Biostar T41 HD Owner's manual

T41 HD Setup Manual

FCC Information and Copyright

This equipment has been tested and found to comply with the limits of a Class

B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed

to provide reasonable protection against harmful interference in a residential

installation. This equipment generates, uses, and can radiate radio frequency

energy and, if not installed and used in accordance with the instructions, may

cause harmful interference to radio communications. There is no guarantee

that interference will not occur in a particular installation.

The vendor makes no representations or warranties with respect to the

contents here and specially disclaims any implied warranties of merchantability

or fitness for any purpose. Further the vendor reserves the right to revise this

publication and to make changes to the contents here without obligation to

notify any party beforehand.

Duplication of this publication, in part or in whole, is not allowed without first

obtaining the vendor’s approval in writing.

The content of this user’s manual is subject to be changed without notice and

we will not be responsible for any mistakes found in this user’s manual. All the

brand and product names are trademarks of their respective companies.

Table of Contents

Chapter 1: Introduction ............................................................ 1

1.1 Before You Start......................................................................................... 1

1.2 Package Checklist..................................................................................... 1

1.3 Motherboard Features.............................................................................. 2

1.4 Rear Panel Connectors.............................................................................. 3

1.5 Motherboard Layout................................................................................. 4

Chapter 2: Hardware Installation ............................................. 5

2.1 Installing Central Processing Unit (CPU) ............................................... 5

2.2 FAN Headers .............................................................................................. 7

2.3 Installing System Memory ........................................................................ 8

2.4 Connectors and Slots................................................................................ 10

Chapter 3: Headers & Jumpers Setup ..................................... 14

3.1 How to Setup Jumpers............................................................................. 14

3.2 Detail Settings.......................................................................................... 14

Chapter 4: T-Series BIOS & Software ..................................... 19

4.1 T-Series BIOS............................................................................................. 19

4.2 T-Series Software...................................................................................... 27

Chapter 5: Useful Help ............................................................ 32

5.1 Driver Installation Note.......................................................................... 32

5.2 Extra Information.................................................................................... 33

5.3 AMI BIOS Beep Code............................................................................... 34

5.4 Troubleshooting....................................................................................... 35

Appendix: SPEC In Other Languages ...................................... 38

German.................................................................................................................. 36

French .................................................................................................................... 38

Italian..................................................................................................................... 40

Spanish ................................................................................................................... 42

Portuguese ............................................................................................................ 44

Polish...................................................................................................................... 46

Russian ................................................................................................................... 48

Arabic..................................................................................................................... 50

Japanese ................................................................................................................ 52

T41 HD

1

CHAPTER 1: INTRODUCTION

1.1 B

EFORE YOU START

Thank you for choosing our product. Before you start installing the

motherboard, please make sure you follow the instructions below:

 Prepare a dry and stable working environment with

sufficient lighting.

 Always disconnect the computer from power outlet

before operation.

 Before you take the motherboard out from anti-static

bag, ground yourself properly by touching any safely

grounded appliance, or use grounded wrist strap to

remove the static charge.

 Avoid touching the components on motherboard or the

rear side of the board unless necessary. Hold the board

on the edge, do not try to bend or flex the board.

 Do not leave any unfastened small parts inside the

case after installation.

Loose parts will cause short circuits which may

damage the equipment.

 Keep the computer from dangerous area, such as heat

source, humid air and water.

 The operating temperatures of the computer should be

0 to 45 degrees Celsius.

1.2 PACKAGE CHECKLIST

HDD Cable X 1 (optional)

Serial ATA Cable X 3

Rear I/O Panel for ATX Case X 1

User’s Manual X 1

Fully Setup Driver CD X 1

FDD Cable X 1 (optional)

USB 2.0 Cable X1 (optional)

S/PDIF Cable X 1 (optional)

Serial ATA Power Cable X 1 (optional)

DVI to HDMI Dongle (optional)

Note: The package contents may be different due to area or your motherboard version.

