ELK ELK-M1PR Operating instructions

Brand: ELK

Model: ELK-M1PR

Type: Operating instructions

ELK ELK-M1PR is a plug-in accessory that permits touchless reading of M1PRC prox cards and M1PRF prox fobs by a M1KP Keypad. It provides virtually the same capabilities as a user code, i.e., arm, disarm, access, etc. Ideal for higher security installations and as an alternative to remembering PIN codes.

828-397-4200 Voice

828-397-4415 Fax

http://www.elkproducts.com

email: [email protected]

PO Box 100 • Hwy. 70W • Hildebran, NC 28637 • USA

Mini Prox Reader

ELK-M1PR

APPLICATION:

The ELK-M1PR is a plug-in accessory that

permits touchless reading of M1PRC prox cards

and M1PRF prox fobs by a M1KP Keypad. It

provides virtually the same capabilities as a user

code, i.e., arm, disarm, access, etc. Ideal for

higher security installations and as an alternative

to remembering PIN codes.

FEATURES:

•Simple Plug-in Installation

•Compatible with Clamshell Style (Credit

Card size) Proximity Cards (ELK-M1PRC)

•Compatible with Keychain Style Proximity

Fobs (ELK-M1PRF)

•Low Current Draw

•Substitutes for User Code Pin Entry

SPECIFICATIONS:

•Reader Format: 26 bit Wiegand

•5 Pin Plug-in Connector

•Operating Voltage: 5 VDC from Keypad

•Current Draw: ~20 mA.

•Size: 1.875 W x 1" H x .375 D

Features or Specifications subject to change without notice.

CARDS AND FOBS (ordered separately)

ELK-M1PRC

•Pack of 10, White clam shell style prox cards

•Size: 2 1/8" L x 3 3/8" H x 3/16" T

•ELK-M1PRF

•Pack of 10, Black keyring fobs

•Size: 2 1/8" L x 1 1/4" H x 1/4" T

07/04

ENROLLING PROX CARDS AND FOBS

Each prox card/fob must be enrolled into a User

Code location, using the same procedures that

are used to add/change User Code PINs.

1. On the Keypad, press the center ELK key.

2. Press 6 to jump directly to Menu 06 - Change

User Codes OR Use the UP or DOWN arrow

keys to scroll to the menu.

3. Press the RIGHT arrow key to select Menu 6.

Enter a Master user code (PIN) to gain

access to this menu.

4. Use the UP or DOWN arrow keys to scroll to

the User Code location (001 to 099) where

the Prox card/fob is to be enrolled. OR enter

the three digit number, i.e., 050 for User 50.

5. Select CHG by pressing the RIGHT arrow key.

6. The keypad will display the existing 4 or 6

digit code that is programmed for this user

along with any programmed name.

7. Place a new (not previously enrolled) prox

card/fob near the Keypad's right speaker grill,

just below the Stay key. The ideal read range

is approximately 1/8" to 3/8" from the front

surface. The clam-shell type prox cards

generally have a better read range than fobs.

Sometimes the read range is 3/8" or more.

8. If the keypad accepts the new prox card/fob, it

will beep 3 times and display a 12 digit code,

which is part of the ID stored in the card/fob.

If the keypad rejects the prox card/fob, it will

produce a low error tone and display:

Code Not Authorized, Redo

The reject error may be caused by:

A. The card or fob has already been enrolled

(the M1 does not allow duplicate codes)

B. The facility code stored in the prox card/fob

does not match the ELK facility code. The

M1PR Reader can only read cards/fobs which

have the matching facility code.

9. After a prox card/fob has been enrolled into a

user code location, its capabilities are set by

the User Code Options found in Menu 02 of

the M1 Installer Level Programming. The

most common of these options are:

- Arm the M1 Control.

- Disarm the M1 Control.

- Access - Trip output to de-energize a lock **

** The activation assignment for M1 Outputs

requires the Whenever/And/Then Rules

programming of the Elk-RP Software.

The following example is a rule to activate

Output 003 for 10 seconds when a valid prox

card/fob (with Access Option enabled) is

presented at Keypad 01. The output could be

used to break or make power to a door strike.

WHENEVER Keypad 01 Access is Activated

THEN Turn On Output 003 for 10 seconds.

Mini Prox Reader

ELK-M1PR

for M1KP Keypad

Installation Instructions on Inside

INSTALLATION OF OPTIONAL ELK-M1PR INTERNAL PROXIMITY CARD READER

1. Turn Off the M1 Master Power Switch.

2. Remove the M1KP Keypad from its mounting plate, disconnect the 6 pin data bus cable, and place

face down on a soft surface.

3. Locate the 1" mounting hole in the lower left corner and the 5 pin male connector marked J2 to the

right of the mounting hole.

4. Position the M1PR in the 1" mounting hole with its 5 wire female cable facing towards connector J2.

5. Gently lift up on the 5 wire cable, then bend the white plug down to form a slight arch in the wires.

SEE DETAIL A. This will shorten the cable enough that it can be plugged into connector J2.

6. Reconnect the 6 pin data bus cable to connector J1 and install the keypad onto its mounting plate.

7. Turn On the M1 Master Power Switch. Refer to the instructions for enrolling cards or fobs.

ELK-M1KP LCD Keypad

ELK-M1PR

Back (Circuit) Side of Keypad

Six (6) conductor plug-in data bus cable

- 4 wires to the M1 Control

- 1 wire is an optional zone input

- 1 wire is a an optional output).

Built-in Temperature Sensor If the Keypad local temperature

reads too high after installation of the M1PR Mini Prox Reader, it

may be necessary to adjust the keypad temperature reading to

compensate for the added heat produced by the M1PR. Refer to

the M1KP Instructions or contact ELK Technical Support.

ELK-M1PR

Bend (arch) the 5 wires from the M1PR wiring plug as

shown. This provides space between the plug and the

connector (J2) so that they may be attached.

Connector

M1PR Wiring Plug

Detail A

An external Prox Reader (26 bit Wiegand compatible) from another

manufacturer may be connected to the ELK-M1KP Keypad in place of the

internal ELK-M1PR Mini Prox Reader. This requires an optional ELK-WO35A

Cable Assembly. Splice wires as indicated, then plug cable into connector J2.

White

Red

Black

Green

Brown Wire - Insulate (No Connection)

White Red

Black

Green

Brown

ELK-WO35A Cable Assembly

Detail C

External

Prox Reader

(26 bit

Wiegand)

from other

Manufacturer

Note: Earlier version keypads do

not have the newer (white)

polarized J2 jack. For these type

keypads; the small polarizing tabs

need to be cut off so the

connector will fit onto the J2 jack.

ELK-M1PR

Detail B

ELK ELK-M1PR Operating instructions

ELK ELK-M1PR Operating instructions

ELK ELK-M1PR Operating instructions

Related papers

Other documents