Zanussi ZGG75524XA User manual

Page is loading ...

Contents

Safety information 16

Safety instructions 17

Product description 19

Daily use 20

Hints and tips 21

Care and cleaning 21

Troubleshooting 22

Installation 24

Technical information 26

Energy efficiency 27

Subject to change without notice.

Safety information

Before the installation and use of the appliance, carefully read the

supplied instructions. The manufacturer is not responsible if an

incorrect installation and use causes injuries and damages.

Always keep the instructions with the appliance for future

reference.

Children and vulnerable people safety

• This appliance can be used by children aged from 8 years and

above and persons with reduced physical, sensory or mental

capabilities or lack of experience and knowledge if they have

been given supervision or instruction concerning use of the

appliance in a safe way and understand the hazards involved.

• Do not let children play with the appliance.

• Keep all packaging away from children.

• Keep children and pets away from the appliance when it

operates or when it cools down. Accessible parts are hot.

• If the appliance has a child safety device, we recommend you

activate it.

• Cleaning and user maintenance shall not be made by children

without supervision.

• Children of less than 3 years should be kept away unless

continuously supervised.

General Safety

• The appliance and its accessible parts become hot during use.

Do not touch the heating elements.

• Do not operate the appliance by means of an external timer or

separate remote-control system.

16 www.zanussi.com

• Unattended cooking on a hob with fat or oil can be dangerous

and may result in fire.

• Never try to extinguish a fire with water, but switch off the

appliance and then cover flame e.g. with a lid or a fire blanket.

• Do not store items on the cooking surfaces.

• Metallic objects such as knives, forks, spoons and lids should

not be placed on the hob surface since they can get hot.

• Do not use a steam cleaner to clean the appliance.

• If the supply cord is damaged, it must be replaced by the

manufacturer, an authorized Service or similarly qualified

persons in order to avoid a hazard.

• Where the appliance is directly connected to the power supply,

an all-pole isolating switch with a contact gap is required.

Complete disconnection in compliance with the conditions

specified in overvoltage category III must be guaranteed. The

earth cable is excluded from this.

• When you route the mains cable, make sure that the cable

doesn't come into direct contact (for example using insulating

sleeving) with parts that can reach temperatures of more than

50°C above room temperature.

Safety instructions

This appliance is suitable for the following

markets: BE LU

Installation

WARNING!

Only a qualified person must install

this appliance.

• Remove all the packaging.

• Do not install or use a damaged appliance.

• Obey the installation instruction supplied

with the appliance.

• Keep the minimum distance from the other

appliances and units.

• Always be careful when you move the

appliance because it is heavy. Always wear

safety gloves.

• Seal the cut surfaces with a sealant to

prevent moisture to cause swelling.

• Protect the bottom of the appliance from

steam and moisture.

• Do not install the appliance adjacent to a

door or under a window. This prevents hot

cookware to fall from the appliance when the

door or the window is opened.

• If the appliance is installed above drawers

make sure that the space, between the

bottom of the appliance and the upper

drawer, is sufficient for air circulation.

• The bottom of the appliance can get hot.

Make sure to install a non-combustile

separation panel under the appliance to

prevent access to the bottom.

Electrical Connection

WARNING!

Risk of fire and electrical shock.

• All electrical connections should be made by

a qualified electrician.

• The appliance must be earthed.

www.zanussi.com 17

• Before carrying out any operation make sure

that the appliance is disconnected from the

power supply.

• Make sure that the electrical information on

the rating plate agrees with the power

supply. If not, contact an electrician.

• Make sure the appliance is installed

correctly. Loose and incorrect electricity

mains cable or plug (if applicable) can make

the terminal become too hot.

• Use the correct electricity mains cable.

• Do not let the electricity mains cable tangle.

• Make sure that a shock protection is

installed.

• Use the strain relief clamp on the cable.

• Make sure the mains cable or plug (if

applicable) does not touch the hot appliance

or hot cookware, when you connect the

appliance to the near sockets

• Do not use multi-plug adapters and

extension cables.

