm) minimum

clearance between unit and cabinet.

EASYINSTALL SYSTEM

Every ASKO dishwasher comes with the

unique EasyInstall System that speeds the

installation and reduces problems. This

system has these components which are

approved by regulatory authorities (cUL):

• Over 5' of Pex hose that replaces the

water-inlet copper tubing. It has a 3/8"-

compression fitting that mates with the

shut-off valve.

• Over 6' of drainhose with an adaptable

drain connection.The high loop is built

into this hose on the back of the unit. If

this loop is removed to lengthen the

hose, another high-loop must be built

into the installation somewhere along

the line (typically where the hose passes

through the cabinet).

• A 6' long electrical cord with standard,

3-pronged, 110V plug. This eliminates

the need to wire anything under the unit.

24"

610 mm

23-7/16"

596 m

32-1/4" to 35-1/2"

819 to 902 mm

50mm

6-1/4" to 8-1/4"

159-210 mm

35-1/2"

902 mm

24"

610 mm

46-1/2"*

UNIT DIMENSIONS

US Metric

Height 32-1/4"–35-1/2" 819–902 mm

Width 24" 610 mm

Depth 23-7/16"* 596 mm

Depth w/door open 46-1/2"* 1181 mm

Weight 104 lb 48 kg

Specifications are subject to change without notice. See installation instructions for additional details.

1/4" PANEL TRIM KIT

CHANGING THE STANDARD FRONT PANELS

The front panels on Models D1706, D1716, D1776 and D1976

(except the stainless steel models) can be replaced with wood

panels.

PANEL DIMENSIONS

For standard, non-raised panels, use 1/16" to 1/4" material. For

custom raised panels, the decor trim will accept up to 1/4" flange.

The raised panel can be mounted on a backing sheet cut to fit as

shown on the right.

NOTE: The stainless steel panels do not have holes for custom

trim. You have to drill the holes.

INSTALLING THE PANEL

WARNING! Before working on any electrical appliance,

be sure the electrical power has been turned off at the

breaker/fuse box.

Refer to the illustration at bottom right for instruction references.

1. Remove the lower access panel with standard or 20 torx

screwdriver.

2. Carefully remove the plastic plugs around the edges of the

access panel and upper door panel. You may discard the

plugs.

3. Using the screws provided with the trim kit, loosely secure

parts A and C to the upper door panel.

4. Slide the upper panel into the trim kit grooves.

5. Tighten the screws holding parts A and C.

6. Secure part B and tighten screws.

7. Loosely screw part E to the lower access panel.

8. Slide the custom panel into trim kit channels and tighten the

screw to part E.

9. Secure part D of the trim kit and tighten the screws.

10. Secure the lower access panel to the dishwasher.

11. Drop the lower access panel to line up with the lower holes

on the guard plate and secure the screws. (Make sure the

exhaust vent is below the panel. Otherwise, steam from the

vent could eventually damage the panel.)

12. Before you push the dishwasher into the cabinet opening,

test the door to make sure it opens properly, (The door is

counter-balanced, so it should remain in any position.) If it

doesn’t, you may need to adjust the door springs (see page 8).

13. Fasten the dishwasher to the cabinet.

Trim kit part numbers:

White: 8070850-0

Black: 8070850-29

ASKO DISHWASHER

Upper Panel

21-3/16"

538 mm

23-3/16"

589 mm

25 mm

21-3/16"

538 mm

2-1/4"

57 mm

17-15/16"

456 mm

25 mm

Lower Panel

25 mm

21-3/16"

538 mm

23-3/16"

589 mm

25 mm

2-3/16"

56 mm

4-3/16"

106 mm

25 mm

Raised area

Specifications are subject to change without notice. See installation instructions for additional details.

MODEL D1796FI AND D1996FI

The electrical and water supplies should

enter through the area indicated by the

shaded area. Preferably, they should come

through the right side of the machine. The

access hole must be round and smooth

and no bigger than 2" in diameter.

TECHNICAL DATA

Electricity 120V, 60Hz, 15 amp

Water pressure 18-176 psi

Heating element 1400 watt

Max loading 1600 watt

ASKO DISHWASHER

CUSTOM FRONT PANELS

The D1796FI and D1996FI can only be

installed with a fully-integrated custom

door panel that extends from the toe kick to

the counter top. A one-piece custom door

panel with a curved handle is available for

4-inch toe kick installations (see page 12).

Refer to page 8 for instructions on how to

install the custom panels.

