Hitachi FDV 16VB Instruction Manual And Safety Instructions

Brand: Hitachi

Model: FDV 16VB

Category: Power tools

Type: Instruction Manual And Safety Instructions

English

FDV 16VB

DOUBLE INSULATION

DOUBLE ISOLATION

AISLAMIENTO DOBLE

INSTRUCTION MANUAL AND SAFETY INSTRUCTIONS

WARNING

Improper and unsafe use of this power tool can result in death or serious bodily

injury!

This manual contains important information about product safety. Please read

and understand this manual before operating the power tool. Please keep this

manual available for others before they use the power tool.

MANUAL DE INSTRUCCIONES E INSTRUCCIONES DE SEGURIDAD

ADVERTENCIA

¡La utilización inapropiada e insegura de esta herramienta eléctrica puede resultar

en lesiones serias o en la muerte!

Este manual contiene información importante sobre la seguridad del producto.

Lea y comprenda este manual antes de utilizar la herramienta eléctrica. Guarde

este manual para que puedan leerlo otras personas antes de que utilicen la

herramienta eléctrica.

MODE D’EMPLOI ET INSTRUCTIONS DE SECURITE

AVERTISSEMENT

Une utilisation incorrecte et dangereuse de cet outil motorisé peut entraîner la

mort ou de sérieuses blessures corporelles!

Ce mode d’emploi contient d’importantes informations à propos de la sécurité de

ce produit. Prière de lire et de comprendre ce mode d’emploi avant d’utiliser l’outil

motorisé. Garder ce mode d’emploi à la disponibilité des autres utilisateurs avant

qu’ils utilisent l’outil motorisé.

MODEL HAMMER DRILL

MODÉLO MARTEAU PERFORATEUR

MODELO MARTILLO ROTO-PERCUTOR

English

CONTENTS

English

Page

IMPORTANT INFORMATION ............. 3

MEANINGS OF SIGNAL WORDS ...... 3

SAFETY

IMPORTANT SAFETY INSTRUCTIONS

FOR USING ALL POWER TOOLS ..................

IMPORTANT SAFETY INSTRUCTIONS

FOR USE OF THE HAMMER DRILL

............ 7

REPLACEMENT PARTS ...................... 7

POLARIZED PLUGS ............................ 8

USE OF EXTENSION CORD ............... 8

DOUBLE INSULATION FOR SAFER OPERATION

..... 9

Page

OPERATION AND MAINTENANCE

NAME OF PARTS ................................ 10

SPECIFICATIONS ................................ 10

ACCESSORIES..................................... 11

STANDARD ACCESSORIES.............. 11

OPTIONAL ACCESSORIES ............... 11

APPLICATIONS.................................... 12

PRIOR TO OPERATION ....................... 12

HOW TO USE ...................................... 14

MAINTENANCE AND INSPECTION

...... 16

SERVICE AND REPAIRS...................... 16

PARTS LIST ......................................... 48

ÍNDICE

Español

Página

INFORMACIÓN IMPORTANTE ......... 32

SIGNIFICADO DE LAS PALABRAS DE SEÑALIZACIÓN

.. 32

SEGURIDAD

INSTRUCCIONES IMPORTANTES DE SEGURIDAD PARA

UTILIZACIÓN DE TODAS LAS HERRAMIENTAS ELÉCTRICAS

.. 33

INSTRUCCIONES IMPORTANTES DE SEGURIDAD

PARA UTILIZACIÓN DEL MARTILLO ROTO-PERCUTOR

.. 37

PIEZAS DE REEMPLAZO .................. 37

ENCHUFES POLARIZADOS ............. 38

UTILIZACIÓN DE UN CABLE PROLONGADOR

...... 38

AISLAMIENTO DOBLE PARA OFRECER UNA

OPERACIÓN MÁS SEGURA .........................

Página

OPERACIÓN Y MANTENIMIENTO

NOMENCLATURA ............................ 40

ESPECIFICACIONES ......................... 40

ACCESORIOS .................................... 41

ACCESORIOS ESTÁNDAR ............. 41

ACCESORIOS OPCIONALES .......... 41

APLICACIONES ................................. 42

ANTES DE LA OPERACIÓN .............. 42

COMO SE USA .................................. 45

MANTENIMIENTO E INSPECCIÓN..46

SERVICIO Y REPARACIONES .......... 46

LISTA DE PIEZAS .............................. 48

TABLE DES MATIERES

Français

Page

INFORMATIONS IMPORTANTES .... 17

SIGNIFICATION DES MOTS D’AVERTISSEMENT

.. 17

SECURITE

CONSIGNES DE SECURITE IMPORTANTE POUR

L'UTILISATION DE TOUS LES OUTILS ELECTRIQUES

.18

CONSIGNES DE SECURITE IMPORTANTES POUR

L’UTILISATION DU MARTEAU PERFORATEUR

.. 22

PIECES DE RECHANGE .................... 22

FICHES POLARISEES ........................ 23

UTILISATION D'UN CORDON DE RALLONGE

.. 23

DOUBLE ISOLATION POUR UN

FONCTIONNEMENT PLUS SUR ........... 24

Page

UTILISATION ET ENTRETIEN

NOM DES PARTIES

................................ 25

SPECIFICATIONS ................................ 25

ACCESSOIRES..................................... 26

ACCESSOIRES STANDARD.............. 26

ACCESSOIRES EN OPTION .............. 26

APPLICATIONS.................................... 27

AVANT L’UTILISATION ...................... 27

UTILISATION ....................................... 30

ENTRETIEN ET INSPECTION.............. 31

ENTRETIEN ET REPARATION ............ 31

LISTA DES PIECES .............................. 48

English

IMPORTANT INFORMATION

Read and understand all of the operating instructions, safety precautions and warnings in

