Enterasys Networks C2K122-24 User manual

Category
Network switches
Type
User manual
Enterasys
®
SecureStack
C2
Gigabit Ethernet Switch
Hardware Installation Guide
C2K122-24
P/N 9034087-04
7.5x9-inch cover with bleed on 4 sides
i
Notice
Enterasys Networksreservestherighttomakechangesinspecificationsandotherinformationcontainedinthis
documentanditswebsitewithoutpriornotice.ThereadershouldinallcasesconsultEnterasys Networksto
determinewhetheranysuchchangeshavebeenmade.
Thehardware,firmware,orsoftwaredescribedinthisdocumentissubject
tochangewithoutnotice.
INNOEVENTSHALLENTERASYS NETWORKSBELIABLEFORANYINCIDENTAL,INDIRECT, SPECIAL,OR
CONSEQUENTIALDAMAGESWHATSOEVER(INCLUDINGBUTNOTLIMITEDTOLOSTPROFITS)ARISING
OUTOFORRELATEDTOTHISDOCUMENT,WEBSITE,ORTHEINFORMATIONCONTAINEDINTHEM,EVEN
IFENTERASYS NETWORKSHASBEENADVISEDOF,KNEW
OF,ORSHOULDHAVEKNOWNOF,THE
POSSIBILITYOFSUCHDAMAGES.
Enterasys Networks, Inc.
50MinutemanRoad
Andover,MA01810
©2008Enterasys Networks, Inc.Allrightsreserved.
PartNumber: 903408704 February 2008
ENTERASYS,ENTERASYS NETWORKS,ENTERASYSMATRIX,ENTERASYSSECURESTACK,LANVIEW,
NETSIGHT,WEBVIEW,andanylogosassociatedtherewith,aretrademarksorregisteredtrademarksof
Enterasys Networks, Inc.,intheUnitedStatesandother
countries.
Allotherproductnamesmentionedinthismanualmaybetrademarksorregisteredtrademarksoftheirrespective
companies.
DocumentationURL:http://www.enterasys.com/support/manuals
DocumentacionURL:http://www.enterasys.com/support/manuals
DokumentationimInternet:http://www.enterasys.com/support/manuals
Electrical Hazard: Only qualified personnel should perform installation procedures.
Riesgo Electrico: Solamente personal calificado debe realizar procedimientos de instalacion.
Elektrischer Gefahrenhinweis: Installationen sollten nur durch ausgebildetes und qualifiziertes
Personal vorgenommen werden.
ii
REGULATORY COMPLIANCE INFORMATION
FEDERAL COMMUNICATIONS COMMISSION (FCC) NOTICE
ThisdevicecomplieswithPart15oftheFCCrules.Operationissubjecttothefollowingtwoconditions:(1)thisdevice
maynotcauseharmfulinterference,and(2)thisdevicemustacceptanyinterferencereceived,includinginterference
thatmaycauseundesiredoperation.
NOTE: Thisequipmenthasbeentestedandfoundtocomply
withthelimitsforaclassAdigitaldevice,pursuantto
Part15oftheFCCrules.Theselimitsaredesignedtoprovidereasonableprotectionagainstharmfulinterferencewhen
theequipmentisoperatedinacommercialenvironment.Thisequipmentuses,generates,andcanradiateradio
frequencyenergyandifnot
installedinaccordancewiththeoperatorsmanual,maycauseharmfulinterferenceto
radiocommunications.Operationofthisequipmentinaresidentialareaislikelytocauseinterferenceinwhichcase
theuserwillberequiredtocorrecttheinterferenceathisownexpense.
WARNING: Changesormodificationsmadetothisdevicewhich
arenotexpresslyapprovedbytheparty
responsibleforcompliancecouldvoidtheusersauthoritytooperatetheequipment.
INDUSTRY CANADA NOTICE
ThisdigitalapparatusdoesnotexceedtheclassAlimitsforradionoiseemissionsfromdigitalapparatussetoutinthe
RadioInterferenceRegulationsoftheCanadianDepartmentofCommunications.
Leprésentappareilnumériquen’émetpasdebruitsradioélectriquesdépassantleslimitesapplicablesauxappareils
numériquesdelaclassAprescrites
dansleRèglementsurlebrouillageradioélectriqueédictéparleministèredes
CommunicationsduCanada.
CLASS A ITE NOTICE
WARNING: ThisisaClassAproduct.Inadomesticenvironmentthisproductmaycauseradiointerferenceinwhich
casetheusermayberequiredtotakeadequatemeasures.
CLASE A. AVISO DE ITE
ADVERTENCIA:EsteesunproductodeClaseA.Enunambientedomésticoesteproductopuedecausarinterferencia
deradioencuyocasopuedeserrequeridotomarmedidasadecuadas.
KLASSE A ITE ANMERKUNG
WARNHINWEIS:DiesesProduktzähltzurKlasseA(Industriebereich).InWohnbereichenkanneshierdurchzu
Funkstörungenkommen,dahersolltenangemesseneVorkehrungenzumSchutzgetroffenwerden.
PRODUCT SAFETY
Thisproductcomplieswiththefollowing:UL60950,CSAC22.2No.60950,73/23/EEC,EN60950,IEC60950,EN 60825,
21 CFR1040.10.
SEGURIDAD DEL PRODUCTO
ElproductodeEnterasyscumpleconlosiguiente:UL60950,CSAC22.2No.60950,73/23/EEC,EN 60950,IEC 60950,
EN 60825,21 CFR1040.10.
