© Öhlins Racing AB. All rights reserved. Any re-
printing or unauthorized use without the written
permission of Öhlins Racing AB is prohibited.
Printed in Sweden.
Mounting Instructions HO793_1 Issued 2007-05-21.
These instructions and other documents
can be downloaded from www.ohlins.com
Mounting Instructions
SHOCK ABSORBER HO793
for Honda CRF 250 2007
Read the Öhlins Owner’s Manual before installing this product
In
s
t
a
lling
a
sh
o
c
k
a
b
s
o
rb
e
r
t
h
a
t
is
n
ot
a
pp
r
ov
e
d
b
y
th
e
ve
h
ic
le
m
a
n
u
fa
c
tu
r
er
m
ay
a
f
f
ec
t
th
e
s
tab
il
ity
o
f
y
o
ur
v
e
h
ic
le
.
I
n
s
t
a
ll
in
g
a
sh
o
c
k
a
b
s
o
rb
e
r
t
h
a
t
is n
ot
a
p
p
r
o
v
e
d
b
y
t
h
e
v
e
h
i
cl
e
m
an
u
fact
u
r
e
r
m
ay
a
f
fe
c
t th
e
sta
b
il
i
ty
o
f
y
o
u
r
v
e
h
ic
le
.
In
s
t
a
l
lin
g
a
s
ho
c
k
a
bs
orb
er
t
h
at
is
n
ot
a
p
p
r
o
ve
d
b
y
th
e
v
e
h
ic
le
m
a
n
u
f
a
c
tu
r
er
m
a
y
a
f
f
ec
t t
h
e
st
a
b
i
l
ity
o
f
y
ou
r v
e
h
icl
e.
Ins
ta
ll
in
g
a
s
h
o
ck
a
b
s
o
r
b
e
r
t
h
a
t is
n
o
t
a
pp
r
o
ve
d
b
y
t
h
e
ve
h
ic
l
e m
a
n
u
fa
ct
ure
r
m
a
y
a
f
fe
c
t th
e
sta
b
il
ity
o
f
y
o
u
r v
e
h
ic
le
.
Öhlins Racing AB, Box 722, S-194 27 Upplands Väsby, Sweden.
Phone +46 8 590 025 00 Fax +46 8 590 025 80
www.ohlins.com
WITH SET-UP DATA
Kit Contents:
Part no. Pcs.
Shock absorber HO793 1
Spring clip 00629-05 1
Spring clip 00629-07 1
C-spanner single 00710-02 1
Öhlins Sticker 00197-01 2
Memo Notes Sticker 01180-01 1
Öhlins Owner’s Manual 1
Before installing this product, check the con-
tents of the kit listed below. If anything is
missing, please contact your nearest Öhlins
dealer.
During storage and transportation, especially
at high ambient temperature, some of the oil
and grease used for assembling may leak and
stain the packaging. This is in no way detri-
mental to the product, wipe off the excessive
oil/grease with a cloth.
NOTE!
No spring included in this kit. See the
Spring Guide in this folder, or contact an
Öhlins dealer for advice.
ADJUSTMENTS
Spring preload
Loosen the screw of the spring platform
clamp. Use the C-spanner provided in
this kit, turn the spring platform to the
desired position. Or, when installed on
the vehicle, turn the spring. Tighten the
screw of the spring platform clamp.
Compression damping
Adjust on top of the reservoir.
Low speed: Turn the slotted centre screw
High speed: Turn the hexagon screw
Turn clockwise to increase damping, turn
counter clockwise to decrease.
Rebound damping
Turn the wheel on the piston shaft above
the end eye/bracket. Turn clockwise to
increase damping, turn counter clock-
wise to decrease.