the Instruction Manual before operating or maintaining this power tool.

Most accidents that result from power tool operation and maintenance are caused by the

failure to observe basic safety rules or precautions. An accident can often be avoided by

recognizing a potentially hazardous situation before it occurs, and by observing appropriate

safety procedures.

Basic safety precautions are outlined in the “SAFETY” section of this Instruction Manual and

in the sections which contain the operation and maintenance instructions.

Hazards that must be avoided to prevent bodily injury or machine damage are identified by

WARNINGS on the power tool and in this Instruction Manual.

Never use this power tool in a manner that has not been specifically recommended by

HITACHI, unless you first confirm that the planned use will be safe for you and others.

MEANINGS OF SIGNAL WORDS

WARNING indicates a potentially hazardous situations which, if ignored, could result in

serious personal injury.

CAUTION indicates a hazardous situations which, if ignored, could result in moderate

personal injury, or could cause machine damage.

NOTE emphasizes essential information.

English

SAFETY

INPORTANT SAFETY INSTRUCTIONS

FOR USING ALL POWER TOOLSaaaa

WARNING: Death or serious bodily injury could result from improper or unsafe use

of power tools. To avoid these risks, follow these basic safety instruc-

tions:

READ ALL INSTRUCTIONS

1. NEVER TOUCH MOVING PARTS.

Never place your hands, fingers or other body parts near the tool’s moving parts.

2. NEVER OPERATE WITHOUT ALL GUARDS IN PLACE.

Never operate this tool without all guards or safety features in place and in proper working

order. If maintenance or servicing requires the removal of a guard or safety feature, be sure

to replace the guard or safety feature before resuming operation of the tool.

3. ALWAYS WEAR EYE AND EAR PROTECTOR.

Protect yourself from flying or expelled wood chips, metal particles or other debris by

using protective goggles or equivalent eye protector. Wear ear protector to protect

yourself from excessive noise.

4. PROTECT YOURSELF AGAINST ELECTRIC SHOCK.

Prevent body contact with grounded surfaces such as pipes, radiators, ranges and

refrigeration enclosures. Never operate the tool in damp or wet locations.

5. DISCONNECT TOOLS.

Never leave the tool connected to a power source. Always disconnect the tool from its

power source before servicing, inspecting, maintaining, cleaning and before changing or

checking any parts.

6. AVOID UNINTENTIONAL STARTING.

Don’t carry the tool while it is connected to its power source. Don’t carry the tool with your

finger near the power switch. Be sure the power switch is in the “off” position before

connecting the tool to its power source.

7. STORE TOOL PROPERLY.

When not in use, the tool should be stored in a dry place. Keep out of reach of children.

Lock-out the storage area.

8. KEEP WORK AREA CLEAN.

Cluttered areas and benches invite injuries. Clear all work areas and work benches of

unnecessary tools, debris, furniture, etc.

9. CONSIDER WORK AREA ENVIRONMENT.

Don’t expose power tools to rain. Don’t use power tools in damp or wet locations. Keep

work area well lit and well ventilated.

Don’t use tool in presence of flammable liquids or gases.

Power tools produce sparks during operation. They also spark when switching ON/

OFF. Never use power tools in sites containing lacquer, paint, benzine, thinner,

gasoline, gases, adhesive agents, and other materials which are combustible or

explosive.

English

10. KEEP CHILDREN AWAY.

Do not let visitors contact tool or extension cord.

All visitors should be kept safely away from work area.

11. DON’T FORCE TOOL.

It will do the job better and safer at the rate for which it was intended.

12. USE RIGHT TOOL.

Don’t force small tool or attachment to do the job of a heavy-duty tool.

Don’t use tool for purpose not intended —for example— don’t use circular saw for cutting

tree limbs or logs.

13. DRESS PROPERLY.

Do not wear loose clothing or jewelry. They can be caught in moving parts.

Rubber gloves and non-skid footwear are recommended when working outdoors.

Wear protective hair covering to contain long hair.

14. USE FACE, DUST MASK OR RESPIRATOR IF OPERATION IS DUSTY.

All persons in the area where power tools are being operated should also wear face, dust

mask or respirator.

15. DON’T ABUSE CORD.

Never carry tool by cord or yank it to disconnect from receptacle.

Keep cord from heat, oil and sharp edges.