PRODUKTSICHERHEIT
DiesesProduktentsprichtdenfolgendenRichtlinien:UL60950,CSAC22.2No.60950,73/23/EEC,EN60950,
IEC 60950,EN60825,21CFR1040.10.
iii
ELECTROMAGNETIC COMPATIBILITY (EMC)
Thisproductcomplieswiththefollowing:47CFRParts2and15,CSAC108.8,89/336/EEC,EN55022,EN6100032,
EN 6100033,EN55024,AS/NZSCISPR22,VCCIV3.
COMPATIBILIDAD ELECTROMÁGNETICA (EMC)
EsteproductodeEnterasyscumpleconlosiguiente:47CFRPartes2y15,CSAC108.8,89/336/EEC,EN55022,
EN 55024,EN6100032,EN6100033,AS/NZSCISPR22,VCCIV3.
ELEKTRO- MAGNETISCHE KOMPATIBILITÄT ( EMC )
DiesesProduktentsprichtdenfolgendenRichtlinien:47CFRParts2and15,CSAC108.8,89/336/EEC,EN55022,
EN 6100032,EN6100033,EN55024,AS/NZSCISPR22,VCCIV3.
HAZARDOUS SUBSTANCES
ThisproductcomplieswiththerequirementsofEuropeanDirective,2002/95/EC,RestrictionofHazardousSubstances
(RoHS)inElectricalandElectronicEquipment.
EUROPEAN WASTE ELECTRICAL AND ELECTRONIC EQUIPMENT (WEEE) NOTICE
InaccordancewithDirective2002/96/ECoftheEuropeanParliamentonwasteelectricalandelectronicequipment
(WEEE):
1. Thesymbolaboveindicatesthatseparatecollectionofelectricalandelectronicequipmentisrequiredandthatthis
productwasplacedontheEuropeanmarketafterAugust13,2005,thedateofenforcementforDirective
2002/96/EC.
2. When
thisproducthasreachedtheendofitsserviceablelife,itcannotbedisposedofasunsortedmunicipalwaste.
Itmustbecollectedandtreatedseparately.
3. IthasbeendeterminedbytheEuropeanParliamentthattherearepotentialnegativeeffectsontheenvironment
andhumanhealthasaresultofthe
presenceofhazardoussubstancesinelectricalandelectronicequipment.
4. Itistheusers’responsibilitytoutilizetheavailablecollectionsystemtoensureWEEEisproperlytreated.
Forinformationabouttheavailablecollectionsystem,pleasegotohttp://www.enterasys.com/services/support/
or
contactEnterasysCustomerSupportat35361705586(Ireland).
iv
ѻ
ѻક䇈ᯢк䰘ӊ
Supplement to Product Instructions
᳝↦᳝ᆇ⠽䋼៪ܗ㋴(Hazardous Substance)
䚼ӊৡ⿄
(Parts)
䪙
3E
∲
+J
䬝
&G
݁Ӌ䫀
&U

໮⒈㘨㣃
3%%
໮⒈Ѡ㣃䝮
3%'(
䞥ሲ䚼ӊ
(Metal Parts)
ƻ ƻ ƻ ƻ
⬉䏃῵ഫ
(Circuit Modules)
ƻ ƻ ƻ ƻ
⬉㓚ঞ⬉㓚㒘ӊ
(Cables & Cable Assemblies)
ƻ ƻ ƻ ƻ
ล᭭੠㘮ড়⠽䚼ӊ
(Plastic and Polymeric parts)
ƻƻ ƻ ƻ ƻ ƻ
⬉䏃ᓔ݇
(Circuit Breakers)
ƻƻ ƻ ƻ ƻ ƻ
ƻ˖ 㸼⼎䆹᳝↦᳝ᆇ⠽䋼೼䆹䚼ӊ᠔᳝ഛ䋼ᴤ᭭Ёⱘ৿䞣ഛ೼ SJ/T 11363-2006 ᷛޚ㾘ᅮⱘ䰤䞣㽕∖ҹϟDŽ
Indicates that the concentration of the hazardous substance in all homogeneous materials in the parts is
below the relevant threshold of the SJ/T 11363-2006 standard.
h˖ 㸼⼎䆹᳝↦᳝ᆇ⠽䋼㟇ᇥ೼䆹䚼ӊⱘᶤϔഛ䋼ᴤ᭭Ёⱘ৿䞣䍙ߎSJ/T 11363-2006 ᷛޚ㾘ᅮⱘ䰤䞣㽕∖DŽ
Indicates that the concentration of the hazardous substance of at least one of all homogeneous
materials in the parts is above the relevant threshold of the SJ/T 11363-2006 standard.
ᇍ䫔ଂП᮹ⱘ᠔ଂѻકᴀ㸼ᰒ⼎
߃߯կᑨ䫒ⱘ⬉ᄤֵᙃѻકৃ㛑ࣙ৿䖭ѯ⠽䋼DŽ⊼ᛣ೼᠔ଂѻકЁৃ㛑Ӯгৃ㛑ϡӮ৿᳝᠔᳝᠔߫ⱘ䚼ӊDŽ
This table shows where these substances may be found in the supply chain of Enterasys’ electronic
information products, as of the date of sale of the enclosed product. Note that some of the component types
listed above may or may not be a part of the enclosed product.
䰸䴲঺໪⡍߿ⱘᷛ⊼ℸᷛᖫЎ䩜ᇍ᠔⍝ঞѻકⱘ⦃ֱՓ⫼ᳳᷛᖫᶤѯ䳊䚼ӊӮ
᳝ϔϾϡৠⱘ⦃ֱՓ⫼ᳳ՟བ⬉∴ऩܗ῵ഫ䌈೼݊ѻકϞ
ℸ⦃ֱՓ⫼ᳳ䰤া䗖⫼Ѣѻકᰃ೼ѻક᠟ݠЁ᠔㾘ᅮⱘᴵӊϟᎹ԰
The Environmentally Friendly Use Period (EFUP) for all enclosed products and their parts
are per the symbol shown here, unless otherwise marked. Certain parts may have a
different EFUP (for example, battery modules) and so are marked to reflect such. The
Environmentally Friendly Use Period is valid only when the product is operated under the
conditions defined in the product manual.
20
v
VCCI NOTICE
ThisisaclassAproductbasedonthestandardoftheVoluntaryControlCouncilforInterferencebyInformation
TechnologyEquipment(VCCI).Ifthisequipmentisusedinadomesticenvironment,radiodisturbancemayarise.
Whensuchtroubleoccurs,theusermayberequiredtotakecorrectiveactions.
BSMI EMC STATEMENT — TAIWAN
ThisisaclassAproduct.Inadomesticenvironmentthisproductmaycauseradiointerferenceinwhichcasetheuser
mayberequiredtotakeadequatemeasures.
SAFETY INFORMATION
CLASS 1 LASER TRANSCEIVERS
SINGLE MODE NETWORK EXPANSION MODULES USE CLASS 1 LASER TRANSCEIVERS.
READ THE FOLLOWING SAFETY INFORMATION
BEFORE INSTALLING OR OPERATING THESE MODULES.
TheClass1lasertransceiversuseanopticalfeedbacklooptomaintainClass1operationlimits.Thiscontrolloop
eliminatestheneedformaintenancechecksoradjustments.Theoutputisfactoryset,anddoesnotallowanyuser
adjustment.Class1Lasertransceiverscomplywiththefollowingsafetystandards:
•21CFR
1040.10and1040.11U.S.DepartmentofHealthandHumanServices(FDA).
•IECPublication825(InternationalElectrotechnicalCommission).
CENELECEN60825(EuropeanCommitteeforElectrotechnicalStandardization).
Whenoperatingwithintheirperformancelimitations,lasertransceiveroutputmeetstheClass1accessibleemission
limitofallthreestandards.Class1levelsoflaserradiationare
notconsideredhazardous.
Whentheconnectorisinplace,alllaserradiationremainswithinthefiber.Themaximumamountofradiantpower
exitingthefiber(undernormalconditions)is‐12.6dBmor55x10
6
watts.
Removingtheopticalconnectorfromthetransceiverallowslaserradiationtoemitdirectlyfromtheopticalport.The
maximumradiancefromtheopticalport(underworstcaseconditions)is0.8Wcm
2
or8x10
3
Wm
2
sr1.
Donotuseopticalinstrumentstoviewthelaseroutput.Theuseofopticalinstrumentstoviewlaseroutputincreases
eyehazard.Whenviewingtheoutputopticalport,powermustberemovedfromthenetworkadapter.
vi
DECLARATION OF CONFORMITY
ApplicationofCouncilDirective(s): 89/336/EEC
73/23/EEC
Manufacturer’sName: Enterasys Networks, Inc.
ManufacturersAddress: 50MinutemanRoad
Andover,MA01810
USA
EuropeanRepresentativeAddress: Enterasys Networks,Ltd.
NexusHouse,NewburyBusinessPark
LondonRoad,Newbury
BerkshireRG142PZ,England
Conformance to Directive(s)/Product Standards: ECDirective89/336/EEC
EN55022
EN6100032
EN6100033
EN55024
ECDirective73/23/EEC
EN60950
EN60825
EquipmentType/Environment: NetworkingEquipment,for
useinaCommercial
orLightIndustrialEnvironment.
Enterasys Networks, Inc.declaresthattheequipmentpackagedwiththisnoticeconformstotheabovedirectives.
vii
ENTERASYS NETWORKS, INC.
FIRMWARE LICENSE AGREEMENT
BEFOREOPENINGORUTILIZINGTHEENCLOSEDPRODUCT,
CAREFULLYREADTHISLICENSEAGREEMENT.
Thisdocumentisanagreement(“Agreement”)betweentheenduser(“You”)andEnterasys Networks, Inc.onbehalf
ofitselfanditsAffiliates(ashereinafterdefined)(“Enterasys”)thatsetsforthYourrightsandobligationswithrespect
totheEnterasyssoftwareprogram/firmwareinstalledon
theEnterasysproduct(includinganyaccompanying
documentation,hardwareormedia)(“Program”)inthepackageandprevailsoveranyadditional,conflictingor
inconsistenttermsandconditionsappearingonanypurchaseorderorotherdocumentsubmittedbyYou.Affiliate”
meansanyperson,partnership,corporation,limitedliabilitycompany,orotherformofenterprise
thatdirectlyor
indirectlythroughoneormoreintermediaries,controls,oriscontrolledby,orisundercommoncontrolwiththeparty
specified.ThisAgreementconstitutestheentireunderstandingbetweentheparties,andsupersedesallprior
discussions,representations,understandingsoragreements,whetheroralorinwriting,betweenthepartieswith
respect
tothesubjectmatterofthisAgreement.TheProgrammaybecontainedinfirmware,chipsorothermedia.
BYINSTALLINGOROTHERWISEUSINGTHEPROGRAM,YOUREPRESENTTHATYOUAREAUTHORIZEDTO
ACCEPTTHESETERMSONBEHALFOFTHEENDUSER(IFTHEENDUSERISANENTITYONWHOSEBEHALF
YOUAREAUTHORIZEDTOACT,“YOU”AND“YOUR”SHALLBEDEEMEDTOREFERTOSUCHENTITY)AND
THATYOUAGREETHATYOUAREBOUNDBYTHETERMSOFTHISAGREEMENT,WHICHINCLUDES,
AMONGOTHERPROVISIONS,THELICENSE,THEDISCLAIMEROFWARRANTYANDTHELIMITATIONOF
LIABILITY.IFYOUDONOT
AGREETOTHETERMSOFTHISAGREEMENTORARENOTAUTHORIZEDTO
ENTERINTOTHISAGREEMENT,ENTERASYSISUNWILLINGTOLICENSETHEPROGRAMTOYOUANDYOU
AGREETORETURNTHEUNOPENEDPRODUCTTOENTERASYSORYOURDEALER,IFANY,WITHINTEN
(10)DAYSFOLLOWINGTHEDATEOFRECEIPTFORA
FULLREFUND.
