2. Barco
  3. CLM R10
CLM R10

Barco CLM R10 Owner's manual

  • Hello! I am an AI chatbot trained to assist you with the Barco CLM R10 Owner's manual. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
Barco service bulletin
Serial Number: InfoT-900
Date: 27/04/2010
Product: CLM series
Priority code*: C
A.
”Must” modification, Barco will provide the necessary components to perform this modification
at no charge.
B.
Improves the reliability of the product.
C.
Improves the general working conditions of t he pr odu ct.
D.
For information only.
1. NEW LONG LIFE COOLING LIQUID
AVAILABLE FOR CLM
This Info-T replaces Info-T 879.
1.1 General
Phenom enon
Quick evaporation of the cooling liquid in CLM projectors with yellow or a mix of yellow-blue
cooling liquid tubes.
Cause
The permeability of the yellow tubing in c om bination with the regular blue cooling liquid
requires frequent service (min 1 time /year).
Solution
New cooling liquid has been developed in order to respond on the demand of longer service
intervals.
Replacing the blue cooling liquid with new clear cooling liquid will reduce the evaporation.
The liquid c ooling service interval are improved from 9 - 12 months to + 5 years. This
results in much lower TCO (total cost of ownership).
To replace the full content of the cooling circuit, order 2x the kit with new cooling liquid as
one bottle contains only 25 cl. Order number kit B4012970K.
Scope
All CLM projectors with yellow or with a mix of yellow-blue cooling liquid tubes.
Barco nv Media & Entertain m en t Div is io n
Noordlaan 5, B-8520 Kuurne
www.barco.com
Page 1 of 8
Barco service bulletin
2. REPLACING THE COOLING LIQUID
About the replacement
The old and the new cooling liquid does not mix together. The new liquid has a higher
density than the old one, so the old liquid remains up.
Start the refreshment procedure as indicated hereafter. Continue or repeat this procedure
until new liquid is coming out at the output.
2.1 Refresh ing th e liquid cooling cir cuit
Necessary tools
• Plastic tube with male valved fitting.
• Plastic tube with female valved fitting.
• Syringe equipped with male valved fitting.
• Bottle w ith 1 liter cooling liquid.
• Empty bottle with a volume of one liter or higher.
•Cloths.
How to refresh the liquid cooling circuit ?
1. Release the pressure by turning the knob until the membrane is at the bottom of the
reservoir or until one feels resistance due to under pressure (vacuum). In that case open
the lid and keep turning until the m embrane is at the bottom, then close the lid again.
Image 2-1
Release pressure
2. Interrupt the liquid cooling circuit by uncoupling the valved fitting of the circuit coming
from the heat exchanger.
InfoT: InfoT-900
Page 2 of 8
Barco service bulletin
1
2
Image 2-2
Interrupt circuit
3.Insertthefreeendofanextratubewithmaleconnectorintoanemptybottleandconnect
the male connector with the uncoupled female connector.
4. Fill a plastic tube, which contains a female fitting, with cooling liquid as follows:
a)Connect a tube, which contains a female (F) fitting, to the male (M) fitting of the sy-
ringe.
b)Emerge the tube end and make sure that the piston of the syringe is completely pressed
in.
c) Extract cooling liquid into the syringe by pulling out the piston.
d)Disconnect the filled tube from the syringe. Make sure that the tube remains immersed.
bacd
M
F
Image 2-3
Filling tu be
Caution:It’simportantthatthereisnoairi
nside the tube. The pump is not self priming
and hence is only capable of sucking through small volumes of air.
5.Pushthefemalevalvedfitting of the filled tube on the male valved fitting. This is the
entrance of the liquid cooling circuit. Make sure that the inlet of the filled tube remains
immersed.
Page 3 of 8 InfoT: InfoT-900
Barco service bulletin
Image 2-4
Refresh cooling liquid
6. Activate the “Refill mode” in the “Service” menu of the projector. As a result the pump
starts and the fresh cooling liquid in the bottle is sucked into the cooling c ircuit while the
old cooling liquid is pressed out of the circuit into the empty bottle.
Note:Make sure that the end of the plastic tube remains immersed in the bottle with
fresh cooling liquid.
Image 2-5
Image 2-6
Image 2-7
7. Switch off the refill mode (set to no) after 2/ 3 of the fresh cooling liquid is sucked up
into the circuit.
InfoT: InfoT-900
Page 4 of 8
Barco service bulletin
Image 2-8
8. Reinstall the cooling circuit connections. Check if air is on top of the liquid in the reservoir.
If so, o pen the reservoir as described in "Top-up the reservoir with cooling liquid", page
5.
Fill up the reservoir again until the level is equal with the small hole in the reservoir and
close the reservoir again.
9. Pressurize the c ircuit by turning the knob to the left until there is 2 cm free thread be-
tween the knob and the bottom of the reservoir.
2 cm
Image 2-9
Pressurize cooling circuit
Note:Make sure the knob cannot compress the tubing when moving upwards.
2.2 Top-up the r eservo ir with cooling liquid
How to top-up
1. Release the pressure by turning the knob until the membrane is at the bottom of the
reservoir or until one feels resistance due to under-pressure (vacuum), in that case open
the lid and keep turning until membrane is at the bottom.
Page 5 of 8
InfoT: InfoT-900
Barco service bulletin
Image 2-10
Release pressure
2. Turn off the main lid on top of the reservoir (A).
A
B
Image 2-11
Open reservoir
3. Turn the bleed lid a little and take it out (B). Hold a clot ready in case there is still some
pressure on the circuit.
4.Turnoutthethirdlidusingthebacksideofthemainlid(C&D).
InfoT: InfoT-900
Page 6 of 8
Barco service bulletin
CD
Image 2-12
5. The rest of the blue liquid is c ollected on top of the reservoir. Use a syringe to remove
this liquid.
6. Top-up the reservoir with cooling liquid until the level is equal with the small hole in the
reservoir.
Image 2-13
Filling r eservoir
7. Activate the “Refill mode” in the “Service” menu of the projector to remove the air out of
the circuit.
Gently tap the radiator/tubes to remove
potential air bubbles.
Add liquid again until the level is equal with the small hole in the reservoir.
Deactivate the “Refill mode”.
8. Close the third lid again us ing the back side of the main lid.
9. Turn in the bleed lid.
Clean up r emaining liquid.
10.Close the main lid.
11.Pressurize the circuit by turning the knob to the left until there is 2 cm free thread
between the knob and the bottom of the reservoir.
Page 7 of 8
InfoT: InfoT-900
Barco service bulletin
2 cm
Image 2-14
Pressurize cooling circuit
Note:Make sure knob cannot compress the tubing when moving upwards.
If there is still an air bubble visible, redo the procedure.
3. MODIFICATION APPROVALS
3.1 Approvals
Modification approved by:
Director Customer
Service
R&D Manager
Product Manager Quality Manager
If you should have any more questions, or remarks, please do not hesitate to contact our
technical support team via the following web site w
ww.Barco.com/esupport.
InfoT: InfoT-900
Page 8 of 8
28 Apr 2010
Hans Korremans
27 Apr 2010
Stijn Cuvelier
27 Apr 2010
Sharon Dagan
28 Apr 2010
Mieke Flour
p.p. Herman De Munter
/