Jackson Delta 1200 User manual

Brand: Jackson

Model: Delta 1200

Category: Dishwashers

Type: User manual

TECHNICAL MANUAL

INSTALLATION MANUAL FOR EXPORT UNITS

SERVICE MANUAL FOR DOMESTIC UNITS

FOR JACKSON MODELS:

Delta 1200

JACKSON MSC, INC.

P.O. BOX 1060

HIGHWAY 25E

BARBOURVILLE, KY. 40906

FAX: (606) 523-9196

PHONE: (606) 523-9795

www.jacksonmsc.com

CHEMICAL SANITIZING GLASSWASHER DISHMACHINE SERIES

Feb 10, 2010

P/N 07610-003-62-15 Revision D

REVISION

DATE

MADE

APPLICABLE

ECN

DETAILS

A 10-27-08 CW Initial release of manual.

B 11-10-08 GS 8074 Revised Drawings.

C 06-05-09 ARL 90605-1430-MD Updated electrical schematic.

D 02-10-10 RLC 091106-1526-CW Corrected part number on page 36

NOMENCLATURE FOR THE MODELS COVERED IN THIS MANUAL

GLASSWASHER SERIES

Delta 1200 = 24” Glasswasher

Model:

Serial No.:

Installation Date:

Service Rep. Name:

Phone No.:

SECTION DESCRIPTION PAGE

I. GENERAL

Specifications 2

Dimensions 3

II. INSTRUCTIONS SECTION

Installation Instructions 5

Electrical Connections 6

Detergent Control 7

Chemical Dispensing 8

Operating Instructions 9

Sequence of Operation 10

III. PREVENTATIVE MAINTENANCE 11

IV. TROUBLESHOOTING SECTION 13

V. MAINTENANCE INSTRUCTIONS

Replacing the Chemical Feeder Pump Motor 17

Wash Tank Heater Replacement 20

Thermostat Replacement 23

Wash Motor Replacement 25

VI. PARTS SECTION

Control Box Assembly 29

Outer Shell Assembly 31

Chemical Feeder Pump Assembly 33

Rinse Assembly 35

Wash Assembly 37

Conveyor and Drive System 39

Door Assembly 41

VII. ELECTRICAL DIAGRAM

Glasswasher 208-230 Volt, 60 Hertz, Single Phase 43

TABLE OF CONTENTS

iii

SECTION 1:

SPECIFICATION INFORMATION

Delta 1200 Technical Manual 07610-003-62-15 C

Issued: 10-27-2008 Revised: N/A

SECTION 1: SPECIFICATION INFORMATION

SPECIFICATIONS

Delta 1200

OPERATING CAPACITY (RACKS/HOUR)

GLASSES PER HOUR 1200

OPERATING CYCLE (SECONDS)

TOTAL CYCLE TIME 120

TANK CAPACITY (GALLONS) 3.0

WASH PUMP CAPACITY

WASH PUMP 55 GPM

TEMPERATURES

WASH---°F (MINIMUM) 130

RINSE---°F (MINIMUM) 75

ELECTRICAL REQUIREMENTS

WASH PUMP MOTOR HORSEPOWER 1/10

NOTE: Typical Electrical Circuit is based upon (1) 125% of the full amperage load of the machine and (2) typical fixed-

trip circuit breaker sizes as listed in the NEC 2002 Edition. Local codes may require more stringent protection than

what is displayed here. Always verify with your electrical service contractor that your circuit protection is adequate

and meets all applicable national and local codes. These numbers are provided in this manual simply for reference

and may change without notice at any given time.

RINSE TYPICAL

HEATER TOTAL ELECTRICAL

VOLTS PH HZ RATINGS AMPS CIRCUIT

208 1 60 220V/3KW 15A 15A

230 1 60 220V/3KW 15A 15A

WATER REQUIREMENTS

INLET TEMPERATURE 130°F

GALLONS PER HOUR 10.0

WATER LINE SIZE NPT (Minimum) 1/2”

DRAIN LINE SIZE NPT (Minimum) 1-1/2”

FLOW PRESSURE P.S.I. 20±5

MINIMUM CHLORINE REQUIRED (PPM) 50

MINIMUM IODIPHOR REQUIRED (PPM) 12.5

NOTE: Always refer to the machine data plate for specific electrical and water requirements. The material provided on

this page is for reference only and may be subject to change without notice.