IFYOUHAVEANYQUESTIONSABOUTTHISAGREEMENT,CONTACTENTERASYS NETWORKS,LEGAL
DEPARTMENTAT(978)6841000.
YouandEnterasysagreeasfollows:
1. LICENSE. Youhavethenonexclusiveandnontransferablerighttouseonlytheone(1)copyoftheProgram
providedinthispackagesubjecttothe
termsandconditionsofthisAgreement.
2. RESTRICTIONS. ExceptasotherwiseauthorizedinwritingbyEnterasys,Youmaynot,normayYoupermitany
thirdpartyto:
(i) Reverseengineer,decompile,disassembleormodifytheProgram,inwholeorinpart,includingforreasons
oferrorcorrectionorinteroperability,excepttotheextentexpressly
permittedbyapplicablelawandtothe
extentthepartiesshallnotbepermittedbythatapplicablelaw,suchrightsareexpresslyexcluded.
InformationnecessarytoachieveinteroperabilityorcorrecterrorsisavailablefromEnterasysuponrequest
anduponpaymentofEnterasys’applicablefee.
(ii) IncorporatetheProgram,inwholeorin
part,inanyotherproductorcreatederivativeworksbasedonthe
Program,inwholeorinpart.
(iii) Publish,disclose,copy,reproduceortransmittheProgram,inwholeorinpart.
(iv) Assign,sell,license,sublicense,rent,lease,encumberbywayofsecurityinterest,pledgeorotherwisetransfer
theProgram,inwhole
orinpart.
(v) Removeanycopyright,trademark,proprietaryrights,disclaimerorwarningnoticeincludedonorembedded
inanypartoftheProgram.
viii
3. APPLICABLELAW. ThisAgreementshallbeinterpretedandgovernedunderthelawsandinthestateand
federalcourtsoftheCommonwealthofMassachusettswithoutregardtoitsconflictsoflawsprovisions.Youacceptthe
personaljurisdictionandvenueoftheCommonwealthofMassachusettscourts.Noneofthe1980UnitedNations
ConventiononContractsfortheInternationalSaleofGoods,theUnitedNationsConventionontheLimitationPeriod
intheInternationalSaleofGoods,andtheUniformComputerInformationTransactionsActshallapplytothis
Agreement.
4. EXPORTRESTRICTIONS. YouunderstandthatEnterasysanditsAffiliatesaresubjecttoregulationbyagencies
oftheU.S.Government,includingtheU.S.DepartmentofCommerce,whichprohibitexportordiversionofcertain
technicalproductstocertaincountries,unlessalicensetoexporttheProgramisobtainedfromtheU.S.Governmentor
anexceptionfromobtainingsuchlicensemayberelieduponbytheexportingparty.
If
theProgramisexportedfromtheUnitedStatespursuanttotheLicenseExceptionCIVundertheU.S.Export
AdministrationRegulations,YouagreethatYouareacivilenduseroftheProgramandagreethatYouwillusethe
Programforcivilendusesonlyandnotformilitarypurposes.
If
theProgramisexportedfromtheUnitedStatespursuanttotheLicenseExceptionTSRundertheU.S.Export
AdministrationRegulations,inadditiontotherestrictionontransfersetforthinSection1or2ofthisAgreement,You
agreenotto(i)reexportorreleasetheProgram,thesourcecodefor
theProgramortechnologytoanationalofa
countryinCountryGroupsD:1orE:2(Albania,Armenia,Azerbaijan,Belarus,Cambodia,Cuba,Georgia,Iraq,
Kazakhstan,Laos,Libya,Macau,Moldova,Mongolia,NorthKorea,thePeoplesRepublicofChina,Russia,Tajikistan,
Turkmenistan,Ukraine,Uzbekistan,Vietnam,orsuchothercountriesasmaybe
designatedbytheUnitedStates
Government),(ii)exporttoCountryGroupsD:1orE:2(asdefinedherein)thedirectproductoftheProgramorthe
technology,ifsuchforeignproduceddirectproductissubjecttonationalsecuritycontrolsasidentifiedontheU.S.
CommerceControlList,or(iii)ifthedirect
productofthetechnologyisacompleteplantoranymajorcomponentofa
plant,exporttoCountryGroupsD:1orE:2thedirectproductoftheplantoramajorcomponentthereof,ifsuch
foreignproduceddirectproductissubjecttonationalsecuritycontrolsasidentifiedontheU.S.
CommerceControl
ListorissubjecttoStateDepartmentcontrolsundertheU.S.MunitionsList.
5. UNITEDSTATESGOVERNMENTRESTRICTEDRIGHTS. TheenclosedProgram(i)wasdevelopedsolelyat
privateexpense;(ii)containsrestrictedcomputersoftware”submittedwithrestrictedrightsinaccordancewithsection
52.22719(a)through(d)oftheCommercial
ComputerSoftwareRestrictedRightsClauseanditssuccessors,and(iii)in
allrespectsisproprietarydatabelongingtoEnterasysand/oritssuppliers.ForDepartmentofDefenseunits,the
ProgramisconsideredcommercialcomputersoftwareinaccordancewithDFARSsection227.72023anditssuccessors,
anduse,duplication,ordisclosurebythe
Governmentissubjecttorestrictionssetforthherein.