16. SECURE WORK.

Use clamps or a vise to hold work. It’s safer than using your hand and it frees both hands

to operate tool.

17. DON’T OVERREACH.

Keep proper footing and balance at all times.

18. MAINTAIN TOOLS WITH CARE.

Keep tools sharp and clean for better and safer performance.

Follow instructions for lubricating and changing accessories.

Inspect tool cords periodically and if damaged, have repaired by an authorized service

center. Inspect extension cords periodically and replace if damaged.

Keep handles dry, clean, and free from oil and grease.

19. REMOVE ADJUSTING KEYS AND WRENCHES.

Keys and adjusting wrenches remove from tool before turning it on.

20. OUTDOOR USE EXTENSION CORD.

When tool is used outdoors, use only extension cord intended for use outdoors and so

marked.

21. STAY ALERT.

Watch what you are doing. Use common sense. Do not operate tool when you are tired.

Tools should never be used by you if you are under the influence of alcohol, drugs or

medication that makes you drowsy.

22. CHECK DAMAGED PARTS.

Before further use of the tool, a guard or other part that is damaged should be carefully

checked to determine that it will operate properly and perform its intended function.

Check for alignment of moving parts, binding of moving parts, breakage of parts,

mounting, and any other conditions that may affect its operation.

A guard or other part that is damaged should be properly repaired or replaced by an

authorized service center unless otherwise indicated elsewhere in this Instruction

Manual.

Have defective switches replaced by the authorized service center.

Do not use tool if switch does not turn it on and off.

English

23. NEVER USE A POWER TOOL FOR APPLICATIONS OTHER THAN THOSE SPECIFIED.

Never use a power tool for applications other than those specified in the Instruction

Manual.

24. HANDLE TOOL CORRECTLY.

Operate the tool according to the instructions provided herein. Do not drop or throw the

tool. Never allow the tool to be operated by children, individuals unfamiliar with its

operation or unauthorized personnel.

25. CHECK FOR LIVE WIRES.

Avoid the risk of severe electrical shock by checking for live electrical wires that may be

buried in walls, floors or ceilings. The wires should be de-energized before work begins.

26. KEEP ALL SCREWS, BOLTS AND COVERS TIGHTLY IN PLACE.

Keep all screws, bolts, and plates tightly mounted. Check their condition periodically.

27. DO NOT USE POWER TOOLS IF THE PLASTIC HOUSING OR HANDLE IS CRACKED.

Cracks in the tool’s housing or handle can lead to electric shock. Such tools should not

be used until repaired.

28. BLADES AND ACCESSORIES MUST BE SECURELY MOUNTED TO THE TOOL.

Prevent potential injuries to youself or others. Blades, cutting implements and accessories

which have been mounted to the tool should be secure and tight.

29. KEEP MOTOR AIR VENT CLEAN.

The tool’s motor air vent must be kept clean so that air can freely flow at all times. Check

for dust build-up frequently.

30. OPERATE POWER TOOLS AT THE RATED VOLTAGE.

Operate the power tool at voltages specified on its nameplate.

If using the power tool at a higher voltage than the rated voltage, it will result in

abnormally fast motor revolution and may damage the unit and the motor may burn out.

31. NEVER USE A TOOL WHICH IS DEFECTIVE OR OPERATING ABNORMALLY.

If the tool appears to be operating unusually, making strange noises, or otherwise

appears defective, stop using it immediately and arrange for repairs by a Hitachi

authorized service center.

32. NEVER LEAVE TOOL RUNNING UNATTENDED. TURN POWER OFF.

Don’t leave tool until it comes to a complete stop.

33. CAREFULLY HANDLE POWER TOOLS.

Should a power tool be dropped or struck against hard materials inadvertently, it may be

deformed, cracked, or damaged.

34. DO NOT WIPE PLASTIC PARTS WITH SOLVENT.

Solvents such as gasoline, thinner benzine, carbon tetrachloride, and alcohol may

damage and crack plastic parts. Do not wipe them with such solvents.

Wipe plastic parts with a soft cloth lightly dampened with soapy water and dry

thoroughly.

35. USE ONLY GENUINE HITACHI REPLACEMENT PARTS.

Replacement parts not manufactured by Hitachi may void your warranty and can lead to

malfunction and resulting injuries. Genuine Hitachi parts are available from your dealer.

English

Fig. 1

IMPORTANT SAFETY INSTRUCTIONS

FOR USE OF THE HAMMER DRILL

WARNING: Death or serious bodily injury could result from improper or unsafe use

of the hammer drill. To avoid these risks, follow these basic safety

instructions:

1. NEVER touch the tool bit with bare hands after operation.

2. NEVER wear gloves made of stuff liable to roll up such as cotton, wool, cloth or string,

etc.

3. ALWAYS attach the side handle and securely grip the Hammer Drill.

4. ALWAYS wear eye and ear protectors during operation.

5. ALWAYS be careful with buried object such as an underground wiring.

Touching these active wiring or electric cable with this tool, you may receive an electric

shock.

Comfirm if there are any buried object such as electric cable within the wall, floor or

ceiling where you are going to operate here after.

