Faber Dama 30 SSV with VAM Installation guide

Page is loading ...

2

READ AND SAVE THESE INSTRUCTIONS BEFORE YOU START

INSTALLING THIS RANGEHOOD

WARNING: - TO REDUCE THE RISK OF A RANGE TOP GREASE FIRE:

a) Never leave surface units unattended at high settings. Boilovers cause smoking and

greasy spillovers that may ignite. Heat oils slowly on low or medium setting.

b)AlwaysturnhoodONwhencookingathighheatorwhenambeingfood(i.e.Crepes

Suzette, Cherries Jubilee, Peppercorn Beef Flambé).

c) Clean ventilating fans frequently. Grease should not be allowed to accumulate on fan

orlter.

d) Use proper pan size. Always use cookware appropriate for the size of the surface element.

WARNING: - TO REDUCE THE RISK OF INJURY TO PERSONS IN THE EVENT OF A

RANGE TOP GREASE FIRE, OBSERVE THE FOLLOWING*:

a)SMOTHERFLAMESwithaclose-ttinglid,cookiesheet,ormetaltray,thenturnofftheburner.

BECAREFULTOPREVENTBURNS.IftheamesdonotgooutimmediatelyEVACUATE

AND CALL THE FIRE DEPARTMENT.

b) NEVER PICK UP A FLAMING PAN - You may be burned.

c) DO NOT USE WATER, including wet dishcloths or towels - a violent steam explosion will

result.

d) Use an extinguisher ONLY if:

1. You know you have a Class ABC extinguisher, and you already know how to operate it.

2. Thereissmallandcontainedintheareawhereitstarted.

3. Theredepartmentisbeingcalled.

4. Youcanghttherewithyourbacktoanexit.

* Based on "Kitchen Firesafety Tips" published by NFPA

WARNING - TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, do not use this

fan with any solid-state speed control device.

WARNING - TO REDUCE THE RISK OF FIRE, ELECTRICAL SHOCK, OR INJURY TO

PERSONS, OBSERVE THE FOLLOWING:

1. Use this unit only in the manner intended by the manufacturer. If you have any

questions, contact the manufacturer.

2. Before servicing or cleaning unit, switch power off at service panel and lock the

service disconnecting means to prevent power from being switched on acciden-

tally. When the service disconnecting means cannot be locked, securely fasten a

prominent warning device, such as a tag, to the service panel.

CAUTION: For General Ventilating Use Only. Do Not Use To Exhaust Hazardous or

Explosive Materials and Vapors.

WARNING - TO REDUCE THE RISK OF FIRE, ELECTRICAL SHOCK, OR INJURY TO

PERSONS, OBSERVE THE FOLLOWING:

1. InstallationWorkAndElectricalWiringMustBeDoneByQualiedPerson(s)InAccor-

dance With All Applicable Codes And Standards, Including Fire-Rated Construction.

2. Sufcientairisneededforpropercombustionandexhaustingofgasesthrough

theue(chimney)offuelburningequipmenttopreventbackdrafting.Followthe

heating equipment manufacturer's guideline and safety standards such as those

publishedbytheNational FireProtectionAssociation(NFPA),andtheAmerican

SocietyforHeating,RefrigerationandAirConditioningEngineers(ASHRAE),and

the local code authorities.

3

3. When cutting or drilling into wall or ceiling, do not damage electrical wiring and

other hidden utilities.

4. Ducted fans must always be vented to the outdoors.

ALL WALL AND FLOOR OPENINGS WHERE THE RANGEHOOD IS INSTALLED MUST

BE SEALED.

This rangehood requires at least 24" of clearance between the bottom of the rangehood

and the cooking surface or countertop. This hood has been approved by UL at this distance from

the cooktop.

This minimum clearance may be higher depending on local building codes. For gas cooktops and

combination ranges, a minimum of 30" is recommended and may be required.

Overhead cabinets on both sides of this unit must be a minimum of 18" above the cooking surface

or countertop. Consult the cooktop or range installation instructions given by the manufacturer

before making any cutouts.