Delta 1200 Technical Manual 07610-003-62-15 C

Issued: 10-27-2008 Revised: N/A

SECTION 1: SPECIFICATION INFORMATION

MACHINE DIMENSIONS

SECTION B-B

SCALE 0.09 : 1

6.59"

Drain

12" VERTICAL

CLEARANCE

SECTION A-A

SCALE 0.09 : 1

19.45"

29.26"

2.00" Wall Clearance

12.86"

8.64"

14.64"

25.25"

5.00"

9.50"

25.00"

Water Inlet 1/2" I.P.S. Cold

Water Inlet 1/2" I.P.S. Hot

Ø1.5 Drain Connection

6.17"

Inlet

27.41"

25.38

05700-003-60-00

SECTION 2:

INSTALLATION/OPERATION

INSTRUCTIONS

Delta 1200 Technical Manual 07610-003-62-15 C

Issued: 10-27-2008 Revised: N/A

SECTION 2: INSTALLATION/OPERATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS

VISUAL INSPECTION: Before installing the unit, check the

container and machine for damage. A damaged container is

an indicator that there may be some damage to the machine.

If there is damage to both the container and machine, do not

throw away the container. The dishmachine has been inspect-

ed and packed at the factory and is expected to arrive to you

in new, undamaged condition. However, rough handling by

carriers or others may result in there being damage to the unit

while in transit. If such a situation occurs, do not return the unit

to Jackson; instead, contact the carrier and ask them to send

a representative to the site to inspect the damage to the unit

and to complete an inspection report. You must contact the

carrier within 48 hours of receiving the machine. Also, contact

the dealer through which you purchased the unit.

UNPACKING THE DISHMACHINE: Once the machine has

been removed from the container, ensure that there are no

missing parts from the machine. This may not be obvious at

first. If it is discovered that an item is missing, contact Jackson

immediately to have the missing item shipped to you.

LEVEL THE DISHMACHINE: The dishmachine is designed to

operate while being level. This is important to prevent any

damage to the machine during operation and to ensure the

best results when washing ware. The unit comes with

adjustable bullet feet, which can be turned using a pair of

channel locks or by hand if the unit can be raised safely.

Ensure that the unit is level from side to side and from front to

back before making any connections.

PLUMBING THE DISHMACHINE: All plumbing connections

must comply with all applicable local, state, and national

plumbing codes. The plumber is responsible for ensuring that

the incoming water line is thoroughly flushed prior to connect-

ing it to any component of the dishmachine. It is necessary to

remove all foreign debris from the water line that may poten-

tially get trapped in the valves or cause an obstruction. Any

valves that are fouled as a result of foreign matter left in the

water line, and any expenses resulting from this fouling, are

not the responsibility of the manufacturer.

CONNECTING THE DRAIN LINE: The Delta 1200 glass-

washers have a gravity drain (2” NPT connection). All piping

from the machine to the drain must be a minimum 2” NPT and

shall not be reduced. There must also be an air gap between

the machine drain line and the floor sink or drain. If a grease

Packaged unit should be visually inspected for damage.

Use a pry bar and mallet to remove the hold-down blocks.

Remove any protective plastic prior to installation.

Lower

Raise

Delta 1200 Technical Manual 07610-003-62-15 C

Issued: 10-27-2008 Revised: N/A

SECTION 2: INSTALLATION/OPERATION INSTRUCTIONS

ELECTRICAL CONNECTIONS

trap is required by code, it should have a flow capacity of 5

gallons per minute.

WATER SUPPLY CONNECTION: Ensure that you have read

the section entitled “PLUMBING THE DISHMACHINE” above

before proceeding. Cold water supply must be a minimum of

70°F with a capacity of 180 gallons per hour at 8-12 PSI flow

to the glasswasher. Hot water supply must be a minimum of

130°F with a capacity of 10 gallons per hour at 20±5 PSI flow

pressure. Incoming hot and cold water service connection

(supplied by customer) must be a 1/2” pipe size minimum with

shut off valve. Install the water supply line (1/2” pipe size min-

imum) to the dishmachine using copper pipe. It is recom-

mended that a water shut-off valve be installed in the water

line between the main supply and the machine to allow access

for service.

In areas where the water pressure fluctuates or is greater than

the recommended pressure, it is suggested that a water pres-

sure regulator be installed.

Do not confuse static pressure with flow pressure. Static pres-

sure is the line pressure in a “no flow” condition (all valves and

services are closed). Flow pressure is the pressure in the fill

line when the fill valve is opened during the cycle.

It is also recommended that shock absorbers (not supplied

with the Delta 1200 units) be installed in the incoming water

lines. This prevents line hammer (hydraulic shock), induced

by the solenoid valves as they operate, from causing damage

to the equipment.

PLUMBING CHECK: Slowly turn on the water supply to the

machine after the incoming fill line and the drain line have

been installed. Check for any leaks and repair as required. All

leaks must be repaired prior to placing the machine in opera-

tion.

ELECTRICAL POWER CONNECTION: Electrical and

grounding connections must comply with the applicable por-

tions of the National Electrical Code ANSI/NFPA 70 (latest edi-

tion) and/or other electrical codes. Disconnect electrical

power supply and place a tag at the disconnect switch to indi-

cate that you are working on the circuit.

The dishmachine data plate is located on the right side of the

door. Refer to the data plate for machine operating require-

ments, machine voltage, total amperage load and serial num-

ber.

To install the incoming power lines, remove the electrical box

cover. This will require taking a phillipshead screwdriver and

removing the two (2) screws at the bottom corners and lift up

and off. Let the cover rest against the plumbing assembly.

Install conduit from the underside of machine to hole in rear of

electrical box below terminal block and ground lug. Install the

service wires (L1 & L2) to the appropriate terminals as they

are marked on the terminal block. Install the grounding wire

into the lug provided. Tighten the connections. It is recom-

mended that “DE-OX” or another similar anti-oxidation agent

be used on all power connections.

VOLTAGE CHECK: Ensure that the power switch is in the

OFF position and apply power to the dishmachine. Check the

incoming power at the terminal block and ensure it corre-

sponds to the voltage listed on the data plate. If not, contact a

qualified service agency to examine the problem. Do not run

the dishmachine if the voltage is too high or too low. Shut off

the service breaker and mark it as being for the dishmachine.

Advise all proper personnel of any problems and of the loca-

tion of the service breaker. Replace the electrical box cover

and tighten down the screws.

Terminal Block

Ground Lug

Delta 1200 Technical Manual 07610-003-62-15 C

Issued: 10-27-2008 Revised: N/A

SECTION 2: INSTALLATION/OPERATION INSTRUCTIONS

DETERGENT CONTROL

Detergent usage and water hardness are two factors that contribute greatly to how efficiently your dishmachine will operate.

Using detergent in the proper amount can become, in time, a source of substantial savings. A qualified water treatment spe-

cialist can tell you what is needed for maximum efficiency from your detergent, but you should still know some basics so you’ll

understand what they are talking about.

First, you must understand that hard water greatly effects the performance of the dishmachine. Water hardness is the amount

of dissolved calcium and magnesium in the water supply. The more dissolved solids in the water, the greater the water hard-

ness. Hard water works against detergent, thereby causing the amount of detergent required for washing to increase. As you

use more detergent, your costs for operating the dishmachine will increase and the results will decrease. The solids in hard

water also may build-up as a scale on wash and rinse heaters, decreasing their ability to heat water. Water temperature is

important in removing soil and sanitizing dishes. If the water cannot get hot enough, your results may not be satisfactory. This

is why Jackson recommends that if you have installed the machine in an area with hard water, that you also install some type

of water treatment equipment to help remove the dissolved solids from the water before it gets to the dishmachine.

Second, hard water may have you adding drying agents to your operating cycle to prevent spotting, when the real problem is

deposited solids on your ware. As the water evaporates off of the ware, the solids will be left behind to form the spotting and

no amount of drying agent will prevent this. Again, using treated water will undoubtedly reduce the occurrences of this prob-

lem.

