Electrolux EDC67550W User manual

Category
Tumble dryers
Type
User manual
user manual
用户手册
Tumble Dryer
滚筒干衣机
EDC67550W
Electrolux. Thinking of you.
Share more of our thinking at www.electrolux.com
Contents
Important safety information 2
Environment 4
Product description 5
Control panel 6
Before first use 6
Programme chart 6
Sorting and preparing laundry 7
Daily use 8
Cleaning and maintenance 10
What to do if ... 12
Technical data 14
Machine settings 14
Hints for test institutes 15
Installation 15
Service 17
Subject to change without notice
Important safety information
Important! In the interest of your safety
and to ensure the correct use, before
installing and first using the appliance,
read this user manual carefully,
including its hints and warnings. To
avoid unnecessary mistakes and
accidents, it is important to ensure that
all people using the appliance are
thoroughly familiar with its operation
and safety features. Save these
instructions and make sure that they
remain with the appliance if it is moved
or sold, so that everyone using it through
its life will be properly informed on
appliance use and safety.
General safety
It is dangerous to alter the specifications or
attempt to modify this product in any way.
This appliance is not intended for use by
persons (including children) with reduced
physical, sensory or lack of experience and
knowledge, unless they have been given
supervision or instruction concerning use
of the appliance by a person responsible
for their safety.
Make sure that small pets do not climb into
the drum. To avoid this, please check into
the drum before using.
Any objects such as coins, safety pins,
nails, screws, stones or any other hard,
sharp material can cause extensive dam-
age and must not be placed into the ma-
chine.
In order to avoid danger of fires caused by
excessive drying, do not use appliance to
dry the following items: Cushions, quilts
and the like (these items accumulate heat).
Items such as foam rubber (latex foam),
shower caps, waterproof textiles, rubber
backed articles and clothes or pillows fit-
ted with foam rubber pads should not be
dried in the tumble dryer.
Always unplug the appliance after use,
clean and maintenance.
Under no circumstances should you at-
tempt to repair the machine yourself. Re-
pairs carried out by inexperienced persons
may cause injury or serious malfunction-
ing. Contact your local Service Centre. Al-
ways insist on genuine spare parts.
Items that have been soiled with substan-
ces such as cooking oil acetone, petrol,
kerosene, spot removers, turpentine, wax-
es and wax removers should be washed in
hot water with an extra amount of deter-
gent before being dried in the tumble dry-
er.
Danger of explosion: Never tumble dry
items that have been in contact with in-
flammable solvents (petrol, methylated
spirits, dry cleaning fluid and the like). As
these substance are volatile, they could
cause an explosion. Only tumble dry items
washed with water.
Risk of fire: items that have been spotted
or soaked with vegetable or cooking oil
constitute a fire hazard and should not be
placed in the tumble dryer.
If you have washed your laundry with stain
remover you must execute an extra rinse
cycle before loading your tumble dryer.
2 electrolux
Please make sure that no gas lighters or
matches have accidentally been left in
pockets of garments to be loaded into ap-
pliance
Warning! Never stop a tumble dry
before the end of the drying cycle
unless all items are quickly removed
and spread out so that the heat is
dissipated. Risk of fire!
Risk of electric shock! Do not spray
down the appliance with jets of water.
Installation
This appliance is heavy. Care should be
taken when moving it.
When unpacking the appliance, check that
it is not damaged. If in doubt, do not use it
and contact the Service Centre.
All packaging must be removed before
use. Serious damage can occur to the
product and to property if this is not ad-
hered to. See relevant section in the user
manual.
The final part of a tumble dryer cycle oc-
curs without heat ( cool down cycle ) to
ensure that the items are left at a temper-
ature that ensures that items will not be
damaged.
Any electrical work required to install this
appliance should be carried out by a quali-
fied electrician or competent person.
Care must be taken to ensure that the ap-
pliance does not stand on the electrical
supply cable.
If the machine is situated on a carpeted
floor, please adjust the feet in order to al-
low air to circulate freely under the appli-
ance.
After having installed the appliance, check
that it is not pressing or standing on its
electrical supply cable.
If the tumble dryer is placed on top of a
washing machine, it is compulsory to use
the stacking kit (optional accessory).
Use
This appliance is designed for domestic
use. It must not be used for purposes other
than those for which it was designed.
Only dry fabrics which are designed to be
machine dried. Follow the instructions on
each garment label.
Do not dry unwashed items in the tumble
dryer.
Do not overload the appliance. See the
relevant section in the user manual.
Clothes which are dripping wet should not
be placed in the dryer.
Garments which have been in contact with
volatile petroleum products should not be
machine dried. If volatile cleaning fluids are
used, care should be taken to ensure that
the fluid is removed from the garment be-
fore placing in the machine.
Never pull the power supply cable to re-
move the plug from the socket; always
take hold of the plug itself.