• Make sure not to cause damage to the

mains plug (if applicable) or to the mains

cable. Contact our Authorised Service

Centre or an electrician to change a

damaged mains cable.

• The shock protection of live and insulated

parts must be fastened in such a way that it

cannot be removed without tools.

• Connect the mains plug to the mains socket

only at the end of the installation. Make sure

that there is access to the mains plug after

the installation.

• If the mains socket is loose, do not connect

the mains plug.

• Do not pull the mains cable to disconnect

the appliance. Always pull the mains plug.

• Use only correct isolation devices: line

protecting cut-outs, fuses (screw type fuses

removed from the holder), earth leakage trips

and contactors.

• The electrical installation must have an

isolation device which lets you disconnect

the appliance from the mains at all poles.

The isolation device must have a contact

opening width of minimum 3 mm.

Gas connection

• All gas connections should be made by a

qualified person.

• Before installation, make sure that the local

distribution conditions (nature of the gas and

gas pressure) and the adjustment of the

appliance are compatible.

• Make sure that there is air circulation around

the appliance.

• The information about the gas supply is on

the rating plate.

• This appliance is not connected to a device,

which evacuates the products of

combustion. Make sure to connect the

appliance according to current installation

regulations. Pay attention to requirements

regarding adequate ventilation.

Use

WARNING!

Risk of injury, burns and electrical

shock.

• Remove all the packaging, labelling and

protective film (if applicable) before first use.

• Use this appliance in a household

environment.

• Do not change the specification of this

appliance.

• Make sure that the ventilation openings are

not blocked.

• Do not let the appliance stay unattended

during operation.

• Set the cooking zone to “off” after each use.

• Do not put cutlery or saucepan lids on the

cooking zones. They can become hot.

• Do not operate the appliance with wet hands

or when it has contact with water.

• Do not use the appliance as a work surface

or as a storage surface.

• When you place food into hot oil, it may

splash.

WARNING!

Risk of fire and explosion

• Fats and oil when heated can release

flammable vapours. Keep flames or heated

objects away from fats and oils when you

cook with them.

• The vapours that very hot oil releases can

cause spontaneous combustion.

• Used oil, that can contain food remnants,

can cause fire at a lower temperature than

oil used for the first time.

• Do not put flammable products or items that

are wet with flammable products in, near or

on the appliance.

WARNING!

Risk of damage to the appliance.

• Do not keep hot cookware on the control

panel.

18 www.zanussi.com

• Do not let cookware to boil dry.

• Be careful not to let objects or cookware fall

on the appliance. The surface can be

damaged.

• Do not activate the cooking zones with

empty cookware or without cookware.

• Do not put aluminium foil on the appliance.

• Use only stable cookware with the correct

shape and diameter larger than the

dimensions of the burners.

• Make sure cookware is centrally positioned

on the burners.

• Make sure the flame does not go out when

you quickly turn the knob from the maximum

to the minimum position.

• Use only the accessories supplied with the

appliance.

• Do not install a flame diffuser on the burner.

• The use of a gas cooking appliance results

in the production of heat and moisture.

Provide good ventilation in the room where

the appliance is installed.

• Prolonged intensive use of the appliance

may call for additional ventilation, for

example opening of a window, or more

effective ventilation, for example increasing

the level of mechanical ventilation where

present.

• This appliance is for cooking purposes only.

It must not be used for other purposes, for

example room heating.

• Do not let acid liquids, for example vinegar,

lemon juice or limescale remover, touch the

hob. This can cause matt patches.

Care and cleaning

• Clean regularly the appliance to prevent the

deterioration of the surface material.

• Deactivate the appliance and let it cool

down before you clean it.

• Disconnect the appliance from the electrical

supply before maintenance.

• Do not use water spray and steam to clean

the appliance.

• Clean the appliance with a moist soft cloth.

Only use neutral detergents. Do not use

abrasive products, abrasive cleaning pads,

solvents or metal objects.

