ICP DAS USA PM-3133-RCT2000P-MTCP User manual

PM-3133-RCT User’s Manual v1.00 Last Revised: Mar. 2017 Page: 1

PM-3133-RCT User’s Manual v1.00 Last Revised: Mar. 2017 Page: 2

Chapter 1 Introduction .................................... 4

1.1. PM-3133-RCT introduction 4

1.2. Caution ............................. 5

1.2.1. Danger .............................. 5

1.3. Warning ............................ 5

1.4. Product Warranty &

Customer Support ............. 5

1.4.1. Limitation of Warranty ....... 6

Chapter 2 Specifications ................................. 7

2.1 Specifications.................... 7

Chapter 3 Installation ............................... 9

3.1 Inspection ......................... 9

3.2 Safety ............................... 9

3.2.1 Dimension and Latch ........ 9

3.2.2 Mounting and Dismounting

....................................... 11

3.2.3 Positional Accuracy......... 12

3.2.4 CT’s installation steps ..... 12

Chapter 4 Wiring Diagrams ........................... 12

4.1 Connection ...................... 13

4.2 Wiring .............................. 15

Chapter 5 Relay output & LED Indicator ........ 17

5.1 Relay ............................... 17

5.2 LED Indicator .................. 17

Chapter 6 Modbus-RTU communication ........ 18

6.1.1 SW1－SW6 setting .......... 18

6.2 Modbus-RTU setting ....... 21

6.2.1 Specifications .................. 21

6.2.2 Modbus Register ............. 23

Chapter 7 Modbus-TCP Communication ....... 29

7.1 Default settings ............... 29

7.1.1 Ethernet configurations.... 30

7.2 Specifications .................. 32

7.2.1 Modbus Register ............. 32

7.3 Connecting the Power and

Host PC (without PoE)..... 33

PM-3133-RCT User’s Manual v1.00 Last Revised: Mar. 2017 Page: 3

Chapter 8 CANopen communication ............. 34

8.1 CANopen setting ............. 34

8.2 CANopen Protocol .......... 36

8.2.1 SDO Introduction ............ 37

8.2.1.1 Upload SDO Protocol ...... 37

8.2.1.2 Download SDO Protocol . 39

8.2.1.3 Abort SDO Transfer Protocol

....................................... 42

8.2.2 PDO Introduction ............ 45

8.2.2.1 PDO COB-ID Parameters 45

8.2.2.2 Transmission Type.......... 46

8.2.2.3 PDO Communication Rule

....................................... 47

8.2.3 NMT Introduction ............ 49

8.2.3.1 Module Control Protocol .. 49

8.2.3.2 Error Control Protocol ...... 51

8.2.4 Special Functions for

PM-3133-CPS ................. 52

8.2.4.1 Power Meter Data Table .. 52

8.3 Object Dictionary of

PM-3133-CPS ................. 53

8.3.1 Communication Profile Area

........................................ 53

8.3.2 Manufacturer Specific

Profile Area ..................... 59

8.3.3 Application Object ........... 63

Appendix 1: Questions & Answers ................ 64

PM-3133-RCT User’s Manual v1.00 Last Revised: Mar. 2017 Page: 4

Chapter 1 Introduction

1.1. PM-3133-RCT introduction

ICP DAS brings the most powerful, cost-effective, advanced Smart Power Meters

PM-3133-RCT that gives you access to real-time electric usage for three-phase power

measurement. With its high accuracy (<1%, PF=1; Input Current >50A), this series can

be used to both low voltage primary side and medium/high voltage secondary side and

enables the users to obtain reliable and accurate energy consumption readings from the

monitored equipments in real time under operation. These compact size and

cost-effective power meters monitoring equipment with Rogowski Coil CT is "rope-style"

Current Transformer which delivers "Easy Installation" features for large window size (55

~ 105mm) and mechanical flexibility for tight space.