MOBILE HOME INSTALLATION The installation of this rangehood must conform to the Manufactured

Home Construction and Safety Standards, Title 24 CFR, Part 3280 (formerly Federal Standard

for Mobile Home Construction and Safety, Title 24, HUD, Part 280). See Electrical Requirements.

• Venting system MUST terminate outside the home.

• DO NOT terminate the ductwork in an attic or other enclosed space.

• DO NOT use 4" laundry-type wall caps.

• Flexible-type ductwork is not recommended.

• DO NOT obstruct the ow of combustion and ventilation air.

• Failure to follow venting requirements may result in a re.

WARNING

!

VENTING REQUIREMENTS

Determine which venting method is best for your application. Ductwork can extend either through the

wall or the roof.

The length of the ductwork and the number of elbows should be kept to a minimum to provide efcient

performance. The size of the ductwork should be uniform. Do not install two elbows together. Use

duct tape to seal all joints in the ductwork system. Use caulking to seal exterior wall or oor opening

around the cap.

Flexible ductwork is not recommended. Flexible ductwork creates back pressure and air turbulence

that greatly reduces performance.

Make sure there is proper clearance within the wall or oor for exhaust duct before making cutouts.

Do not cut a joist or stud unless absolutely necessary. If a joist or stud must be cut, then a supporting

frame must be constructed.

WARNING - To Reduce The Risk Of Fire, Use Only Metal Ductwork.

CAUTION-Toreduceriskofreandtoproperlyexhaustair,besuretoductairoutside–Do

not vent exhaust air into spaces within walls or ceilings or into attics, crawl spaces, or garages.

Cold Weather installations

An additional back draft damper should be installed to minimize backward cold air ow and a

nonmetallic thermal break should be installed to minimize conduction of outside temperatures as

part of the vent system. The damper should be on the cold air side of the thermal break. The break

should be as close as possible to where the vent system enters the heated portion of the house.

4

• Electrical ground is required on this rangehood.

• If cold water pipe is interrupted by plastic, nonmetallic gaskets or other materials, DO

NOT use for grounding.

• DO NOT ground to a gas pipe.

• DO NOT have a fuse in the neutral or grounding circuit. A fuse in the neutral or

grounding circuit could result in electrical shock.

• Check with a qualied electrician if you are in doubt as to whether the rangehood is

properly grounded.

• Failure to follow electrical requirements may result in a re.

WARNING

!

StateofCaliforniaProposition65Warning(USonly)

WARNING

This product contains chemicals known to the State of California to cause cancer and birth

defects or other reproductive harm.

For more information go to www.P65Warnings.ca.gov

ELECTRICAL REQUIREMENTS

A 120 volt, 60 Hz AC-only electrical supply is required on a separate 15 amp fused circuit.

A time-delay fuse or circuit breaker is recommended. The fuse must be sized per local

codes in accordance with the electrical rating of this unit as specied on the serial/rating

plate located inside the unit near the eld wiring compartment.

Page is loading ...

6

2.2

2.1

10

7.2.1

12a

12b

12d

MAIN PARTS

Components

Ref. Qty. Product Components

1 1 Hood Body, complete with: Con-

trols, Light, Filters, Blower.

2 1 Telescopic Chimney comprising:

2.1 1 Upper Section

2.2 1 Lower Section

10 1 Damper ø 5 7/8"

Ref. Qty. Installation Components

7.2.1 2 Upper Chimney Section Fixing

Brackets

12a 6 Screws 3/16" x 1 3/4"

12b 2 Screws 1/8" x 7/16"

12d 2 Screws 1/8" x 5/16"

Qty. Documentation

1 Instruction Manual

Available Accessories

Parts needed

- 6" Round Metal ductwork

Direct Connect Wiring Box sku # WIREBOX

High Ceiling Chimney Kit - Upper and Lower Chimney Flue to replace the original ue's to

t up to 11' ceilings - sku# HIGH3

Ductless Kit - Includes Ductless Diverter, Charcoal Filters - sku# DUCT4

Activated Charcoal Filter Accessory - sku# FILTER2

Wireless Remote Control Accessory - REMCTRL2

1

"When used in recirculation mode, to Reduce the Risk of Fire and Shock use only

Ductless Kit and Activated Charcoal Filter listed in Available Accessories below. "

7

Install Damper that is included with the Hood before connect-

ing to the ductwork.