Motherboard Manual

2

1.3 MOTHERBOARD FEATURES

SPEC

CPU

LGA 775

Intel Core2Duo / Core2Quad / Celeron 4xx

/ Pentium Dual-core / Celeron Dual-core

processor

Supports Hyper-Threading / Execute Disable Bit /

Enhanced Intel SpeedStep® / Int el Archit ecture-64 /

Extended Memory 64 Technology / Virtualization

Technology

FSB 800 / 1066 / 1333 MHz

Chipset

Intel G41 A3

Intel ICH7

Super I/O

ITE 8718F

Provides the most commonly used legacy

Super I/O functionality.

Low Pin Count Interface

Environment Control in it iatives,

Hardware Monitor Controller

Fan Speed Contro ller

ITE's "S mart Guard ian" funct ion

Main

Memory

DIMM Slots x 2

Each DIMM supports 256MB / 512MB /

1GB / 2GB / 4GB DDR2

Max Memory Capacity 8GB

Dual Channel Mode DDR2 memory modu le

Supports DDR2 800/667

Registered DIMM and ECC DIMM is not supported

Graphics GMA X4500 Max Shared Video Memory is 256MB

IDE Integr ated IDE Contro ller

Ultra DMA 33 / 66 / 100 Bus Master Mode

supports PIO Mode 0~4

SATA 2 Integrated Serial ATA Controller

Data transfer rates up to 3.0 Gb/s.

SATA Version 2.0 specificat ion co mp liant

LAN Realtek RTL 8111DL

10 / 100 Mb/s / 1Gb/s auto negotiation

Half / Full duplex capability

Sound

Codec

ALC662

5.1 channels audio out

High Definition Audio

PCI slot x3 Supports PCI expansion cards

PCI Express x 16 slot x1 Supports PCI-E x16 expansion cards

Slots

PCI Express x 1 slot x2 Supports PCI-E x1 expansion cards

Floppy Connector x1 Each connector supports 2 Floppy drives

IDE Connector x1 Each connector supports 2 IDE device

SATA Connector x4 Each connector supports 1 SATA devices

Front Panel Connector x1 Supports front panel facilities

On Board

Connectors

Front Audio Connector x1 Supports front panel audio function

T41 HD

3

SPEC

CD-in Connector x1 Supports CD audio-in function

S/PDIF out Connector x1 Supports digital audio out function

CPU Fan Header x1 CPU Fan power supply (with Smart Fan function)

System Fan Header x2 System Fan Power supply

Clear CMOS Header x1 Restore CMOS dat a to factory default

USB Connector x2 Each connector supports 2 front panel USB ports

Serial port Connector x1 Connects to RS-232 Port

Power Connector (24pin) x1 Connects to Power supply

Power Connector (4pin) x2 Connects to Power supply

Back Panel

I/O

PS/2 Keyboard x1

PS/2 Mouse x1

VGA port x1

DVI-D Port x1

LAN port x1

USB Port x4

Audio Jack x3

Connects to PS/2 Keyboard

Connects to PS/2 Mouse

Connect to D-SUB monitor

Connect to DVI monitor

Connect to RJ-45 ethernet cab le

Connect to USB devices

Provide Audio-In/Out and microphone connection

Board Size 210 (W) x 305 (L) mm ATX

OS Support

Windows 2000 / XP / Vista / 7

Biostar reserves the right to add or remove support for

any OS with or without notice

Note: HDMI Audio is supported in WinXP with SP3 / Vista 32 / Vista 64

1.4 REAR PANEL CONNECTORS

PS/2

Mouse

PS/2

Keyboard

USBX2USBX2

LAN

VGA

Line In/

Surround

Line Out

Mic In 1/

Bass/ Center

DVI-D

Since the audio chip supports High Definition Audio Specification, the function of each audio

jack can be defined by software. The input / output function of each audio jack listed above

represents the default setting. However, when connecting external microphone to the audio

port, please use the Line In (blue) and Mic In (Pink) audio jack.

