DFI VC70B-KU is a versatile and powerful system featuring a Mini PCIe slot, COM ports, and various I/O options, making it suitable for industrial automation, digital signage, and other embedded applications. Its compact size and fanless design ensure quiet operation and reliable performance even in harsh environments.
DFI VC70B-KU is a versatile and powerful system featuring a Mini PCIe slot, COM ports, and various I/O options, making it suitable for industrial automation, digital signage, and other embedded applications. Its compact size and fanless design ensure quiet operation and reliable performance even in harsh environments.
1
VC70B-KU Installation Guide
Package Contents
DFI reserves the right to change the specications at any time prior to the product's release. For the latest revision and details of the
installation process, please refer to the user's manual.
www.d.com
Note:
The CD that came with the system contains an autorun screen to install drivers, utilities,
and software applications required to enhance the performance of the system and a user's
manual for your reference. Insert the CD into a CD-ROM drive. The autorun screen will
appear. If after inserting the CD, “Autorun” did not automatically start, please go directly to
the root directory of the CD and double-click “Setup”. Please install all required drivers.
•
1 VC70B-KU system unit
• 4
Mounting screws for Mini PCIe module
•
1 Quick Installation Guide
•
1 Disk includes:
- Drivers / Manual
2
Panel
Front View
COM 1 COM 2
VGA
Reset
Power button
(Green LED)
Status LED (Blue)
HDD LED
COM 6
Note:
You can congure the COM 4 port to be a CAN bus (Controller Area Network) inter-
face instead.
COM 5
COM 4/ 8-bit DIO
CANbus*
Rear View
COM 3
(RS232/RS422/RS485)
USB 3.0
LAN 2 LAN 1
HDMI
Line-out
Antenna
hole
Mic-in
DC-in
USB 2.0
3
4. After removing the mounting screws, lift the bottom side of the chassis cover
to open the system. The HDD mounting posts are readily accessible after re-
moving the bottom cover. To access the Mini PCIe slots, the power board has to
be removed.
Removing the Chassis Cover
Please observe the following guidelines and follow the procedure to open the system.
Chassis screw
1. Make sure the system and all other peripheral devices connected to it have
been powered off.
2. Disconnect all power cords and cables.
3. The 2 mounting screws on the bottom side of the system are used to secure
the cover to the chassis. Remove these screws and then put them in a safe
place for later use.
Mounting screw
Mounting screw
4
Installing a Mini PCIe Card
2. Push the Mini PCIe card down and use the provided mounting screws to se-
cure the card on the system board.
The system board is equipped with 2 Mini PCIe slots: one full-size and one half-
size slot. Here we will demonstrate the installation of a full-size Mini PCIe card.
The Mini PCIe sockets are located on the main board; to access the main board,
detach the power board on top of it. Remove the screws that afx the front bezel
as shown in the following pictures to access the power board and uninstall it from
the system.
Notes:
1. The system also has a half-size Mini PCIe slot that can accommodate either a Mini PCIe or an
mSATA card. Refer to jumper settings for signal selection for this slot.
2. The power board connects to the mainboard with a 4-pin power cable, please reconnect this cable
if it is removed during installation.
Screw
Power cable
Screw
Mounting screw
5
Board Layout and Jumper Settings
www.d.com
Note:
You cannot use COM 4 and DIO at the same time.
Please adjust JP1 and JP2 together.
DC-in
1
6
1
1
1
3
1
Mini PCIe /mSATA
1
1
12
12
1
Reset
Power
Front
Panel
(JP11)
DDR4 DDR4
DDR4
DDR4
COM 4
(RS232/DIO/CAN bus)
LAN 2
LAN 1
USB 2
USB 1
USB 3.0
USB 4
USB 3
COM 3 (RS232)
COM 2 (RS232/422/485)
COM 1(RS232/422/485)
VGA
USB 3.0
SATA 3.0
SPI Flash
BIOS
JP2
JP1
Battery
Mini PCIe
MIC-inLINE-out
HDMI
SATA_2
SATA Power
Realtek ALC888
Intel
WGI210AT
JP3
JP4
COM4/DIO Pin Select
COM4/DIO Pin Select
Clear CMOS
Mini PCIe PCIe/
SATA Select
(JP3)
(JP4)
Auto PWR ON
(JP1)
(JP2)
(JP7)
1
SATA 3.0
LED 1
1 5
2
1
40
39
LVDS
LCD Panel
SATA_0
USB 2.0 7/8
1
2
10
1
2
1
2
COM 6 COM 5
COM4 / DIO Pin Select JP1
COM4 1-2, 4-5, 7-8,
10-11 On (default)
DIO 2-3, 5-6, 8-9,
11-12 On
COM4 / DIO Pin Select JP2
COM4 1-2, 4-5, 7-8,
10-11 On (default)
DIO 2-3, 5-6, 8-9,
11-12 On
Mini PCIe/SATA Select JP3
PCIe 2-3 On
SATA 1-2 On
(default)
Clear CMOS JP4
Normal 1-2 On (default)
Clear CMOS 2-3 On
Auto PWR ON JP7
Normal 1-2 On (default)
Auto-PWR ON 2-3 On
6
Delay Turn-on/off Switch
The DIP switch (SW1) on the power board can be used to turn on or off the sys-
tem at a specic on/off delay time via car ignition.
SW1-2: System-on delay enable/disable
On (Default) Enable (delay time setting adjust-
able by SW1-4 and 1-5 as shown in
the table below)
Off Disable (System-on delay = 3 sec)
SW1-4 and 1-5: System-on delay time setting
4 5 Time
On On 10 sec (default)
Off On 30 sec
On Off 1 min
Off Off 5 min
SW1-3: System-off delay enable/disable
On (Default) Enable (delay time setting adjust-
able by SW1-6, 1-7 and 1-8 as
shown in the table below)
Off Disable (System-off delay = 0 sec)
SW1-6, 1-7 and 1-8: System-off delay time setting
6 7 8 Time
On On On 30 sec (default)
Off On On 1 min
On Off On 3 min
Off Off On 5 min
On On Off 10 min
Off On Off 15 min
On Off Off 30 min
Off Off Off 1 hr
www.d.com
Notes:
1. The OS will start the shut-down procedure when the car ignition switches off.
2. Please make sure that system-off delay time is sufcient to allow the OS to shut
down completely.
3. Please do not alter the SW1-1 (should be "ON") setting to prevent damage to the
system board.
4. Please do not push the power button during system startup or shutdown.
A52701903
-
1
-
2
-
3
-
4
-
5
-
6
DFI VC70B-KU User manual
- Type
- User manual
- This manual is also suitable for
DFI VC70B-KU is a versatile and powerful system featuring a Mini PCIe slot, COM ports, and various I/O options, making it suitable for industrial automation, digital signage, and other embedded applications. Its compact size and fanless design ensure quiet operation and reliable performance even in harsh environments.
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