Only for Ducted Venting Installation







H

I



Remove the lters one at a time, supporting them with one

hand and turning the safety knobs (pull and turn).

1

Choose your ducting method

Non Ducted - RecirculationDucted Venting Installation

Requires

purchase of

Activated

Charcoal

Accessory

Horizontal

Vertical

6"

8

2

Draw a vertical line on the supporting wall as high as practical, at the center of the area in which

the hood will be installed.

Draw a horizontal line at where the bottom edge of the hood will be located as indicated in the gure

that is a minimum of 24" electric and 30" gas cooking surface clearance.

3

Draw a horizontal line where indicated at the bottom edge of the vent hood at the desired height above

the cooking surface.

Place a bracket 7.2.1 on the wall as shown about 1/8" from the ceiling or upper limit, aligning the

centers(notch) with the vertical reference line and mark the wall at the centers of the holes in the bracket.

Place the second bracket 7.2.1 on the wall as shown, below the rst bracket, at the height of the

upper chimney section supplied and aligning the centers(notch) with the vertical line.

Attention: If the position of the second bracket (7.2.1,) below the rst bracket is less than 19 1/2" from

the horizontal reference line, then the second bracket cannot be xed.

Mark the wall at the centers of the holes in the bracket and mark the point 1 and 2 for the Hood Body

installation as show (16 9/16" from the horizontal line and 4 9/16" from the vertical line).

Drill ø 5/16" holes at all the centers points marked (point 1,2,3,4,5,6) as shown.











x6











x6







´

´

´

!

´

´ ´

´

7.2.1

2.1

9

8

4

5

6

7

Installation screws provided must be secured

with wall plugs (purchase separately).

Use a level to insure that hood body is level and then

fully secure the two screws.

Hook the hood body onto the hood body xing screws.

9

Install Roof or Wall

Cap purchased

separately. Con-

nect the 6" metal

ductwork to the

Roof or Wall Cap

and then attach

ductwork.

Vertical or Horizontal

Ducting Installation

Tighten the 2 screws 12a as shown.

L = 2x

OK!

3/16 “

12a

Insert not completely the two screws 12a supplied

in the hood body xing holes as shown.

I = 6x

12a

10

L = 4x

Install the 2 xing brackets 7.2.1 to the middle and

upper holes and secure with screws 12a as shown.

11

12

2.1

N = 4x

Slightly widen

the two sides

of the upper

chimney and

hook them

behind the

brackets 7.2.1,

making sure

that they are

well seated.

Secure the sides to the brackets by using the 2

screws 12b.

12a

N = 2x

2.2

2.1

14

Slightly widen the two

sides of the the lower

chimney hood and hook

them between

the upper section and the

wall, making sure that they

are properly housed.

Fix the the

lower chim-

ney hood

laterally to

the hood

body using

the 2 screws

12d supplied.

13

12b = 2x

12d = 2x

11

17 18

19

2.1

Fix the Ductless Diverter with two screws 12a supplied

as shown.

Slightly widen

the two sides of

the upper chim-

ney and hook

them behind

the brackets

and connect to

the Ductless

Diverter, mak-

ing sure that

they are well

seated.

15 16

¡

12a

Only for the recirculation version, connect the hood

to the Air outlet.

Fix the lower Bracket 7.2.1 with two screws 12a

supplied as shown.

Non-Ducted Recirculation Option

N = 4x

12b 2X

Secure the sides to the brackets by using the 2

screws 12b.

12

Direct Connect Wiring Box

Accessory sku # WIREBOX

(purchased separately)

Created by

-

Denomination

-

Lang EN

Sheet

1

/1

Modif.by

Approved by

Approval date

Doc. status

Drawing N.

NEW_DRAWING_BOX

Rev

01

ELECTRICAL INSTALLATION WITH CONNECTION

CABLE

GROUNDING INSTRUCTIONS This appliance must be

grounded. In the event of an electrical short circuit, grounding

reduces the risk of electric shock by providing an escape

wire for the electric current. This appliance is equipped

with a cord having a grounding wire with a grounding plug.

