RocketFish RF-RBWS02 Quick setup guide

Brand: RocketFish

Model: RF-RBWS02

Type: Quick setup guide

RF-RBWS02 Wireless Outdoor Speaker

QUICK SETUP GUIDE

Initial setup

1 Unpack the package contents

2 Adjust the antennas

For best results, raise the antennas of the sender/receiver

to the vertical position.

Tip: In some cases, you may improve range by rotating both antennas

45° to create a 90° angle similar to a wide “V”.

3 Enable the remote control battery

Remove the tab from the bottom of the

remote control.

Installing batteries in the wireless speaker

(skip this if you are not using batteries)

1 Unscrew the bottom cover (three screws).

2 Insert eight alkaline or rechargeable NiMH C

batteries matching the +/- symbols as indicated.

Note: This product will only recharge NiMH batteries.

Do not try to charge any other batteries such as NiCad

batteries in this product.

3 Replace the cover and fasten the three screws.

4 Turn on the wireless speaker using the power

switch on the top panel.

Package contents

Sender/Receiver

AC power adapter

for sender/receiver

User Guide

Remote control

3.5 mm to RCA adapter

(6 inches/15.25 cm)

Wireless speaker

AC power adapter

for wireless speaker

3.5 mm

audio cable

Quick Setup Guide

Establishing communication

The sender/receiver and wireless speaker were pre-joined so they will communicate with each

other right out of the box. So if this is your rst Rocketboost enabled product you can skip this step

and go to the next section, Listening to music step.

If you need to rejoin the sender/receiver to the wireless speaker, and this is your only Rocketboost

enabled product, then use the following steps.

1 Set the HUB STATUS switch on the sender/receiver to ENABLE if this is your rst Rocketboost

product set.

• The power indicator turns green when the HUB STATUS switch is set to ENABLE.

• The power indicator turns blue when the HUB STATUS switch is set to DISABLE.

2 Press and hold on the sender/receiver for more than three seconds to put it into joining

mode. The power indicator starts blinking rapidly and the unit will stay in joining mode for

30 seconds.

3 Press and hold the power/join button on the wireless speaker for more than three seconds

so the sender/receiver and wireless speaker enter connection mode.

• The power indicator lights steadily if the joining was successful.

• The power indicator blinks slowly if the joining was not successful.

4 After the link is established, if the Source indicator on

the wireless speaker is still not illuminated, make sure

that your source is turned on.

For more instructions, see your User Guide.

If you already have other Rocketboost devices you need

to join both the sender/receiver and the wireless speaker

to your existing hub device. See the User Guide for

detailed instructions on how to do this.

Listening to music

1 Turn on the wireless sender/receiver and wireless speaker. The power indicator LEDs should

light steadily. If they are blinking you need to rejoin the sender/receiver and wireless speaker.

See the Establishing communication step above.

2 Play music from the audio device connected to your sender/receiver and listen to it from the

wireless speaker.

3 Adjust the volume level on your wireless speaker. If you have multiple audio sources in your

Rocketboost network, press the Source button on the wireless speaker to hear the next audio

source. Press the Source button again to cycle through all available audio sources.

× 8

Wireless

speaker

Eight alkaline or

rechargeable NiMH C

batteries (not included)

Rocketboost network notes:

Every Rocketboost network must contain

one hub device, which helps devices join

the network. The network can have only

one hub, which you can enable using the

hub switch on the back of all Rocketboost

senders and sender/receivers. If this is your

rst Rocketboost product, you should

make this device the hub, if you already

have Rocketboost products, you should

disable hub mode on this device.

Important: Hub devices must always have

power for your network to operate. The

hub device can be in standby (power-

saving) mode, but must stay plugged in.

ENGLISH 10-0969

15VDC

BASS

Connecting the DC adapter to the wireless speaker

(if you are not using batteries, or if you want to charge the batteries)

1 Connect the AC power adapter to the wireless

speaker and plug into an AC power outlet.

2 Turn on the wireless speaker using the power switch

on the top panel.

Note: If you are using NiMH rechargeable batteries, your

batteries will recharge whenever the speaker is connected

to a power outlet with the DC adapter. If batteries are not

fully charged, you should charge them for 16 hours before

using the wireless speaker.

15V DC

Connecting audio source and power to sender/receiver

1 Connect one end of the audio cable (supplied) to the AUDIO IN jack on the sender/receiver

and the other end to the audio output jack of your device (such as an A/V receiver, PC, or iPod).

2 Remember to turn the volume up on the source device to at least 80% of its maximum volume

if connected to a headphone output.

3 Connect the AC power adapter to the sender/receiver and plug into an AC power outlet.

The sender/receiver automatically turns on and the power indicator turns green.

To audio

output jack

To audio

output jack

Included

3.5 mm cable

Included 3.5 mm cable and

3.5 mm to RCA adatper

Lights when

speaker is

receiving

audio from

sender

RocketFish RF-RBWS02 Quick setup guide

RocketFish RF-RBWS02 Quick setup guide

RocketFish RF-RBWS02 Quick setup guide

Related papers

Other documents