6. ALWAYS set the bit rotation switch lever to the R-side when boring concrete or similar

hard materials in IMPSCT mode. (Fig. 1)

7. ALWAYS set the change lever in ROTATION mode when tightening or loosening screws.

(Fig. 2)

REPLACEMENT PARTS

When servicing use only identical replacement parts.

Repairs should be conducted only by a Hitachi authorized service center.

Fig. 2

English

POLARIZED PLUGS

To reduce the risk of electrick shock, this equipment has a polarized plug (one blade is wider

than the other).

This plug will fit in a polarized outlet only one way.

If the plug does not fit fully in the outlet, reverse the plug.

If it still does not fit, contact a qualified electrician to install the proper outlet.

Do not change the plug in any way.

USE OF EXTENSION CORD

Make sure your extension cord is in good condition. When using an extension cord, be sure

to use one heavy enough to carry the current your product will draw.

An undersized cord will cause a drop in line voltage resulting in loss of power and

overheating. Table shows the correct size to use depending on cord length and nameplate

ampere rating. If in doubt, use the next heavier gage. The smaller the gage number, the

heavier the cord.

MINIMUM GAGE FOR CORD SETS

Total Length of Cord in Feet (Meter)

0 – 25 26 – 50 51 – 100 101 – 150

(0 – 7.6) (7.9 – 15.2) (15.5 – 30.5) (30.8 – 45.7)

Ampere Rating AWG

More Not More

Than Than

0 – 618 16 16 14

6 – 10 18 16 14 12

10 – 12 16 16 14 12

12 – 16 14 12 Not Recommended

WARNING: Avoid electrical shock hazard. Never use this tool with a damaged or

frayed electrical cord or extension cord.

Inspect all electrical cords regularly. Never use in or near water or in any

environment where electric shock is possible.

English

DOUBLE INSULATION FOR SAFER OPERATION

To ensure safer operation of this power tool, HITACHI has adopted a double insulation

design. “Double insulation “ means that two physically separated insulation systems have

been used to insulate the electrically conductive materials connected to the power supply

from the outer frame handled by the operator. Therefore, either the symbol “

” or the words

“Double insulation” appear on the power tool or on the nameplate.

Although this system has no external grounding, you must still follow the normal electrical

safety precautions given in this Instruction Manual, including not using the power tool in wet

environments.

To keep the double insulation system effective, follow these precautions:

䡬 Only HITACHI AUTHORIZED SERVICE CENTER should disassemble or assemble this

power tool, and only genuine HITACHI replacement parts should be installed.

䡬 Clean the exterior of the power tool only with a soft cloth moistened with soapy water,

and dry thoroughly.

Never use solvents, gasoline or thinners on plastic components; otherwise the plastic

may dissolve.

SAVE THESE INSTRUCTIONS

AND

MAKE THEM AVAILABLE TO

OTHER USERS OF THIS TOOL!

English

OPERATION AND MAINTENANCE

NOTE:

The information contained in this Instruction Manual is designed to assist you in the safe

operation and maintenance of the power tool.

Some illustrations in this Instruction Manual may show details or attachments that differ

from those on your own power tool

NAME OF PARTS

Motor Single Phase, Series Commutator Motor

Power source Single Phase 115V AC 60 Hz

Current 5 A

Reversible Yes

No-load speed 0–2900 rpm

Drill chuck capacity 1/2" (13mm)

Steel 1/2" (13mm)

Capacity Concrete 5/8" (16mm)

Wood 1" (25mm)

Weight (Without Cord) 3.52 lbs (1.6 kg)

SPECIFICATIONS

Keyless Drill Chuck

Change lever Nameplate

Housing

Trigger Switch

Reversing

Switch

Side Handle

Depth Gauge

Fig. 3

English

ACCESSORIES

WARNING: Accessories for this power tool are mentioned in this Instruction

Manual.

The use of any other attachment or accessory can be dangerous and

could cause injury or mechanical damage.

STANDARD ACCESSORIES

(1) Case (Code No. 315999) ...................................................................................................... 1

(2) Side Handle (Code No. 303659) .......................................................................................... 1

(3) Depth Gauge (Code No. 310331) ........................................................................................ 1

OPTIONAL ACCESSORIES …………… sold separately

(1) Drill bit for concrete and stone

Bit Dia. Overall Code No. Bit Dia. Overall Code No. Bit Dia. Overall Code No.

Length Length Length

1/4" 4'’

931851

3/8" 4-3/4"

931854

9/16" 6-5/16"

931776

(6.5mm) (100mm) (10mm) (120mm) (14.3mm) (160mm)

5/16" 4"

931852

15/32" 4-3/4"

971704

5/8" 6-5/16"

931670

(8mm) (100mm) (12mm) (120mm) (16mm) (160mm)

0.37" 4-3/4"

931853

1/2" 6-5/16"

931855

(9.5mm) (120mm) (13mm) (160mm)

NOTE:

Accessories are subject to change without any obligation on the part of the HITACHI.

(2) Phillips bit

(3) Slotted bit

Bit No. Screw Size Length Code No.