CUTOUT DIMENSIONS

US Metric

Height 32-1/4"–35-1/2" 819–902 mm

Width 23-3/4" 603 mm

Depth 23-7/16" 596 mm

*For fully-integrated installations, the

dishwasher’s total depth with the door open

can vary depending on the height of the toe

kick. The total depth for a 4" toe kick is

48-1/4", a 6" toe kick is 46-1/2". This

depth varies from the standard 46-1/2"

because in a 4" toe kick installation the

door panel is typically extended 1-3/4"

beyond the door (control panel) and this

lengthens the door. See page 9 for details.

NOTE: Maintain a 1/8" (3 mm) minimum

clearance between unit and cabinet.

EASYINSTALL SYSTEM

Every ASKO dishwasher comes with the

unique EasyInstall System that speeds the

installation and reduces problems. This

system has these components which are

approved by regulatory authorities (cUL):

• Over 5' of Pex hose that replaces the

water-inlet copper tubing. It has a 3/8"-

compression fitting that mates with the

shut-off valve.

• Over 6' of drainhose with an adaptable

drain connection.The high loop is built

into this hose on the back of the unit. If

this loop is removed to lengthen the

hose, another high-loop must be built

into the installation somewhere along

the line (typically where the hose passes

through the cabinet).

• A 6' long electrical cord with standard,

3-pronged, 110V plug. This eliminates

the need to wire anything under the unit.

23-3/4"

603 mm

23-7/16"

596 m

32-1/4" to 35-1/2"

819 to 902 mm

50mm

6-1/4" to 8-1/4"

159-210 mm

23-1/2"

603 mm

46-1/2" - 48-1/4"*

1181 - 1226 mm

32-1/4" - 35-1/2"

819 - 902 mm

UNIT DIMENSIONS

US Metric

Height 32-1/4"– 35-1/2" 819–902 mm

Width 23-1/2" 597 mm

Depth 23-7/16" 596 mm

Depth w/door open 46-1/2"– 48-1/4”* 1181–1226 mm

Weight 104 lb 48 kg

Specifications are subject to change without notice. See installation instructions for additional details.

The D1796FI and D1996FI can only be installed with a fully-

integrated custom door panel that extends from the toe kick to

the counter top. The unit comes with everything needed to make

installing the door panel easy. The door is predrilled for the

panel’s mounting screws.

The custom panel should be a minimum of 3/4" (19 mm) thick.

ITEMS PROVIDED WITH THE UNIT

• Two 3/8" screws

• Four 1-3/4" screws

• Four adhesive-backed plastic spacer washers

ADJUSTING THE DOOR SPRINGS

Before you push the dishwasher into the cabinet opening, test the

door to make sure it stays in place at any angle. If it tends to fall

down, pull out the machine and tension the door

springs on the sides of the machine by moving

them one hole farther back or by twisting the

spring to make it shorter.

CUSTOM PANEL DIMENSIONS

Width: 23-1/2" (597 mm)

Height: 28-1/8"–30-1/8" (714 mm–765 mm)

(Measured from the top of the panel to the lower

edge of the kitchen cabinet.)

Thickness: Minimum 3/4" (19 mm)

Weight: Up to 22 lb.

INSTALLING THE CUSTOM PANEL

Before fitting the custom panel, the dishwasher must be installed

underneath the cabinet. After you’ve made the required

measurements, pull the machine out again to install the panel.

Refer to the illustration at right for instruction references.

1. Fit the handle (A) onto the panel according to the manufact-

urer’s instructions. (NOTE: A handle should be used rather

than a knob, because a knob does not provide enough grip.)

2. Remove the adhesive protection from the washers and place

them in line with the four keyholes (C) on the metal front of

the dishwasher door.

3. Loosen the screws (D) on the outer edges of the dishwasher

door.

4. Pull the turbo fan exhaust frame (E) down until the lower edge

aligns with the lower edge of the cabinets and tighten the

screws. Snap the plastic duct into the turbo fan exhaust vent.

WARNING! The custom panel must not

obstruct the fan exhaust vent; otherwise,

steam from the vent could eventually

damage the cabinet.

5. The two short screws (B) go into the back of the panel, 16-

3/16" (411 mm) from the upper edge of the panel and 5/8"

from the outer edges. Insert the short screws into the panel,

leaving 1/8" (3 mm) of space between the screw head and

the panel.

6. Hook the panel screws (F) into the keyholes (C) on the

dishwasher door.

7. Push the panel upwards until the lower edge aligns with the

lower edge of the cabinets and secure the screws.

