Safescan 2210 / 2250 User manual

Brand: Safescan

Model: 2210 / 2250

Category: Money counting machines

Type: User manual

User Manual

English

2210 / 2250

Banknote Counters

More info, articles, tutorials and videos support.safescan.com

English

Introduction

Thank you for purchasing a Safescan 2200-series banknote

counter. This user manual will help you to get started with your

Safescan banknote counter and describes the setup and operating

procedures. We recommend that before using the device you

carefully read these operating instructions.

Package contents

The retail box contains the following items:

- Safescan 2210 / 2250 Banknote Counter

- Power cord(s)*

- Maintenance kit

- User Manual

Click here to open a printable version of the manual

in the selected language.

Print version

More info, articles, tutorials and videos support.safescan.com 3

English

Product

1. Hopper with adjustable

guides

2. Front panel (display / buttons)

3. Stacker

4. Power connection

5. On/Off switch

6. Hopper adjustment wheel

7. RJ12 port for external display

connection

Front

Back

More info, articles, tutorials and videos support.safescan.com

English

8. Power cord(s)*

9. Maintenance kit

* Depending on model /

country specication

Available accessories

Safescan Cleaning Cards for banknote

counters (pack of 15 cards), partnumber

152-0663.

See www.safescan.com for details.

More info, articles, tutorials and videos support.safescan.com 5

English

Safescan 2210 / 2250: features

Banknote feature detection

features

UV and MG

features

SIZE

(height)

Safescan

2210 • — — •

Safescan

2250 ••••

More info, articles, tutorials and videos support.safescan.com

English

Buttons and operation

4 7 83 51 12 2

AUTO

2250

2210

Short press Long press (3 sec)

1. Start counting / Conrm

sensitivity level selection

Select automatic or manual

start

2. Clear the number of counted

banknotes

Clear the number of counted

banknotes

3. Add function on/off Enter thickness sensitivity

adjustment menu

4. Increase input value by 1

5. Decrease input value by 1 Enable/disable size detection

(valid for rmware version D08

/ U08 or higher)

6. UV feature detection on/off Enter UV sensitivity level

adjustment menu

7. Safescan 2210: Select auto

or manual start

Safescan 2250: MG feature

detection on/off

Enter MG sensitivity level

adjustment menu (Safescan

2250)

8. Batch function on/off / set

batch number

Enter banknote height

sensitivity level adjustment

More info, articles, tutorials and videos support.safescan.com 7

English

Getting started

1. Place the device on a at and

stable surface.

2. Connect the banknote counter

to the mains outlet using the

supplied power cord.

More info, articles, tutorials and videos support.safescan.com

English

Ready for counting

The machine is now ready for basic counting. More advanced

settings are described in the next chapters of this manual.

3. Switch on the banknote

counter by pushing the power

switch at the back in the “1”

position.

4. Default banknote feature

detection settings: Safescan

2210: UV, 2250: UV and MG.

These can be switched on or

off by pressing the UV and/or

MG* button.

(* Safescan 2250 only)

More info, articles, tutorials and videos support.safescan.com 9

English

Counting banknotes

1. AUTO START / MANUAL START. Default setting is “AUTO” the

machine will start counting once banknotes have been placed

in the hopper. You can choose whether you want the device to

start counting automatically or manually (counting starts after

pressing the [START] button).

Safescan 2210: press the AUTO button to activate/de-activate the

auto start function. This will be shown in the display.

AUTO

2250

2210

Safescan 2250: press the START button for 3 seconds to activate/

de-activate the auto start function.

AUTO

2250

2210

3SEC

More info, articles, tutorials and videos support.safescan.com

English

Please note The banknotes have to be sorted per denomination

before counting.

2. Start counting banknotes by placing the banknotes in the center

of the hopper as shown in g. 1, then ip them backwards as

shown in g. 2. Use the hopper guides to keep the banknotes

centered.

1 2

More info, articles, tutorials and videos support.safescan.com 11

English

4. Once you count a second stack of banknotes or re-count the

rst stack, the number of notes of the previous count will be

shown under CHECK in the display. To set this quantity to zero,

press CLR.

AUTO

3. The number of banknotes is shown clearly after the count has

nished.

AUTO

More info, articles, tutorials and videos support.safescan.com

English

Once the machine detects a problem with a banknote, it will stop

counting and show a clear message including the type of issue.

The error concerns the last counted banknote in the stacker.

The following messages are possible:

There is a problem with the UV

features.