6. DISCLAIMEROFWARRANTY. EXCEPTFORTHOSEWARRANTIESEXPRESSLYPROVIDEDTOYOUIN
WRITINGBYENTERASYS,ENTERASYSDISCLAIMSALLWARRANTIES,EITHEREXPRESSORIMPLIED,
INCLUDINGBUTNOTLIMITEDTOIMPLIEDWARRANTIESOFMERCHANTABILITY,SATISFACTORY
QUALITY,FITNESSFORAPARTICULARPURPOSE,TITLEANDNON‐
INFRINGEMENTWITHRESPECTTOTHE
PROGRAM.IFIMPLIEDWARRANTIESMAYNOTBEDISCLAIMEDBYAPPLICABLELAW,THENANYIMPLIED
WARRANTIESARELIMITEDINDURATIONTOTHIRTY(30)DAYSAFTERDELIVERYOFTHEPROGRAMTO
YOU.
7. LIMITATIONOFLIABILITY. INNOEVENTSHALLENTERASYSORITSSUPPLIERSBELIABLEFORANY
DAMAGES
WHATSOEVER(INCLUDING,WITHOUTLIMITATION,DAMAGESFORLOSSOFBUSINESS,
PROFITS,BUSINESSINTERRUPTION,LOSSOFBUSINESSINFORMATION,SPECIAL,INCIDENTAL,
CONSEQUENTIAL,ORRELIANCEDAMAGES,OROTHERLOSS)ARISINGOUTOFTHEUSEORINABILITYTO
USETHEPROGRAM,EVENIFENTERASYSHASBEENADVISEDOFTHEPOSSIBILITYOFSUCHDAMAGES.
THISFOREGOING
LIMITATIONSHALLAPPLYREGARDLESSOFTHECAUSEOFACTIONUNDERWHICH
DAMAGESARESOUGHT.
THECUMULATIVELIABILITYOFENTERASYSTOYOUFORALLCLAIMSRELATINGTOTHEPROGRAM,
INCONTRACT,TORTOROTHERWISE,SHALLNOTEXCEEDTHETOTALAMOUNTOFFEESPAIDTO
ENTERASYSBYYOUFORTHERIGHTSGRANTEDHEREIN.
ix
8. AUDITRIGHTS. YouherebyacknowledgethattheintellectualpropertyrightsassociatedwiththeProgramare
ofcriticalvaluetoEnterasysand,accordingly,Youherebyagreeto maintaincompletebooks,recordsandaccounts
showing(i)licensefeesdueandpaid,and(ii)theuse,copyinganddeploymentoftheProgram.Youalsograntto
Enterasysanditsauthorizedrepresentatives,uponreasonablenotice,therightto auditandexamineduringYour
normalbusinesshours,Yourbooks,records,accountsandhardwaredevicesuponwhichtheProgrammaybedeployed
toverifycompliancewiththisAgreement,includingtheverificationofthelicensefeesdueandpaidEnterasys
andthe
use,copyinganddeploymentoftheProgram.Enterasys’rightofexamination shallbeexercisedreasonably,ingood
faithandinamannercalculatedtonotunreasonablyinterferewithYourbusiness.Intheeventsuchauditdiscovers
noncompliancewiththisAgreement,includingcopiesoftheProgrammade,usedordeployed
inbreachofthis
Agreement,YoushallpromptlypaytoEnterasystheappropriatelicensefees.Enterasys reservestheright,tobe
exercisedinitssolediscretionandwithoutpriornotice,toterminatethislicense,effectiveimmediately,forfailureto
complywiththisAgreement.Uponanysuchtermination,Youshallimmediatelycease
alluseoftheProgramandshall
returntoEnterasystheProgramandallcopiesoftheProgram.
9. OWNERSHIP. Thisisalicenseagreementandnotanagreementforsale.Youacknowledgeandagreethatthe
Programconstitutestradesecretsand/orcopyrightedmaterialofEnterasysand/oritssuppliers.Youagreeto
implementreasonablesecuritymeasurestoprotectsuchtradesecretsandcopyrightedmaterial.Allright,titleand
interestinandtotheProgramshallremainwithEnterasysand/oritssuppliers.Allrightsnotspecificallygrantedto
YoushallbereservedtoEnterasys.
10. ENFORCEMENT. YouacknowledgeandagreethatanybreachofSections
2,4,or9ofthisAgreementbyYoumay
causeEnterasysirreparabledamageforwhichrecoveryofmoneydamageswouldbeinadequate,andthatEnterasys
maybeentitledtoseektimelyinjunctiverelieftoprotectEnterasys’rightsunderthisAgreementinadditiontoanyand
allremediesavailableatlaw.
11. ASSIGNMENT. Youmaynotassign,transferorsublicensethisAgreementoranyofYourrightsorobligations
underthisAgreement,exceptthatYoumayassignthisAgreementtoanypersonorentitywhichacquiressubstantially
allofYourstockorassets.EnterasysmayassignthisAgreementinitssolediscretion.
ThisAgreementshallbebinding
uponandinuretothebenefitoftheparties,theirlegalrepresentatives,permittedtransferees,successorsandassignsas
permittedbythisAgreement.Anyattemptedassignment,transferorsublicenseinviolationofthetermsofthis
AgreementshallbevoidandabreachofthisAgreement.
12. WAIVER.
AwaiverbyEnterasysofabreachofanyofthetermsandconditionsofthisAgreementmustbein
writingandwillnotbeconstruedasawaiverofanysubsequentbreachofsuchtermorcondition.Enterasys’failureto
enforceatermuponYourbreachofsuchtermshall
notbeconstruedasawaiverofYourbreachorpreventenforcement
onanyotheroccasion.