• Do not clean the burners in the dishwasher.

Disposal

WARNING!

Risk of injury or suffocation.

• Contact your municipal authority for

information on how to discard the appliance

correctly.

• Disconnect the appliance from the mains

supply.

• Cut off the mains cable and discard it.

• Flat the external gas pipes.

Service

• To repair the appliance contact an

Authorised Service Centre.

• Use original spare parts only.

Product description

Cooking surface layout

3

4

5

2

1

Semi-rapid burner

2

Triple Crown burner

3

Rapid burner

4

Auxiliary burner

5

Control knobs

www.zanussi.com 19

Control knob

Symbol Description

no gas supply / off position

Symbol Description

ignition position / maximum

gas supply

minimum gas supply

Daily use

WARNING!

Refer to Safety chapters.

Burner overview

A

B

D

C

D

A

B

A. Burner cap

B. Burner crown

C. Ignition candle

D. Thermocouple

Ignition of the burner

Always light the burner before you

put on the cookware.

WARNING!

Be very careful when you use open

fire in the kitchen environment. The

manufacturer declines any

responsibility in case of the flame

misuse.

1. Push the control knob down and turn it

counterclockwise to the maximum gas

supply position ( ).

2. Keep the control knob pushed for equal or

less than 10 seconds. This lets the

thermocouple warm up. If not, the gas

supply is interrupted.

3. Adjust the flame after it is regular.

If after some tries the burner does

not light, check if the crown and its

cap are in correct positions.

WARNING!

Do not keep the control knob

pushed for more than 15 seconds. If

the burner does not light after 15

seconds, release the control knob,

turn it into off position and try to light

the burner again after minimum 1

minute.

20 www.zanussi.com

CAUTION!

In the absence of electricity you can

ignite the burner without electrical

device; in this case approach the

burner with a flame, turn the control

knob counter-clockwise to maximum

gas supply position and push it

down. Keep the control knob

pushed for equal or less than 10

seconds to let the thermocouple

warm up.

If the burner accidentally goes out,

turn the control knob to the off

position and try to light the burner

again after minimum 1 minute.

The spark generator can start

automatically when you switch on

the mains, after installation or a

power cut. It is normal.

Turning the burner off

To put the flame out, turn the knob to the off

position .

WARNING!

Always turn the flame down or

switch it off before you remove the

pans from the burner.

Hints and tips

WARNING!

Refer to Safety chapters.

Cookware

CAUTION!

Do not use cast iron pans,

potstones, earthenware, grill or

toaster plates. The stainless steel

can become tarnished if it is too

much heated.

WARNING!

Do not put the same pan on two

burners.

WARNING!

Do not put unstable or damaged

pots on the burner to prevent from

spill and injury.

CAUTION!

Make sure that the bottoms of pots

do not stand above the control knob,

otherwise the flame heats the

control knob up.

CAUTION!

Make sure that pot handles are not

above the front edge of the cooktop.

CAUTION!

Make sure that the pots are placed

centrally on the burner in order to

get maximum stability and to get

lower gas consumption.

Diameters of cookware

Use cookware with diameters

applicable to the size of burners.

Burner Diameter of

cookware

(mm)

Triple Crown 180 - 260

Rapid 180 - 260

Semi-rapid (front) 120 - 180

Semi-rapid (rear) 120 - 220

Auxiliary 80 - 160

Care and cleaning

WARNING!

Refer to Safety chapters.

General information

• Clean the hob after each use.

www.zanussi.com 21

• Always use cookware with clean bottom.

• Scratches or dark stains on the surface have

no effect on how the hob operates.

• Use a special cleaner applicable for the

surface of the hob.

• Wash stainless steel parts with water, and

then dry them with a soft cloth.

Pan supports

The pan supports are not resistant

to washing in a dishwasher. They

must be washed by hand.

1. Remove the pan supports to easily clean

the hob.

Be very careful when you

replace the pan supports to

prevent the hob top from

damage.