WARNING! The custom panel should not extend more

than 2-15/16" (75 mm) below the bottom of the dish-

washer door; otherwise, it will strike the toe kick and

damage the machine and/or the panel.

FITTING THE D1796FI AND D1996FI CUSTOM DOOR PANEL

Shorten

8.Open the door and tighten the screws (F) inside.

ASKO DISHWASHER

Specifications are subject to change without notice. See installation instructions for additional details.

ASKO DISHWASHER

4-INCH TOE KICK INSTALLATIONS

Custom panels the same height as the

dishwasher door

If the custom panel is the same height as the dishwasher door, a 2"

decorative fill strip or pull-out cutting board must be used to fill the

area between the panel and the counter top (as illustrated below).

If you install the door panel to reach the cabinet top, we

recommend that you install a 2" support strip between the upper

edge of the dishwasher and the counter to hide the top of the

dishwasher and further reduce water noise. A metal fill strip is

also available for this type of installation (see page 12).

With a 4-inch toe kick installation, the

door panel extends 2 inches above the

control panel, as illustrated.

Custom panels that extend to cabinet top

Another installation option for a 4" toe kick is to extend the

custom panel to the cabinet top (as illustrated below), which

eliminates the need for a decorative fill strip. A one-piece custom

door panel with a curved handle is available for 4-inch toe kick

installations (see page 12).

6-INCH TOE KICK INSTALLATIONS

For 6" toe kick installations, no decorative fill strips or support

strips are necessary.

D1796FI AND D1996FI CUSTOM PANEL INSTALLATION OPTIONS

1-3/4"

(44 mm)

23-1/2"

597 mm

2" decorative fill strip or cutting board

28-1/8"

714 mm

4-inch toe kick

2-inch support strip

NOTE: If the cutout is 24" wide, the custom panel can be

23-3/4" wide.

Panel extends from toe kick to cabinet top.

23-1/2"

597 mm

Panel extends from toe kick to cabinet top.

30-1/8"

765 mm

4-inch toe kick

Specifications are subject to change without notice. See installation instructions for additional details.

MODEL D1996HNDL

The electrical and water supplies should

enter through the area indicated by the

shaded area. Preferably, they should come

through the right side of the machine. The

access hole must be round and smooth

and no bigger than 2" in diameter.

TECHNICAL DATA

Electricity 120V, 60Hz, 15 amp

Water pressure 18-176 psi

Heating element 1400 watt

Max loading 1600 watt

ASKO DISHWASHER

FRONT PANELS

Model D1996HNDL is not designed to

accept a custom front panel. Even though

the controls are on top of the door, this

model installs like a standard ASKO

dishwasher. It fits in American cabinets

(4" toe kick) with a 24" wide opening.

CUTOUT DIMENSIONS

US Metric

Height 32-1/4"–35-1/2" 819–902 mm

Width 24" 610 mm

Depth* 23-7/16" 596 mm

*This depth allows a 1" (25 mm) space for

the high-loop drain hose.

NOTE: Maintain a 1/8" (3 mm) minimum

clearance between unit and cabinet.

EASYINSTALL SYSTEM

Every ASKO dishwasher comes with the

unique EasyInstall System that speeds the

installation and reduces problems. This

system has these components which are

approved by regulatory authorities (cUL):

• Over 5' of Pex hose that replaces the

water-inlet copper tubing. It has a 3/8"-

compression fitting that mates with the

shut-off valve.

• Over 6' of drainhose with an adaptable

drain connection.The high loop is built

into this hose on the back of the unit. If

this loop is removed to lengthen the

hose, another high-loop must be built

into the installation somewhere along

the line (typically where the hose passes

through the cabinet).

• A 6' long electrical cord with standard,

3-pronged, 110V plug. This eliminates

the need to wire anything under the unit.

24"

610 mm

23-7/16"

596 m

32-1/4" to 35-1/2"

819 to 902 mm

50mm

6-1/4" to 8-1/4"

159-210 mm

46-1/2"*

32-1/4" - 35-1/2"

819 - 902 mm

UNIT DIMENSIONS

US Metric

Height 32-1/4"–35-1/2" 819–902 mm

Width 24" 610 mm

Depth 23-7/16"* 596 mm

Depth w/door open 46-1/2"* 1181 mm

Weight 104 lb 48 kg

Specifications are subject to change without notice. See installation instructions for additional details.