The plug must be plugged into an outlet that is properly

installed and grounded.

WARNING - Improper grounding can result in a risk of

electric shock.

Consult a qualied electrician if the grounding instructions

are not completely understood, or if doubt exists as to

whether the appliance is properly grounded.

Do not use an extension cord. If the power supply cord is

too short, have a qualied electrician install an outlet near

the appliance.

ELECTRICAL INSTALLATION WITH

OPTIONAL WIRING BOX

For Permanent wiring Installation-Use only

with Listed rangehood Wiring Box kit

sku # WIREBOX, manufactured by Faber.

20

For Non-Ducted Recirculation

Option

Attach a

charcoal

lter in the

correct

position and

block it by

the xing

hooks as

shown.

Unlock the xing hooks (towards the back of the

hood) to remove.

Max. 33 7/16”

Required Activated Charcoal Filter

Accessory - sku # - FILTER2

13

N = 2x

2.2

2.1

21 22

Slightly widen the two

sides of the the lower

chimney hood and hook

them between

the upper section and the

wall, making sure that they

are properly housed.

Fix the the

lower chim-

ney hood

laterally to

the hood

body using

the 2 screws

12d supplied.

12d = 2x

14

USE AND CARE INFORMATION

T1 T2 T3 T4 L

LT1 T2 T3 T4

For Best Results

Start the rangehood several minutes before cooking to develop proper airow. Allow the

rangehood to operate for several minutes after cooking is complete to clear all smoke and

odors from the kitchen.

T1. Fan o button:turn the blower O. The fan can be operated by pressing any of the fan setting buttons.

Hold down this button for 2 seconds to activate Delay o function which will keep the fan on for 15

minutes and automatically shut o.

T2. Fan settings buttons: Low speed.

T3. Fan settings buttons: Medium speed.

T4. Fan settings buttons: High speed / Intensive speed.

Hold down the button for 2 seconds to activate the intensive speed, which is timed to run for 6

minutes. At the end of this time it will automatically return to the speed set before.Suitable to deal

with maximum levels of cooking fumes.

L. Light button: On/O switch for the lights.

NOTE: If your product has had a CFM adjustment, refer to the CFM adjustment manual for the infor-

mation. Some motor speeds or functions may be reduced.

15

Cleaningmetalgreaselters

The lters must be cleaned every 2 months of opera-

tion, or more frequently for particularly heavy usage,

and can be washed in a dishwasher.The metal grease

lters should be cleaned frequently in hot detergent

solution or washed in the dishwasher. Stainless steel

cleaner should be used on stainless rangehoods.

Abrasives and scouring agents can scratch stain-

less steel nishes and should not be used to clean

nished surface. Remove all water or any other liquid

from washing before re-installing lters.

• Remove the lters one at a time, supporting

them with one hand and turning the safety

knobs (pull and turn).

• Wash the lters, taking care not to bend them.

Allow them to dry before retting.

• Replace them and x them using the safety

knobs provided (pull and turn).

• No water can be present in lters before install-

ing back in hood.

Replacing Activated Charcoal Filter

The lter is not washable and cannot be regenerated,

and must be replaced approximately every 4 months of

operation, or more frequently for particularly heavy usage.

• Remove the Filters one at a time, pushing them

towards the back of the unit and at the same time

pulling downward.

• Remove the saturated charcoal lter by releasing the

xing hooks.

• Fit the new lter and fasten it in its correct position.

• Replace, taking care to ensure that the handle faces

forwards.

• CAUTION: When used in recirculation mode, to Re-

duce the Risk of Fire and Shock use only conversion

kit Model FILTER2.

Lighting unit

• Remove the snap-on lamp cover

by levering it from under the metal

ring, supporting it with one hand.

• Replace the lamp with a new one

of the same type, making sure that

you insert the two pins properly into

the housings on the lamp holder.

• Replace the snap-on lamp cover.

Gu10 self-ballasted led

lamps – listed in ac-

cordance with

ul 1993/nmx-

j-578/1-ance/

csa c22.2 No.

1993

Page is loading ...