Motherboard Manual

4

1.5 MOTHERBOARD LAYOUT

KBMS1

VGA1

DVI1

USB1

RJ45USB1

AU DI O 1

ATXPWR2

CPU_FAN1

JUSBV1

CD_IN1

SYS_FAN1

SPDIF1

LAN

CODEC

Super

I/O

F_AUDIO1

PEX1_1

PEX1_2

PCI1

PCI2

PCI3

FDD1

SYS_FAN2

JUSBV2

F_USB2F_USB1

PANEL1

IDE1

SATA1 SATA3

SATA2 SATA4

SW_RST1

SW_PWR1

BIOS

JCM O S1

LED1

LED2

BAT1

ATXPWR1

D DR2_A 1

D DR2_B 1

Intel

ICH7

Intel

G41 A3

LGA775

CPU1

AUXPWR1

PEX16_1

PH 1

PH2

PH4

PH 3

F_COM1

Note: represents the 1■

st

pin.

T41 HD

5

CHAPTER 2: HARDWARE INSTALLATION

2.1 I

NSTALLING CENTRAL PROCESSING UNIT (CPU)

Special Notice:

Remove Pin Cap before installation, and make good preservation

for future use. When the CPU is removed, cover the Pin Cap on the

empty socket to ensure pin legs won’t be damaged.

Pin Cap

Step 1: Pull the socket locking lever out from the socket and then raise

the lever up to a 90-degree angle.

Motherboard Manual

6

Step 2: Look for the triangular cut edge on socket, and the golden dot on

CPU should point forwards this triangular cut edge. The CPU will

fit only in the correct orientation.

Step 2-1:

Step 2-2:

Step 3: Hold the CPU down firmly, and then lower the lever to locked

position to complete the installation.

Step 4: Put the CPU Fan and heatsink assembly on the CPU and buckle it

on the retention frame. Connect the CPU FAN power cable into

the CPU_FAN1. This completes the installation.

T41 HD

7

2.2 FAN HEADERS

These fan headers support cooling-fans built in the computer. The fan

cable and connector may be different according to the fan manufacturer.

Connect the fan cable to the connector while matching the black wire to

pin#1.

CPU_FAN1: CPU Fan Header

Assignment

1 Ground

2 +12V

3

FAN RPM rate

sense

1

4

4 Smart Fan

Control

SYS_FAN1: NorthBridge Fan Header

SYS_FAN2: System Fan Header

Assignment

1 Ground

2 +12V

SYS_FAN1

13

SYS_FAN2

3 FAN RPM rate

sense

Note:

SYS_FAN1/2 supports 3-pin head connectors; CPU_FAN1 supports 4-pin head

connector. When connecting with wires onto connectors, please note that the red wire is

the positive and should be connected to pin#2, and the black wire is Ground and should

be connected to GND.

Motherboard Manual

8

2.3 INSTALLING SYSTEM MEMORY

A. Memory Modules

DDR2 _A1

DDR2 _B1

1. Unlock a DIMM slot by pressing the retaining clips outward. Align a

DIMM on the slot such that the notch on the DIMM matches the

break on the Slot.

2. Insert the DIMM vertically and firmly into the slot until the retaining

chip snap back in place and the DIMM is properly seated.

T41 HD

9

B. Memory Capacity

DIMM Socket

Location

DDR Module

Total Mem ory

Size

DDR2_A1 256MB/512MB/1GB/2GB/4GB

DDR2_B1 256MB/512MB/1GB/2GB/4GB

Max is 8GB.

C. Dual Channel Memory installation

Please refer to the following requirements to activate Dual Channel function:

Install memory module of the same density in pairs, shown in the table.

Dual Channel Status

DDR2_A1

DDR2_B1

Disabled O X

Disabled X O

Enabled O O

(O means memory installed, X means memory not installed.)

The DRAM bus width of the memory module must be the same (x8 or

x16)

Motherboard Manual

10

2.4 CONNECTORS AND SLOTS

FDD1: Floppy Disk Connector

The motherboard provides a standard floppy disk connector that supports 360K,

720K, 1.2M, 1.44M and 2.88M floppy disk types. This connector supports the

provided floppy drive ribbon cables.

34

331

2

IDE1: Hard Disk Connector

The motherboard has a 32-bit Enhanced PCI IDE Controller that provides PIO

Mode 0~4, Bus Master, and Ultra DMA 33/66/100 functionality.

An IDE connector can connect a master and a slave drive, so you can connect

up to two hard disk drives.

1

240

39

T41 HD

11

SATA1~SATA4: Serial ATA Connectors

The motherboard has a PCI to SATA Controller with 4 channels SATA interface.

It satisfies the SATA 2.0 spec and with transfer rate of 3.0Gb/s.

Assignment

1 Ground

2 TX+

3 TX-

4 Ground

5 RX-

6 RX+

1

4

7

SATA1

SATA2

SATA3

S

A

T

A

4

7 Ground

AUXPWR1: Auxiliary Power for Graphics

This connector is an auxiliary power connection for graphics cards. Exclusive

power for the graphics card provides better graphics performance.

Assignment

1 +12V

2 Ground

3 Ground

4 VCC

14

Motherboard Manual

12

ATXPWR1: ATX Power Source Connector

This connector allows user to connect 24-pin power connector on the ATX

power supply.

1

12

13

24

Pin Assignment Pin Assignment

13 +3.3V 1 +3.3V

14 -12V 2 +3.3V

15 Gro und 3 Gro und

16 PS_ON 4 +5V

17 Gro und 5 Gro und

18 Ground 6 +5V

19 Gro und 7 Gro und

20 NC 8 PW_OK

21 +5V 9 Standby Voltage+5V

22 +5V 10 +12V

23 +5V 11 +12V

24 Ground 12 +3.3V

ATXPWR2: ATX Power Source Connector

This connector provides +12V to CPU power circuit.

Assignment

1 +12V

2 +12V

3 Ground

12

34

4 Ground

Note:

Before power on the system, please make sure that both ATXPWR1 and ATXPWR2

connectors have been plugged-in.

T41 HD

13

PEX16_1: PCI-Express x16 Slot

- PCI-Express 1.0a compliant.

- Maximum theoretical realized bandwidth of 4GB/s simultaneously per

direction, for an aggregate of 8GB/s totally.

PEX1_1/PEX1_2: PCI-Express x1 Slots

- PCI-Express 1.0a compliant.

- Maximum theoretical realized bandwidth of 250MB/s simultaneously per

direction, for an aggregate of 500MB/s totally.

- PCI-Express supports a raw bit-rate of 2.5GB/s on the data pins.

- 2X bandwidth over the traditional PCI architecture.

PEX16_1

PEX1_1

PEX1_2

PCI1~PCI3: Peripheral Component Interconnect Slots

This motherboard is equipped with 3 standard PCI slots. PCI stands for

Peripheral Component Interconnect, and it is a bus standard for expansion

cards. This PCI slot is designated as 32 bits.

PCI3

PCI2

PCI1

Motherboard Manual

14

CHAPTER 3: HEADERS & JUMPERS SETUP

3.1 H

OW TO SETUP JUMPERS

The illustration shows how to set up jumpers. When the jumper cap is

placed on pins, the jumper is “close;” if not, that means the jumper is

“open”.

Pin opened Pin closed Pin1-2 closed

3.2 D

ETAIL SETTINGS

PANEL1: Front Panel Header

This 16-pin connector includes Power-on, Reset, HDD LED, Power LED, and

speaker connection. It allows user to connect the PC case’s front panel switch

functions.