Third, treated water may not be suitable for use in other areas of your operation. For instance, coffee made with soft water may

have an acid or bitter flavor. It may only be feasible to install a small treatment unit for the water going into the dishmachine

itself. Discuss this option with your qualified water treatment specialist.

Even after the water hardness problems have been solved, there still must be proper training of dishmachine operators in how

much detergent is to be used per cycle. Talk with your water treatment specialist and detergent vendor and come up with a

complete training program for operators. Using too much detergent has as detrimental effects as using too little. The proper

amount of detergent must be used for job. It is important to remember that certain menu items may require extra detergent by

their nature and personnel need to be made aware of this. Experience in using the dishmachine under a variety of conditions,

along with good training in the operation of the machine, can go a long way in ensuring your dishmachine operates as effi-

ciently as possible.

Certain dishmachine models require that chemicals be provided for proper operation and sanitization. Some models even

require the installation of third-party chemical feeders to introduce those chemicals to the machine. Jackson does not recom-

mend or endorse any brand name of chemicals or chemical dispensing equipment. Contact your local chemical distributor for

questions concerning these subjects.

Some dishmachines come equipped with integral solid detergent dispensers. These dispensers are designed to accommodate

detergents in a certain sized container. If you have such a unit, remember to explain this to your chemical distributor upon first

contacting them.

As explained before, water temperature is an important factor in ensuring that your dishmachine functions properly. The data

plate located on each unit details what the minimum temperatures must be for either the incoming water supply, the wash tank

and the rinse tank, depending on what model of dishmachine you have installed. These temperatures may also be followed by

temperatures that Jackson recommends to ensure the highest performance from you dishmachine. However, if the minimum

requirements are not met, the chances are your dishes will not be clean or sanitized. Remember, a dish can look clean, but it

may not be sanitized. Instruct your dishmachine operators to observe the required temperatures and to report when they fall

below the minimum allowed. A loss of temperature can indicate a much larger problem such as a failed heater or it could also

indicate that the hot water heater for your operation is not up to capacity and a larger one may need to be installed.

There are several factors to consider when installing your dishmachine to ensure that you get the best possible results from it

and that it operates at peak efficiency for many years. Discuss your concerns with your local chemical distributor and water

treatment specialist before there is a problem.

Delta 1200 Technical Manual 07610-003-62-15 C

Issued: 10-27-2008 Revised: N/A

SECTION 2: INSTALLATION/OPERATION INSTRUCTIONS

CHEMICAL DISPENSING EQUIPMENT

TO PREPARE PUMPS FOR OPERATION

The Delta 1200 is supplied with detergent, rinse additive and sanitizer dispensing chemical feeder pumps. Locate the open

ends of the chemical tubes with the tube stiffeners and place each one in the appropriate container.

A. Red Tubing = Detergent

B. Blue Tubing = Rinse Aid

C. White Tubing = Sanitizer

PRIMING CHEMICAL

FEEDER PUMPS

Chemical feeder pumps need priming when the machine is first installed, when chemicals are replenished, or if for some rea-

son the chemical lines have been removed and air is allowed to enter.

1. Verify that the proper chemical tube stiffener inlet is in the proper container.

2. Use the push buttons on the right side of control box to prime each pump.

3. To prime the pumps, hold the switch in the momentary position until chemical can be observed exiting the pump.

4. Detergent is dispensed as required during the wash tank fill. The amount of detergent may need to be increased or

decreased depending on water quality and type of detergent. It is adjusted by turning the potentiometer on the speed control

board clockwise to increase, counter-clockwise to decrease.

5. Rinse additive is dispensed proportionally into the final rinse water line. The amount of rinse aid may need to be adjusted

depending on water hardness and results. It is adjusted by turning the potentiometer on the speed control board clockwise to

increase, counter-clockwise to decrease.

6. Sanitizer either chlorine or iodine is dispensed proportionally into the final rinse water line. The amount of sanitizer may need

to be adjusted depending on concentration and the type of sanitizer used. It is adjusted by turning the potentiometer on the

speed control board clockwise to increase, counter-clockwise to decrease.