17

January 4, 2016

FABER CONSUMER WARRANTY & SERVICE

All Faber products are warranted against any defect in materials or workmanship for the original purchaser

for a period of 1 year from the date of original purchase (requires proof of purchase). This warranty covers

labor and replacement parts. Faber, at its option, may repair or replace the product or components

necessary to restore the product to good working condition. To obtain warranty service, contact the dealer

from whom you purchased the range hood, or the local Faber distributor. If you cannot identify a local Faber

distributor, contact us at (508) 358-5353 for the name of a distributor in your area.

The following is not covered by Faber's warranty:

1. Service calls to correct the installation of your range hood, to instruct you how to use your range hood, to

replace or repair house fuses or to correct house wiring or plumbing.

2. Service calls to repair or replace range hood light bulbs, fuses or filters. Those consumable parts are

excluded from warranty coverage.

3. Repairs when your range hood is used for other than normal, single-family household use.

4. Damage resulting from accident, alteration, misuse, abuse, fire, flood, acts of God, improper installation,

installation not in accordance with electrical or plumbing codes or Faber documentation, or use of products

not approved by Faber.

5. Replacement parts or repair labor costs for units operated outside the United States or Canada, including

any non-UL or C-UL approved Faber range hoods.

6. Repairs to the hood resulting from unauthorized modifications made to the range hood.

7. Expenses for travel and transportation for product service in remote locations and pickup and delivery

charges. Faber range hoods should be serviced in the home.

THIS WARRANTY DOES NOT ALLOW RECOVERY OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, INCLUDING, WITHOUT

LIMITATION, DIRECT, INDIRECT, INCIDENTAL, SPECIAL OR CONSEQUENTIAL DAMAGES, PERSONAL INJURY/WRONGFUL

DEATH OR LOST PROFITS FABER WARRANTY IS LIMITED TO THE ABOVE CONDITIONS AND TO THE WARRANTY PERIOD

SPECIFIED HEREIN AND IS EXCLUSIVE. EXCEPT AS EXPRESSLY SPECIFIED IN THIS AGREEMENT, FABER DISCLAIMS ALL

EXPRESS OR IMPLIED CONDITIONS, REPRESENTATIONS, AND WARRANTIES INCLUDING, WITHOUT LIMITATION, ANY

IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE

.

This warranty gives you specific legal rights that may vary from state to state.

Model#: ______________________________ Serial #: _____________________________

Page is loading ...

49

Esta garantia Aplica para USA y Canada

January 4, 2016

FABER CONSUMER WARRANTY & SERVICE

All Faber products are warranted against any defect in materials or workmanship for the original purchaser

for a period of 1 year from the date of original purchase (requires proof of purchase). This warranty covers

labor and replacement parts. Faber, at its option, may repair or replace the product or components

necessary to restore the product to good working condition. To obtain warranty service, contact the dealer

from whom you purchased the range hood, or the local Faber distributor. If you cannot identify a local Faber

distributor, contact us at (508) 358-5353 for the name of a distributor in your area.

The following is not covered by Faber's warranty:

1. Service calls to correct the installation of your range hood, to instruct you how to use your range hood, to

replace or repair house fuses or to correct house wiring or plumbing.

2. Service calls to repair or replace range hood light bulbs, fuses or filters. Those consumable parts are

excluded from warranty coverage.

3. Repairs when your range hood is used for other than normal, single-family household use.

4. Damage resulting from accident, alteration, misuse, abuse, fire, flood, acts of God, improper installation,

installation not in accordance with electrical or plumbing codes or Faber documentation, or use of products

not approved by Faber.

5. Replacement parts or repair labor costs for units operated outside the United States or Canada, including

any non-UL or C-UL approved Faber range hoods.

6. Repairs to the hood resulting from unauthorized modifications made to the range hood.

7. Expenses for travel and transportation for product service in remote locations and pickup and delivery

charges. Faber range hoods should be serviced in the home.