Never use the tumble dryer if the power
supply cable, the control panel, the work-
ing surface or the base are damaged so
that the inside of the tumble dryer is ac-
cessible.
Fabric softeners, or similar products
should be used as specified by the fabric
softener instructions.
Caution - hot surface : Do not touch the
door light cover surface when the light is
switched on (only dryers equipped with in-
ternal drum light).
Child safety
This machine is not intended for use by
young children or infirm persons without
supervision.
Children should be supervised to ensure
that they do not play with the appliance.
The packaging components (e.g. plastic
film, polystyrene) can be dangerous to chil-
dren - danger of suffocation! Keep them
out of children’s reach.
Keep all detergents in a safe place out of
children’s reach.
Make sure that children or pets do not
climb into the drum.
electrolux 3
Environment
The symbol on the product or on its
packaging indicates that this product may
not be treated as household waste. Instead
it should be taken to the appropriate
collection point for the recycling of electrical
and electronic equipment. By ensuring this
product is disposed of correctly, you will help
prevent potential negative consequences for
the environment and human health, which
could otherwise be caused by inappropriate
waste handling of this product. For more
detailed information about recycling of this
product, please contact your local council,
your household waste disposal service or the
shop where you purchased the product.
Old appliance
Warning!
Remove mains plug from socket when you
have no further use for the machine. Cut off
mains cable and dispose of together with
plug. Destroy loading door hook. Children
cannot then lock themselves in the machine
and put their lives at risk.
Packaging material
The packaging materials are environmentally
friendly and can be recycled. The plastic
components are identified by markings, e.g.
>PE<, >PS<, etc. Please dispose of the
packaging materials in the appropriate con-
tainer at the community waste disposal fa-
cilities.
Environmental tips
In the dryer, laundry becomes fluffy and
soft. Fabric softeners are not therefore
needed when washing.
Your dryer will function most economically
if you:
always keep the ventilation slots on the
base of the dryer unobstructed;
use the loading volumes specified in the
programme overview;
ensure you have good ventilation in the
installation room;
clean the micro-fine filter and fine strain-
er after each drying cycle;
spin the laundry well before drying.
Energy consumption depends on spin-
ning speed set in washing machine.
Higher spinning speed - lower energy
consumption.
4 electrolux
Product description
1
3
4
2
5
6
7
8
9
10
1 Control panel
2 Fluff filters
3 Loading door (reversible)
4 Ventilation grille
5 Adjustable feet
6 Drawer with condensed water container
7 Push button for base door opening
8 Rating Plate
9 Heat exchanger
10 Heat exchanger door
electrolux 5
Control panel
1 2 4
3
5
1 Programme knob and On/Off switch
2 DELAY TIMER button
3 START/PAUSE button
4 Indicator lights
5 Function buttons
Before first use
In order to remove any residues which may
have been produced during production, wipe
the dryer drum with a damp cloth or carry out
a brief drying cycle (30 MIN) with damp clo ths
in the machine.
1.
Turn the programme knob to
TIME
(TIME) .
2. Press the START/PAUSE (START/
PAUSE) button.
Programme chart
Programme
max. load
(dry clothes)
Application/properties
Care label
Cottons
Extra (Extra)
7 kg
Thorough drying of thick or multi- layered fabrics, e.g. terry
towelling items, bathrobes.
Strong
(Strong)
7 kg Drying thick textiles, e.g. terry towelling items, towels.
Cupboard
(Cupboard)
7 kg
Thorough drying of fabrics of even thicknesses, e.g. terry
towelling items, knitwear, towels.
Damp (Damp)
7 kg
For thin textiles which are still to be ironed, e.g. knitted items,
cotton shirts.
Iron (Iron)
7 kg
For thin fabrics which are also to be ironed, e.g. knitwear,
cotton shirts.
Synthetics
Extra (Extra)
3 kg
Thorough drying of thick or multi-layered fabrics, e.g. pull-
overs, bedding, table linen.
6 electrolux
Programme
max. load
(dry clothes)
Application/properties
Care label
Cupboard
(Cupboard)
3 kg
For thin fabrics which are not ironed, e.g. easy care shirts,
table linen, baby clothes, socks, lingerie with bones or wires.
Iron (Iron)
3 kg
For thin fabrics which are also to be ironed, e.g. knitwear,
cotton shirts.
Special
Time 30' 60'
1 kg
Drying thick or multi-layered textiles, e.g. terry towelling
items. For drying individual items of laundry or for small vol-
umes of less than 1kg.
Mix (Mix)
3 kg
For drying cotton and synthetic fabrics, uses low tempera-
ture.
Easy (Easy)
1 kg
(or 5
shirt
s)
Special program with anti-crease mechanism for easy care
fabrics such shirts and blouses; for minimum ironing effort.
The results depends on the type of fabric and its finish. Place
fabrics in the dryer straight after spinning; once dried, imme-
diately remove fabrics and place on a clothes hanger.