13. SEVERABILITY. IntheeventanyprovisionofthisAgreementisfoundtobeinvalid,illegalorunenforceable,the
validity,legalityandenforceabilityofanyoftheremainingprovisionsshallnotinanywaybeaffected
orimpaired
thereby,andthatprovisionshallbereformed,construedandenforcedtothemaximumextentpermissible.Anysuch
invalidity,illegalityorunenforceabilityinanyjurisdictionshallnotinvalidateorrenderillegalorunenforceablesuch
provisioninanyotherjurisdiction.
14. TERMINATION. EnterasysmayterminatethisAgreementimmediatelyuponYourbreachof
anyoftheterms
andconditionsofthisAgreement.Uponanysuchtermination,YoushallimmediatelyceasealluseoftheProgramand
shallreturntoEnterasystheProgramandallcopiesoftheProgram.
xi
Contents
About This Guide
Who Should Use This Guide ............................................................................................................... xv
How to Use This Guide ....................................................................................................................... xv
Related Documents ........................................................................................................................... xvi
Conventions Used in This Guide .......................................................................................................xvii
Chapter 1: Introduction
Overview ............................................................................................................................................1-1
C2K122-24 ..................................................................................................................................1-2
High-Speed Stack Connections ...................................................................................................1-3
Redundant Power Supply Capability ...........................................................................................1-3
Connectivity .......................................................................................................................................1-3
Management ......................................................................................................................................1-4
Switch Configuration Using WebView .........................................................................................1-4
Switch Configuration Using CLI Commands ...............................................................................1-4
Standards Compatibility .....................................................................................................................1-4
LANVIEW Diagnostic LEDs ...............................................................................................................1-4
Getting Help .......................................................................................................................................1-5
Chapter 2: Network Requirements
10BASE-TX Network .........................................................................................................................2-1
100BASE-TX Network .......................................................................................................................2-2
1000BASE-T Network ........................................................................................................................2-2
10GBASE-XX Network ......................................................................................................................2-2
Chapter 3: Hardware Installation
Considerations Prior to Installation ....................................................................................................3-2
Required Tools ...................................................................................................................................3-2
Unpacking the Switch ........................................................................................................................3-2
Installing Optional XFPs .....................................................................................................................3-3
Preparation ..................................................................................................................................3-3
Installing the XFP ........................................................................................................................3-4
Removing the XFP ......................................................................................................................3-4
Installing the Switch on a Flat Surface ...............................................................................................3-5
Installing the Rubber Feet ...........................................................................................................3-5
Guidelines for Installation ............................................................................................................3-6
Rack Mounting the Switch ................................................................................................................3-7
Guidelines for Rackmount Installation .........................................................................................3-8
Attaching Brackets and Installing in Rack ...................................................................................3-8
Connecting High-Speed Stacking Cables ..........................................................................................3-9
xii
Configuring Switches in a Stack ......................................................................................................3-10
About SecureStack C2 Switch Operation in a Stack .................................................................3-11
Recommended Procedures for New and Existing Stacks .........................................................3-12
Connecting AC and RPS Power ......................................................................................................3-13
Stack Initialization Overview ......................................................................................................3-15
Connecting to Console Port for Local Management ........................................................................3-16
What Is Needed .........................................................................................................................3-16
Connecting to an IBM or Compatible Device .............................................................................3-17
Connecting to a VT Series Terminal ..........................................................................................3-18
Connecting to a Modem ............................................................................................................3-19
Connecting to the Network ...............................................................................................................3-20
Connecting UTP Cables ............................................................................................................3-20
Connecting Fiber-Optic Cables to LC Ports ..............................................................................3-23
Completing the Installation ...............................................................................................................3-26
Initial Logon to Switch Management ..........................................................................................3-26
Chapter 4: Troubleshooting
Using LANVIEW .................................................................................................................................4-2
Troubleshooting Checklist ..................................................................................................................4-5
Using the Password Reset Switch .....................................................................................................4-7
Appendix A: Specifications
Switch Specifications ........................................................................................................................ A-2
Supported XFP Transceiver Interface Options ................................................................................. A-3
Console Port Pinout Assignments .................................................................................................... A-4
Regulatory Compliance ..................................................................................................................... A-4
Index
xiii
Figures
1-1 C2K122-24 Stackable Switch.................................................................................................1-2
3-1 XFP with LC Connector..........................................................................................................3-4
3-2 Chassis Bottom, Rubber Feet Placement..............................................................................3-6
3-3 Area Guidelines for Switch Installation on Flat Surface .........................................................3-7
3-4 Attaching the Rackmount Brackets........................................................................................3-8
3-5 Fastening the Switch to the Rack...........................................................................................3-9
3-6 High-Speed Stacking Cable Connections............................................................................3-10
3-7 Switch Rear View.................................................................................................................3-14
3-8 DB9 Male Console Port Pinout Assignments.......................................................................3-16
3-9 Connecting an IBM PC or Compatible .................................................................................3-17
3-10 Connecting a VT Series Terminal ........................................................................................3-18
3-11 Connecting to a Modem.......................................................................................................3-19
3-12 Connecting a UTP Cable Segment to RJ45 port .................................................................3-20
3-13 Four-Wire Crossover Cable RJ45 Pinouts for 10/100BASE-TX ..........................................3-21
3-14 Four-Wire Straight-Through Cable RJ45 Pinouts for 10/100BASE-TX................................3-22
3-15 Eight-Wire Crossover Cable RJ45 Pinouts for 10/100/1000BASE-TX.................................3-22
3-16 Eight-Wire Straight-Through Cable RJ45 Pinouts for 10/100/1000BASE-TX......................3-23
3-17 Cable Connection to LC Fiber-Optic Connectors.................................................................3-25
4-1 C2K122-24 LANVIEW LEDs ..................................................................................................4-2
4-2 LANVIEW LEDs .....................................................................................................................4-3
4-3 Password Reset Switch .........................................................................................................4-7
A-1 Console Port Pinout Assignments......................................................................................... A-4
Tables
1-1 Description of XFPs ...............................................................................................................1-3
2-1 Recommended Cable Types and Specifications ...................................................................2-3
3-1 Contents of Switch Carton .....................................................................................................3-2
4-1 Troubleshooting Checklist......................................................................................................4-5
A-1 Switch Specifications ............................................................................................................ A-2
A-2 Supported XFP Transceivers................................................................................................ A-3
A-3 XFP Fiber-Optic Specifications ............................................................................................. A-3
A-4 Recommended Cable Types and Specifications .................................................................. A-3
A-5 Compliance Standards.......................................................................................................... A-4
SecureStack C2 Installation Guide xv
About This Guide
Thisguideprovidesanoverview,installati onand troubleshootinginstructions,and
specificationsfortheEnterasys
®
SecureStackC2K12224stackableGigabitswitchwith
10GigabitEthernetuplinks.