No. 2

1/8"-3/16" 2-3/4"

955654

(3mm-5mm) (70mm)

No. 3

1/4"-5/16" 2-3/4"

955655

(6mm-8mm) (70mm)

a Screw Size Code No.

1/32" 5/32"

955659

(0.8mm) (4mm)

3/64" 3/16"-1/4"

955674

(1mm) (5mm-6mm)

Bit No.

English

APPLICATIONS

䡬 By combined actions of ROTATION and IMPACT:

Boring holes in hard surfaces (concrete, marble, granite, tiles, etc.)

䡬 By ROTATIONAL action:

Boring holes in metal, wood and plastic.

Tightening wood screws.

PRIOR TO OPERATION

1. Power source

Ensure that the power source to be utilized conforms to the power source requirements

specified on the product nameplate.

2. Power switch

Ensure that the switch is in the OFF position. If the plug is connected to a receptacle while

the switch is in the ON position, the power tool will start operating immediately and can

cause serious injury.

3. Extension cord

When the work area is far away from the power source, use an extension cord of sufficient

thickness and rated capacity. The extension cord should be kept as short as practicable.

WARNING: Damaged cord must be replaced or repaired.

4. Check the receptacle

If the receptacle only loosely accepts the plug, the receptacle must be repaired. Contact

a licensed electrician to make appropriate repairs.

If such a fautly receptacle is used, it may cause overheating, resulting in a serious hazard.

5. Confirming condition of the environment:

Confirm that the work site is placed under appropriate conditions conforming to

prescribed precautions.

6. Side handle attachment

Attach the side handle to the mounting part.

Rotate the side handle grip in a clockwise direction to secure it.

Set the side handle to a position that is suited to the operation and then securely tighten

the side handle grip.

7. Selecting the appropriate drill bit:

䡬 When boring concrete or stone

Use the drill bits specified in the Optional Accessories.

䡬 When boring metal or plastic

Use an ordinary metalworking drill bit.

Sizes range from a minimum of 1/16" (2mm) to chuck maximam capacity.

䡬 When boring wood

Use an ordinary woodworking drill bit.

However, when drilling 1/4" (6.5 mm) or smaller holes, use a metalworking drill bit.

English

8. Selecting the driver bit

Screw heads or bits will be damaged unless a bit appropriate for the screw diameter is

employed to drive in the screws.

9. Mounting and dismounting of the bit.

For keyless chuck

(1) Mounting the bit

After inserting a driver bit, etc. into the keyless drill chuck, firmly grasp the ring and

tighten the sleeve by turning it toward the right (in the clockwise direction as viewed from

the front). (See Fig. 4)

䡬 If the sleeve becomes loose during operation, tighten it further. The tightening force

becomes stronger when the sleeve is tightened.

(2) Dismounting the bit

Firmly grasp the ring and loosen the sleeve by turning it toward the left (in the

counterclockwise direction as viewed from the front). (See Fig. 4)

NOTE:

When the sleeve does not become loose any further, fix the side handle to the sleeve.

Then, strike the grip of the side handle to the left in order to loosen the sleeve, while

holding the ring by hand. (Fig. 5)

Fig. 5Fig. 4

Tighten

Loosen

SleeveRing

Sleeve

Side

Handle

Ring

Loosen

CAUTION

Do not fix the side handle to the ring of the keyless chuck because of a risk that

doing so may damage the ring.

For Drill chuck with chuck wrench

Fit the drill bit into the chuck and use the

chuck wrench to secure it, tightening the

chuck by each of the three holes in turn.

(Fig. 6)

LoosenTighten

Chuck

wrench

Fig. 6

English

10.Confirm the direction of bit rotation

(Fig. 7)

The bit rotates clockwise (viewed from

the rear side) by pushing the R-side of the

reversing switch lever.

The L-side of the lever is pushed to turn

the bit counterclockwise.

CAUTION

䢇 Never change the direction of bit rotation while operating. Turn the power switch OFF

before changing the direction of bit rotation: otherwise, burning of the motor will result.

䢇 Always use the hammer drill with clockwise rotation, when using it as an hammer drill.

11.IMPACT to ROTATION changeover

(Fig. 8)

The Hammer Drill can be switched from

IMPACT (impact plus rotation) to

ROTATION (rotation only) by rotating the

change lever (Fig. 1). When boring

concrete, stone, tile or similar materials,

sliding the change lever to IMPACT side.

The drill head impacts against the material

while continuing to rotate.

When boring metal, wood or plastic or

tightening, sliding the change lever to

ROTATION side. The drill rotates as an

ordinary electric drill.

CAUTION

Do not use the Hammer Drill in the IMPACT function if the material can be bored by

rotation only. Such action will not only reduce drill efficiency, but may also damage the

drill tip.

HOW TO USE

1. Speed adjustment and switch operation

䡬 The drill speed can be adjusted from 0 through full speed by regulating the trigger-

squeezing force. The more the trigger is squeezed, the faster the drill rotates. When the

trigger is squeezed fully, the speed is the maximum.