Jeans (Jeans)
7 kg
For leisure clothing, such as jeans, sweat-shirts, etc., of dif-
ferent material thicknesses (e.g. at the neck, cuffs and
seams).
Cooling
(Cooling)
1 kg
Special programme, lasting around 10 minutes, for refreshing
or gently cleaning textiles with commercially available dry
cleaning sets. (Only use those products which are declared
as suitable for the drier by the manufacturer; please observe
the manufacturer’s instructions for use.)(Buzzer (Buzzer)
function available)
Sorting and preparing laundry
Sorting laundry
Sort by fabric type:
Cotton/linen for programmes in COT-
TONS (COTTONS ) programme group.
Mixed fibres and synthetics for pro-
grammes in the SYNTHETICS (SYN-
THETICS) programme group.
Sorting by care label. The care labels
mean:
Drying in the tumble dryer possible in prin-
ciple
Dry at normal temperature
Dry at reduced temperature (press DELI-
CATE (DELICATE) button!)
Drying in the tumble dryer not possible
Important! Do not place in the appliance any
wet laundry which is not specified on the care
label as being suitable for tumble-drying.
This appliance can be used for all wet laundry
items which are labelled as suitable for tum-
ble-drying.
Do not dry new, coloured textiles together
with light-coloured laundry items. Textile
colours may bleed.
Do not dry cotton jersey and knitwear with
the EXTRA (EXTRA) programme. Items
may shrink!
Preparing laundry
To avoid laundry becoming tangled: close
zips, button up duvet covers and tie loose
ties or ribbons (e.g. of aprons).
Empty pockets. Remove metal items (pa-
per clips, safety pins, etc).
electrolux 7
Turn items with double-layered fabrics in-
side out (e.g. with cotton-lined anoraks,
the cotton layer should be outermost).
These fabrics will then dry better.
Important! Do not overload the appliance.
Observe max. loading volume of 7 kg.
Laundry weights
Type of laun-
dry
Weight
Bathrobe 1200 g
Napkin 100 g
Quilt cover 700 g
Sheet 500 g
Pillow case 200 g
Tablecloth 250 g
Type of laun-
dry
Weight
Towelling tow-
el
200 g
Tea cloth 100 g
Night dress 200 g
Ladies' briefs 100 g
Man's work
shirt
600 g
Man's work
shirt
200 g
Man's pyja-
mas
500 g
Blouse 100 g
Men's under-
pants
100 g
Daily use
Switching machine on
Turn the programme selector to any pro-
gramme. The machine switches on. When
the loading door is open, the internal lamp
illuminates the drum.
Door opening and laundry loading
1. Open loading door:
Push against the loading door (push
point)
2. Load your laundry (do not force it in).
Caution! Do not jam laundry in between
the loading door and rubber seal.
3. Close loading door securely. Lock must
audibly lock.
Selecting the programme
Turn the programme selector dial to the re-
quired programme. The light Start/
Pause(Start/Pause) starts to flash.
Selecting additional functions
You can choose from the additional functions
1
Delicate (Delicate),
2
Dryness (Dryness),
3
Buzer (Buzer ) and
4
Delay (Delay).
8 electrolux
1 2 3 4
Delicate (Delicate)
For especially gentle drying of sensitive fab-
rics with the care label and for temperature-
sensitive textiles (e.g. acrylic, viscose). Pro-
gramme is executed with reduced heat. Del-
icate (Delicate) is only suitable for use with
loads of up to 3kg.
1. Press the Delicate (Delicate) button. The
corresponding pilot light comes on.
Dryness (Dryness)
Press the Dryness (Dryness) button repeat-
edly, to select the desired option. The rele-
vant light will light up. Laundry becomes dry-
er from MIN to MAX. Press the Dryness (Dry-
ness) button as many times as necessary
until the small light at the level of residual
dampness required is illuminated.
When the programme has finished the pilot
lights End is on.
Buzzer (Buzzer)
When the drying cycle has finished, an inter-
mittent audible signal will sound.
By depressing button Buzzer (Buzzer) the
acoustic signal is switched off in the following
cases:
when selecting the programme
when depressing the buttons
when the programme selector dial is
turned to another position during the pro-
gramme or when you depress an option
button during the cycle
at the end of the programme.
The corresponding light comes on
Delay (Delay)
This button allows you to delay the starting
of the programme by 3, 6 or 9 hours.
Press the button until the light relevant to the
desired delay lights up. This option must be
selected after having selected the pro-
gramme and before 3 6 9 pressing START/
PAUSE (START/PAUSE) to start the pro-
gramme.
The machine begins the countdown, which
is shown by the pilot lights. For example, if
you have chosen a 9-hour delay (pilot light 9h
lit), after 3 hours, 9h goes out and 6h lights
up; after 3 more hours, 6h goes out and 3h
lights up. When the 9 hours are over (pilot
light 3h off), the drying cycle begins.During
the delayed start period, it is not possible to
change the programme or the selected de-
lay. If you wish to do so, you must first cancel
everything by rotating the programme selec-
tor dial to position “O”. Select the new pro-
gramme, the options and the delayed start,
then press START/PAUSE (START/PAUSE) .
