ViewSonic X10-4K-S User guide

X10-4K

Lamp Free Smart Theater

User Guide

Model No. VS17612

P/N: X10-4K

IMPORTANT: Please read this User Guide to obtain important information on installing and using your product in

a safe manner, as well as registering your product for future service. Warranty information contained in this User

Guide will describe your limited coverage from ViewSonic® Corporation, which is also found on our web site at

http://www.viewsonic.com in English, or in specific languages using the Regional selection box in the upper right

corner of our website. “Antes de operar su equipo lea cu idadosamente las instrucciones en este manual”

2

Thank you for choosing ViewSonic®

As a world-leading provider of visual solutions, ViewSonic® is dedicated to exceeding

the world’s expectations for technological evolution, innovation, and simplicity.

At ViewSonic®, we believe that our products have the potential to make a positive

impact in the world, and we are confident that the ViewSonic® product you have

chosen will serve you well.

Once again, thank you for choosing ViewSonic®!

3

Safety Precautions

Please read the following  before you start using the projector.

• Keep this user guide in a safe place for later reference.

• Read all warnings and follow all instrucons.

• Allow at least 20“ (50 cm) clearance around the projector to ensure proper

venlaon.

• Place the projector in a well-venlated area. Do not place anything on the

projector that prevents heat dissipaon.

• Do not place the projector on an uneven or unstable surface. The projector may

fall over, causing personal injury or projector malfuncon.

• Do not use if the projector is lted at an angle of more than 10° degrees le or

right, nor at an angle of more than 15° degrees forwards or backwards.

• Do not look straight at the projector lens during operaon. The intense light

beam may damage your eyes.

• Always open the lens shuer or remove the lens cap when the projector lamp is

on.

• Do not block the projecon lens with any objects when the projector is under

operaon as this could cause objects to become heated and deformed or even

cause a re.

• The lamp becomes extremely hot during operaon. Allow the projector to

cool for approximately 45 minutes prior to removing the lamp assembly for

replacement.

• Do not use lamps beyond the rated lamp life. Excessive use of lamps beyond the

rated life could cause them to break on rare occasions.

• Never replace the lamp assembly or any electronic component unless the

projector is unplugged.

• Do not aempt to disassemble the projector. There are dangerous high voltages

inside which may cause death if you should come into contact with live parts.

• When moving the projector, be careful not to drop or bump the projector on

anything.

• Do not place any heavy objects on the projector or connecon cables.

• Do not stand the projector on end vercally. Doing so may cause the projector to

fall over, causing personal injury or projector malfuncon.

• Avoid exposing the projector to direct sunlight or other sources of sustained

heat. Do not install near any heat sources such as radiators, heat registers,

stoves, or other devices (including ampliers) that may increase the temperature

of the projector to dangerous levels.

4

• Do not place liquids near or on the projector. Liquids spilled into the projector

may cause it to fail. If the projector does become wet, disconnect it from the

power supply and call your local service center to have the projector serviced.

• When the projector is under operaon, you may sense some heated air and odor

from its venlaon grill. It is a normal operaon and not a defect.

• Do not aempt to circumvent the safety provisions of the polarized or

grounding-type plug. A polarized plug has two blades with one wider than the

other. A grounding-type plug has two blades and a third grounding prong. The

wide and third blade are provided for your safety. If the plug does not t into

your outlet, obtain an adapter and do not aempt to force the plug into the

outlet.

• When connecng to a power outlet, DO NOT remove the grounding prong.

Please ensure grounding prongs are NEVER REMOVED.

• Protect the power cord from being treaded upon or pinched, parcularly at the

plug, and at the point where it emerges from the projector.

• In some countries, the voltage is NOT stable. This projector is designed to

operate safely within a voltage between 100 to 240 volts AC, but could fail if

power cuts or surges of ±10 volts occur. In areas where voltage may uctuate

or cut out, it is recommended that you connect your projector through a power

stabilizer, surge protector, or uninterruptable power supply (UPS).

• If smoke, an abnormal noise, or a strange odor is present, immediately switch

the projector o and call your dealer or ViewSonic®. It is dangerous to connue

using the projector.

• Use only aachments/accessories specied by the manufacturer.