Turn the adjust knob clockwise for higher speed and coutnerclockwise for lower speed.

(Rotate the adjust knob approximately 2-2/3 turns.) (Fig. 9)

Change lever

ROTATION

ROTATION+IMPACT

Fig. 8

Counter-

clockwise

Clockwise

Fig. 7

English

䡬 Pulling the trigger switch and pushing

the stopper, it keeps the switched-on con-

dition which is convenient for continuous

running. When switching off, the stopper

can be disconnected by pulling the trig-

ger again.

2. When using as a Drill or a Hammer Drill

(1) Pressing force of the drill

You cannot drill holes more quickly even if you press the drill with a stronger force than

necessary. It not only damages tip of drill bits and decreases the efficiency of operation,

but also shortens the life of the drill.

(2) In case of penetrating holes

Drill bits can be broken when the material being drilled is penetrated. It is important to

decrease pressing force just before penetrating.

CAUTION :

In continuous operation, conduct no-load operation for five seconds after

completing a drilling job.

WARNING: When a thick drill bit is used, your arm is subjected to larger reaction

force. Be careful not to be moved by the reaction force. For this,

establish a foothold, hold the unit tightly with both hands perpendicularly

to the material being drilled.

3. When driving wood screws

(1) Selecting a suitable driver bit

Employ plus-head screws, if possible, since the driver bit easily slips off the heads of

minus-head screws.

(2) Driving in wood screws

䡬 Prior to driving in wood screws, make pilot holes suitable for them in the wooden board.

Apply the bit to the screw head grooves and gently drive the screws into the holes.

䡬 After rotating the driver bit at low speed for a while until a wood screw is partly driven

into the wood, squeeze the trigger more strongly to obtain the optimum driving force.

NOTE:

Exercise care in preparing a pilot hole suitable for the wood screw taking the hardness

of the wood into consideration. Should the hole the excessively small or shallow,

requiring much power to drive the screw into it, the thread of the wood screw may

sometimes be damaged.

Stopper

Low Speed

Adjust Knob

High Speed

Fig. 9

English

MAINTENANCE AND INSPECTION

WARNING: Be sure to switch power OFF and disconnect the plug from the receptacle

during maintenance and inspection.

1. Inspecting the driver bit

Since continued use of a worn driver bit will damage screw heads, replace the driver bit

as soon as excessive wear is noticed.

2. Inspection the drill bit

Continued use of a worn and/or damaged drill bit will result in reduced drilling efficiency

and may seriously overload the drill motor. Inspect the drill bit frequently and replace it

as necessary.

3. Inspecting the mounting screws

Regularly inspect all mounting screws and ensure that they are properly tightened.

Should any of the screws be loosened, retighten them immediately.

WARNING: Using this hammer drill with loosen screws is extremely dangerous.

4. Maintenance of the motor

The motor unit winding is the very “heart”’ of the power tool. Exercise due care to ensure

the winding does not become damaged and/or wet with oil or water.

5. Inspecting the carbon brushes

For your continued safety and electrical shock protection, carbon brush inspection and

replacement on this tool should ONLY be performed by a HITACHI AUTHORIZED

SERVICE CENTER.

SERVICE AND REPAIRS

All quality power tools will eventually require servicing or replacement of parts because of

wear from normal use. To assure that only authorized replacement parts will be used, all

service and repairs must be performed by a HITACHI AUTHORIZED SERVICE CENTER,

ONLY.

NOTE:

Specifications are subject to change without any obligation on the part of the HITACHI.

Français

INFORMATIONS IMPORTANTES

Lire et comprendre toutes les instructions de fonctionnement, les précautions de sécurité et

les avertissements dans ce mode d’emploi avant d’utiliser ou d’entretenir cet outil motorisé.

La plupart des accidents causés lors de l’utilisation ou de l’entretien de l’outil motorisé

proviennent d’un non respect des règles ou précautions de base de sécurité. Un accident

peut la plupart du temps être évité si l’on reconnaît une situation de danger potentiel avant

qu’elle ne se produise, et en observant les procédures de sécurité appropriées.

Les précautions de base de sécurité sont mises en évidence dans la section “SECURITE” de

ce mode d’emploi et dans les sections qui contiennent les instructions de fonctionnement

et d’entretien.

Les dangers qui doivent être évités pour prévenir des blessures corporelles ou un

endommagement de la machine sont identifiés par AVERTISSEMENTS sur l’outil motorisé

et dans ce mode d’emploi.

Ne jamais utiliser cet outil motorisé d ’une manière qui n’est pas spécifiquement recommandée

par HITACHI sans avoir d’abord vérifié que l’utilisation prévue est sans danger pour vous et

les autres.

SIGNIFICATION DES MOTS D’AVERTISSEMENT

AVERTISSEMENT indique des situations potentiellement dangereuses qui, si elles sont

ignorées, pourraient entraîner de sérieuses blessures personnelles.

PRECAUTION indique des situations dangereuses qui, si elles sont ignorées, pourrait

entraîner de légères blessures personnelles ou endommager la machine.

REMARQUE met en relief des informations essentielles.