Features：

 True RMS Power Measurements

 Energy Analysis for 3P4W-3CT, 3P3W-2CT, 3P3W-3CT, 1P2W-1CT, 1P3W-2CT

 Current Measurements Up to 2000 A

 Voltage Measurements Up to 500 V

 Rogowski Coil Soft CT for Easy Installation

 W Accuracy Better than 1% (PF=1; Input Current >50A)

 Supports RS-485, Ethernet Interface (PoE)

 Supports Modbus RTU, Modbus TCP protocols.

 Supports 2-Power Relay Output (Form A)

 Total Harmonic Distortion (THD)

PM-3133-RCT User’s Manual v1.00 Last Revised: Mar. 2017 Page: 5

1.2. Caution

1.2.1. Danger

The meter contains hazardous voltages, and should never be disassembled. Failing to

follow this practice will result in serious injury or death. Any work on or near energized

meters, meter sockets, or other metering equipment could induce a danger of electrical

shock. It is strongly recommended that all work should be performed only by qualified

industrial electricians and metering specialist. ICP DAS assumes no responsibility if

your electrical installer does not follow the appropriate national and local electrical

codes.

1.3. Warning

ICP DAS assumes no liability for any damage resulting from the use of this product. ICP

DAS reserves the right to change this manual at any time without notice. The

information furnished by ICP DAS is believed to be accurate and reliable. However, no

responsibility is assumed by ICP DAS for its use, not for any infringements of patents or

other rights of third parties resulting from its use.

1.4. Product Warranty & Customer Support

ICP DAS warrants all products free from defects in material and workmanship for a

period of one year from the date of shipping. During the warranty period, we will, at our

position, either repair or replace any product that proves to be defective. To report any

defect, please contact ：+886-3- 597-3366 or service@icpdas.com.

Please have the model, serial number and a detailed problem description available

when you call. If the problem concerns a particular reading, please have all meter

readings available. When returning any merchandise to ICP DAS, a return SN. is

required.

PM-3133-RCT User’s Manual v1.00 Last Revised: Mar. 2017 Page: 6

1.4.1. Limitation of Warranty

This warranty does not apply to defects resulting from unauthorized modification,

misuse, or use for reason other than electrical power monitoring. The supplied meter is

not a user-serviceable product.

PM-3133-RCT User’s Manual v1.00 Last Revised: Mar. 2017 Page: 7

Chapter 2 Specifications

2.1 Specifications

Model PM-3133-RCT PM-3133-RCT-MTCP

AC Power Measurement

Wiring 1P2W-1CT, 1P3W-2CT, 3P3W-2CT, 3P3W-3CT and 3P4W-3CT

Measurement Voltage 10 ~ 500 V (CAT III)

Measurement Current CTØ55 mm (500 A), CTØ80 mm (1000 A), CTØ105 mm (2000 A)

Measurement Frequency

50-60 Hz

W Accuracy Better than 1% (PF=1; Input Current >50 A)

Starting Current >10 A

Power Parameter

Measurement

True RMS voltage (Vrms), True RMS current (Irms), Active Power (kW),

Active Energy (kWh), Apparent Power (kVA), Apparent Energy (kVAh),

Reactive Power (kVAR), Reactive Energy (kVARh), Power Factor (PF),

Frequency(Hz)

Data Update Rate 1 Second

Communication

RS-485

Protocol Modbus-RTU -

Baud rate

9600,19200 (default), 38400,

115200; DIP Switch Selectable

-

Data

format

N,8,1 (default); N,8,2; E,8,1; E,8,2;

O,8,1; O,8,2 (

FW version 1.07)

Isolation 3000 VDC -

Bias

Resistor

No (Usually supplied by the

RS-

485 Master. Alternatively, add

a tM-SG4 or SG-785)

Ethernet

Protocol - Modbus TCP

PoE - Yes, IEEE 802.3af

Alarm Output

Power Relay

Form A (Normal Open) x 2; Relay Contact Voltage Range: 5 A @ 250

VAC (47 ~ 63Hz), 5 A @ 30 VDC

PM-3133-RCT User’s Manual v1.00 Last Revised: Mar. 2017 Page: 8

Field Wiring Terminal Markings:

3.81mm (For Measurement Current and Communication): Use Copper Conductors Only,

wires range 16-26 AWG, torque value 3.0 lb-in.