• Disconnect the power cord from the AC outlet if the projector is not being used

for a long period of me.

• Refer all servicing to qualied service personnel.

CAUTION: Possibly hazardous opcal radiaon is emied from this product. As

with any bright light source, do not stare into the beam,

RG2 IEC 62471-5:2015.

5

Safety Precautions - Ceiling Mounting

Please read the following Safety Precautions before you start using the projector.

If you intend to mount the projector on the ceiling, it is strongly recommended

that you use a proper fitting projector ceiling mount kit and that you ensure it is

securely and safely installed.

If you use an inappropriate projector ceiling mount kit, there is a safety risk that the

projector may fall from the ceiling due to an improper attachment through the use

of the wrong gauge or length screws.

You can purchase a projector ceiling mount kit from the place you purchased your

projector.

6

Contents

Safety Precautions ....................................................... 3

Introduction ................................................................ 9

Features .................................................................................................................. 9

Package Contents .................................................................................................10

Product Overview .................................................................................................11

Projector - Controls and Functions ........................................................................ 11

Connection Ports ................................................................................................... 13

Remote Control - Controls and Functions ............................................................. 14

Remote Control - Effective Range ......................................................................... 15

Remote Control - Replacing the Batteries ............................................................. 15

Initial Setup ............................................................... 16

Choosing a Location - Projection Orientation .......................................................16

Projection Dimensions .................................................................... ......................17

Mounting the Projector ........................................................................................18

Making Connections .................................................. 19

Connecting to Power ............................................................................................19

vRemote App ........................................................................................................20

Connecting to External Devices ............................................................................21

HDMI Connection .................................................................................................. 21

USB-C Connection ................................................................................................. 21

Wireless Screen Mirroring ..................................................................................... 22

Connecting to Audio .............................................................................................23

Bluetooth Speaker ................................................................................................. 23

Voice Control ......................................................................................................... 24

Connecting to Networks .......................................................................................28

Wi-Fi Connection ................................................................................................... 28

Custom SSID .......................................................................................................... 30

Wired LAN Connection .......................................................................................... 32

Using the Projector .................................................... 33

Starting Up the Projector .................................................................... ..................33

First Time Activation ............................................................................................. 33

Preferred Language ............................................................................................... 33

Projection Orientation .......................................................................................... 34

Network Settings ................................................................................................... 34

Source Input .......................................................................................................... 35

7

Selecting an Input Source .....................................................................................37

Adjusting the Projected Image .............................................................................38

Adjusting the Projector's Height and Projection Angle ......................................... 38

Shutting Down the Projector ................................................................................39

Input Source Selected - On-Screen Display (OSD) Tree ......................................... 40

Operating the Projector ............................................. 53

Home Screen ........................................................................................................53

Home Screen - On-Screen Display (OSD) Menu Tree ...........................................54

Menu Operations .................................................................................................59

Aptoide .................................................................................................................. 59

Apps Center ........................................................................................................... 60

File Management .................................................................................................. 62

Setting ................................................................................................................... 66

Appendix ................................................................... 84

Specifications .................................................................... .................................... 84

Projector Dimensions ............................................................................................ 86

Timing Chart .........................................................................................................86

HDMI/USB-C Video Timing .................................................................................... 86

IR Control Table ....................................................................................................88

Glossary ................................................................................................................89

Troubleshooting ...................................................................................................91

LED Indicators ........................................................................................................ 92

Maintenance.........................................................................................................93

General Precautions .............................................................................................. 93

Cleaning the Lens .................................................................................................. 93

Cleaning the Case .................................................................................................. 93

Storing the Projector ............................................................................................. 93

Regulatory and Service Information .......................... 94

Compliance Information ....................................................................................... 94

FCC Compliance Statement ................................................................................... 94

Industry Canada Statement ................................................................................... 94

CE Conformity for European Countries ................................................................. 95

Declaration of RoHS2 Compliance......................................................................... 96

Indian Restriction of Hazardous Substances ......................................................... 97

Product Disposal at End of Product Life ................................................................ 97

8

Copyright Information ..........................................................................................98

Customer Service .................................................................................................. 99

Limited Warranty ................................................................................................ 100

Mexico Limited Warranty .................................................................................... 103

9

Introduction

Combining stunning 4K resoluon with smart streaming funconality and a

portable design, the ViewSonic® X10-4K projector delivers a theater-like experience

in any room. With a lightweight design, easy carry handle, and short throw lens,

the X10-4K can be conveniently moved from room to room, indoors to outdoors. It

features 2,400 LED lumens of brightness, and with Wi-Fi connecvity, allows users

to stream content from their favorite providers.