ASKO DISHWASHER

MODEL D1996SS

The electrical and water supplies should

enter through the area indicated by the

shaded area. Preferably, they should come

through the right side of the machine. The

access hole must be round and smooth

and no bigger than 2" in diameter.

TECHNICAL DATA

Electricity 120V, 60Hz, 15 amp

Water pressure 18-176 psi

Heating element 1400 watt

Max loading 1600 watt

FRONT PANELS

Model D1996SS is not designed to accept

a custom front panel. Even though the

controls are on top of the door, this model

installs like a standard ASKO dishwasher. It

fits in American cabinets (4" toe kick) with

a 24" wide opening.

CUTOUT DIMENSIONS

US Metric

Height 32-1/4"–35-1/2" 819–902 mm

Width 24" 610 mm

Depth* 23-7/16" 596 mm

*This depth allows a 1" (25 mm) space for

the high-loop drain hose.

NOTE: Maintain a 1/8" (3 mm) minimum

clearance between unit and cabinet.

EASYINSTALL SYSTEM

Every ASKO dishwasher comes with the

unique EasyInstall System that speeds the

installation and reduces problems. This

system has these components which are

approved by regulatory authorities (cUL):

• Over 5' of Pex hose that replaces the

water-inlet copper tubing. It has a 3/8"-

compression fitting that mates with the

shut-off valve.

• Over 6' of drainhose with an adaptable

drain connection.The high loop is built

into this hose on the back of the unit. If

this loop is removed to lengthen the

hose, another high-loop must be built

into the installation somewhere along

the line (typically where the hose passes

through the cabinet).

• A 6' long electrical cord with standard,

3-pronged, 110V plug. This eliminates

the need to wire anything under the unit.

24"

610 mm

23-7/16"

596 m

32-1/4" to 35-1/2"

819 to 902 mm

50mm

6-1/4" to 8-1/4"

159-210 mm

46-1/2"*

1181 mm

32-1/4" - 35-1/2"

819 - 902 mm

UNIT DIMENSIONS

US Metric

Height 32-1/4"–35-1/2" 819–902 mm

Width 24" 610 mm

Depth 23-7/16"* 596 mm

Depth w/door open 46-1/2"* 1181 mm

Weight 104 lb 48 kg

Curved Handle for Fully Integrated Dishwashers

8073718-0 White 8073718-29 Black

8073718-84 Bisque 8073718-82 Brass-Like 8073718-95 Stainless Steel

Metal Top Fill Strip

Attaches to top of FI units and fills gap between tank and counter top.

8073869-95

FI Side Fill Strips, Stainless Steel

Fills gap when FI unit installed in 24" wide opening. Kit includes both left- and right-side strips.

8075045-95

One-Piece Door with Handle

Only available for D1796FI and D1996FI

One-piece door with matching one-piece, curved handle.

These doors cannot be used in ADA (<34") installations.

8072856–0 White 8072856–84 Bisque

8072856–29 Black 8072856–95 Stainless Steel

1/4" Trim Kits

Models D1706, D1716, D1776 and D1976

8070850–0 White trim kit for installing 1/4" custom panels

8070850–29 Black trim kit for same installation and units as above

European Toe Kick (Two Pieces)

8070121-0 Extension 8057528–0 Toe Kick

White European toe kick to accommodate 6" toe space on models

D1796FI and D1996FI. Two pieces are 23-1/2" wide.

8070121-29 Extension 8057528–29 Toe Kick

Black toe kick for same installation. Two pieces are 23-1/2" wide.

2.5" Toe Kicks

805SC-W White 805SC-B Black 805SC-SS Stainless Steel

Dishwasher Tip Guard

8070851

Secures dishwasher when it’s not possible to attach it to cabinetry or counter top

Two Heavy-Duty Door Springs

• 7-12 lbs.: 8060232-77 (Yellow)

• 12-22 lbs: 8071323-77 (Red) (Standard on all FI dishwashers)

Provide additional support for custom panels

Replacement Dishwasher Baskets

8801200–36 8801199–36

Lower basket for all models; has removable tines Upper basket for all models; has a split cup rack and

a stemware rack

Specifications are subject to change without notice. See installation instructions for additional details.

OPTIONAL DISHWASHER ACCESSORIES

ASKO DISHWASHER

European

Toe Kick

Extension

2.5" Toe Kick

Figure 1.

Figure 2.

Figure 3.

Figure 4.

Specifications are subject to change without notice. See installation instructions for additional details.