If you wish to change only the options, this
can be done on condition that the new op-
tion(s) is(are) compatible with the pro-
gramme. Set the machine to PAUSE by de-
pressing the relevant button, select the new
option(s) and depress START/PAUSE
(START/PAUSE) button again.
If you wish to add some laundry while the
machine is performing the countdown, after
having done so and having closed the door,
press START/PAUSE (START/PAUSE)
again, in order to allow the machine to com-
plete the remaining countdown time.
Starting the programme
Press the START/PAUSE (START/PAUSE)
button. The relevant light will stop flash-
ing .The Programme is started. The indicator
lights of DRYING (DRYING) and COOLING
(COOLING) light up one after the other. All
drying programmes end with a 10 minute
cooling phase (light COOLING (COOLING) is
on). You may remove the laundry after this
phase.
Changing programme
To change a programme which is running,
first cancel it by turning the programme se-
lector dial to “ O ”. Select the new pro-
gramme and press the START/PAUSE
(START/PAUSE) button .
electrolux 9
Putting in extra items or taking items out
before end of programme
1. Open loading door.
Warning! Laundry and drum can
become hot. Risk of burns!
2. Load or remove laundry items.
3. Close loading securely. Lock must audi-
bly lock.
4. Press the START/PAUSE (START/
PAUSE) button to continue the drying cy-
cle.
Drying cycle complete / removing
laundry
Once the drying cycle is complete, The lights
ANTICREASE/END (ANTICREASE/END),
filter and full tank illuminate. If the Buz-
zer (Buzzer) button has been pressed, an
acoustic signal sounds intermittently for
about one minute.
The drying cycles (except from the
WOOL (WOOL) programme) are auto-
matically followed by an anti-crease
phase which lasts around 30 minutes.
The drum rotates at intervals during this
phase. This keeps the laundry loose and
free of creases. The laundry can be re-
moved at any time during the anti-
crease phase. (The laundry should be
taken out towards the end of the anti-
crease phase at the latest to prevent
creases from forming.)
1. Open door.
2. Before removing the laundry, remove fluff
from the micro-fine filter. It is best to use
a damp hand for this purpose. (See
“Maintenance and cleaning” chapter.)
3. Remove laundry.
4.
Turn the programme selector to
off .
Important! After each drying cycle:
- Clean the micro-fine filter and fine filter
- Drain the condensed water container
(See chapter “Maintenance and clean-
ing ”.)
5. Close the door.
Cleaning and maintenance
Cleaning lint filters
To ensure that the appliance works perfectly,
the lint filters in the door and in front of the
drum must be cleaned after every drying cy-
cle.
Caution! Important. Never operate the
dryer without the lint filter or with a
damaged or blocked lint filter.
1. Open loading door
2. Use a damp hand to clean the micro- fine
filter, which is built into the lower part of
the loading aperture.
3. After a period of time, a patina due to de-
tergent residue on laundry forms on the
filters. When this occurs, clean the filters
with warm water using a brush. Remove
the filter from the door pulling it out. It can
be positioned with the tooth facing to the
left or to the right). After cleaning do not
forget to put it back.
4. Remove fluff from lint filter, preferably us-
ing a damp hand for this purpose.
5. Replace the filter.
10 electrolux
Clean the door seal
Wipe the door seal with a damp cloth imme-
diately after the drying cycle has finished.
Emptying the water reservoir
Empty the water reservoir after every drying
cycle.
If the water reservoir is full, an active pro-
gramme will break off automatically and the
empty container
icon on the display will
light up. In order to continue the programme,
the water reservoir must first be emptied.
Warning! The condensed water is not
suitable for drinking or for preparing
foodstuffs.
1. Take out water reservoir completely.
2. Pour condensed water out into a basin or
similar receptacle.
3. Refit water reservoir.
If the programme has been interrupted as
a result of the water reservoir being full:
Press the START/PAUSE button to con-
tinue the drying cycle.
The water reservoir has a volume of ap-
prox. 4 litres. This is sufficient for around
7 kg of laundry which has previously
been spun at 1000 revolutions/ minute.
The condensate can be used as distilled
water, e.g. for steam ironing. However
first filter the condensate (e.g. with a cof-
fee filter) to remove any residue and
small pieces of fluff.
Cleaning heat exchanger
If the
HEAT EXCHANGER is displayed,
the heat exchanger needs to be cleaned.
Caution! Operating when the heat
exchanger is blocked with fluff can
damage the dryer. This also increases
energy consumption.
1. Open door.
2. Open door in plinth. To do this, press the
release button on the bottom of the door
aperture and open the door in the plinth
to the left.
electrolux 11
3. Clean fluff from the inside of the door and
the heat exchanger front chamber. Wipe
the door seal with a damp cloth.