Set-up data
Spring preload 6 turns (10 mm)
Rebound damping 18 clicks
Compression damping
Low speed 15 clicks
High speed 1.5 turns
Free sag and Ride height
Free sag, rear 30±5 mm
Free sag, front 30±5 mm
Ride height, rear 100-105 mm
Ride height, front 80±5 mm
Shock absorber data
Length 498 mm
Stroke 133 mm
A
B
Spring preload is the difference
between A and B;
A Free spring length
B Installed spring length
A-B = Spring preload
preload
1
2
3
1
2
3
WARNING!
When delivered, the Öhlins shock absorber is
dialed to the recommended settings for the spe-
cifi c brand and make of the motorcycle. Before
riding, always ensure that the basic settings
made by Öhlins are intact.
To set the adjuster:
The turn adjusters have a normal right hand
thread. Turn the damping adjusters clock-
wise to fully closed (position zero [0]). Then,
turn counter clockwise to open, and count
the clicks until you reach the recommended
number of clicks. See Set-up data.
Do not use force, delicate sealing surfaces can
be damaged. Handtighten only.
Loosen the screw
...and adjust with
a C-spanner
... by turning the spring
or
INSTALL THE SHOCK ABSORBER
WARNING!
It is advisable to have an Öhlins dealer install the
shock absorber.
1
Raise the rear end of the vehicle so that the
rear wheel barely touches the ground.
WARNING!
Make sure the vehicle is securely supported so
that it will not tip.
WARNING!
Make sure that all screws are tightened to the
correct torque and that nothing fouls or restricts
movement of the shock absorber when the sus-
pension is fully compressed or extended.
2
Remove the seat.
3
Remove the number plate. Loosen the silencer
from the sub frame, leave it attached to the
exhaust pipe.
1
INSTALL THE SPRING
NOTE!
Install the spring to the shock absorber before
installing the shock absorber on the vehicle.
1
Measure the free length of the spring (A).
2
Loosen the screw on the spring platform clamp
so that you can adjust the spring platform to
install the spring.
3
Put the shock absorber upside-down in a vice
so that you can install the spring and the spring
clip - see note.
NOTE!
The length of the spring depends of the spring
rate. For shorter springs you may run out of
threads on the cylinder tube when adjusting
the spring platform. In this case use spring clip
00629-07.
NOTE!
The spring platform and spring are press fi tted.
Push hard to install the spring.
4
Measure the spring length. Adjust the spring
preload to the recommended setting, see sec-
tion Adjustments and Set-up data in this folder.
A
Spring clip
00629-05
Spring
Washer
Spring
platform
clamp
Spring
platform
Bump rubber
1
2
3
5
Install the shock absorber to the vehicle ac-
cording to the procedure in this folder. Check
sag and ride height (see the Owner’s Manual)
and adjust the spring preload again if neces-
sary.
NOTE!
Tighten the screw on the spring platform clamp
before riding the motorcycle.
SPRING GUIDE
4
Loosen the sub frame from the frame.
5
Loosen the upper and the lower attachments of
the original shock absorber and remove it.
NOTE!
Turn the upper bolt head horizontal to avoid
interference with the top of the reservoir. Then,
turn the bolt head 90º to make it fi t into the
attachment.
2
3
4
5
6
Install the Öhlins shock absorber in the same
way as the original unit. Use the original at-
tachment screws.
7
Put the air box, sub frame and seat back in
position and fasten them. Make sure that all
removed parts are installed in the same way as
they were before the installation.
NOTE!
Put the motorcycle back on the fl oor before
tightening the screws. Make sure the vehicle is
secure and will not tip. You may need an assist-
ant for this procedure.
Brand Rider’s weight Spring Spring rate Titanium spring
kg/pounds N/mm
Honda CRF 250 65/143 06310-08 48 06350-08
70/154 06310-09 50 06350-09
75/165 06310-10 52 06350-10
80/176 06310-11 54 06350-11
85/187 06310-12 56 06350-12
90/198 06310-13 58 06350-13
70/154 06310-09 50 06350-0
9
80
/
176 06310-11 54 06350-11
90
/
198 06310-13 58 06350-1
3
Spring clip
00629-07
/