7. Warning: Some of the chemicals used in dishwashing may cause chemical burns if they come in contact with your

skin. Wear appropriate protective gear when handling these chemicals. If you do come in contact with these chemicals

flush the area with fresh water.

This equipment is not recommend for use with deionized water or other aggressive fluids. Use of deionized water or

other aggressive fluids will result in corrosion and failure of materials and components. Use of deionized water or

other aggressive fluids will void the manufacturer's warranty.

Delta 1200 Technical Manual 07610-003-62-15 C

Issued: 10-27-2008 Revised: N/A

SECTION 2: INSTALLATION/OPERATION INSTRUCTIONS

OPERATING INSTRUCTIONS

TO FILL MACHINE WITH WATER:

1. Remove wash tank strainer and place overflow stopper into fitting at the bottom of the wash tank.

2. Open incoming water shut-off valves on cold and hot water lines.

3. Place the power switch to the “FILL” position, machine will automatically fill to the correct level.

4. Check water level, it should be near top of the overflow stopper.

5. Replace wash strainer.

TO RUN THE MACHINE:

1. After filling with water, turn the power switch to the “ON” position, the rack will automatically being to rotate.

2. Place glasses on the rack.

3. When the glasses have completed the cycle, the paddle switch will be activated, turning off the water flow and conveyor

rack.

4. Remove the clean glasses which are against the paddle switch.

5. The rack will begin to rotate again.

SHUTDOWN AND CLEANING OF THE MACHINE:

1. Ensure that all ware placed on the rack is able to complete the cycle and is cleaned prior to moving the power switch to

the “OFF” position. Shut off the water supply to the unit.

2. Remove the drain boards, rack cylinder and rack. Clean before reinstalling into the machine.

3. Remove the sump and drain tank strainers. Clean completely before reinstalling into the machine.

4. Remove the stand pipe by grasping by the handle and removing from the drain tank. Clean before reinstalling into the

machine.

CAUTION: Water in the drain tank may be hot, allow the water to cool down and always remove the stand pipe

through the use of the handle. Never place your hand in the water within the drain tank.

5. Remove the curtains and wash using a mild soap and rinse with clear water. Allow to dry completely before reinstalling into

the machine.

6. Remove the wash and rinse arms. Inspect them for clogged or obstructed nozzles. Remove end caps and flush the inside

of the wash and rinse arms with clean water. Reinstall end caps when completed.

7. Wipe out the inside of the tub, removing any and all debris.

8. Reinstall all components previously removed after they have been allowed to dry.

9. Remove, clean and reinstall upper (wash) and lower (drain) strainers.

SECTION 3:

PREVENTATIVE MAINTENANCE

The dishmachines covered in this manual are designed to operate with a minimum of interaction with the operator. However,

this does not mean that some items will not wear out in time. Jackson highly recommends that any maintenance and repairs

not specifically discussed in this manual should be performed by QUALIFIED SERVICE PERSONNEL ONLY. Performing main-

tenance on your dishmachine may void your warranty if it is still in effect, so if you have a question or concern, do not hesitate

to contact Jackson.

There are many things that operators can do to prevent catastrophic damage to the dishmachine. One of the major causes of

component failure has to do with prescrapping procedures. A dishmachine is not a garbage disposal; any large pieces of mate-

rial that are put into the machine shall remain in the machine until they are either broken up (after spreading out on your ware!)

or physically removed. Strainers are installed to help catch debris, but they do no good If they are clogged. Have operators reg-

ularly inspect the pan strainers to ensure (1) that they are free of soil and debris and (2) they are laying flat in the tub.

When cleaning out strainers, do NOT beat them on waste cans. The strainers are made of metal and can be forgiving; but once

severe damage is done, it is next to impossible for the strainer to work in the way it was designed to. Wipe out strainers with

a rag and rinse under a faucet if necessary. For stubborn debris, a toothpick should be able to dislodge any obstructions from

the perforations. Always ensure that strainers are placed back in the machine before operation and that they lay flat in the tub.

You may wish to also refer to the page entitled “Detergent Control” in order to learn more about how your water hardness will

effect the performance of your machine. Hard water makes dishmachines work harder and decreases efficiency.