Français

SECURITE

CONSIGNES DE SECURITE IMPORTANTES POUR IIIII

L’UTILISATION DE TOUS LES OUTILS ELECTRIQUES

AVERTISSEMENT:Une utilisation incorrecte ou dangereuse des outils électriques

peut entraîner la mort ou des blessures graves.

LIRE TOUT CE MODE D’EMPLOI.

1. NE JAMAIS TOUCHER LES PARTIES MOBILES.

Ne jamais placer ses mains, ses doigts ou toute autre partie de son corps près des parties

mobiles de l’outil.

2. NE JAMAIS UTILISER L’OUTIL SANS QUE TOUS LES DISPOSITIFS DE SECURITE NE

SOIENT EN PLACE.

Ne jamais faire fonctionner cet outil sans que tous les dispositifs et caractéristiques de

sécurité ne soient en place et en état de fonctionnement. Si un entretien ou une réparation

nécessite le retrait d’un dispositif ou d’une caractéristique de sécurité, s’assurer de bien

remettre en place le dispositif ou la caractéristique de sécurité avant de recommencer à

utiliser l’outil.

3. TOUJOURS SE PROTEGER LES YEUX ET LES OREILLES.

Pour se protéger des projections de copeaux de bois, particules métalliques ou autres

débris, porter des lunettes de protection ou un masque pour les yeux. Porter des

protections anti-bruit pour se protéger du bruit.

4. SE PROTEGER CONTRE LES DECHARGES ELECTRIQUES.

Empêcher tout contact du corps avec les surfaces mises à la terre, par exemple tuyaux,

radiateurs, plaques de cuisson et enceintes de réfrigération. Ne jamais faire fonctionner

l’outil dans un endroit humide ou mouillé.

5. DEBRANCHER LES OUTILS.

Ne jamais laisser l’outil branché dans une source d’alimentation. Toujours débrancher

l’outil de la source d’alimentation avant tout travail de réparation, d’inspection, d’entretien,

de nettoyage, de remplacement ou de vérification des pièces.

6. EVITER TOUTE MISE EN MARCHE INOPINEE.

Ne pas transporter l’outil pendant qu’il est raccordé à la source d’alimentation. Ne pas

transporter l’outil avec le doigt près de l’interrupteur d’alimentation. Bien s’assurer que

l’interrupteur d’alimentation se trouve sur la position “OFF” (arrêt) avant de raccorder

l’outil à la source d’alimentation.

7. REMISER L’OUTIL CORRECTEMENT.

Lorsqu’on ne se sert pas de l’outil, le remiser dans un endroit sec. Veiller à ce qu’il soit

hors d’atteinte des enfants. Fermer le local de remisage à clé.

8. MAINTENIR L’AIRE DE TRAVAIL PROPRE.

Les aires de travail et les établis encombrés favorisent les accidents. Débarrasser l’aire

de travail et les établis des outils inutiles, débris, meubles, etc.

Français

9. CONSIDERER L’ENVIRONNEMENT DE L’AIRE DE TRAVAIL.

Ne pas exposer les outils à la pluie. Ne pas les utiliser dans un endroit humide ou mouillé.

Veiller à ce que l’aire de travail soit bien éclairée et bien aérée.

Ne pas utiliser l’outil en présence de liquides ou de gaz inflammables.

Les outils projettent des étincelles pendant qu’ils fonctionnent. Ne jamais utiliser les

outils dans un lieu renfermant de la laque, de la peinture, du diluant, de l’essence, des

gaz, des produits adhésifs ni aucun autre matériau combustible ou explosif.

10. ELOIGNER LES ENFANTS.

Ne pas laisser les visiteurs toucher l’outil ou le cordon de rallonge.

Tous les visiteurs devront être suffisamment éloignés de l’aire de travail.

11. NE PAS FORCER L’OUTIL.

Il effectuera le travail le meilleur et avec la sécurité maximale au régime pour lequel il a

été conçu.

12. UTILISER L’OUTIL CORRECT

Ne pas forcer sur un petit outil ou accessoire pour faire le travail d’un outil de grande

puissance. Ne pas utiliser un outil pour un usage pour lequel il n’a pas été prévu: par

exemple, ne pas utiliser une scie circulaire pour couper des branches d’arbre ou des

bûches.

13. SE VETIR CORRECTEMENT.

Ne pas porter de vêtements lâches ni de bijoux. Ils pourraient se prendre dans les pièces

en mouvement. Il est recommandé de porter des gants en caoutchouc et des chaussures

anti-glissantes lors d’un travail à l’extérieur.

Porter un couvre-chef qui recouvre les cheveux longs.

14. PORTER UN MASQUE, UN MASQUE ANTI-POUSSIERE OU UN APPAREIL RESPIRATOIRE

SI LE TRAVAIL DOIT DEGAGER DE LA POUSSIERE.

Toutes les personnes présentes sur l’aire de travail devront également porter un masque,

un masque anti-poussière ou un appareil respiratoire.

15. NE PAS MALTRAITER LE CORDON.

Ne jamais transporter l’outil par le cordon ni tirer brusquement sur le cordon pour le

débrancher.