5.08mm (For Measurement Voltage, Aux Power and Alarm Output):

Use Copper Conductors Only, wires range 12-24 AWG, torque value 7.0 lb-in.

7.62mm: Use Copper Conductors Only, wires range 12-24 AWG, torque value 4.5 lb-in.

Aux Power

Input Range +12 ~ 48 VDC

+12 ~ 48 VDC or PoE

PoE Pin Assignments:

+ (Pin 1, 2), V- (Pin 3, 6)

Power Consumption 2 W

Dimensions (W x L x H)

127 mm x 105 mm x 33 mm

Environment

Operating Temperature -20 ~ +70 °C

Storage Temperature -40 ~ +80 °C

PM-3133-RCT User’s Manual v1.00 Last Revised: Mar. 2017 Page: 9

Chapter 3 Installation

3.1 Inspection

The instrument is no longer safe when,

a) Shows clear signs of damage

b) Does not work

c) Long storage under extreme conditions

d) Damage during shipment

3.2 Safety

Please use the soft dry clothes to clean the instrument.

Please do not use any chemical or detergent or volatile solvents to clean the instrument,

in order to avoid any possibility of the cover damage.

3.2.1 Dimension and Latch

PM-3133-RCT User’s Manual v1.00 Last Revised: Mar. 2017 Page: 10

 Products come with external split type clip-on CT’s. Disconnect the CT’s or use

other CT’s is highly prohibited.

 Please read this operation manual carefully before using.

 Please re-confirm the measure position.

 PM-3133 series can be installed as rail mounting mode or embedded, no need to

drill a hole or screw to fix it (rail mounting width can up to the length of 35 mm).

 Meter auxiliary power is DC +12V ~+48V.

Models

A

B

PM-3133-RCT500P 55.0 68.5

PM-3133-RCT1000P

80.0

93.5

PM-3133-RCT2000P

105.0

118.5

PM-3133-RCT User’s Manual v1.00 Last Revised: Mar. 2017 Page: 11

3.2.2 Mounting and Dismounting

 Mounting

Assembly: Place the PM-3133 on the DIN-Rail. Push the front of the PM-3133

toward the mounting surface until it audibly snaps into place.

Dismantling: Pull out the latch and then remove the PM-3133 from the DIN-rail.

 Wire Disconnection

1. Open the CT clip to detach the CT, do not remove the CT terminal lines if

possible

Note: if you need to remove the terminal lines, always detach the CT before

removing the CT terminal lines. Otherwise the CT may develop open-circuit

secondary voltages which may be hazardous to personnel or damaging to the

CT or equipment connected in the secondary circuit.

2. Disconnect the voltage input wires from terminals and wrap the wire tips with

plastic tape.

3. Disconnect the communication wires from terminal.

4. Disconnect the auxiliary power from terminal and wrap the wire tip with plastic

tape.

PM-3133-RCT User’s Manual v1.00 Last Revised: Mar. 2017 Page: 12

3.2.3 Positional Accuracy

1. W Accuracy Better than 1% (PF=1; Input Current >50A; the “A” area).

2. Due to small variations in the winding density and coil cross-sectional area the

transducer output varies slightly depending on the position of the current within the coil

loop.

The diagram below shows the variation of accuracy throughout the coil. The variation is

greatest when the current is positioned near the junction of the connecting cable and the

coil, where there is some discontinuity, and the error here can be

typically 5%. Since in most applications the current is distributed

throughout a significant part of the area contained by the coil loop the

reading will be very close to the calibration value.

3.2.4 CT’s installation steps

Type

A

B

C

D

Accuracy 1% 3% 5% >5%

The current should not be positioned close to the

coil-cable junction (shown by the “D” area) since

the error for this region is greater.