Features

• Short throw lens design allows for a projected 100” screen size from only 1.77

meters away.

• Auto V. keystone to correct a distorted image automacally.

• Bluetooth speaker, Auto Focus, and Screen Mirroring features.

• USB-C for video transmission and power supply.

• Eye protecon feature in the event objects get too close to the light source (50

cm or 100 cm).

• 16 GB internal storage (Max. 12 GB available for user storage).

• Various Color modes for dierent projecon purposes.

• Mul-language On-Screen Display (OSD) menus.

10

Package Contents

Item 

[1] X10-4K Projector

[2] Remote Control

[3] Quick Start Guide

[4] Power Cord

[5] USB-C Cable

[6] HDMI Cable

[7] Wi-Fi Dongle

[8] Batteries

 The power cord and video cables included in your package may vary

depending on your country. Please contact your local reseller for more

informaon.

11

Product Overview



Key 

Power Toggles between standby mode and power on.

Volume Increases/decreases the volume level.

12

13



Port 

[1] AC Power Cord Inlet AC Power Cord inlet

[2] Wi-Fi Dongle Wi-Fi dongle socket

[3] S/PDIF S/PDIF signal output socket

[4] AUDIO OUT (3.5 mm jack) Audio signal output socket

[5] AUDIO IN (3.5 mm jack) Audio signal input socket for Bluetooth mode

[6] HDMI 1¹ HDMI port³

[7] HDMI 2¹ HDMI port³

[8] USB-C² USB-C port

[9] MICRO SD Micro SD socket (SDXC up to 64 GB - FAT32/NTFS)

[10] LAN RJ45 LAN port

[11] USB 1 (5V/1.5A Out) USB 2.0 Type A port (USB Reader - FAT32/NTFS)

[12] USB 2 (5V/2A Out) USB 3.0 Type A port (USB Reader - FAT32/NTFS)

[13] Reset Buon Reset button for restarting the projector⁴

[14] IR Sensor IR Sensor for remote control

¹ Supports HDCP 2.0/HDMI 2.2.

² Please use the supplied USB-C cable, and ensure your USB-C device can support video transmission.

³ iPhone/iPad users will need to buy an additional adapter. To avoid compatibility issues, please use Apple

authorized accessories.

⁴ Insert a paper clip into the Reset button to restart the projector if the system freezes.

14



 

[1] Power

Turns the projector On or O

[2] Source

Displays the input source selecon bar.

[3] Focus

Automacally focus the image.

To manually adjust, press and hold the Focus buon on

the remote control for three (3) seconds

[4] Seng

Displays the  menu.

[5] Audio Mode

Displays the speaker sengs.

[6] Bluetooth

View Bluetooth opons.

[7] Up/Down/Le/Right

Navigates and selects the desired menu items and

makes adjustments.

[7] Shule Wheel Le/

Right

[8] OK

Conrms the selecon.

[9] Return

Returns to the previous screen.

[10] Home

Access the Home menu.

[11] Volume Control

Increases/decreases the volume level or mutes/

unmutes it.

15



To ensure proper funcon of the remote control

follow the steps below:

1. The remote control must be held at an angle

within 30° perpendicular to the projector’s IR

remote control sensor(s).

2. The distance between the remote control and

the sensor(s) should not exceed 8 m (26 .)

 Refer to the illustraon for the locaon

of the infrared (IR) remote control

sensor(s).



1. Remove the baery cover from the boom of the remote control by pressing the

nger grip and sliding it across.

2. Remove any exisng baeries (if necessary) and install two AAA baeries.

 Observe the baery’s polaries as indicated.

3. Replace the baery cover by aligning it with the base and pushing it back into

posion.



• Avoid leaving the remote control and baeries in excessive heat or a humid

environment.