Again, it is important to remind operators that trying to perform corrective maintenance on the dishmachine could lead to larg-

er problems or even cause harm to the operator. If a problem is discovered; secure the dishmachine using proper shut down

procedures as listed in this manual and contact Jackson.

Some problems, however, may having nothing to do with the machine itself and no amount of preventative maintanence is

going to help. A common problem has to do with temperatures being too low. Verify that the water temperatures coming to your

dishmachine match the requirements listed on the machine data plate. There can be a variety of reasons why your water tem-

perature could be too low and you should discuss it with Jackson to determine what can be done.

By following the operating and cleaning instructions in this manual, you should get the most efficient results from your machine.

As a reminder, here are some steps to take to ensure that you are using the dishmachine the way it was designed to work:

1. Ensure that the water temperatures match those listed on the machine data plate.

2. Ensure that all strainers are in place before operating the machine.

3. Ensure that all wash and/or rinse arms are secure in the machine before operating.

4. Ensure that drains are closed/sealed before operating.

5. Remove as much soil from dishes by hand as possible before loading into racks.

6. Do not overfill racks.

7. Ensure that glasses are placed upside down in the rack.

8. Ensure that all chemicals being injected to machine have been verified as being at the correct concentrations.

9. Clean out the machine at the end of every workday as per the instructions in the manual.

10. Always contact Jackson whenever a serious problem arises.

11. Follow all safety procedures, whether listed in this manual or put forth by local, state or national codes/regulations.

Delta 1200 Technical Manual 07610-003-62-15 C

Issued: 10-27-2008 Revised: N/A

SECTION 3: PREVENTATIVE MAINTENANCE

PREVENTATIVE MAINTENANCE

SECTION 4:

TROUBLESHOOTING

Delta 1200 Technical Manual 07610-003-62-15 C

Issued: 10-27-2008 Revised: N/A

SECTION 4: TROUBLESHOOTING

COMMON PROBLEMS

Inspection, testing and repair of electrical equipment should only be performed by a qualified service tech-

nician. Many of the tests require that the unit have power to it and live electrical components be exposed.

USE EXTREME CAUTION WHEN TESTING THE MACHINE.

Problem: Dish machine will not run, no voltage at wash relay terminals L1 and T1.

1. Electrical power not installed to machine, service (main) power disconnect off. Ensure electrical wiring is run to machine and

service (main) disconnect is on.

2. Branch circuit breaker tripped or fuse is blown. Reset or replace as required. Have an electrician check machine amp draw

if problem keeps occuring.

3. Loose or broken connection to dish machine. Tighten, replace or repair as required.

Problem: Machine cycles continuously.

1. Limit switch actuator is loose or has fallen off. Reassemble/bend metal lever if necessary.

2. Faulty limit switch. Replace switch.

Problem: Machine will not fill, other functions work.

1. No water supply to machine. Ensure that water is hooked up properly to machine and that it is turned on.

2. Faulty Hot Water solenoid valve diaphragm or coil. Replace diaphragm and clean out valve. Measure continuity on coil, if

there is none, replace the coil.

3. Faulty float switch. Ohm out the switch to ensure that upper and lower floats are working. If not, check float wiring to see if

it is correct; if so, replace float.

Problem: Machine fills continuously even with no power to the dish machine.

1. Solenoid valve jammed/stuck in the open position. Check diaphragm and coil, replace as required.

2. Faulty float switch. Ohm out the switch to ensure that upper and lower floats are working. If not, check float wiring to see if

it is correct; if so, replace float switch.

Problem: Wash motor does not run, other functions work.

1. Loose wire connection to limit switch or relay. Tighten wires.

2. Faulty pump motor. Replace pump motor.

3. Mechanical binding in the pump. If motor has correct incoming voltage, and the overload is tripping, repair or replace the

pump.

Problem: Wash motor does not run; other functions work.

1. High or low voltage problem. Check voltage at motor and at power terminal block. Ensure it meets the electrical voltage

specifiactions for the dish machine.

2. Faulty limit switch. Replace limit switch.

Problem: Wash motor runs continuously.

1. Wash relay welded closed. Turn machine off. If wash relay does not release, replace.

Problem: Low water pressure.