FILL STRIPS INSTALLATION INSTRUCTIONS

ASKO DISHWASHER

INSTALLATION INSTRUCTIONS

Attaching Top Fill Strip

1. If you are installing the dishwasher with either the top fill strip or side fill strips, you must

remove the insulation strips. These are the black sponge strips attached to the front edge of

the tank, from top to bottom. To remove them, simply grip the top or bottom edge and pull it

away from the tank, as illustrated in Figure 1.

2. If you are installing the top fill strip, you must remove the black rubber strip attached to the

flange of the tank. Simply grip one end of the rubber strip and pull it away from the flange,

as illustrated in Figure 2.

3. Remove the fill strip and two mounting screws from the package.

4. The top fill strip has a slot that runs from side to side. This slot faces the front of the

dishwasher. Set the fill strip on top of the dishwasher where you removed the insulation and

rubber strip.

5. Slide the strip forward, having the flange of the dishwasher and the top mounting brackets

slide through the slot on the front of the trim strip until the strip is flush with the dishwasher

tank, as illustrated in Figures 3 and 4. (If it does not pull forward far enough to be flush, it

will not secure to the dishwasher.)

6. Open the dishwasher door and insert the mounting screws as if you were going to mount

the dishwasher to the cabinet, as illustrated in Figure 5.

AVAILABLE ACCESSORIES

ASKO offers accessories for the fully integrated (FI) dishwasher to give installations in American cabinetry a clean and complete look.

The available accessories are:

Top Fill Strip Side Fill Strip One-Piece Door Panels

Fills the gap between the dishwasher and

the bottom of the countertop.

8073869-95

Fills the gap between the side of

the dishwasher and the cabinet.

8074248-95 Right

8074249-95 Left

Available in white, black, bisque

and stainless steel. We also offer

a brass-like handle.

Figure 5.

Specifications are subject to change without notice. See installation instructions for additional details.

ASKO DISHWASHER

Attaching Side Fill Strips

1. If you are installing the dishwasher with the side fill strips, you must remove the

insulation strips. These are the black sponge strips attached to the front edge of the

tank, from top to bottom. To remove them, simply grip the top or bottom edge and pull

it away from the tank, as illustrated in Figure 6.

2. The trim strip has multiple mounting holes. Align the largest hole with the same size

hole on the side of the dishwasher, as illustrated in Figure 7. (This hole is used when

you anchor the dishwasher to the cabinet.)

3. Keeping the trim strip aligned with the holes, open the dishwasher door and secure it

to the dishwasher with the screws provided, as illustrated in Figure 8. (The screw head

should be inside the tank.)

4. When anchoring the dishwasher to the cabinet, height adjustments is essential to

properly align the panel with the cabinet facings.

NOTES:

Be sure to order a side fill strip for each side (left and right).

The unit will accept various sized panels. Refer to the dishwasher specifications before

building the panel so it will correctly align with the cabinet facings.

If a four-inch toe kick is used, the unit must be installed at its lowest height. (The

dishwasher is delivered at its lowest height.) On four-inch toe kick installations, the

one-piece door panel will extend past the top of the control panel approximately 1-3/4".

Figure 6.

Figure 8.

FILL STRIPS INSTALLATION INSTRUCTIONS

Figure 7.

ASKO Inc. • P.O. Box 851805 • Richardson, Texas 75085-1805 • Advisory Center: 800-898-1879

Underwriters Laboratories, Inc.

Printed on Recycled Paper

ASKO Inc. retains the right to vary the model specifications at any time. All facts were accurate at time of printing. Before purchasing any ASKO product, read important energy cost and efficiency information available from retailer.

BUILT TO LAST LONGER

www.askousa.com

THE AWARDS JUST KEEP STACKING UP.

0F HOUSEHOLDS

SAY ASKO IS QUIETEST.

Dishwashers selected by 91%

of homeowners as the quietest

in independent tests.

D1996FI Dishwasher

W660 Washer & T760 Dryer

W660 and T760 for 2000 W600 for 2001

W6661 Washer & T761 Dryer

2002

W660 Washer & T760 Dryer

2000

★

ASKO dishwashers and washers

meet the Energy Star

requirements.

All ASKO products are covered

by the Good Housekeeping Seal.

1805 Dishwasher

Excellence In

Design Innovation

Asko D1796FI Planning And Design Manual

Brand: Asko

Model: D1796FI

Type: Planning And Design Manual

This manual is also suitable for

Download PDF

report

Asko D1796FI Planning And Design Manual

This manual is also suitable for

Asko D1796FI Planning And Design Manual

Related papers

Other documents