Eloigner le cordon de la chaleur, de la graisse et des surfaces tranchantes.

16. FIXER LA PIECE.

Utiliser des dispositifs de serrage ou un étau pour tenir la pièce. Cela sera plus sûr que

de tenir la pièce à la main et libérera les deux mains pour le travail.

17. NE PAS TROP SE PENCHER.

Garder une bonne assise et un bon équilibre à tout moment.

18. ENTRETENIR LES OUTILS AVEC SOIN.

Maintenir les outils aiguisés et propres pour optimiser le travail et la sécurité.

Suivre les instructions de graissage et de remplacement des accessoires.

Vérifier périodiquement les cordons d’outil et les faire réparer par un centre de réparation

agréé s ’ils sont endommagés. Vérifier périodiquement les cordons de rallonge et les faire

remplacer s’ils sont endommagés. Maintenir les poignées sèches et propres, et enlever

toute graisse et toute huile dessus.

19. RETIRER LES CLAVETTES DE REGLAGE ET LES CLES.

Les clés et les clavettes de réglage devront être retirées de l’outil avant de sa mise en

marche.

Français

20. CORDONS DE RALLONGE POUR UTILISATION A L’EXTERIEUR.

Si l’outil doit être utilisé dehors, utiliser exclusivement des cordons de rallonge conçus

pour un usage extérieur et marqués à cet effet.

21. RESTER SUR SES GARDES.

Bien faire attention à ce que l’on fait. Faire preuve de bon sens. Ne pas utiliser l’outil

lorsqu’on est fatigué.

Ne jamais utiliser l’outil si l’on est sous l’influence d’alcool, de drogues ou de médicaments

qui rendent somnolent.

22. VERIFIER S’IL Y A DES PIECES ENDOMMAGEES.

Avant de continuer à utiliser l’outil, inspecter attentivement les protections ou autres

pièces endommagées pour voir si l’outil pourra fonctionner correctement et effectuer le

travail pour lequel il est conçu. Vérifier l’alignement et le couplage des pièces mobiles,

le voilage des pièces mobiles, la présence de pièces cassées, le montage, et toute autre

condition susceptible d’affecter le bon fonctionnement.

Si une protection ou une pièce est endommagée, la faire réparer ou remplacer par un

service après-vente agréé, sauf spécification contraire dans ce mode d’emploi.

Faire remplacer les interrupteurs défectueux par un centre de réparation agréé.

Ne pas utiliser l’outil si l’interrupteur ne fonctionne pas.

23. NE JAMAIS UTILISER UN OUTIL MOTORISE POUR DES APPLICATIONS AUTRES QUE

CELLES SPECIFIEES.

Ne jamais utiliser un outil motorisé pour des applications autres que celles spécifiées

dans le mode d’emploi.

24. MANIPULER L’OUTIL CORRECTEMENT

Utiliser l’outil de la façon indiquée dans ce mode d’emploi. Ne pas laisser tomber ou

lancer l’outil. Ne jamais permettre que l’outil soit utilisé par des enfants, des personnes

non familiarisées avec son fonctionnement ou un personnel non autorisé.

25. VERIFIER S’IL Y A DES FILS SOUS TENSION.

Pour éviter tout risque de choc électrique grave, vérifier s’il y a des fils électriques sous

tension encastrés dans le mur, le plancher ou le plafond. Couper l’alimentation des fils

avant le travail.

26. MAINTENIR TOUTES LES VIS, TOUS LES BOULONS ET LES COUVERCLES FERMEMENT

EN PLACE.

Maintenir toutes les vis, tous les boulons et les couvercles fermement montés. Vérifier

leurs conditions périodiquement.

27. NE PAS UTILISER LES OUTILS MOTORISES SI LE REVETEMENT DE PLASTIQUE OU LA

POIGNEE EST FENDU.

Des fentes dans le revêtement ou la poignée peuvent entraîner une électrocution. De tels

outils ne doivent pas être utilisés avant d’être réparé.

28.LES LAMES ET LES ACCESSOIRES DOIVENT ETRE FERMEMENT MONTES

SUR L’OUTIL.

Eviter les blessures potentielles personnelles et aux autres. Les lames, les instruments

de coupe et les accessoires qui ont été montés sur l’outil doivent être fixés et serrés

fermement.

29. GARDER PROPRES LES EVENTS D’AIR DU MOTEUR

Les évents d’air du moteur doivent être maintenus propres de façon que l’air puisse

circuler librement tout le temps. Vérifier les accumulations de poussière fréquemment.

Page is loading ...

Hitachi FDV 16VB Instruction Manual And Safety Instructions

Brand: Hitachi

Model: FDV 16VB

Category: Power tools

Type: Instruction Manual And Safety Instructions

Download PDF

report

in other languages

français: Hitachi FDV 16VB
español: Hitachi FDV 16VB

Hitachi FDV 16VB Instruction Manual And Safety Instructions

Hitachi FDV 16VB Instruction Manual And Safety Instructions

in other languages

Related papers

Other documents