• Replace only with the same or equivalent type recommended by the

baery manufacturer.

• If the baeries are drained or if you will not be using the remote control for

an extended period of me, remove the baeries to avoid damage to the

remote control.

• Dispose of the used baeries according to the manufacturer’s instrucons

and local environment regulaons for your region.

16



This secon provides detailed instrucons for the inial set up your projector.



Personal preference and room layout will decide the installaon locaon. Consider

the following:

• Size and position of your screen.

• Location of a suitable power outlet.

• Location and distance between the projector and other equipment.

The projector is designed to be installed in one of the following locations:



Front Table

The projector is placed near

the oor in front of the screen.

Front Ceiling

The projector is suspended

upside-down from the ceiling

in front of the screen.

Rear Table¹

The projector is placed near

the oor behind the screen.

Rear Ceiling¹

The projector is suspended

upside-down from the ceiling

behind the screen.

¹ A rear projecon screen is required.

1717



• 16:9 Image on a 16:9 Screen

 (e) = Screen / (f) = Center of Lens

16:9 Image on a 16:9 Screen

(a) Screen

Size



(c) Image

Height

Image Width

Minimum Maximum

in.

cm

in.

m

in.

m

in.

cm

in.

mm

30 76.2 20.9 0.53 20.9 0.53 14.7 37.36 26.15 664

40 101.6 27.9 0.71 27.9 0.71 19.6 49.81 34.86 886

50 127 34.8 0.88 34.8 0.88 24.5 62.26 43.58 1107

60 152.4 41.8 1.06 41.8 1.06 29.4 74.72 52.29 1328

70 177.8 48.8 1.24 48.8 1.24 34.3 87.17 61.01 1550

80 203.2 55.7 1.42 55.7 1.42 39.2 99.62 69.73 1771

90 228.6 62.7 1.59 62.7 1.59 44.1 112.07 78.44 1992

100 254 69.7 1.77 69.7 1.77 49 124.53 87.16 2214

110 279.4 76.7 1.95 76.7 1.95 53.9 136.98 95.87 2435

120 304.8 83.6 2.12 83.6 2.12 58.8 149.43 104.59 2657

130 330.2 90.6 2.3 90.6 2.3 63.7 161.88 113.3 2878

140 355.6 97.6 2.48 97.6 2.48 68.6 174.34 122.02 3099

150 381 104.5 2.66 104.5 2.66 73.5 186.79 130.74 3321

160 406.4 111.5 2.83 111.5 2.83 78.4 199.24 139.45 3542

200 508 139.4 3.54 139.4 3.54 98.1 249.05 174.32 4428

 There is a 3% tolerance among these numbers due to optical component

variations. It is recommended to physically test the projection size and

distance before permanently installing the projector.

1818



 If you buy a third party mount, please use the correct screw size. Screw

size can vary depending on the thickness of the mounng plate.

1. To ensure the most secure installaon, please use a ViewSonic® wall or ceiling

mount.

2. Ensure the screws used to aach the mount to the projector meet the following

specicaons:

• Screw type: M4 x 8

• Maximum Screw Length: 8 mm



• Avoid installing the projector near a heat source.

• Keep at least a 10 cm (3.9 in.) gap between the ceiling and the boom of

the projector.

19



This section guides you on how to connect the projector with other equipment.



1. Connect the power cord to the AC IN jack at the rear of the projector.

2. Plug the power cord into a power outlet.

 When installing the projector, incorporate a readily accessible disconnect

device in the xed wiring, or connect the power plug to an easily

accessible outlet near the unit. If a fault should occur during operaon of

the projector, use the disconnect device to switch o the power supply,

or disconnect the power plug.

2020

vRemote App

The vRemote App allows the user to control the projector via their personal mobile

device. Users can change the input source, and mute/unmute or power on/o the

projector.

To use the vRemote App:

1. Download the App from Google Play or the Apple App Store and install it on your

mobile device.

2. Enable, open, and login to the applicaon.

3. Press the “Add Device” icon.

4. Press the “Next” icon.

5. Use the camera to scan the QR Code.

6. Now you are ready to control the projector.

ViewSonic X10-4K-S, X10-4K User guide

Related papers

Other documents