PM-3133-RCT User’s Manual v1.00 Last Revised: Mar. 2017 Page: 13

Chapter 4 Wiring Diagrams

4.1 Connection

Please firstly check the current input terminal, and then in white black, white black,

white black wire sequences (CT1-K, CT1-L, CT2-K, CT2-L, CT3-K,CT3-L). Then

connect the CT’s, and close the CT clip. Make sure the arrow direction sign on CT’s

follows current flow direction（K→L）

Note: it must be in the same direction.

Connect the voltage input terminal N C B A. for PM-3133, in the three phase order

as follows on N C B A.

Attention please!! For 3P3W-2CT, connect in N C A phase sequence, do not

connect phase B (Check the diagram).

PM-3133-RCT User’s Manual v1.00 Last Revised: Mar. 2017 Page: 14

Voltage Input

1. PM-3133 series: Input Voltage up to 500V.

For any higher Input Voltage large than 500V, please add the PT (power transformer), and Change PT

RATIO setup.

2. Confirm the RST (ABC) phase sequence.

Current Input

1. The external CT’s are fragile, please handle with care.

2. The current input of PM-3133 series is in mA range. Only the ex-factory attached CT’s can be used.

The other CT’s, for example, from panel will damage the instrument due to its large current (around

5A)

3. When more than one smart meter (PM-3133 series) are installed, please do not disconnect the CT

with its original meter and mix use with each other. Since each set of smart meter (PM-3133 series)

and its attached split type clip-on CT are calibrated set by set. The mix use may cause wrong

measurements.

4. To install CT’s correctly, please ensure the CT lines sequences is right before clip the CT’s onto the

power cable of the monitoring equipment. (Detail will be found in next section)

5. When measuring the current, the secondary circuit of a CT should never be

opened when a load is passing through its primary. Make sure you always open

the CT clip to detach the CT before removing the terminal lines. Otherwise, it will cause severe

injury.

6. Please handle with extra care, especially when the operation space of CT’s is limited.

7. The current direction must follow K-L marked on CT’s.

8. Please select the right size CT’s for different size of monitoring equipment cables:

power cable diameter ＜Φ55 use 500A CT，Φ80 use 1000A CT，Φ105 use 300A CT.

9. The maximum current value cannot exceed the CT rating

PM-3133-RCT User’s Manual v1.00 Last Revised: Mar. 2017 Page: 15

4.2 Wiring

 1P2W-1CT(PM-3133)

 1P3W-2CT(PM-3133)

 3P3W-2CT(PM-3133)

PM-3133-RCT User’s Manual v1.00 Last Revised: Mar. 2017 Page: 16

 3P3W-3CT(PM-3133)

DIP switch: Wiring mode

SW 9 SW 10

3P3W-3CT

OFF

ON

 3P4W-3CT(PM-3133)

DIP switch: Wiring mode

SW 9 SW 10

3P4W-3CT

ON

PM-3133-RCT User’s Manual v1.00 Last Revised: Mar. 2017 Page: 17

Chapter 5 Relay output & LED Indicator

5.1 Relay

Relay type Power Relay, Form A (SPST N.O.)

Operating Voltage Range 250 VAC/30 VDC

Max. Load Current 5 A at 25 °C

Operate Time 6 ms

Release Time 3 ms

5.2 LED Indicator

The PM-3133 has 4 LED to indicate the unit power status, RS-485 communication, and

power data calculation.

 RUN: Green, light up after RS-485 ready. LED will flash when the unit is processing

RS-485 communication.

 PWR: Red, Power on LED always on.

 DO0: Green. LED DO0 will light up, when DO0 is “ON”.



DO1: Green. LED DO1 will light up, when DO1 is “ON”.

PM-3133-RCT User’s Manual v1.00 Last Revised: Mar. 2017 Page: 18

Chapter 6 Modbus-RTU communication

6.1 RS-485 setting

 Default setting for RS-485: 19200, n, 8, 1

 DIP switch (SW1-SW6) is used for Modbus address setting, default is 1, i.e.

all OFF

For example: Modbus address is 10，find the table of DIP switch 1-6 is

ON, OFF, OFF, ON, OFF, OFF

6.1.1 SW1

－

SW6 setting

Setting Modbus-RTU address for communication (1-64)

Modbus Address

SW 1

SW 2

SW 3

SW 4

SW 5

SW 6

1

OFF

2

ON

OFF

3

OFF

ON

OFF

4

ON

OFF

5

OFF

ON

OFF

6

ON

OFF

ON

OFF

7

OFF

ON

OFF

8

ON

OFF

9

OFF

ON

OFF

10

ON

OFF

ON

OFF

11

OFF

ON

OFF

ON

OFF

12

ON

OFF

ON

OFF

13

OFF

ON

OFF

14

ON

OFF

ON

OFF

15

OFF

ON

OFF

16

ON

OFF

17

OFF

ON

OFF

18

ON

OFF

ON

OFF

19

OFF

ON

OFF

ON

OFF

20

ON

OFF

ON

OFF

21

OFF

ON

OFF

ON

OFF

22

ON

OFF

ON

OFF

ON

OFF

23

OFF

ON

OFF

ON

OFF

24

ON

OFF

ON

OFF

25

OFF

ON

OFF

26

ON

OFF

ON

OFF

27

OFF

ON

OFF

ON

OFF

PM-3133-RCT User’s Manual v1.00 Last Revised: Mar. 2017 Page: 19

28

ON

OFF

ON

OFF

29

OFF

ON

OFF

30

ON

OFF

ON

OFF

31

OFF

ON

OFF

32

ON

OFF

33

OFF

ON

34

ON

OFF

ON

35

OFF

ON

OFF

ON

36

ON

OFF

ON

37

OFF

ON

OFF

ON

38

ON

OFF

ON

OFF

ON

39

OFF

ON

OFF

ON

40

ON

OFF

ON

41

OFF

ON

OFF

ON

42

ON

OFF

ON

OFF

ON

43

OFF

ON

OFF

ON

OFF

ON

44

ON

OFF

ON

OFF

ON

45

OFF

ON

OFF

ON

46

ON

OFF

ON

OFF

ON

47

OFF

ON

OFF

ON

48

ON

OFF

ON

49

OFF

ON

50

ON

OFF

ON

51

OFF

ON

OFF

ON

52

ON

OFF

ON

53

OFF

ON

OFF

ON

54

ON

OFF

ON

OFF

ON

55

OFF

ON

OFF

ON

56

ON

OFF

ON

57

OFF

ON

58

ON

OFF

ON

59

OFF

ON

OFF

ON

60

ON

OFF

ON

61

OFF

ON

62

ON

OFF

ON

63

OFF

ON

64

ON

PM-3133-RCT User’s Manual v1.00 Last Revised: Mar. 2017 Page: 20

 SW7－SW8 setting

PM-3133：For Baud Rate Setting

Baud Rate

SW 7

SW8

9600 bps

OFF

19200 bps (Default)

ON

OFF

38400 bps

OFF

ON

115200 bps

ON

Add the Bias Resistor on RS-485 Network for stable signal

The RS-485 master is required to provide the bias for PM-3133 series. Otherwise, the tM-SG4

or SG-785 should be added to provide the bias. All ICP DAS controllers and converters provide

the bias.

 SW9－SW10 setting

PM-3133：Select the different wiring mode

(Please select the Software setting, if 1P2W-1CT or 1P3W-2CT is used)

Wiring

SW 9 SW 10

Software setting

OFF

3P3W-2CT

ON

OFF

3P3W-3CT

OFF

ON

3P4W-3CT

ON

Page is loading ...

ICP DAS USA PM-3133-RCT2000P-MTCP User manual

ICP DAS USA PM-3133-RCT2000P-MTCP User manual

Related papers

Other documents