2. The enamel coating occasionally can have

rough edges, so be careful when you wash

the pan supports by hand and dry them. If

necessary, remove stubborn stains with a

paste cleaner.

3. After you clean the pan supports, make sure

that they are in correct positions.

4. For the burner to operate correctly, make

sure that the arms of the pan supports are

aligned with the centre of the burner.

Cleaning the hob

• Remove immediately: melted plastic,

plastic foil, and food with sugar. If not, the

dirt can cause damage to the hob.

• Remove when the hob is sufficiently

cool: limescale rings, water rings, fat stains,

shiny metallic discoloration. Clean the hob

with a moist cloth and some detergent. After

cleaning, rub the hob dry with a soft cloth.

• To clean the enamelled parts, cap and

crown, wash them with warm soapy water

and dry them carefully before you put them

back.

Cleaning the spark plug

This feature is obtained through a ceramic

ignition candle with a metal electrode. Keep

these components well clean to prevent difficult

lighting and check that the burner crown holes

are not obstructed.

Periodic maintenance

Speak to your local Authorised Service Centre

periodically to check the conditions of the gas

supply pipe and the pressure adjuster, if fitted.

Troubleshooting

WARNING!

Refer to Safety chapters.

What to do if...

Problem Possible cause Remedy

There is no spark when you try to

activate the spark generator.

The hob is not connected to an

electrical supply or it is connec-

ted incorrectly.

Check if the hob is correctly con-

nected to the electrical supply.

22 www.zanussi.com

Problem Possible cause Remedy

The fuse is released. Make sure that the fuse is the

cause of the malfunction. If the

fuse releases again and again,

contact a qualified electrician.

Burner cap and crown are placed

incorrectly.

Place the burner cap and crown

correctly.

The flame extinguishes immedi-

ately after ignition.

Thermocouple is not heated up

sufficiently.

After lightning the flame, keep the

knob pushed for equal or less

than 10 seconds.

The flame ring is uneven. Burner crown is blocked with

food residues.

Make sure that the injector is not

blocked and the burner crown is

clean.

If you cannot find a solution...

If you cannot find a solution to the problem

yourself, contact your dealer or an Authorised

Service Centre. Give the data from the rating

plate. Make sure, you operated the hob

correctly. If not the servicing by a service

technician or dealer will not be free of charge,

also during the warranty period. The instructions

about the Service Centre and conditions of

guarantee are in the guarantee booklet.

Labels supplied with the accessories

bag

Stick the adhesive labels as indicated below:

MOD.

PROD.NO.

SER.NO

DATA

MOD.

PROD.NO.

SER.NO

DATA

MOD.

PROD.NO.

SER.NO.

03 IT

MADE IN ITALY

TYPE

IP20

0049

A B C

A. Stick it on Guarantee Card and send this

part (if applicable).

B. Stick it on Guarantee Card and keep this

part (if applicable).

C. Stick it on instruction booklet.

www.zanussi.com 23

Installation

WARNING!

Refer to Safety chapters.

Before the installation

Before you install the hob, write down the

information bellow from the rating plate. The

rating plate is on the bottom of the hob.

Model .......................................

PNC .........................................

Serial number ...........................

Gas Connection

WARNING!

The following instructions about

installation, connection and

maintenance must be carried out by

qualified personnel in compliance

with standards and local regulations

in force.

It is necessary that the connection to the gas

mains are carried out by means of an AGB tap.

Choose fixed connections or use a flexible pipe

in AGB (stainless steel) in compliance with the

regulation in force (NBN D 51.003). If you use

flexible metallic pipes, be careful they do not

come in touch with mobile parts or they are not

squeezed. Also be careful when the hob is put

together with an oven.

Make sure that the gas supply

pressure of the appliance obeys the

recommended values. The

adjustable connection is fixed to the

comprehensive ramp by means of a

threaded nut G 1/2". All the

components shown in the figure

have already been assembled in the

factory. The appliance, before

leaving the factory, has been tested

in order to give you the best results.