ForinformationabouttheCommandLineInterface(CLI)setofcommandsusedto
configureandmanagetheswitch,refertotheEnterasys Networks
®
SecureStackC2
ConfigurationGuide.
Who Should Use This Guide
Thisguideisintendedforanetworkadministratorresponsibleforinstallingandsetting
upthestackableswitch.
How to Use This Guide
Readthroughthisguidecompletelytofamiliarizeyourselfwithitscontentstogainan
understandingofthefeaturesandcapabilitiesofthestackableswitch.Ageneral
knowledgeofdatacommunicationsnetworksishelpfulwhensettinguptheswitch.
Note: In this guide, the following terms are used:
Switch refers to a C2K122-24,unless otherwise noted.
XSP refers to optional small-form pluggable interface modules that plug into the front
panel port slots 25 and 26.
Important Notice
Depending on the firmware version used in the C2K122-24 switch, some features described in this
document may not be supported. Refer to the Release Notes shipped with the switch to determine
which features are supported.
Electrical Hazard: Only qualified personnel should perform installation procedures.
Riesgo Electrico: Solamente personal calificado debe realizar procedimientos de
instalacion.
Elektrischer Gefahrenhinweis: Installationen sollten nur durch ausgebildetes und
qualifiziertes Personal vorgenommen werden.
Related Documents
xvi About This Guide
ThisprefaceprovidesanoverviewofthisguideandtheSecureStackC2manualset,a
briefsummaryofeachchapteranddefinestheconventionsusedthroughoutthisguide.
Tolocateinformationconcerningvarioussubjectsinthisguide,refertothefollowing
table:
Related Documents
Thedocumentslistedbelowprovidethenecessaryinformationtoinstallandconfigure
theswitchandcanbeobtainedfromtheWorldWideWebinAdobeAcrobatPortable
DocumentFormat(PDF)atthefollowingsite:
http://www.enterasys.com/support/manuals
SecureStackC2InstallationGuideprovideshardwarespecificationsandinstructionsto
installtheswitchanditsoptions.
SecureStackC2ConfigurationGuidedescribeshowtousetheCommandLineInterface
(CLI)tosetupandmanagetheC2switch.
SecureStackC2RedundantPowerSystemC2RPSSYSInstallationGuideprovides
hardwarespecificationsandinstructionstoinstallthepowersupplyanditsoptions.
CablingGuideprovidesinformationondBlossand
cablespecifications.
Unliketheotherdocumentslistedabove,theCablingGuideisnotlistedalphabetically
onthewebsite.Instead,itislistedundertheOverviewGuideslink.
For... Refer to...
An overview of the switch features and how to
obtain technical support
Chapter 1, Introduction
Network requirements that must be met before
installing the switch
Chapter 2, Network Requirements
Instructions to install the switch on a flat surface
or in a standard 19-inch rack and configure the
switch in a stacked configuration
Chapter 3, Hardware Installation
Troubleshooting installation problems and
diagnosing network/operational problems using
the LANVIEW LEDs
Chapter 4, Troubleshooting
Specifications, environmental requirements, and
physical properties of the switch and optional
XFPs
Appendix A, Specifications
Conventions Used in This Guide
SecureStack C2 Installation Guide xvii
Conventions Used in This Guide
Thefollowingconventionsareusedinthisguide:
Note: Calls the reader’s attention to any item of information that may be of special
importance.
Caution: Contains information essential to avoid damage to the equipment.
Precaución: Contiene información esencial para prevenir dañar el equipo.
Achtung: Verweißt auf wichtige Informationen zum Schutz gegen Beschädigungen.
Electrical Hazard: Warns against an action that could result in personal injury or death
due to an electrical hazard.
Riesgo Electrico: Advierte contra una acción que pudiera resultar en lesión corporal o la
muerte debido a un riesgo eléctrico.
Elektrischer Gefahrenhinweis: Warnung vor sämtlichen Handlungen, die zu Verletzung
von Personen oder Todesfällen – hervorgerufen durch elektrische Spannung – führen
können!
Warning: Warns against an action that could result in personal injury or death.
Advertencia: Advierte contra una acción que pudiera resultar en lesión corporal o la
muerte.
Warhinweis: Warnung vor Handlungen, die zu Verletzung von Personen oder gar
Todesfällen führen können!
Conventions Used in This Guide
xviii About This Guide
SecureStack C2 Installation Guide 1-1
1
Introduction
ThischapterintroducestheC2K12224stackableswitch.