4. Turn both lock washers inwards.
5. Use the handle to pull the heat exchanger
out of the base and carry it horizontally to
prevent any remaining water from spilling.
6. To empty the heat exchanger, hold verti-
cally over a washing-up bowl.
Caution! Do not use sharp objects to
clean. The heat exchanger could
develop leaks.
7. Clean heat exchanger.
It is best to use a brush or to rinse thor-
oughly with a hand-held shower.
8. Replace heat exchanger and lock into
place (turn both lock washers outwards
until they snap into place).
9. Close door in plinth.
The appliance will not operate if the
HEAT EXCHANGER indicator is still lit.
Caution! Never operate the dryer
without the heat exchanger.
Cleaning the drum
Caution! Do not use abrasives or steel
wool to clean the drum.
Lime in the water or cleaning agents may
form a barely visible lining on the inside
of the drum. The degree to which the
laundry has been dried is then no longer
detected reliably. The laundry is damper
than expected when removed from the
appliance.
Use a standard domestic cleaner (e.g. vine-
gar-based cleaner) to wipe down the inside
of the drum and drum ribs.
Clean control panel and housing
Caution! Do not use furniture cleaners
or aggressive cleaning agents to clean
the machine.
Use a damp cloth to wipe down the control
panel and housing.
What to do if ...
Troubleshooting by yourself
Problem Possible cause Remedy
Dryer does not work.
Mains plug is not plugged in or fuse
is not working correctly.
Plug in at mains socket. Check fuse
in fuse box (domestic installation).
Loading door is open. Close loading door.
12 electrolux
Have you pressed the START/
PAUSE (START/PAUSE) button?
Press the START/PAUSE (START/
PAUSE) button again.
Drying results unsatisfac-
tory.
Wrong programme selected.
Select a different programme the
next time you dry (see “Programme
overview” chapter).
Lint filters clogged. Clean lint filters.
Fluff filter clogged. Clean fluff filter.
Heat exchanger clogged with lint. Clean heat exchanger.
Overloading of laundry.
Observe recommended loading
volumes.
Ventilation slots in base area cov-
ered up.
Uncover ventilation slots in base
area.
Residue on inside surface of drum
or drum ribs.
Clean inside surface of drum and
drum ribs.
Conductance of water at installa-
tion site differs from standard set-
ting of machine.
Re-programme standard setting for
degree of drying (see ‘Program-
ming options’ chapter).
When a button is pressed
- no reaction of the ma-
chine.
Drying protection. After the start of
the programme, the option can no
longer be set.
Turn the programme knob to O
off . Set the programme again.
Displayed programme
time changes erratically or
stays unchanged for a
long time.
Programme time is corrected auto-
matically depending on type and
volume of laundry and level of
dampness.
Automatic process; this is not a
machine fault.
Programme inactive,
CONTAINER display illu-
minated.
Condensate tank is full.
Empty condensate tank, then start
programme with START/PAUSE
(START/PAUSE) button.
Drying cycle ends shortly
after programme starts.
ANTICREASE (ANTI-
CREASE) light is on.
Not enough washing loaded or
washing loaded is too dry for selec-
ted programme.
Select time programme or higher
drying level (e.g.
EXTRA (EX-
TRA) instead of
CUPBOARD
(CUPBOARD).
Drying cycle lasts an un-
usually long time. Note:
After up to 5 hours the
drying cycle ends auto-
matically (see ‘End of dry-
ing cycle’).
Lint filter clogged. Clean lint filter.
Fluff filter clogged. Clean fluff filter.
Load volume too big. Reduce load volume.
Laundry insufficiently spun. Laundry must be adequately spun.
Particularly high room temperature.
Temporary switching off of the
compressor to avoid overload.
Automatic process, there is no fault
with the appliance. If possible, low-
er the room temperature.
Discoloration Colour fastness of textiles.
Check colour fastness of textiles.
Only treat textiles together if they
are a similar colour.
electrolux 13
Technical data
This appliance conforms with the following EU Directives:
2006/95/EC dated 12.12.2006 Low Voltage Directive
89/336/EEC dated 03.05.1989 EMC Directive inclusive of Amending Directive
92/31/EEC
93/68/EEC dated 22.07.1993 CE Marking Directive
Height x width x depth 85 x 60 x 58 cm
Drum volume 108 l
Depth with loading door open 109 cm
Height can be adjusted by 1.5 cm
Weight when empty approx. 40 kg
Loading volume (depends on programme)
1)
max. 7 kg
Voltage 230 V - 240 V
Required fuse 10 A
Total power 2350 W
Energy efficiency class
B
Energy consumption (7 kg of cotton, pre-
drained at 1000 rpm)
2)
3.92 kWh
Average annual energy consumption 284,1 kWh
Use Domestic
Permissible ambient temperature + 5°C to + 35°C
Consumption values
The consumption values have been established under standard conditions. They may de-
viate when the machine is operated in domestic circumstances.
Programme
Energy consumption in kWh / average
drying time in min.
COTTON CUPBOARD (COTTON CUP-
BOARD)
2)
3)
3.92 / 125 (7 kg load pre-drained at 1000
rpm)
3,6 / 119 (7 kg load pre-drained at 1400 rpm)
COTTON IRON (COTTON IRON)
2)
3.34 / 107 (7 kg load pre-drained at 1000
rpm)
SYNTHETICS CUPBOARD (SYNTHETICS
CUPBOARD)
2)
1.33 / 48 (3 kg load pre-drained at 1200 rpm)
1) Different loading volume data may be needed in some countries as a result of different measuring
methods.
2) in accordance with EN 61121
Machine settings
Setting Implementation
BUZZER (BUZZER ) perma-
nent off
1. Turn the programme selector to any programme.
2. Press simultaneously the DELICATE and DRYNESS buttons
and hold down for approx. 5 seconds.
3.
The buzzer is by default always off. You can use BUZZER button
to activate or deactivate sound but machine does not memorize
your selection.
14 electrolux
Water hardness
Water contains, a variable
quantity of limestone and min-
eral salts of which quantities
vary according to geographical
locations thus varying its con-
ductivity values.
Relevant variations of the con-
ductivity of the water compared
to those prefixed by the factory
could slightly influence the re-
sidual humidity of the laundry at
the end of the cycle. Your dryer
allows you to regulate the sen-
sitivity of the drying sensor
based on conductivity values of
the water.
1. Turn the programme selector to any programme.
2. Press simultaneously the DRYNESS and START/PAUSE but-
tons and hold down for approx. 5 seconds:
low conductivity <300 micro S/cm
medium conductivity 300-600 micro S/cm
high conductivity >600 micro S/cm
3.
Press the START/PAUSE START/PAUZE button sequentially
until you set desired level.
4. To memorize setting press simultaneously the the DRYNESS
and START/PAUSE buttons or turn knob to O off position
Hints for test institutes
Parameters possible to checked by the Test
Institutes:
Energy consumption (corrected with final
humidity) during the cupboard dry cotton
cycle with nominal load.
Energy consumption (corrected with final
humidity) during the cupboard dry cotton
cycle with half load.
Final humidity (during cupboard dry cot-
ton, iron dry cotton and cupboard dry easy
care)
Condensation efficiency (corrected with fi-
nal humidity) during cupboard dry cotton
cycle with nominal and half load
All the cycles have to be checked in accord-
ance with EN 61121 (Tumble dryers for
household use – Methods for measuring the
performance).
Installation
Important! The appliance must be moved in
vertical position for transport.
Appliance positioning
It is recommended that, for your conven-
ience, the machine is positioned close to
your washing machine.
The tumble dryer must be installed in a
clean place, where dirt does not build up.
Air must be able to circulate freely all round
the appliance. Do not obstruct the front
ventilation grille or the air intake grilles at
the back of the machine.
To keep vibration and noise to a minimum
when the dryer is in use, it should be
placed on a firm, level surface.
Once in its permanent operating position,
check that the dryer is absolutely level with
the aid of a spirit level. If it is not, raise or
lower the feet until it is.
The feet must never be removed. Do not
restrict the floor clearance through deep-
pile carpets, strips of wood or similar. This
might cause heat built-up which would in-
terfere with the operation of the appliance.
Important!
The hot air emitted by the tumble dryer can
reach temperatures of up to 60°C. The ap-
pliance must therefore not be installed on
floors which are not resistant to high temper-
atures.
When operating the tumble dryer, the room
temperature must not be lower than +5°C
and higher than +35°C, as it may affect the
performance of the appliance.
Important! Should the appliance be moved,
it must be transported vertically.
electrolux 15
Important! The appliance must not be
installed behind the lockable door, a sliding
door a door with a hinge on the opposite side
to that of the appliance.
Removing transport safety packaging
Caution!
Before use all parts of the transport packag-
ing must be removed.
1. Open loading door
2. Pull off adhesive strips from inside ma-
chine on top of drum.
3. Remove foil hose and polystyrene pad-
ding from the machine.
Electrical connection
Details on mains voltage, type of current and
the fuses required should be taken from the
rating plate. The rating plate is fitted near the
loading aperture (see “Product description”
chapter).
Connect the machine to an earthed socket,
in accordance with current wiring regula-
tions.
Warning! The manufacturer declines
any responsibility for damage or
injury through failure to comply with
the above safety precautions.
Should the appliance power supply
cable need to be replaced, this must
be carried out by an authorised serv-
ice engineer or a qualified electri-
cian. .
The appliance is supplied with a 13 amp plug
fitted. In the event of having to change the
fuse in the plug supplied, a 13 amp ASTA
approved BS 1363/A fuse must be used.