There is a problem with the

magnetic features (Safescan

2250 only)

Error messages during a count

A banknote with a different

height than the rst counted

banknote has been detected

(minimum difference 5mm)

A banknote with a different

thickness has been detected,

or 2 banknotes may be stuck

together (“double note detection”)

More info, articles, tutorials and videos support.safescan.com 13

English

Remove the suspect banknote - this is the last counted banknote in

the stacker - and press START to continue counting.

For more information and details please see chapter

“Troubleshooting”

The banknote has gone through

the machine in a skewed

position (not fed straight inside

the machine).

A banknote with a different

width than the rst counted

banknote has been detected

(“half note detection”)

More info, articles, tutorials and videos support.safescan.com

English

AUTO

1. ADD

The ADD function enables you to count cumulatively. Once you

remove a stack of counted banknotes and add a new stack,

these quantities will be added to the total count. The function

can be activated by pressing the ADD button. The indicator in

the display will light up.

2. BATCH

The BATCH function enables you to create equal stacks of a

pre-set number of banknotes. The counter will stop counting

when the set batch number has been reached. You can set the

batch number as follows:

2.1. Press the BATCH button to activate the function. The indicator

in the display lights up, including 2 blinking arrows.

Add and batch functions

More info, articles, tutorials and videos support.safescan.com 15

English

AUTO

2.2. Navigate through the pre-set batch numbers by pressing the

BATCH button again. The sequence is: 100 > 50 > 20 > 10 >

Batch off.

2.3. Use the arrow keys to increase or decrease the batch number

by 1 piece, starting from the number that is shown. When the

display shows ‘100’, you can go to 101, 102 etc. by pressing

and to 99, 98 etc. by pressing

2.4. Conrm the batch number by pressing the START key. After

this, the set batch number will remain visible in the screen.

More info, articles, tutorials and videos support.safescan.com

English

Your banknote counter has already been pre-congured with

the optimal counterfeit detection settings. On rare occasions it

could be required to manually adjust the sensitivty of one or more

counterfeit detection settings.

Note: only adjust these settings when being advised to do so by

a Safescan technical expert.

Adjusting counterfeit detection settings

3SEC

The sensitivity of the detection features can be adjusted via the

menu. The following settings can be made:

1. UV

Pressing the UV button for 3 seconds will activate the UV sensitivity

level menu. The default level is shown, including 2 blinking arrows.

See (5) for adjustment procedure.

More info, articles, tutorials and videos support.safescan.com 17

English

3. Height

Pressing the BATCH button for 3 seconds will activate the HEIGHT

sensitivity level menu. The default level is shown, including 2

blinking arrows. See (5) for adjustment procedure.

3SEC

2. MG

Safescan 2250 only: Pressing the MG button for 3 seconds will

activate the MG sensitivity level menu. The default level is shown,

including 2 blinking arrows. See (5) for adjustment procedure.

3SEC

More info, articles, tutorials and videos support.safescan.com

English

4. Thickness

Press the ADD button for 3 seconds to activate the THICKNESS

sensitivity level menu. The default level is shown, including 2

blinking arrows. See (5) for adjustment procedure.

5. Level adjustment

Adjust the sensitivity level to a higher or lower level with the

ARROW keys.

3SEC

More info, articles, tutorials and videos support.safescan.com 19

English

To return to factory default settings: Press and hold [CLR]. The

machine will sound a “beep” to conrm that the factory default

settings have been restored.

Reset to default factory settings

6. Conﬁrm selection

Press START to conrm the set level.

More info, articles, tutorials and videos support.safescan.com

English

Some polymer banknotes

have large transparent areas

incorporated into their design, for

example some denominations of

AUD, CAD, SCT, NIR currencies

(among others). Due to the position

of these transparent areas on the

banknote, the 2210/2250 may not always properly count these

notes and will show an E4 (height error) or E5 (width error)

message during counting.

To enable continuous, error-free counting of polymer banknotes

with large transparent areas, there is an option to disable the height

and width (half note) detection.

To disable the height and width detection, press the arrow down

button for 3 seconds. The device will sound 3 beeps and show

“HEIGHT OFF” on the display.

Counting Polymer banknotes with large transparent

sections (valid for rmware version D08 / U08 or higher)

3SEC

Page is loading ...

Safescan 2210 / 2250 User manual

Brand: Safescan

Model: 2210 / 2250

Category: Money counting machines

Type: User manual

Download PDF

report

Safescan 2210 / 2250 User manual

Safescan 2210 / 2250 User manual

Related papers

Other documents