Overview
TheC2K12224isastackableswitch,whichcanbeadaptedandscaledtohelpmeetyour
networkneeds.Theswitchprovides24GigabitEthernetportsandtwo10Gigabit
Ethernetinterfaceportslots.Theswitchprovidesamanagementplatformanduplink toa
backboneforastackedgroupofup
toeightSecureStackswitches.ThetwobuiltinXFP
(10GigabitSmallFormFactorPluggable)interfaceslotsprovideyouwiththeoptionof
installing802.3aeXFPcompliantmodules10GBASEL/LR/ERfiberopticconnectionsfor
10Gbpshighspeeduplinkstothenetworkbackbone.
Theswitchalsosupportstheuse
ofaredundantDCpowersupplytohelpprevent
downtimeduetoaninternalpowersupplyfailureintheswitchorACpowersource.
Youcaninstalltheswitch
onaflatsurfaceorintoastandard19inchrackwithuser
suppliedmountinghardware,andconfiguretheswitchfunctionsusingtheWebView
application,CLIswitchingcommands,and/orSNMP.
Important Notice
Depending on the firmware version used in the switch, some features described in this document
may not be supported. Refer to the Release Notes shipped with the C2K122-24
to determine which
features are supported.
Overview
1-2 Introduction
C2K122-24
TheC2K12224(Figure 11)hasseveraltypesoffrontpanelportandrearpanel
connections,whichinclude:
•TwentyfourRJ45ports(10/100/1000Mbps,1000BASETcopperports).
•XFPslotsthatprovideyouwiththeoptionofinstallingXFPMSAcompliantmodules
for10Gigabit,10GBASEL/LR/ERfiberoptic
uplinkconnections.
•Rearpanelconnectorsforhighspeedconnectionsinastackconfiguration.
•RearpanelRedundantPowerSupplyconnectorforaredundantpowersupply
connection.TheswitchconnectstoanEnterasysC2RPSSYSusingaC2RPSPSM
Cable.
The10/100/1000 Mbps fixedfrontpanelportscanoperateineitherhalfduplexorfull
duplexmode,asdeterminedbyAutoNegotiation.
Figure 1-1 C2K122-24 Stackable Switch
Caution: The C2K122-24 is not a PoE-compliant device. Do not connect a SecureStack
C2 PoE Redundant Power System (C2RPS-POE) to the power connector. Otherwise,
damage to the device may result.
Precaución: El dispositivo C2K122-24 no cumple con el estándar PoE. No conecte una
fuente de poder redundante (RPS) SecureStack C2 PoE (C2RPS-POE) al cable de
corriente directa. De lo contrario, el dispositivo puede dañarse.
1 DB9 RS232 console port connector 6 XFP port status LEDs
2 Status LEDs 7 Two ports for stack connections
3 Twenty-four RJ45, 10/100/1000 Mbps ports 8 Password Reset switch
4 RJ45 port status LEDS 9 AC power input connector
5 Two slots for XFP interface modules 10 Redundant power supply (RPS) DC
connector
Console
1
2
23
24
25 26
CPU
UP
RPS
MGR
DOWN
13
14
11
12
25 26242322212019181716151413121110987654321
C2K122-24
ÃÅ
É
Back
Front
À Á
Â
Ä
Æ
Ç
È
Redundant Power Supply
AC LINE
100-240 VAC
50-60 Hz
1.2 A MAX
MAC ADDRESS SERIAL NO.
STACK UP STACK DOWN
Connectivity
SecureStack C2 Installation Guide 1-3
High-Speed Stack Connections
Theswitchhasrearpanelconnectorsforhighspeedconnectionsinastackconfiguration.
Thehighspeedstackingcablesusedfortheconnectionsareoptionalitemsandmustbe
orderedseparately.Therearetwotypesofcables:
•C2CABSHORTcablestoconnecttwoadjacentswitchesinthestack,and
•C2CABLONG
cabletoconnectfromthetopswitchtothebottomswitchinthestack.
ThiscablecanalsobeusedinplaceoftheC2CABSHORTcabletoconnectswitches
thataretoofarapartduetothephysicalarrangementoftheswitchesinthestack.
Redundant Power Supply Capability
Theswitchhasredundantpowersupplycapabilitywhenconnectedtoanoptional
externalredundantpowersupply(RPS).Iftheinternalpowersupplyfails,theRPS
assumestheentireloadoftheswitchwithoutinterruptingnetworktraffic.Theinternal
powersupplyandRPSeachhavetheirownACpowerconnection,whichenables
the
connectionofeachpowersupplytoadifferentACpowercircuitforadditionalACpower
sourceredundancy.
Connectivity
YoucanconnectthisswitchtoGigabitEthernetnetworksorworkstationsbywayofthe
1000BASETcompliantfixedfrontpanelRJ45connectorsandalsousetwouplinkports
thatsupportoptional10GigabitfiberopticXFPtransceiversforhighspeeduplinksto
yournetworkbackbone.
Atthetimeofthis
printing,threeversionsoftheXFPtransceiversthatareavailablefrom
EnterasysaredescribedinTable 11onpage 13.TheseXFPsmeetorexceedtheIEEE
802.3ae10Gigabitstandard.Forfiberopticandoperatingrangespecifications,referto
SupportedXFPTransceiverInterfaceOptions”onpage A3.
Table 1-1 Description of XFPs
XFP Function
10GBASE-SR-XFP Provides one 10GBASE-L Ethernet compliant LC fiber-optic multimode port
with a standard LC connector.
10GBASE-LR-XFP Provides one 10GBASE-LR Ethernet compliant LC fiber-optic single-mode
port with a standard LC connector.
10GBASE-ER-XFP Provides one 10GBASE-ER Ethernet compliant LC fiber-optic single-mode
port with a standard LC connector.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70

Enterasys Networks C2K122-24 User manual

Category
Network switches
Type
User manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI