CURT 13920 Installation guide

CURT
Brand
CURT
Model
13920
Type
Installation guide

CURT 13920 is a hitch that can be used to tow trailers or carry heavy loads. It has a gross load capacity of 3,500 lbs when used as a weight-carrying hitch and 5,000 lbs when used as a weight distribution hitch. The tongue weight capacity is 350 lbs for weight-carrying and 500 lbs for weight distribution. The hitch is made of durable steel and has a black powder coat finish for corrosion resistance. It comes with all the necessary hardware for installation.

Before installing the hitch, you may need to drill holes in the frame rails of your vehicle. You will also need to trim the roll pan for ball mount installation. The installation process should take approximately 60 minutes.

CURT 13920 is a hitch that can be used to tow trailers or carry heavy loads. It has a gross load capacity of 3,500 lbs when used as a weight-carrying hitch and 5,000 lbs when used as a weight distribution hitch. The tongue weight capacity is 350 lbs for weight-carrying and 500 lbs for weight distribution. The hitch is made of durable steel and has a black powder coat finish for corrosion resistance. It comes with all the necessary hardware for installation.

Before installing the hitch, you may need to drill holes in the frame rails of your vehicle. You will also need to trim the roll pan for ball mount installation. The installation process should take approximately 60 minutes.

GROSS LOAD CAPACITY WHEN USED AS A WEIGHT CARRYING HITCH: LBS. TRAILER WEIGHT & LBS. TONGUE WEIGHT.
GROSS LOAD CAPACITY WHEN USED AS A WEIGHT DISTRIBUTION HITCH: LBS. TRAILER WEIGHT & LBS. TONGUE WEIGHT
***DO NOT EXCEED VEHICLE MANUFACTURER'S RECOMMENDED TOWING CAPACITY.***
HITCH WEIGHT: LBS.
INSTALL TIME: MINUTES
INSTALL NOTES:
INSTALLATION STEPS
PERIODICALLY CHECK THIS RECEIVER HITCH TO ENSURE THAT ALL FASTENERS
ARE TIGHT AND THAT ALL STRUCTURAL COMPONENTS ARE SOUND.
Curt Manufacturing Inc., warrants this product to be free of defects in material and/or workmanship at the time of retail purchase by the original purchaser. If the product is found to be defective,
Curt Manufacturing Inc., may repair or replace the product, at their option, when the product is returned, prepaid, with proof of purchase. Alteration to, misuse of, or improper installation of
this product voids the warranty. Curt Manufacturing Inc.'s liability is limited to repair or replacement of products found to be defective, and specifically excludes liability for incidental or
consequential loss or damage.
3,500 350
27
60
5,000 500
82-04 CHEVY S10, S15, GMC SONOMA PICKUPS W/ ROLL PAN
10/8/2012
13920
Parts List
DESCRIPTION
PART NUMBER
QTY
ITEM
HEX BOLT1/2 - 13 x 1 1/281
HEX FLANGE NUTHFN 121382
BEFORE AFTER
BUMPER
↓
PASSENGER
SIDE FRAME
RAIL
Note: Short box models will require the relocation of spare tire.
1) Loosen or remove spare tire as required. Short box models: remove the (2) rear exhaust hanger brackets.
2) Raise hitch into position and loosely install fasteners as shown above.
3) Some vehicle may require the drilling of holes, using a 17/32" drill bit, as shown.
4) Torque all 1/2" fasteners to 110 lb-ft.
5) For ball mount installation, cut the roll pan in the license plate area to provide access.
Note: License plate must be repositioned when the ball mount is installed.
6) Short box models: re-install hanger brackets, rear bracket must be flipped over.
- LOWER SPARE TIRE
- MAY REQUIRE DRILLING
- EXHAUST BRACKET RELOCATION
- TRIM ROLL PAN FOR BALL MOUNT
DRIVER SIDE
FRAME RAIL
PASSENGER SIDE
FRAME RAIL
DRILL HOLES IF NOT PRESENT
(BOTH FRAME RAILS)
TOOLS REQUIRED
RATCHET
3/4" SOCKET
3/4" BOXED END WRENCH
DRILL W/ 17/32" BIT
AVIATOR SHEARS / TIN SNIPS
TORQUE WRENCH
NOTE: CUTTING OF ROLL PAN IS REQUIRED
  • Page 1 1

CURT 13920 Installation guide

CURT
Brand
CURT
Model
13920
Type
Installation guide

CURT 13920 is a hitch that can be used to tow trailers or carry heavy loads. It has a gross load capacity of 3,500 lbs when used as a weight-carrying hitch and 5,000 lbs when used as a weight distribution hitch. The tongue weight capacity is 350 lbs for weight-carrying and 500 lbs for weight distribution. The hitch is made of durable steel and has a black powder coat finish for corrosion resistance. It comes with all the necessary hardware for installation.

Before installing the hitch, you may need to drill holes in the frame rails of your vehicle. You will also need to trim the roll pan for ball mount installation. The installation process should take approximately 60 minutes.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents