ACEK9 H-RBM Install Manual

Brand: ACEK9

Model: H-RBM

Type: Install Manual

Pager Install Manual H-RBM

New Systems with protective relay module

(instructions for older units on following pages)

Pager Install Manual H-RBM

Systems with protective relay module

Installation Considerations.

 The Pager transmits radio signals and should be mounted at least

6 inches from other electronic devices.

 Mount in a dry location.

Step 1 Install Pager Antenna, Follow instructions included with antenna.

Step 2 Plug Antenna into the Pager Transmitter socket marked "ANTENNA".

Socket marked radio is not used.

Step 3 Set antenna switch to “B” for external mounted mast style antennas.

Step 4 Unplug the 24 Pin Connector from the Protective Relay Module (PRM).

Insert Gray Pager terminal wire into Pin 4 location.

Insert Black Pager terminal wire into Pin 3 location.

Insert Red/Gray Pager terminal wire into Pin 15 location.

Step 4 Attach the Pager Transmitter's Black wire to PRM's Black terminal

wire.

Step 5 Connect the Pager's Red power wire to PRM's Red/Gray terminal

wire.

Step 6 Connect the Pager’s Blue wire to the PRM's Gray wire.

Step 7 Install 2 AAA batteries and program receiver

Step 8 The Pager Receiver comes programmed to match the receiver. If an

additional receiver needs programming follow the following steps in the back of

this manual.

Step 9 Test the Pager System with the Heat Alarm. Run a system Test to verify

transmission (See manual of your AceK9.Com product)

Step 10 Secure the Pager Transmitter in a dry location.

Pager Install Manual

H-RBM

With AceK9 Alarms With Options cables

Intelabox's without X Serial Numbers and

AceK9 alarms built after 2011 AceK9 alarm Built Prior to

2011 will not function properly with this pager.

Installation Considerations.

1. The Pager transmits radio signals and should be mounted at least

six inches from other electronic devices.

2. Mount in a dry location.

Step 1 Install Pager Antenna, Follow instructions included with antenna.

Step 2 Plug Antenna into the Pager Transmitter socket marked "ANTENNA".

Socket marked radio is not used.

Step 3 Set antenna switch to “B” for external mounted mast style antennas.

Step 4 Attach the Pager Transmitter's Ground wires to a good Ground.

Step 5 Connect the Pager Transmitter's red power wire to a Battery Hot point. It

is important that the power to the Transmitter is a "Hot at all times" power point

because it transmits each time power is applied.

Step 6 Connect the Pager Transmitter’s Blue Wire

For K9 Hot-N-Pop Pro or K9 Heat Alarm Pro

Connect to the Black/Green (Fan)

trigger wire to activate the Pager. NOTE If the fan kit is being utilized, the fan

and the Pager will share the black/green wire.

For K9 Heat Alarm

Connect to the Green Wire

(Latched)

Step 7 Install 2 AAA batteries in the receiver.

Step 8 PROGRAM Receiver to learn Transmitter code

(IF NEEDED)

Step 9 After programming is completed, Test the Pager System with the

Heat Alarm. Run a system test to verify transmission (See manual of your

AceK9.Com product)

Step 10 Secure the Pager Transmitter in a dry location.

Contact AceK9.com if you are installing a pager on a system built before 2011

Blank Page

Programming Replacement Receivers

ACEK9 H-RBM Install Manual

Brand: ACEK9

Model: H-RBM

Type: Install Manual

Download PDF

report

ACEK9 H-RBM Install Manual

ACEK9 H-RBM Install Manual

Other documents