A B C

A. End of shaft with nut

B. Washer

C. Elbow (if needed)

Liquid gas

Use the rubber pipe holder for liquid gas.

Always engage the gasket. Then continue with

the gas connection.

The flexible pipe is prepared for apply when:

• it can not get hot more than room

temperature, higher than 30°C;

• it is no longer than 1500 mm;

• it shows no throttles;

• it is not subject to traction or torsion;

• it does not get in touch with cutting edges or

corners;

• it can be easily examined in order to make

sure its condition.

The control of preservation of the flexible pipe

consists in checking that:

• it does not show cracks, cuts, marks of

burnings on the two ends and on its full

length;

• the material is not hardened, but shows its

correct elasticity;

• the fastening clamps are not rusted;

• expired term is not due.

If one or more defects are visible, do not repair

the pipe, but replace it.

WARNING!

When installation is complete, make

sure that the seal of each pipe fitting

is correct. Use a soapy solution, not

a flame!

Injectors replacement (only for

Belgium)

1. Remove the pan supports.

2. Remove the caps and crowns of the burner.

3. With a socket spanner 7 remove the

injectors and replace them with the ones

which are necessary for the type of gas you

use (see table in "Technical Information"

chapter).

4. Assemble the parts, follow the same

procedure backwards.

5. Replace the rating plate (it is near the gas

supply pipe) with the one for the new type

of gas supply. You can find this plate in the

package supplied with the appliance.

24 www.zanussi.com

If the supply gas pressure is changeable or

different from the necessary pressure, you must

fit an applicable pressure adjuster on the gas

supply pipe.

Adjustment of minimum level (only for

Belgium)

To adjust the minimum level of the burners:

1. Light the burner.

2. Turn the knob on the minimum position.

3. Remove the knob.

4. With a thin screwdriver, adjust the bypass

screw position (A).

A

5. If you change:

• from natural gas G20/G25 20/25 mbar

to liquid gas, fully tighten the bypass

screw in.

• from liquid gas to natural gas G20/G25

20/25 mbar, undo the bypass screw

approximately 1/4 of a turn (1/2 of a turn

for Triple Crown burner).

WARNING!

Make sure the flame does not go out

when you quickly turn the knob from

the maximum position to the

minimum position.

Electrical connection

• Make sure that the rated voltage and type of

power on the rating plate agree with the

voltage and the power of the local power

supply.

• This appliance is supplied with a mains

cable. It has to be supplied with a correct

plug which can hold the load that the rating

plate rates. Make sure that you install the

plug in a correct socket.

• Always use a correctly installed shockproof

socket.

• Make sure that there is an access to the

mains plug after the installation.

• Do not pull the mains cable to disconnect

the appliance. Always pull the mains plug.

• There is a risk of fire when the appliance is in

connection with an extension cable, an

adapter or a multiple connection. Make sure

that the ground connection agrees with the

standards and regulations.

• Do not let the power cable to heat up to a

temperature higher than 90° C.

Make sure that you connect the blue

neutral cable to the terminal with a

letter "N" on it. Connect the brown

(or black) phase cable to the

terminal which has a letter "L". Keep

the phase cable connected at all

times.

Connection cable

To replace the connection cable use only the

special cable or its equivalent. The cable type

is: H05V2V2-F T90.

Make sure that the cable section is applicable

to the voltage and the working temperature. The

yellow / green earth wire must be approximately

2 cm longer than the brown (or black) phase

wire.

Building In

min.

55 mm

min.

650 mm

560 mm

480 mm

min.

450 mm

30 mm

10 mm

86 mm

A

3 mm

www.zanussi.com 25

A

B

A. supplied seal

B. supplied brackets

CAUTION!

Install the appliance only on a

worktop with flat surface.

Possibilities for insertion

The panel installed below the hob must be easy

to remove and let an easy access in case a

technical assistance intervention is necessary.

Kitchen unit with door

min 20 mm

(max 150 mm)

30 mm

60 mm

B

A

A. Removable panel

B. Space for connections

Kitchen unit with oven

The electrical connection of the hob and the

oven must be installed separately for safety

reasons and to let easy remove oven from the

unit.

Technical information

Hob dimensions

Width 744 mm

Depth 510 mm

Other technical data

TOTAL POWER:

Gas original:

G20/G25 (2E+) 20/25 mbar (BE) = 12 kW

G20 (2E) 20 mbar (LU) = 12 kW

Gas replacement: G30 (3+) 28-30 mbar = 858 g/h

G31 (3+) 37 mbar = 843 g/h

Electric supply: 230 V ~ 50 Hz

Appliance category: II2E+3+ (BE)

I2E (LU)

Gas connection: R 1/2"

Appliance class: 3

Bypass diameters

BURNER Ø BYPASS 1/100 mm

Triple Crown 56

26 www.zanussi.com

BURNER Ø BYPASS 1/100 mm

Rapid 42

Semi-rapid 32

Auxiliary 28

Gas burners for NATURAL GAS G20/G25 20/25 mbar (BE) - G20 20 mbar (LU)

BURNER NORMAL POWER kW MINIMUM POWER kW INJECTOR MARK

1/100 mm

Triple Crown 4,0 1,4 146

Rapid 3,0 0,75 119

Semi-rapid 2,0 0,45 96

Auxiliary 1,0 0,33 70

Gas burners for LPG G30/G31 28-30/37 mbar

BURNER NORMAL

POWER

kW

MINIMUM

POWER

kW

INJECTOR

MARK 1/100

mm

NOMINAL GAS FLOW g/h

G30 28-30

mbar

G31 37 mbar

Triple Crown 4,0 1,4 98 291 286

Rapid 2,8 0,75 86 204 200

Semi-rapid 2,0 0,45 71 145 143

Auxiliary 1,0 0,33 50 73 71

Energy efficiency

Product information according to EU 66/2014

Model identification ZGG75524SA,

ZGG75524XA

Type of hob Built-in hob

Number of gas burners 5

www.zanussi.com 27

Energy efficiency per gas burner

(EE gas burner)

Centre middle - Triple Crown 52.0%

Left rear - Semi-rapid 53.9%

Right rear - Rapid 52.7%

Left front - Semi-rapid 53.9%

Right front - Auxiliary not applicable

Energy efficiency for the gas hob

(EE gas hob)

53.1%

Model identification ZGG76524XA

Type of hob Built-in hob

Number of gas burners 5

Energy efficiency per gas burner

(EE gas burner)

Centre middle - Triple Crown 52.0%

Left rear - Semi-rapid 54.7%

Right rear - Rapid 56.3%

Left front - Semi-rapid 54.7%

Right front - Auxiliary not applicable

Energy efficiency for the gas hob

(EE gas hob)

54.4%

EN 30-2-1: Domestic cooking appliances burning gas - Part 2-1 : Rational use of energy - General

Energy saving

• Before use, make sure that the burners and pan supports are assembled correctly.

• Use cookware with diameters applicable to the size of burners.

• Center the pot on the burner.

• When you heat up water, use only the amount you need.

• If it is possible, always put the lids on the cookware.

• When the liquid starts to boil, turn down the flame to barely simmer the liquid.

• If it is possible, use a pressure cooker. Refer to its user manual.

ENVIRONMENTAL CONCERNS

Recycle the materials with the symbol . Put

the packaging in applicable containers to

recycle it. Help protect the environment and

human health and to recycle waste of electrical

and electronic appliances. Do not dispose

appliances marked with the symbol with the

household waste. Return the product to your

local recycling facility or contact your municipal

office.

28 www.zanussi.com

Page is loading ...

www.zanussi.com/shop

867315062-B-452015

Zanussi ZGG75524XA User manual

This manual is also suitable for

Zanussi ZGG75524XA User manual

in other languages