1. Water level is too low. Ensure that incoming water line pressure meets the requirements on dish machine data plate.

2. Wash arms clogged. Remove wash arms and clean.

3. Obstruction in pump housing. Disassemble and clear.

4. O-ring at wash tank drain cut or missing. Replace.

Delta 1200 Technical Manual 07610-003-62-15 C

Issued: 10-27-2008 Revised: N/A

SECTION 4: TROUBLESHOOTING

COMMON PROBLEMS

Problem: Low wash water pressure at wash arm spray nozzles.

1. Pump impeller worn or broken. Replace pump.

2. Clogged jets in wash arms. Clean out wash arms.

3. Float stuck on float switch. Remove, clean and reinstall float switch.

4. Water level too low in the wash tank. Ensure that the incoming water line flow pressure meets the requirements on the dish-

machine data plate.

Problem: Machine keeps tripping service breaker.

1. Power supply shorted to ground. Check for loose wires/burned connection. Replace or repair as required.

2. Pump impeller jammed. Disassembly and remove obstruction.

3. Wash pump motor faulty. Check motor voltage and amp draw.

4. Service breaker too small. Replace with correctly sized breaker.

Problem: Machine will not hold water.

1. Drain stopper not in place. Set drain stopper correctly in drain.

2. Drain fitting O-ring cut or missing. Replace O-ring.

3. Drain stopper bent or deformed. Replace.

Problem: Sanitizer pump runs continuously.

1. Shorted prime switch. If there is not line voltage between BLACK/YELLOW and ORANGE/BLUE wires to prime switch,

replace.

2. Faulty speed control board. Check operation of board. If not working properly, replace.

Problem: Sanitizer pump does not run during cycle, but runs when primed. Even when turntable is off.

1. Loose or broken wire. Replace or tighten.

2. Faulty speed control board. Check operation of board. If not working properly, replace.

3. Faulty prime switch. Check continuity through each pole of the speed control board. If it fails, replace the speed control board.

Problem: Prime switch does not activate sanitizer pump.

1. Faulty prime switch. With the prime switch in the prime position, check for voltage between BLACK/YELLOW and

ORANGE/BLUE wires. If line voltage, replace switch.

2. Loose wire to prime switch. Tighten wire connection.

Problem: Sanitizer pump doesn't run during cycle or through prime switch.

1. Loose motor terminal wires. Tighten connections.

Problem: Sanitizer pump doesn't run during cycle or through prime switch.

1. Faulty sanitizer pump motor. If you read line voltage at the sanitizer motor terminals during the sanitizer feed cycle, replace

the motor.

2. Faulty prime switch. Check the continuity through each pole of the switch. If faulty, replace the speed control board.

Problem: Detergent not feeding, rinse aid feeds okay.

1. Faulty speed control board. Check operation of board. If not working properly, replace.

2. Defective hose or squeeze tube. Replace hose or squeeze tube as needed.

3. Machine not in fill mode. Normal operation.

Delta 1200 Technical Manual 07610-003-62-15 C

Issued: 10-27-2008 Revised: N/A

SECTION 4: TROUBLESHOOTING

COMMON PROBLEMS

Problem: Rinse aid pump not feeding, detergent feeds okay.

1. Faulty speed control board. Check operation of board. If not working properly, replace.

2. Defective hose or squeeze tube. Replace hose or squeeze tube as needed.

Problem: Wash heater does not work. (Note: push wash heater contactor bar down and take amperage reading. Amps

should be correct as stated on the dish machine data plate).

1. If no amp draw, check wash heater for continuity. If open or shorted, replace the heater. If closed, replace the heater con-

tactor.

2. Wash heater relay will not energize (no voltage at contactor coil). Check for continuity at wash thermostat. If open, replace.

3. Low voltage problem. Check incoming voltage to ensure it as what the data plate calls for.

Page is loading ...

Jackson Delta 1200 User manual

Brand: Jackson

Model: Delta 1200

Category: Dishwashers

Type: User manual

Download PDF

report

Jackson Delta 1200 User manual

Jackson Delta 1200 User manual

Related papers

Other documents