THIS WARRANTY DOES NOT ALLOW RECOVERY OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, INCLUDING, WITHOUT

LIMITATION, DIRECT, INDIRECT, INCIDENTAL, SPECIAL OR CONSEQUENTIAL DAMAGES, PERSONAL INJURY/WRONGFUL

DEATH OR LOST PROFITS FABER WARRANTY IS LIMITED TO THE ABOVE CONDITIONS AND TO THE WARRANTY PERIOD

SPECIFIED HEREIN AND IS EXCLUSIVE. EXCEPT AS EXPRESSLY SPECIFIED IN THIS AGREEMENT, FABER DISCLAIMS ALL

EXPRESS OR IMPLIED CONDITIONS, REPRESENTATIONS, AND WARRANTIES INCLUDING, WITHOUT LIMITATION, ANY

IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE

.

This warranty gives you specific legal rights that may vary from state to state.

Model#: ______________________________ Serial #: _____________________________

GARANTÍA Y SERVICIO AL CONSUMIDOR FABER

Todos los productos Faber están garantizados contra cualquier defecto de materiales o mano de obra para el

comprador original por un período de 1 año a partir de la fecha de compra original (requiere prueba de compra).

Esta garantía cubre mano de obra y piezas de repuesto. Faber, a su elección, puede reparar o reemplazar el

producto o componentes necesarios para restaurar el producto en buenas condiciones de trabajo. Para obtener

el servicio de garantía, póngase en contacto con el distribuidor de quien adquirió la campana extractora o con el

distribuidor local de Faber. Si no puede identicar a un distribuidor local de Faber, comuníquese con nosotros al

(508) 358-5353 para obtener el nombre de un distribuidor en su área.

Lo siguiente no está cubierto por la garantía de Faber:

1. Llamadas de servicio para corregir la instalación de su campana extractora, para instruirle sobre cómo usar su

campana extractora, para reemplazar o reparar fusibles de la casa o para corregir el cableado de la casa o la

plomería.

2. Llamadas de servicio para reparar o reemplazar las bombillas, fusibles o ltros de la campana extractora. Estas

partes de consumibles están excluidas de la cobertura de la garantía.

3. Reparaciones, cuando su campana extractora se utiliza para uso doméstico distinto al normal.

4. Daños resultantes de accidente, alteración, mal uso, abuso, incendio, inundación, eventos naturales, instala-

ción incorrecta, instalación no conforme a los códigos eléctricos o de plomería o la documentación de Faber, o

uso de productos no aprobados por Faber.

5. Piezas de repuesto o costos de mano de obra de reparación para unidades operadas fuera de los Estados

Unidos o Canadá, incluyendo cualquier campana de cocina Faber no aprobada por UL o C-UL.

6. Reparaciones a la campana resultantes de modicaciones no autorizadas a la misma.

7. Gastos de viaje y transporte para el servicio del producto en lugares remotos, y gastos de recogida y entrega.

Las campanas de cocina Faber deben ser reparadas en el hogar.

ESTA GARANTÍA NO PERMITE LA RECUPERACIÓN DE DAÑOS INCIDENTALES O CONSECUENTES, IN-

CLUYENDO, SIN LIMITACIÓN, DAÑOS DIRECTOS, INDIRECTOS, INCIDENTALES, ESPECIALES O CONSE-

CUENTES, LESIONES PERSONALES O MUERTE INCORRECTA O BENEFICIOS PERDIDOS. LA GARANTÍA

DE FABER SE LIMITA A LAS CONDICIONES ANTERIORES Y AL PERÍODO DE GARANTÍA ESPECIFICADO

AQUÍ Y ES EXCLUSIVA. EXCEPTO DADO LO EXPRESAMENTE ESPECIFICADO EN ESTE ACUERDO, FABER

RENUNCIA A TODAS LAS CONDICIONES, REPRESENTACIONES Y GARANTÍAS EXPRESAS O IMPLÍCITAS

INCLUYENDO, SIN LIMITACIÓN, CUALQUIER GARANTÍA IMPLÍCITA DE COMERCIABILIDAD O ADECUACIÓN

PARA UN PROPÓSITO PARTICULAR.

Esta garantía le otorga derechos legales especícos que pueden variar de estado a estado.

Modelo: ____________________________ Número de serie ____________________________

4 de enero de 2016

Page is loading ...

Faber Dama 30 SSV with VAM Installation guide

This manual is also suitable for

Faber Dama 30 SSV with VAM Installation guide

in other languages

Related papers

Other documents