1
2
3
4
The wires in the mains lead are coloured in
accordance with the following code:
1 Blue - Neutral
2 cord clamp
3 Brown - Live
4 Green and Yellow - Earth
The wire coloured green and yellow must be
connected to the terminal marked with the
letter «E» or by the earth symbol
or col-
oured green and yellow.
The wire coloured blue must be connected
to the terminal «N» or coloured black.
The wire coloured brown must be connected
to the terminal marked «L» or coloured red.
Upon completion there must be no cut, or
stray strands of wire present and the cord
clamp must be secure over the outer sheath.
Warning! A cut off plug inserted into
a 13 amp socket is a serious safety
(shock) hazard.
Ensure that the cut off plug is dis-
posed of safely.
Warning! The plug must be
accessible after installing the
machine.
16 electrolux
Permanent connection
In the case of permanent connection it is
necessary that you install a double pole
switch between the appliance and the elec-
tricity supply (mains), with a minimum gap of
3 mm between the switch contacts and of a
type suitable for the required load in compli-
ance with the current electrical regulations.
The switch must not break the yellow and
green earth cable at any point.
Special accessories
The following special accessories are availa-
ble from your Electrolux Service Force Centre
or your specialist dealer:
Intermediate installation kits for stacked
washer and iron aid appliance:
These intermediate installation kits can be
used to arrange the iron aid appliance and an
automatic Electrolux washing machine
(60cm wide, front loading) as a space-saving
washer/iron aid stack. The automatic wash-
ing machine is at the bottom and the iron aid
appliance is at the top. Two versions can be
supplied:
without stacker plate
with extractable stacker plate
Read the manual supplied with the installa-
tion kit carefully.
Service
In the event of technical faults, please first
check whether you can remedy the problem
yourself with the help of the operating in-
structions - see chapter What to do if….
If you were not able to remedy the problem
yourself, please contact the Customer Care
Department or one of our service partners.
In order to be able to assist you quickly, we
require the following information:
– Model description
– Product number (PNC)
– Serial number (S No. is on rating plate stuck
to the product - to find it see chapter Product
description ))
– Type of fault
– Any error messages displayed by the ap-
pliance
So that you have the necessary reference
numbers from your appliance at hand, we
recommend that you write them in here:
Model descrip-
tion:
PNC:
S No:
electrolux 17
Electrolux. Thinking of you.
在 www.electrolux.com 上分享更多我们的思维
目录
重要安全信息 18
环境 19
产品说明 20
控制面板 20
首次使用之前 21
程序表 21
分类和准备衣物 22
日常使用 22
清洁和保养 24
如果发生下列情况应如何 ... 26
技术数据 27
干衣机设置 28
测试学会的提 28
安装 29
服务 30
如有更改恕不另行通知
重要安全信息
重要事项! 为了您的安全起见和确保正确使
用,安装和初次使用干衣机之前,请仔细通
读本用户手册,包括其中的提示以及警
告。 为了避免不必要的错误和意外,必须确
保所有使用本干衣机的人员完全清楚其操作
和安全性能。 请妥善保管说明书并在搬迁或
转售干衣机时一并附上说明书,以便使用该
干衣机的所有人都能够正确了解干衣机的使
用和安全信息。
一般安全信息
不管以任何方式改变本产品规格或改造本
产品都非常危险。
本干衣机不可由肢体伤残、感觉障碍以及
缺乏相关经验和知识的人员(包括儿童)
使用,除非在其安全负责人的看管或指导
下才可使用
确定小动物没有爬入烘干槽内。 为避免发
生此情况,请在使用之前检查烘干槽内
部。
任何物体,如硬币、安全别针、钉子、螺
丝钉、石头或任何其他坚硬、尖锐的材料
都会导致重大损害,因此切勿将这些物体
放入干衣机内。
为了避免过量烘干导致的火患危险,请不
要使用本干衣机来烘干下列物品: 垫子、
棉被和类似物品(这类物品会累积热)。
如泡沫塑料(乳胶泡沫)胶乳泡沫、浴
帽、防水纺织品、胶底物品和衣物或装有
泡沫橡胶的枕头等物品都不应放在滚筒干
衣机内烘干
使用、清洁和维护之后务必拔下干衣机的
电源插头。
不论在任何情况下都不应该尝试自行维修
干衣机。 没有经验的人员执行维修工作会
导致受伤或严重故障。 请联系您当地的服
务中心。 始终坚持使用原装备件。
被烹饪油丙酮、汽油、煤油、污迹去除
剂、松节油、蜡和蜡去除剂等物质污染的
衣物,应该先用额外数量的洗衣剂在热水
中洗涤,然后才放入滚筒干衣机内烘干。
爆炸危险: 切勿用干衣机来烘干沾有易燃
溶剂(汽油、甲基化酒精、干洗液和类似
物品)的衣物。 因为这些物质是挥发性的
并可导致爆炸。 仅使用干衣机来烘干用水
洗过的衣物。
火灾危险: 被植物油或烹饪油脏污或浸湿
的衣物会导致火灾危险,请不要用干衣机
来烘干这类衣物。
如果您使用污迹去除剂洗涤衣物,必须执
行额外的漂洗程序之后才将衣物放入滚筒
干衣机。
请确定没有将打火机或火柴意外遗留在要
装入干衣机的衣物口袋中。
警告! 切勿在烘干程序结束之前停止滚
筒干衣机,除非迅速取出有衣物并摊开
使热消散。 火灾危险!