1

9

8

16

POW_LED

On/Off

RST

HLED

SPK

++

+

-

Pin Assignment Function Pin Assignment Function

1 +5V 9 N/A

2 N/A 10 N/A

N/A

3 N/A 11 N/A N/A

4 Speaker

Speaker

Connector

12 Power LED (+)

5 HDD LED (+) 13 Power LED (+)

6 HDD LED (-)

Hard drive

LED

14 Power LED (-)

Power LED

7 Ground 15 Power button

8 Reset control

Reset button

16 Ground

Power-on button

T41 HD

15

F_USB1/F_USB2: Headers for USB 2.0 Ports at Front Panel

These headers allow user to connect additional USB cable on the PC front panel.

They also can be connected with internal USB devices, like USB card reader.

Assignment

1 +5V (fused)

2 +5V (fused)

3 USB-

4 USB-

5 USB+

6 USB+

7 Ground

8 Ground

9 Key

1

2

9

10

F_USB1 F_USB2

10 NC

JCMOS1: Clear CMOS Header

Placing the jumper on pin2-3 allows user to restore the BIOS safe setting and

the CMOS data. Please carefully follow the procedures to avoid damaging the

motherboard.

1

3

Pin 1-2 Close:

Normal Operation (default).

1

3

1

3

Pin 2-3 Close:

Clear CMOS data.

※ Clear CMOS Procedures:

1. Remove AC power line.

2. Set the jumper to “Pin 2-3 close”.

3. Wait for five seconds.

4. Set the jumper to “Pin 1-2 close”.

5. Power on the AC.

6. Reset your desired password or clear the CMOS data.

Motherboard Manual

16

F_AUDIO1: Front Panel Audio Header

This header allows user to connect the front audio output cable with the PC front

panel. This header allows only HD audio front panel connector; AC’97 connector

is not acceptable.

Assignment

1 Mic Left in

2 Ground

3 Mic Right in

4 GPIO

5 Right line in

6 Jack Sense

7 Front Sense

8 Key

9 Left line in

1

2

9

10

10 Jack Sense

CD_IN1: CD-ROM Audio-in Connector

This connector allows user to connect the audio source from the variaty devices,

like CD-ROM, DVD-ROM, PCI sound card, PCI TV turner card etc..

Assignment

1 Left Channel Input

2 Ground

3 Ground

1

4

4 Right Channel Input

T41 HD

17

SPDIF1: Digital Audio-out Connector

This connector allows user to connect the PCI bracket SPDIF output header.

Assignment

1 +5V

2 SPDIF_OUT

1

3

3 Ground

JUSBV1/JUSBV2: Power Source Headers for USB Ports

Pin 1-2 Close:

JUSBV1: +5V for USB ports at USB1/RJ45USB1.

JUSBV2: +5V for USB ports at front panel (F_USB1/F_USB2).

Pin 2-3 Close:

JUSBV1: +5V STB for USB ports at USB1/RJ45USB1.

JUSBV2: +5V STB for USB ports at front panel (F_USB1/F_USB2).

13

Pin 1-2 close

3

1

JUSBV1

JUSBV2

31

13

Pin 2-3 close

Motherboard Manual

18

On-Board LED Indicators

There are 6 LED indicators on the motherboard showing system status.

LED2

LED1

PH2

PH1

PH4

PH3

LED1 & LED2: Debug Indicators

PH1 ~ PH4: Power Status Indicators

Please refer to the tables below for specific messages:

LED1 LED2 Message

ON ON Normal

ON OFF Memory Error

OFF ON VGA Error

OFF OFF Abnormal: CPU / Chipset error.

PH1 ~ PH4 Phase Indicator

ON Phase Active

OFF Phase Inactive

On-Board Buttons

There are 2 on-board buttons.

SW_RST1

SW_PWR1

SW_RST1: Reset button.

SW_PWR1: Power Switch button.

Page is loading ...

Biostar T41 HD Owner's manual

Biostar T41 HD Owner's manual

Related papers

Other documents