触电危险! 请勿对干衣机喷水。
安装
本干衣机很重。 搬动时请务必小心。
当您拆开干衣机的包装时,请检查并确定
产品没有损坏。 如有疑问,请勿使用干衣
机并联系服务中心。
使用干衣机之前,必须拆除所有的包
装。 若不遵循此指示,会导致产品和财产
严重损坏。 请参阅《用户手册》中的相关
部分。
滚筒烘干程序的最后部分在没有热的情况
下进行(变凉程序),以确保衣物保持在
一个可保证衣物不会损坏的温度。
18 electrolux
安装本干衣机所需的任何电气工作都应该
由合格电工或有能力的人员进行
必须小心确保干衣机没有阻碍电源线。
如果将干衣机放置在有地毯的地面上,请
调整机脚,使干衣机底下的空气可以自由
流通。
安装干衣机后,检查并确保干衣机没有压
住或阻碍电源线。
如果将干衣机放置在洗衣机的上面,就必
需使用堆叠套件(可选附件)。
使用
此干衣机设计于在家庭中使用。 切勿将本
产品用于设计以外的用途。
仅烘干可使用机器烘干的织物。 请遵循衣
物标签上的说明。
请勿在滚筒干衣机中烘干未洗涤的衣物。
请勿超载干衣机。 请参阅《用户手册》中
的相关部分
请勿将还在滴水的衣物放入干衣机内。
请勿将沾有挥发性石油产品的衣物放入机
器内烘干。 如果使用挥发性清洁液,请小
心确保去除衣物上的清洁液才将它放入机
器内。
切勿从电源线拉出插座上的插头; 请务必
握住插头。
如果电源线、控制面板、工作台面或底座
损坏而可以接触滚筒干衣机的内部,切勿
使用滚筒干衣机。
使用衣物柔顺剂或类似产品时,必须按照
衣物柔顺剂说明书的指示进行。
小心 - 热烫表面 : 打开照明时,请勿碰
触机门灯罩表面(仅限于配备内部烘干槽
照明的干衣机)。
儿童安全
本烘干机不可在没有看管的情况下由儿童
或体弱人士使用。
应该看管儿童以确保他们没有玩耍干衣
机。
包装部件(例如塑料袋、聚苯乙烯)可能
会对儿童造成危险 - 窒息危险! 请将它们
存放在儿童无法触及的地方。
将所有洗洁剂它们存放在儿童无法触及的
安全地方。
确定儿童或小动物没有爬入烘干槽内。
环境
产品上或其包装上的标记表示不能把该产品
作为家 庭垃圾般处理。应该将其弃置在电气
和电子设备的废品 回收站点。 为了确保本
品得到正确弃置和避免由于不适当处理废
品 而给环境和人类健康带来潜在的负面效
果,您也可以尽 一分力。 对于本品回收的
更详细信息,请联系您当地的废物回收 部
门、您的家庭垃圾处理服务点或您产品的商
店。
旧器具
警告!
如果您不要再使用该机器,请从插座拔下电
源插头。 剪断电源线并和插头一起废弃。
销毁装载门钩。 这样儿童就不会将自己锁在
机器内而危及生命。
包装材料
包装材料符合环保并可回收利用。 塑料部件
都使用标记识别,例如 >PE<, >PS< 等。请
将包装材料丢弃在社区废物处理设施的适当
容器内。
环境提示
在干衣机内,衣物会变得蓬松和柔软。 因
此在洗涤时不需要使用衣物柔顺剂。
如果您遵循下列说明进行,您的干衣机将
能够以最经济的方式操作:
始终保持干衣机底座上的通风槽通畅无
阻;
使用程序概观中指定的装载容量;
确保安装室内的通风良好;
完成每个烘干程序后,清洁微细过滤器
和细微滤网;
烘干之前妥善使衣物脱水。
能源的消耗将取决于洗衣机上设置的脱
水转速。 较高脱水转速 - 较低能源消
耗。
electrolux 19
产品说明
1
3
4
2
5
6
7
8
9
10
1 控制面板
2 绒毛滤网
3 装载门(可反转)
4 通风栅
5 可调机脚
6 带冷凝水容器的隔间
7 用于打开底座门的按钮
8 铭牌
9 热交换器
10 热交换器门
控制面板
1 2 4
3
5
1 程序旋钮和开关 2 "延迟计时器"按钮
20 electrolux
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32

Electrolux EDC67550W User manual

Category
Tumble dryers
Type
User manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

in other languages